Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-gc7298ec10 (x86_64) (Linux: 6.7.0-rc4-linus-v6.7-rc4-g33cc938e65a9+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xbf/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x7c/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x179/0x2c0 [i915]
   intel_dmc_debugfs_status_show+0x349/0x450 [i915]
   seq_read_iter+0x114/0x450
   seq_read+0xab/0xe0
   full_proxy_read+0x5b/0x80
   vfs_read+0xac/0x2e0
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa49/0xd40 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xbf/0x150
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.274s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.274s)
Dmesg
<6> [74.517824] Console: switching to colour dummy device 80x25
<6> [74.517877] [IGT] kms_pm_rpm: executing
<7> [74.526482] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [74.530392] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [74.530399] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [74.530588] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [74.531045] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [74.531049] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [74.532260] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.533360] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.534138] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [74.534672] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [74.534678] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [74.535099] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.535214] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.535692] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.535838] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.535842] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.535969] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.540078] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.540084] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.540201] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [74.540521] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [74.540526] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [74.540735] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [74.540750] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [74.540753] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [74.542007] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.543089] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.543838] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [74.543858] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [74.543862] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [74.544271] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.544434] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.544864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.545012] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.545015] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.545128] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.549289] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.549294] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.549411] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [74.549438] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [74.549442] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [74.549634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [74.549743] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [74.549747] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [74.550823] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [74.551859] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [74.552634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [74.552695] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [74.552699] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [74.553119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.553234] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [74.553713] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [74.553859] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.553863] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [74.553974] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [74.558043] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [74.558048] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [74.558166] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [74.725648] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [74.726241] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [74.726799] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [74.727443] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [74.728602] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [85.607285] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [85.611412] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [85.634682] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [85.641125] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [85.642328] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [85.642737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [85.643083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [85.643796] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [85.645360] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [85.645363] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [85.645917] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [85.646308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [85.648363] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [85.649086] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [85.649668] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [85.650811] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.650969] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [85.651367] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.651545] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.651549] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [85.651694] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [85.655946] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.655951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [85.656193] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [85.765668] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [85.765925] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [85.766131] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [85.766330] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [85.767025] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [85.767925] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [85.772142] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [85.857789] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state
<7> [85.869928] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [85.882312] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [85.892464] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [85.893425] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [85.893826] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [85.894640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [85.895831] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [85.896187] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [85.896627] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [85.896561] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [85.898055] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [85.898988] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [85.899616] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [85.900154] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.900360] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [85.900847] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [85.901086] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.901094] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [85.901295] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [85.905667] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [85.905673] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [85.905987] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [86.013746] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [86.014211] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [86.014623] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [86.015150] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [86.016158] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [86.016755] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [86.024222] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [86.119294] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [86.127201] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [86.128349] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [86.128925] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [86.128913] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [86.129929] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [86.131215] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<6> [86.131616] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [86.131757] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [86.133226] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [86.134061] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [86.134595] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [86.135136] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.135342] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [86.135841] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [86.136080] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.136089] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [86.136291] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [86.140539] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [86.140544] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<6> [86.140992] [IGT] kms_pm_rpm: exiting, ret=0
<6> [86.142270] Console: switching to colour frame buffer device 128x48
Created at 2023-12-03 11:50:18