igt@kms_pm_rpm@basic-pci-d3-state on bat-adls-5@linus-v6.7-rc5 Test details

Detail	Value
Duration	4.36 seconds
Igt-Version	IGT-Version: 1.28-g0e1019715 (x86_64) (Linux: 6.7.0-rc5-linus-v6.7-rc5-ga39b6ac3781d+ x86_64)
Out	Using IGT_SRANDOM=1702248711 for randomisation Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 set_property_atomic+0x87/0x160 drm_mode_obj_set_property_ioctl+0xc0/0x110 drm_ioctl_kernel+0xbd/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x179/0x2c0 [i915] intel_gt_handle_error+0x2b8/0x420 [i915] intel_gt_debugfs_reset_store+0x5c/0xc0 [i915] i915_wedged_set+0x1d/0x40 [i915] simple_attr_write_xsigned.constprop.0+0xb4/0x110 full_proxy_write+0x58/0x80 Wakeref count: 1 Wakeref x1 taken at: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] __intel_display_power_put_async+0x3d/0x160 [i915] hsw_get_pipe_config+0x155/0xa70 [i915] intel_crtc_get_pipe_config+0x1f/0x50 [i915] intel_modeset_verify_crtc+0xe5/0x530 [i915] intel_atomic_commit_tail+0x7b4/0xd50 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (4.357s)
Err	Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (4.357s)
Dmesg	<6> [193.988742] Console: switching to colour dummy device 80x25 <6> [193.989013] [IGT] kms_pm_rpm: executing <7> [193.992761] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [194.000714] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] <7> [194.000726] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [194.001002] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] disconnected <7> [194.001891] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] <7> [194.001896] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [194.002091] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] disconnected <7> [194.002914] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [194.002919] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [194.003111] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [194.003760] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] <7> [194.003766] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [194.003928] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] disconnected <7> [194.004392] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] <7> [194.004396] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [194.004549] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] disconnected <7> [194.005038] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] <7> [194.005042] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [194.005181] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] disconnected <7> [194.005709] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] <7> [194.005713] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [194.006716] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [194.007744] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [194.008161] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [194.008263] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [194.008358] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [194.008464] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [194.008470] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [194.008473] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [194.008475] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [194.008487] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [194.008581] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [194.009434] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [194.009738] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [194.010637] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes : <7> [194.010648] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [194.010695] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] <7> [194.010704] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [194.011064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] disconnected <7> [194.011084] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] <7> [194.011087] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [194.011198] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] disconnected <7> [194.011211] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [194.011213] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [194.011333] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [194.011345] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] <7> [194.011348] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [194.011462] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] disconnected <7> [194.011474] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] <7> [194.011477] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [194.011589] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] disconnected <7> [194.011600] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] <7> [194.011602] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [194.011741] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] disconnected <7> [194.011783] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] <7> [194.011787] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [194.012590] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [194.013564] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [194.013872] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [194.014086] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [194.014183] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [194.014289] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [194.014293] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [194.014297] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [194.014300] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [194.014309] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [194.014411] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [194.015229] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [194.015497] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [194.016346] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes : <7> [194.016355] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [194.016486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] <7> [194.016495] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [194.016789] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] disconnected <7> [194.016888] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] <7> [194.016891] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [194.017012] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] disconnected <7> [194.017067] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [194.017070] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [194.017193] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [194.017243] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] <7> [194.017246] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [194.017366] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] disconnected <7> [194.017416] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] <7> [194.017418] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [194.017537] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] disconnected <7> [194.017582] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] <7> [194.017584] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [194.017698] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] disconnected <7> [194.017901] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:282] <7> [195.039352] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [195.039605] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.enable (expected 1, found 0) <7> [195.040337] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.active (expected 1, found 0) <7> [195.040903] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1) <7> [195.041424] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in lane_count (expected 2, found 0) <7> [195.042034] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7654604/8388608 link 318941/524288, found tu 0, data 0/0 link 0/0) <7> [195.042631] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000) <7> [195.043216] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0) <7> [195.043795] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0) <7> [195.044345] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 2080, found 0) <7> [195.044965] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0) <7> [195.045511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 2080, found 0) <7> [195.045647] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 1968, found 0) <7> [195.045775] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2000, found 0) <7> [195.045892] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1280, found 0) <7> [195.046005] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1280, found 0) <7> [195.046117] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1283, found 0) <7> [195.046227] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1293, found 0) <7> [195.046337] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1317, found 0) <7> [195.046447] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1317, found 0) <7> [195.046556] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0) <7> [195.046665] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 2080, found 0) <7> [195.046792] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0) <7> [195.046906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 2080, found 0) <7> [195.047018] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 1968, found 0) <7> [195.047130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2000, found 0) <7> [195.047239] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1280, found 0) <7> [195.047348] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1280, found 0) <7> [195.047458] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1283, found 0) <7> [195.047567] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1293, found 0) <7> [195.047677] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1317, found 0) <7> [195.047796] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1317, found 