Results for igt@kms_force_connector_basic@force-connector-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.28-g5e82a8ee4 (x86_64) (Linux: 6.6.0-linus-v6.6-gffc253263a13+ x86_64)
Out	Opened device: /dev/dri/card0 Starting subtest: force-connector-state Subtest force-connector-state: SUCCESS (0.731s)
Err	Starting subtest: force-connector-state Subtest force-connector-state: SUCCESS (0.731s)
Dmesg	<6> [103.417190] [IGT] kms_force_connector_basic: executing <7> [103.420323] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [103.421397] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [103.421807] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [103.423336] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 0 or reprobing <7> [103.423385] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.423431] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.423917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.476354] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.496203] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.496216] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.496474] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.513545] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.513553] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.513739] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.514010] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [103.514078] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.514085] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.514316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.565348] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.583065] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.583081] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.583451] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.603531] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.603540] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.603760] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.604011] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [103.604070] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.604078] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.604347] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.656350] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.675672] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.675687] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.676000] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.695866] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.695877] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.696236] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.696609] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <6> [103.696749] [IGT] kms_force_connector_basic: starting subtest force-connector-state <7> [103.703324] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [103.703334] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [103.703569] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.704091] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [103.704613] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [103.705281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [103.706214] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [103.706439] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [103.707358] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.708992] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.710574] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.712164] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.713923] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.715670] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.717441] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.719169] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.720933] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.721855] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [103.722795] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [103.723472] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [103.724024] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [103.724426] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [103.724762] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [103.725088] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [103.725893] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.726254] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [103.727438] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [103.727450] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [103.727769] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.728432] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.728772] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [103.729936] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.729947] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.730276] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.781352] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.799610] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.799625] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.799913] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.819186] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.819197] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.819520] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.819859] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [103.820769] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [103.820781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [103.821097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.821771] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [103.822411] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [103.823065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [103.823992] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [103.824229] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [103.825162] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.826774] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.828359] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.829966] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.831723] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.833475] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.835173] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.836902] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.838498] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.839482] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [103.840319] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [103.841007] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [103.841544] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [103.841774] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [103.841967] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [103.842180] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [103.842924] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.843218] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [103.843265] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [103.843274] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [103.843484] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.844000] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.844340] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [103.844379] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.844389] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.844598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.896351] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.915687] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.915704] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.916031] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.935933] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.935944] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.936300] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.936672] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [103.938021] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.938394] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [103.938966] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [103.940357] [drm:drm_mode_setcrtc] [CRTC:51:pipe A] <7> [103.942624] [drm:drm_mode_setcrtc] [CRTC:72:pipe B] <7> [103.944354] [drm:drm_mode_setcrtc] [CRTC:93:pipe C] <7> [103.946717] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 2 or reprobing <7> [103.946726] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.946735] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.964566] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [103.964850] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [103.965090] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [103.998358] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.018246] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.018277] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.018593] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.037866] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.037884] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.038103] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.038391] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] status updated from disconnected to connected <7> [104.039018] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] probed modes : <7> [104.039028] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [104.039037] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [104.039045] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [104.039052] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [104.039059] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [104.039171] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.039183] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.039482] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.040229] [drm:drm_client_modeset_probe] <7> [104.091346] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.108984] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.109009] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.109305] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.125956] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.125971] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.126179] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.126658] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] probed modes : <7> [104.126680] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa <7> [104.126691] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5 <7> [104.126700] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5 <7> [104.126708] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5 <7> [104.126716] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa <7> [104.127161] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 2 to 1 or reprobing <7> [104.127171] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.127181] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.127484] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] status updated from connected to disconnected <7> [104.127506] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.127625] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.127634] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.127927] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.128231] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 1 to 0 or reprobing <7> [104.128241] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.128251] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.128565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.180351] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.199106] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.199120] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.199427] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.218290] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.218298] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.218477] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.218680] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.218961] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [104.218970] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [104.219203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.219871] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [104.220526] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [104.221205] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [104.222412] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [104.222749] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [104.223853] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.225522] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.227171] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.228784] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.230589] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.232376] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.234172] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.235989] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.237583] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.238364] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [104.239401] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [104.240065] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [104.240625] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [104.241005] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [104.241366] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [104.241690] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [104.242491] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.242833] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [104.242850] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [104.242861] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [104.243207] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.243863] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.244241] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [104.244253] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.244264] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.244572] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.296353] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.316193] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.316212] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.316510] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.336819] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.336827] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.337003] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.337242] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.337255] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [104.337263] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [104.337270] [drm:drm_client_modeset_probe] connector 108 enabled? no <7> [104.337277] [drm:drm_client_modeset_probe] connector 114 enabled? no <7> [104.337306] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [104.337322] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [104.337668] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7> [104.337675] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <6> [104.337685] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [104.337802] [drm:drm_client_modeset_probe] <7> [104.337687] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.337996] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.389366] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.408208] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.408224] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.408536] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.426764] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.426774] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.426992] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.427289] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.427380] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <6> [104.427535] [IGT] kms_force_connector_basic: finished subtest force-connector-state, SUCCESS <7> [104.427399] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [104.427800] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [104.427810] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.428653] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [104.429248] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [104.429858] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [104.430792] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [104.431027] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [104.432028] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.433667] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.435172] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.436558] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.438173] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.439950] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.441776] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.443513] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.445181] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.446098] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [104.447000] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [104.447696] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [104.448186] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [104.448445] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [104.448642] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [104.448831] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [104.449582] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.449904] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [104.449919] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [104.449928] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [104.450113] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.450658] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.450886] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [104.450894] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.450901] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.451078] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.502358] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.522803] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.522820] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.523175] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.542100] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.542109] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.542346] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.542624] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.542634] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [104.542641] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [104.542645] [drm:drm_client_modeset_probe] connector 108 enabled? no <7> [104.542650] [drm:drm_client_modeset_probe] connector 114 enabled? no <7> [104.542690] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [104.542701] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [104.542739] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [104.542755] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [104.542972] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:DP-1] EDID override reset <7> [104.543033] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [104.543044] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [104.543431] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.544150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [104.544794] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [104.545463] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [104.546438] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [104.546760] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [104.547535] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.549174] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.550856] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.552517] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.554326] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.556181] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.557946] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.559716] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.561363] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [104.562239] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [104.563112] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [104.563835] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [104.564323] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [104.564651] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [104.564848] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [104.565034] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [104.565704] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.566025] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [104.566275] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:108:DP-2] EDID override reset <7> [104.566306] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [104.566313] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [104.566517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.567029] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.567363] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [104.567615] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 0 or reprobing <7> [104.567622] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.567630] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.567833] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.619368] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.639893] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.639913] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.640448] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.660580] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.660590] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.660809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.661055] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.661164] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.661177] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.661515] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.713353] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.732189] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.732205] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.732517] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.750686] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.750695] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.750889] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.751108] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.751368] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:114:HDMI-A-1] EDID override reset <7> [104.751411] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.751421] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.751646] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.803353] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.822187] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.822202] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.822515] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.840688] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.840697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.840890] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.841109] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <6> [104.841757] [IGT] kms_force_connector_basic: exiting, ret=0 <7> [104.842071] [drm:status_store] [CONNECTOR:114:HDMI-A-1] force updated from 0 to 0 or reprobing <7> [104.842079] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [104.842088] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [104.842355] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.894365] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [104.914275] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.914292] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [104.914618] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [104.933407] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [104.933417] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [104.933637] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.933890] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [104.934357] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-10-31 09:59:03