Results for igt@kms_addfb_basic@bo-too-small

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.28-g8478eefda (x86_64) (Linux: 6.7.0-rc2-linus-v6.7-rc2-g98b1cc82c4af+ x86_64)
Out	Opened device: /dev/dri/card0 Starting subtest: bo-too-small Subtest bo-too-small: SUCCESS (0.000s)
Err	Starting subtest: bo-too-small Subtest bo-too-small: SUCCESS (0.000s)
Dmesg	<6> [189.778354] Console: switching to colour dummy device 80x25 <6> [189.778436] [IGT] kms_addfb_basic: executing <7> [190.018101] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [190.018723] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [190.018970] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [190.019347] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000) <7> [190.019563] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96] <7> [190.019761] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96] <7> [190.019852] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:96] <7> [190.024236] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.024247] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [190.024489] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [190.024671] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [190.025084] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.025341] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.025719] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.025911] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.025918] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.026144] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.027650] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.027657] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.027852] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [190.028110] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected <7> [190.029179] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] <7> [190.029196] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1] <7> [190.081519] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 <7> [190.097134] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.097144] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.097343] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [190.113123] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.113131] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [190.113336] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected <7> [190.113889] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] <7> [190.113897] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1] <7> [190.114157] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected <7> [190.114748] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] <7> [190.114756] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2] <7> [190.115133] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.115363] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [190.115727] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.115919] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.115925] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.116162] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [190.117640] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.117647] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [190.117842] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected <7> [190.118453] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] <7> [190.118461] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3] <7> [190.118816] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.119010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry <7> [190.119435] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.119628] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.119634] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.119822] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1 <7> [190.121268] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.121275] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0 <7> [190.121469] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected <7> [190.121982] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] <7> [190.121988] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2] <7> [190.122300] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected <7> [190.122998] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] <7> [190.123007] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3] <7> [190.123307] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected <7> [190.123653] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] <7> [190.123662] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor <7> [190.123669] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0 <7> [190.123736] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes : <7> [190.123740] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9 <7> [190.123761] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.123766] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [190.124037] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [190.124289] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [190.124724] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.124917] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.125327] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.125520] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.125527] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.125718] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.127188] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.127196] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.127388] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [190.127581] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected <7> [190.127792] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing <7> [190.127801] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.127807] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from disconnected to connected <7> [190.128146] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.128438] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.128890] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.129224] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.129248] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.129546] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.131504] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.131530] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.131923] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes : <7> [190.131934] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [190.131944] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [190.131954] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [190.131962] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [190.131971] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [190.132044] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.132357] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.132662] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.133161] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.133460] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.133477] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.133676] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.135141] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.135158] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.135426] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes : <7> [190.135432] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [190.135439] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [190.135444] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [190.135449] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [190.135454] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [190.135486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] <7> [190.135493] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1] <7> [190.187363] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 <7> [190.204178] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.204189] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.204387] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [190.220191] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.220200] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [190.220419] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected <7> [190.220463] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] <7> [190.220470] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1] <7> [190.220667] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected <7> [190.220689] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] <7> [190.220694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2] <7> [190.221060] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.221311] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [190.221759] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.221952] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.221958] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.222176] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [190.223610] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.223617] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [190.223811] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected <7> [190.223841] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] <7> [190.223847] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3] <7> [190.224215] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.224408] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry <7> [190.224781] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.224971] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.224976] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.225193] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1 <7> [190.226647] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.226654] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0 <7> [190.226849] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected <7> [190.226877] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] <7> [190.226883] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2] <7> [190.227088] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected <7> [190.227110] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] <7> [190.227115] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3] <7> [190.227373] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected <6> [190.227628] [IGT] kms_addfb_basic: starting subtest bo-too-small <7> [190.227701] i915 0000:00:02.0: [drm:intel_fill_fb_info [i915]] fb too big for bo (need 4198400 bytes, have 4190208 bytes) <7> [190.227918] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] could not create framebuffer <6> [190.228008] [IGT] kms_addfb_basic: finished subtest bo-too-small, SUCCESS <6> [190.228525] [IGT] kms_addfb_basic: exiting, ret=0 <7> [190.228777] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing <7> [190.228788] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.228797] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [190.229024] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [190.229294] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [190.229701] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.229893] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.230290] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.230505] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.230513] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.230706] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.232263] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.232272] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.232468] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [190.232662] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from connected to disconnected <7> [190.232676] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected <7> [190.232947] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [190.233296] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [190.233308] [drm:drm_client_modeset_probe] <7> [190.233357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] <7> [190.233368] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor <7> [190.233376] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0 <7> [190.233445] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes : <7> [190.233450] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9 <7> [190.233458] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.233464] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [190.233691] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <7> [190.233983] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [190.234483] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.234781] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.235229] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.235530] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.235541] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.235833] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.237871] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.237887] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.238269] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [190.238561] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected <7> [190.238577] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] <7> [190.238589] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1] <7> [190.289277] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 <7> [190.306239] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.306252] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.306472] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [190.322268] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.322278] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [190.322484] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected <7> [190.322494] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] <7> [190.322501] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1] <7> [190.322719] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected <7> [190.322725] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] <7> [190.322731] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2] <7> [190.323073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.323307] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [190.323714] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.323909] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.323916] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.324105] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [190.325767] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.325776] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [190.326003] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected <7> [190.326015] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] <7> [190.326026] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3] <7> [190.326564] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.326832] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry <7> [190.327217] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.327426] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.327433] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.327623] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1 <7> [190.329229] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.329241] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0 <7> [190.329442] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected <7> [190.329449] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] <7> [190.329456] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2] <7> [190.329666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected <7> [190.329672] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] <7> [190.329678] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3] <7> [190.329881] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected <7> [190.329887] [drm:drm_client_modeset_probe] connector 61 enabled? yes <7> [190.329892] [drm:drm_client_modeset_probe] connector 65 enabled? no <7> [190.329896] [drm:drm_client_modeset_probe] connector 68 enabled? no <7> [190.329900] [drm:drm_client_modeset_probe] connector 76 enabled? no <7> [190.329904] [drm:drm_client_modeset_probe] connector 81 enabled? no <7> [190.329907] [drm:drm_client_modeset_probe] connector 85 enabled? no <7> [190.329911] [drm:drm_client_modeset_probe] connector 89 enabled? no <7> [190.329914] [drm:drm_client_modeset_probe] connector 93 enabled? no <7> [190.329930] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [190.329941] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61 <7> [190.329946] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0 <7> [190.329950] [drm:drm_client_modeset_probe] found mode 1366x768 <7> [190.329954] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config <7> [190.329972] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0) <7> [190.369980] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [190.369991] [drm:drm_client_modeset_probe] <7> [190.370046] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] <7> [190.370057] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor <7> [190.370063] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0 <7> [190.370128] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes : <7> [190.370132] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9 <7> [190.370138] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] <7> [190.370143] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1 <7> [190.370421] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0 <6> [190.370705] Console: switching to colour frame buffer device 170x48 <7> [190.370706] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug <7> [190.371166] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.371411] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry <7> [190.371778] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1) <7> [190.371971] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.371978] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.372168] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1 <7> [190.373791] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga <7> [190.373799] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0 <7> [190.374014] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found] <7> [190.374231] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected <7> [190.374242] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] <7> [190.374250] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1] <7> [190.425607] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5 <7> [190.442307] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.442317] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.442521] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [190.458333] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [190.458340] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [190.458543] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected <7> [190.458552] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] <7> [190.458558] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1] <7> [190.458767] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected <7> [190.458772] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] <7> [190.458777] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2] <7> [190.459210] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.459443] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [190.459887] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [190.460087] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.460092] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.460357] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [190.461885] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [190.461892] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [190.462085] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected <7> [190.462091] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] <7> [190.462096] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3] <7> [190.462473] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.462663] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry <7> [190.463061] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1) <7> [190.463293] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.463300] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [190.463514] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1 <7> [190.465039] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd <7> [190.465045] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0 <7> [190.465239] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected <7> [190.465274] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] <7> [190.465282] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2] <7> [190.465514] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected <7> [190.465520] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] <7> [190.465525] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3] <7> [190.465727] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected <7> [190.465731] [drm:drm_client_modeset_probe] connector 61 enabled? yes <7> [190.465735] [drm:drm_client_modeset_probe] connector 65 enabled? no <7> [190.465738] [drm:drm_client_modeset_probe] connector 68 enabled? no <7> [190.465741] [drm:drm_client_modeset_probe] connector 76 enabled? no <7> [190.465743] [drm:drm_client_modeset_probe] connector 81 enabled? no <7> [190.465746] [drm:drm_client_modeset_probe] connector 85 enabled? no <7> [190.465748] [drm:drm_client_modeset_probe] connector 89 enabled? no <7> [190.465750] [drm:drm_client_modeset_probe] connector 93 enabled? no <7> [190.465769] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [190.465784] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61 <7> [190.465789] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0 <7> [190.465794] [drm:drm_client_modeset_probe] found mode 1366x768 <7> [190.465798] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config <7> [190.465826] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)

Created at 2023-11-20 01:42:31