0) <7> [195.047906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0) <7> [195.048016] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0) <7> [195.048124] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0) <7> [195.048233] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in enhanced_framing (expected yes, found no) <7> [195.048341] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0) <7> [195.048450] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 164250, found 0) <7> [195.048556] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 164250, found 0) <7> [195.048664] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 270000, found 0) <7> [195.048780] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [195.048889] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:80:pipe A] releasing DPLL 0 <7> [195.049034] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no <7> [195.049168] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [195.049303] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0 <7> [195.049400] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb (2006 - 2048) -> ( 0 - 0), size 42 -> 0 <7> [195.049496] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [195.049590] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [195.049683] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [195.049796] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [195.049900] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0 <7> [195.050015] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 0 <7> [195.050127] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 0 <7> [195.050237] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 0 <7> [195.050345] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 0 <7> [195.050453] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0 <7> [195.050560] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0 <7> [195.050668] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0 <7> [195.050810] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [195.050924] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [195.051038] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [modeset] <7> [195.051150] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [195.051259] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [195.051366] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [195.051473] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [195.051580] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [195.051687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [195.051856] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1 <7> [195.059704] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [195.262003] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:236:eDP-1] set backlight PWM = 0 <7> [195.262966] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [195.275019] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power off <7> [195.275366] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000 <7> [195.275599] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power off time <7> [195.275936] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - short <7> [195.276156] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [195.329984] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [195.330558] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [195.331229] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A] <7> [195.331225] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [195.331860] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [195.332419] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [195.333026] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A] <7> [195.333558] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B] <7> [195.334116] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C] <7> [195.334627] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A] <7> [195.335107] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B] <7> [195.335543] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C] <7> [195.336004] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D] <7> [195.336427] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D] <7> [195.336872] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E] <7> [195.337295] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A] <7> [195.337710] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B] <7> [195.338191] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C] <7> [195.338635] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D] <7> [195.339160] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1] <7> [195.339657] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [195.340199] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [195.340685] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2 <7> [195.341202] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3 <7> [195.341707] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [195.342326] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [195.342906] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [195.343961] [drm:drm_mode_setcrtc] [CRTC:131:pipe B] <7> [195.344306] [drm:drm_mode_setcrtc] [CRTC:182:pipe C] <7> [195.344554] [drm:drm_mode_setcrtc] [CRTC:233:pipe D] <7> [195.395870] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [195.396460] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long <7> [195.396977] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [195.397594] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [195.550015] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [195.550673] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [195.551342] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [195.553306] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [195.555169] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [195.558205] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [195.560595] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [195.561870] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [195.562168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [195.562392] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [195.562510] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [195.562703] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [195.650177] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state <7> [195.659895] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [195.672615] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [195.672972] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [195.673460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [195.673984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [195.674466] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [195.675024] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [195.675576] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [195.676121] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [195.676610] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY E (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [195.677044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [195.677989] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [195.678422] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [195.679026] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [195.679853] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [195.680030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [195.695116] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [195.697401] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [195.697624] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [195.697881] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [195.698552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [195.699991] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [195.700123] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [195.700405] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on <7> [195.700529] [drm:drm_mode_setcrtc] [CRTC:131:pipe B] <7> [195.700526] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [195.934139] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [195.934656] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [195.935236] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [195.935653] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 panel power wasn't enabled <7> [195.970333] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [195.970879] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long <7> [195.971395] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [195.972008] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [196.144105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [196.145479] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [196.146050] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [196.146541] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [196.147044] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [196.147691] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [196.147698] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [196.147702] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [196.147704] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [196.147726] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [196.147833] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [196.148629] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [196.148730] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [196.149384] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [196.149729] [drm:drm_mode_setcrtc] [CRTC:182:pipe C] <7> [196.149723] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [196.149871] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [196.150005] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [196.150144] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [196.150266] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [196.150486] [drm:drm_mode_setcrtc] [CRTC:233:pipe D] <7> [199.150061] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD off <7> [199.150709] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [199.151355] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [199.152281] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [199.152880] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [199.153489] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [199.155207] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [199.155794] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [199.157621] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [199.159938] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [199.161213] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [199.161397] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [199.161608] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [199.161720] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [199.161875] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [199.260271] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [199.260382] [drm:drm_mode_setcrtc] [CONNECTOR:236:eDP-1] <7> [199.260568] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:236:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [199.261258] i915 0000:00:02.0: [drm:intel_dp_compute_config_link_bpp_limits [i915]] [ENCODER:235:DDI A/PHY A][CRTC:80:pipe A] DP link limits: pixel clock 164250 kHz DSC off max lanes 2 max rate 540000 max pipe_bpp 24 max link_bpp 24.0000 <7> [199.261720] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 2 clock 270000 bpp 24 <7> [199.262196] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 492750 available 540000 <7> [199.262613] i915 0000:00:02.0: [drm:intel_dp_audio_compute_config [i915]] [CONNECTOR:236:eDP-1] SDP split enable: no <7> [199.263050] i915 0000:00:02.0: [drm:intel_psr_compute_config [i915]] PSR2 is defeatured for this platform <7> [199.263504] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [199.264032] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:235:DDI A/PHY A] [CRTC:80:pipe A] <7> [199.264478] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.enable (expected 0, found 1) <7> [199.265015] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.active (expected 0, found 1) <7> [199.265512] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0) <7> [199.265637] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in lane_count (expected 0, found 2) <7> [199.265754] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 7654604/8388608 link 318941/524288) <7> [199.265867] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100) <7> [199.265978] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1) <7> [199.266088] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920) <7> [199.266199] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 2080) <7> [199.266309] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920) <7> [199.266417] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 2080) <7> [199.266528] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 1968) <7> [199.266643] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2000) <7> [199.266763] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1280) <7> [199.266874] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1280) <7> [199.266985] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1283) <7> [199.267095] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1293) <7> [199.267204] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1317) <7> [199.267313] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1317) <7> [199.267421] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920) <7> [199.267529] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 2080) <7> [199.267637] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920) <7> [199.267751] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2080) <7> [199.267859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 1968) <7> [199.267968] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2000) <7> [199.268075] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1280) <7> [199.268182] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1280) <7> [199.268294] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1283) <7> [199.268409] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1293) <7> [199.268523] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1317) <7> [199.268635] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1317) <7> [199.268750] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1) <7> [199.268860] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2) <7> [199.268972] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8) <7> [199.269081] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in enhanced_framing (expected no, found yes) <7> [199.269191] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24) <7> [199.269306] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 164250) <7> [199.269420] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 164250) <7> [199.269534] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 0, found 270000) <7> [199.269644] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [199.269799] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0x3 (total dbuf slices 0x3), mbus joined? no->no <7> [199.269922] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x0 -> 0x3, ddb (0 - 0) -> (0 - 2048), active pipes 0x0 -> 0x1 <7> [199.270048] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006 <7> [199.270149] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (2006 - 2048), size 0 -> 42 <7> [199.270247] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm <7> [199.270344] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0 <7> [199.270445] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47 <7> [199.270546] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48 <7> [199.270645] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1 <7> [199.270769] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 657 <7> [199.270888] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 657 <7> [199.270997] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 657 <7> [199.271105] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 657 <7> [199.271212] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657 <7> [199.271319] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657 <7> [199.271425] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657 <7> [199.271540] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (82125 kHz) > [CRTC:80:pipe A] min cdclk (0 kHz) <7> [199.271650] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (12833 kHz) > old min cdclk (0 kHz) <7> [199.271764] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [199.271871] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [199.271980] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0 <7> [199.272090] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0 <7> [199.272200] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset] <7> [199.272311] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [199.272420] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7> [199.272528] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [199.272635] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [199.272741] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [199.272859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [199.272970] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 2; data_m: 7654604, data_n: 8388608, link_m: 318941, link_n: 524288, tu: 64 <7> [199.273082] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 2; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [199.273191] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled <7> [199.273299] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [199.273405] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [199.273512] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0 <7> [199.273514] i915 0000:00:02.0: pixelformat: RGB <7> [199.273516] i915 0000:00:02.0: colorimetry: sRGB <7> [199.273517] i915 0000:00:02.0: bpc: 0 <7> [199.273518] i915 0000:00:02.0: dynamic range: VESA range <7> [199.273519] i915 0000:00:02.0: content type: Not defined <7> [199.273520] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 1316, vmax: 3948, pipeline full: 34, guardband: 0 flipline: 1317, vmin vblank: 1281, vmax vblank: 3912 <7> [199.273627] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [199.273733] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa <7> [199.273850] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=164250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1280 vb=1280-1317 vs=1283-1293 vt=1317, flags=0xa <7> [199.273957] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x40 0xa <7> [199.274064] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=164250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1280 vb=1280-1317 vs=1283-1293 vt=1317, flags=0xa <7> [199.274171] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 270000, pipe src: 1920x1280+0+0, pixel rate 164250 <7> [199.274275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 102, ips linetime: 0 <7> [199.274380] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [199.274485] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [199.274592] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [199.274703] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x88, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [199.274818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [199.274928] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [199.275036] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [199.275142] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [199.275248] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [199.275354] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [199.275459] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [199.275565] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [199.275670] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [199.275782] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [199.275886] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [199.275990] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [199.276098] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:282] 1920x1280 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [199.276211] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [199.276320] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1920.000000x1280.000000+0.000000+0.000000 dst: 1920x1280+0+0 <7> [199.276430] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [199.276538] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [199.276645] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [199.276757] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [199.276863] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [199.289223] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [199.289294] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [199.289420] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [199.289563] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [199.289744] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [199.289949] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [199.290119] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [199.290288] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [199.290465] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY E (Voltage/Process Info : 0.85V dot0 (low-voltage)) <7> [199.290630] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [199.290805] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [199.290921] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [199.291099] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [199.291819] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [199.291930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [199.303632] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [199.305880] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [199.305951] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [199.306689] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [199.307349] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [199.308672] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A] <7> [199.308782] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B] <7> [199.308884] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C] <7> [199.308987] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A] <7> [199.309089] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B] <7> [199.309187] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C] <7> [199.309284] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D] <7> [199.309380] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D] <7> [199.309476] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E] <7> [199.309571] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A] <7> [199.309665] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B] <7> [199.309768] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C] <7> [199.309864] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D] <7> [199.309959] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [199.310068] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [199.310175] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2 <7> [199.310285] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3 <7> [199.310396] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [199.310542] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [199.310656] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A] <7> [199.310766] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [199.310923] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power on <7> [199.311029] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [199.758069] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [199.758643] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [199.759238] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power on <7> [199.759786] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [199.794126] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010 <7> [199.794745] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long <7> [199.795321] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [199.796016] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A] <7> [199.970277] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [199.970939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [199.971832] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on <7> [199.972399] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [199.975088] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c2 41 00 00 01 c0 02 00 00 00 00 0b 80 <7> [199.975162] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Reloading eDP link rates <7> [199.976633] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 03 <7> [199.977987] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] 8b/10b, lanes: 2, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [199.978200] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [199.979513] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Clock recovery OK <7> [199.979984] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [199.982424] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [199.982893] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Link Training passed at link rate = 270000, lane count = 2 <7> [199.983975] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [199.984680] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [199.985215] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [199.985696] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:236:eDP-1] Performing OUI wait (0 ms) <7> [199.986942] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:236:eDP-1] set backlight PWM = 96000 <7> [200.001599] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [200.002317] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1 <7> [200.003901] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1] <7> [200.004473] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [200.005422] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [200.006375] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1] <7> [200.007849] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <6> [200.008479] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS <7> [200.008989] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [200.009417] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [200.009867] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000 <7> [200.010274] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [200.010737] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz <7> [200.010785] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc. <7> [200.010799] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41 <7> [200.010812] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0 <7> [200.010857] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes <7> [200.011264] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [200.012462] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [200.012941] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [200.014065] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1] <7> [200.014532] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1] <7> [200.014988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [200.015404] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3] <7> [200.015856] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2] <7> [200.016258] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4] <7> [200.026694] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [200.027503] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [200.028430] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <7> [200.041490] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [200.042219] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [200.081941] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:282] from all active usage due to RMFB ioctl <7> [200.082069] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:282] is removed <7> [200.082195] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0 <7> [200.082719] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [200.083281] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [200.083821] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [200.084263] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [200.084697] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0 <7> [200.085291] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 0 <7> [200.085837] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 0 <7> [200.086330] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 0 <7> [200.086870] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 0 <7> [200.087384] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0 <7> [200.087927] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0 <7> [200.088425] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0 <7> [200.089100] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1 <7> [200.103040] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006 <7> [200.103568] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm,swm,stwm <7> [200.104107] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0 <7> [200.104569] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47 <7> [200.105099] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48 <7> [200.105555] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1 <7> [200.106124] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 657 <7> [200.106630] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 657 <7> [200.107287] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 657 <7> [200.107820] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 657 <7> [200.108303] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657 <7> [200.108736] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657 <7> [200.109243] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657 <7> [200.118321] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1 <6> [200.120438] [IGT] kms_pm_rpm: exiting, ret=0 <6> [200.135332] Console: switching to colour frame buffer device 240x80

<7> [194.000714] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1]

<7> [194.000726] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [194.001002] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] disconnected

<7> [194.001891] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1]

<7> [194.001896] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [194.002091] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] disconnected

<7> [194.002914] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [194.002919] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [194.003111] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [194.003760] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3]

<7> [194.003766] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [194.003928] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] disconnected

<7> [194.004392] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2]

<7> [194.004396] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [194.004549] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] disconnected

<7> [194.005038] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4]

<7> [194.005042] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [194.005181] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] disconnected

<7> [194.005709] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]

<7> [194.005713] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [194.006716] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [194.007744] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [194.008161] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [194.008263] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [194.008358] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [194.008464] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [194.008470] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [194.008473] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [194.008475] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [194.008487] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [194.008581] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [194.009434] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [194.009738] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [194.010637] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :

<7> [194.010648] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [194.010695] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1]

<7> [194.010704] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [194.011064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] disconnected

<7> [194.011084] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1]

<7> [194.011087] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [194.011198] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] disconnected

<7> [194.011211] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [194.011213] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [194.011333] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [194.011345] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3]

<7> [194.011348] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [194.011462] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] disconnected

<7> [194.011474] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2]

<7> [194.011477] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [194.011589] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] disconnected

<7> [194.011600] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4]

<7> [194.011602] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [194.011741] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] disconnected

<7> [194.011783] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]

<7> [194.011787] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [194.012590] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [194.013564] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [194.013872] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [194.014086] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [194.014183] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [194.014289] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [194.014293] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [194.014297] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [194.014300] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [194.014309] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [194.014411] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [194.015229] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [194.015497] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [194.016346] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :

<7> [194.016355] [drm:drm_mode_debug_printmodeline] Modeline "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [194.016486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1]

<7> [194.016495] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [194.016789] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:245:HDMI-A-1] disconnected

<7> [194.016888] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1]

<7> [194.016891] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [194.017012] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:254:DP-1] disconnected

<7> [194.017067] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [194.017070] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [194.017193] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [194.017243] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3]

<7> [194.017246] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [194.017366] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:267:HDMI-A-3] disconnected

<7> [194.017416] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2]

<7> [194.017418] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [194.017537] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:DP-2] disconnected

<7> [194.017582] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4]

<7> [194.017584] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [194.017698] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:279:HDMI-A-4] disconnected

<7> [195.039605] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)

<7> [195.040337] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.active (expected 1, found 0)

<7> [195.040903] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in cpu_transcoder (expected 0, found -1)

<7> [195.041424] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in lane_count (expected 2, found 0)

<7> [195.042034] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 7654604/8388608 link 318941/524288, found tu 0, data 0/0 link 0/0)

<7> [195.042631] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)

<7> [195.043216] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)

<7> [195.043795] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 1920, found 0)

<7> [195.044345] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 2080, found 0)

<7> [195.044965] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 1920, found 0)

<7> [195.045511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 2080, found 0)

<7> [195.045647] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 1968, found 0)

<7> [195.045775] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 2000, found 0)

<7> [195.045892] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1280, found 0)

<7> [195.046005] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1280, found 0)

<7> [195.046117] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1283, found 0)

<7> [195.046227] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1293, found 0)

<7> [195.046337] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1317, found 0)

<7> [195.046447] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1317, found 0)

<7> [195.046556] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 1920, found 0)

<7> [195.046665] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 2080, found 0)

<7> [195.046792] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 1920, found 0)

<7> [195.046906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 2080, found 0)

<7> [195.047018] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 1968, found 0)

<7> [195.047130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 2000, found 0)

<7> [195.047239] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1280, found 0)

<7> [195.047348] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1280, found 0)

<7> [195.047458] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1283, found 0)

<7> [195.047567] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1293, found 0)

<7> [195.047677] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1317, found 0)

<7> [195.047796] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1317, found 0)

<7> [195.047906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)

<7> [195.048016] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)

<7> [195.048124] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)

<7> [195.048233] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in enhanced_framing (expected yes, found no)

<7> [195.048341] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)

<7> [195.048450] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 164250, found 0)

<7> [195.048556] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 164250, found 0)

<7> [195.048664] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 270000, found 0)

<7> [195.048780] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [195.048889] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:80:pipe A] releasing DPLL 0

<7> [195.049034] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no

<7> [195.049168] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0x0, ddb (0 - 2048) -> (0 - 0), active pipes 0x1 -> 0x0

<7> [195.049303] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0

<7> [195.049400] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb (2006 - 2048) -> ( 0 - 0), size 42 -> 0

<7> [195.049496] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [195.049590] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [195.049683] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [195.049796] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [195.049900] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0

<7> [195.050015] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 0

<7> [195.050127] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 0

<7> [195.050237] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 0

<7> [195.050345] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 0

<7> [195.050453] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0

<7> [195.050560] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0

<7> [195.050668] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0

<7> [195.050810] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [195.050924] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [195.051038] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: no [modeset]

<7> [195.051150] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [195.051259] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [195.051366] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [195.051473] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [195.051580] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [195.051687] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [195.051856] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1

<7> [195.059704] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [195.262003] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:236:eDP-1] set backlight PWM = 0

<7> [195.262966] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [195.275019] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power off

<7> [195.275366] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x00000009, pins 0x00000010, long 0x00000000

<7> [195.275599] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [195.275936] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - short

<7> [195.276156] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [195.329984] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [195.330558] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [195.331229] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A]

<7> [195.331225] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [195.331860] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [195.332419] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [195.333026] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A]

<7> [195.333558] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B]

<7> [195.334116] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C]

<7> [195.334627] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A]

<7> [195.335107] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B]

<7> [195.335543] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C]

<7> [195.336004] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D]

<7> [195.336427] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D]

<7> [195.336872] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E]

<7> [195.337295] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A]

<7> [195.337710] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B]

<7> [195.338191] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C]

<7> [195.338635] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D]

<7> [195.339160] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1]

<7> [195.339657] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [195.340199] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [195.340685] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2

<7> [195.341202] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3

<7> [195.341707] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [195.342326] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [195.342906] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [195.395870] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010

<7> [195.396460] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long

<7> [195.396977] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [195.397594] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [195.550015] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [195.550673] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [195.551342] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [195.553306] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [195.555169] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [195.558205] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled

<7> [195.560595] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [195.561870] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [195.562168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [195.562392] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [195.562510] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [195.562703] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<6> [195.650177] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state

<7> [195.672615] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [195.672972] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [195.673460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [195.673984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [195.674466] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [195.675024] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [195.675576] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [195.676121] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [195.676610] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY E (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [195.677044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [195.677989] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [195.678422] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [195.679026] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [195.679853] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [195.680030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [195.695116] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<7> [195.697401] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [195.697624] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [195.697881] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [195.698552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [195.699991] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [195.700123] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [195.700405] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on

<7> [195.700526] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [195.934139] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [195.934656] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [195.935236] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [195.935653] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 panel power wasn't enabled

<7> [195.970333] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010

<7> [195.970879] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long

<7> [195.971395] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [195.972008] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [196.144105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [196.145479] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [196.146050] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [196.146541] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [196.147044] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [196.147691] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [196.147698] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [196.147702] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [196.147704] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [196.147726] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [196.147833] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [196.148629] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [196.148730] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [196.149384] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [196.149723] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [196.149871] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [196.150005] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [196.150144] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [196.150266] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [199.150061] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD off

<7> [199.150709] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [199.151355] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [199.152281] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [199.152880] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [199.153489] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [199.155207] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [199.155794] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [199.157621] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled

<7> [199.159938] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [199.161213] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [199.161397] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [199.161608] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [199.161720] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [199.161875] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<7> [199.260568] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:236:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [199.261258] i915 0000:00:02.0: [drm:intel_dp_compute_config_link_bpp_limits [i915]] [ENCODER:235:DDI A/PHY A][CRTC:80:pipe A] DP link limits: pixel clock 164250 kHz DSC off max lanes 2 max rate 540000 max pipe_bpp 24 max link_bpp 24.0000

<7> [199.261720] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 2 clock 270000 bpp 24

<7> [199.262196] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 492750 available 540000

<7> [199.262613] i915 0000:00:02.0: [drm:intel_dp_audio_compute_config [i915]] [CONNECTOR:236:eDP-1] SDP split enable: no

<7> [199.263050] i915 0000:00:02.0: [drm:intel_psr_compute_config [i915]] PSR2 is defeatured for this platform

<7> [199.263504] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [199.264032] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:235:DDI A/PHY A] [CRTC:80:pipe A]

<7> [199.264478] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)

<7> [199.265015] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.active (expected 0, found 1)

<7> [199.265512] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 0)

<7> [199.265637] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in lane_count (expected 0, found 2)

<7> [199.265754] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 7654604/8388608 link 318941/524288)

<7> [199.265867] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)

<7> [199.265978] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)

<7> [199.266088] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 1920)

<7> [199.266199] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 2080)

<7> [199.266309] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 1920)

<7> [199.266417] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 2080)

<7> [199.266528] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 1968)

<7> [199.266643] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 2000)

<7> [199.266763] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1280)

<7> [199.266874] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1280)

<7> [199.266985] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1283)

<7> [199.267095] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1293)

<7> [199.267204] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1317)

<7> [199.267313] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1317)

<7> [199.267421] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 1920)

<7> [199.267529] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 2080)

<7> [199.267637] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 1920)

<7> [199.267751] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 2080)

<7> [199.267859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 1968)

<7> [199.267968] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 2000)

<7> [199.268075] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1280)

<7> [199.268182] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1280)

<7> [199.268294] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1283)

<7> [199.268409] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1293)

<7> [199.268523] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1317)

<7> [199.268635] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1317)

<7> [199.268750] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)

<7> [199.268860] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)

<7> [199.268972] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)

<7> [199.269081] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in enhanced_framing (expected no, found yes)

<7> [199.269191] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)

<7> [199.269306] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 164250)

<7> [199.269420] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 164250)

<7> [199.269534] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 0, found 270000)

<7> [199.269644] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [199.269799] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x1 -> 0x3 (total dbuf slices 0x3), mbus joined? no->no

<7> [199.269922] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x0 -> 0x3, ddb (0 - 0) -> (0 - 2048), active pipes 0x0 -> 0x1

<7> [199.270048] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006

<7> [199.270149] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (2006 - 2048), size 0 -> 42

<7> [199.270247] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm

<7> [199.270344] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0

<7> [199.270445] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47

<7> [199.270546] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48

<7> [199.270645] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1

<7> [199.270769] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 657

<7> [199.270888] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 657

<7> [199.270997] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 657

<7> [199.271105] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 657

<7> [199.271212] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657

<7> [199.271319] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657

<7> [199.271425] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657

<7> [199.271540] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (82125 kHz) > [CRTC:80:pipe A] min cdclk (0 kHz)

<7> [199.271650] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (12833 kHz) > old min cdclk (0 kHz)

<7> [199.271764] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [199.271871] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [199.271980] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0

<7> [199.272090] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0

<7> [199.272200] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset]

<7> [199.272311] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [199.272420] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0

<7> [199.272528] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [199.272635] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [199.272741] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [199.272859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [199.272970] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 2; data_m: 7654604, data_n: 8388608, link_m: 318941, link_n: 524288, tu: 64

<7> [199.273082] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 2; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [199.273191] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] fec: disabled, enhanced framing: enabled

<7> [199.273299] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [199.273405] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [199.273512] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0

<7> [199.273520] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 1316, vmax: 3948, pipeline full: 34, guardband: 0 flipline: 1317, vmin vblank: 1281, vmax vblank: 3912

<7> [199.273627] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [199.273733] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x48 0xa

<7> [199.273850] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=164250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1280 vb=1280-1317 vs=1283-1293 vt=1317, flags=0xa

<7> [199.273957] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1920x1280": 60 164250 1920 1968 2000 2080 1280 1283 1293 1317 0x40 0xa

<7> [199.274064] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=164250, hd=1920 hb=1920-2080 hs=1968-2000 ht=2080, vd=1280 vb=1280-1317 vs=1283-1293 vt=1317, flags=0xa

<7> [199.274171] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 270000, pipe src: 1920x1280+0+0, pixel rate 164250

<7> [199.274275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 102, ips linetime: 0

<7> [199.274380] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [199.274485] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [199.274592] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [199.274703] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x88, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [199.274818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [199.274928] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [199.275036] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [199.275142] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [199.275248] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [199.275354] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [199.275459] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [199.275565] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [199.275670] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [199.275782] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [199.275886] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [199.275990] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [199.276098] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:282] 1920x1280 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [199.276211] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [199.276320] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1920.000000x1280.000000+0.000000+0.000000 dst: 1920x1280+0+0

<7> [199.276430] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [199.276538] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [199.276645] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [199.276757] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [199.276863] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [199.289223] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [199.289294] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [199.289420] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [199.289563] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [199.289744] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY A (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [199.289949] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY B (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [199.290119] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY C (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [199.290288] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY D (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [199.290465] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Initializing combo PHY E (Voltage/Process Info : 0.85V dot0 (low-voltage))

<7> [199.290630] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [199.290805] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [199.290921] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [199.291099] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [199.291819] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [199.291930] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [199.303632] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<7> [199.305880] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [199.305951] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [199.306689] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [199.307349] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [199.308672] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:235:DDI A/PHY A]

<7> [199.308782] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:244:DDI TC1/PHY B]

<7> [199.308884] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:253:DDI TC2/PHY C]

<7> [199.308987] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:255:DP-MST A]

<7> [199.309089] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:256:DP-MST B]

<7> [199.309187] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:257:DP-MST C]

<7> [199.309284] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:258:DP-MST D]

<7> [199.309380] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:266:DDI TC3/PHY D]

<7> [199.309476] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:270:DDI TC4/PHY E]

<7> [199.309571] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:272:DP-MST A]

<7> [199.309665] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:273:DP-MST B]

<7> [199.309768] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:274:DP-MST C]

<7> [199.309864] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:275:DP-MST D]

<7> [199.309959] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [199.310068] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [199.310175] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2

<7> [199.310285] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3

<7> [199.310396] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [199.310542] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [199.310656] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A]

<7> [199.310766] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [199.310923] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turn panel power on

<7> [199.311029] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [199.758069] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [199.758643] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [199.759238] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 wait for panel power on

<7> [199.759786] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063

<7> [199.794126] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000000a, pins 0x00000010, long 0x00000010

<7> [199.794745] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:235:DDI A/PHY A] - long

<7> [199.795321] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [199.796016] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:235:DDI A/PHY A]

<7> [199.970277] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [199.970939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [199.971832] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 turning VDD on

<7> [199.972399] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:235:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [199.975088] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 0a c2 41 00 00 01 c0 02 00 00 00 00 0b 80

<7> [199.975162] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Reloading eDP link rates

<7> [199.976633] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 03

<7> [199.977987] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] 8b/10b, lanes: 2, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [199.978200] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [199.979513] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Clock recovery OK

<7> [199.979984] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [199.982424] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [199.982893] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:236:eDP-1][ENCODER:235:DDI A/PHY A][DPRX] Link Training passed at link rate = 270000, lane count = 2

<7> [199.983975] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [199.984680] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [199.985215] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [199.985696] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:236:eDP-1] Performing OUI wait (0 ms)

<7> [199.986942] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:236:eDP-1] set backlight PWM = 96000

<7> [200.001599] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [200.002317] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1

<7> [200.003901] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:236:eDP-1]

<7> [200.004473] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [200.005422] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [200.006375] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]

<7> [200.007849] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<6> [200.008479] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS

<7> [200.008989] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [200.009417] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [200.009867] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 378000, 432000, 540000

<7> [200.010274] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [200.010737] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 20 Hz - 60 Hz

<7> [200.010785] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.

<7> [200.010799] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor LQ123N1JX41

<7> [200.010812] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 32, SAD count 0

<7> [200.010857] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: yes

<7> [200.011264] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [200.012462] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [200.012941] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [200.014065] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:245:HDMI-A-1]

<7> [200.014532] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:254:DP-1]

<7> [200.014988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [200.015404] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:267:HDMI-A-3]

<7> [200.015856] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:271:DP-2]

<7> [200.016258] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:279:HDMI-A-4]

<7> [200.026694] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [200.027503] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [200.028430] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010

<7> [200.041490] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3

<7> [200.042219] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [200.081941] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:282] from all active usage due to RMFB ioctl

<7> [200.082069] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:282] is removed

<7> [200.082195] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2006) -> ( 0 - 0), size 2006 -> 0

<7> [200.082719] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [200.083281] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [200.083821] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [200.084263] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [200.084697] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 0 num active planes 0

<7> [200.085291] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 0

<7> [200.085837] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 0

<7> [200.086330] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 0

<7> [200.086870] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 0

<7> [200.087384] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 0

<7> [200.087927] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 0

<7> [200.088425] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 0

<7> [200.089100] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1

<7> [200.103040] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 2006), size 0 -> 2006

<7> [200.103568] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm,*swm,*stwm

<7> [200.104107] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 2, 3, 3, 3, 4, 8, 12, 0, 2, 0

<7> [200.104569] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 16, 33, 49, 49, 49, 65, 129, 193, 30, 33, 47

<7> [200.105099] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 19, 38, 55, 55, 55, 73, 143, 214, 31, 38, 48

<7> [200.105555] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 657000 num active planes 1

<7> [200.106124] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 6471 required 657

<7> [200.106630] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 10602 required 657

<7> [200.107287] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 12291 required 657

<7> [200.107820] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 13130 required 657

<7> [200.108303] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 657

<7> [200.108736] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 51200 required 657

<7> [200.109243] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 68267 required 657

<7> [200.118321] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1

<6> [200.135332] Console: switching to colour frame buffer device 240x80

Results for igt@kms_pm_rpm@basic-pci-d3-state