Results for igt@kms_frontbuffer_tracking@basic

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g5e82a8ee4 (x86_64) (Linux: 6.6.0-linus-v6.6-gffc253263a13+ x86_64)
Out 
Opened device: /dev/dri/card0
FBC last action not supported
Can't test DRRS: no usable screen.
Starting subtest: basic
Subtest basic: SUCCESS (3.338s)
Err 
Starting subtest: basic
Subtest basic: SUCCESS (3.338s)
Dmesg
<6> [170.705775] Console: switching to colour dummy device 80x25
<6> [170.706225] [IGT] kms_frontbuffer_tracking: executing
<7> [170.709929] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [170.711273] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [170.711764] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [170.729499] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [170.729520] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [170.729943] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [170.730975] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [170.730988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [170.731344] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [170.732369] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [170.732381] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [170.732758] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [170.734165] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [170.734180] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [170.735096] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [170.735406] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [170.735737] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [170.736029] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [170.736355] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [170.736367] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [170.736374] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [170.736406] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [170.736727] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [170.737796] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [170.738087] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [170.739111] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [170.739124] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [170.739135] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [170.739188] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [170.739199] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [170.739523] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [170.739563] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [170.739573] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [170.739923] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [170.739964] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [170.739974] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [170.740307] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [170.743633] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:269]
<7> [170.743777] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:270]
<7> [170.743982] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:271]
<7> [170.744182] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:272]
<7> [170.744381] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:273]
<6> [170.746417] [IGT] kms_frontbuffer_tracking: starting subtest basic
<7> [170.746572] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [170.752236] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:269]
<7> [170.752376] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:270]
<7> [170.752580] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:271]
<7> [170.752858] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:272]
<7> [170.753075] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:273]
<7> [170.754136] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:274]
<7> [170.847403] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [170.847579] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1]
<7> [170.897973] [drm:drm_mode_setcrtc] [CRTC:167:pipe B]
<7> [170.906564] [drm:drm_mode_setcrtc] [CRTC:236:pipe C]
<7> [170.950003] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [170.951263] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [171.033033] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:274] from all active usage due to RMFB ioctl
<7> [171.033221] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:274] is removed
<7> [171.033421] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0
<7> [171.034233] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [171.035002] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [171.035741] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [171.036432] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [171.037205] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0
<7> [171.037980] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0
<7> [171.038752] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0
<7> [171.039478] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0
<7> [171.046855] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [171.064973] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:266]
<7> [171.065528] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:274]
<7> [171.066100] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:277]
<7> [171.066638] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:278]
<7> [171.882284] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [171.882459] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1]
<7> [171.882855] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985
<7> [171.883676] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [171.884383] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [171.885117] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0
<7> [171.885842] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0
<7> [171.886527] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1
<7> [171.887277] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446
<7> [171.887965] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446
<7> [171.888264] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446
<7> [171.891845] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1
<7> [171.892162] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [171.908877] [drm:drm_mode_setcrtc] [CRTC:167:pipe B]
<7> [171.917108] [drm:drm_mode_setcrtc] [CRTC:236:pipe C]
<7> [171.951050] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [171.952047] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.031722] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [172.031902] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1]
<7> [172.049146] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.132239] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [172.132431] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1]
<7> [172.149229] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.232291] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [172.232468] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1]
<7> [172.249538] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.334722] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:278] from all active usage due to RMFB ioctl
<7> [172.334914] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:278] is removed
<7> [172.335112] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0
<7> [172.335932] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [172.336723] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [172.337456] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [172.338211] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [172.339002] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0
<7> [172.339794] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0
<7> [172.340551] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0
<7> [172.341330] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0
<7> [172.348237] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [172.432829] [drm:drm_mode_setcrtc] [CRTC:98:pipe A]
<7> [172.433008] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1]
<7> [172.433326] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985
<7> [172.434146] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [172.434910] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [172.435655] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0
<7> [172.436351] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0
<7> [172.437085] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1
<7> [172.437870] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446
<7> [172.438787] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446
<7> [172.439510] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446
<7> [172.446266] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1
<7> [172.446913] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [172.458075] [drm:drm_mode_setcrtc] [CRTC:167:pipe B]
<7> [172.466244] [drm:drm_mode_setcrtc] [CRTC:236:pipe C]
<7> [172.501655] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.502661] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [172.503708] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.582772] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.666684] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:274]
<7> [172.673359] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [172.674402] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.749717] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.837238] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [172.838284] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [172.916461] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.003466] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [173.022249] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.100067] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.285927] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [173.286387] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.367023] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.500147] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [173.501270] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.583556] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.678995] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [173.687108] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.766029] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [173.766973] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067
<7> [173.767267] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.808044] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [173.808939] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [173.809732] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [173.834058] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [173.834912] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [173.835766] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [173.836538] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [173.837316] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [173.838108] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [173.838877] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [173.839652] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [173.866490] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [173.868282] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [173.868727] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [173.869062] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [173.879439] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [173.880203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [173.880586] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [173.881009] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [173.881391] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [173.881823] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [173.882200] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [173.882551] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [173.882927] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [173.967540] i915 0000:00:02.0: [drm:i915_fifo_underrun_reset_write [i915]] Re-arming FIFO underruns on pipe A
<7> [174.001783] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [174.002582] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [174.003391] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [174.034297] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [174.035157] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [174.036007] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [174.036813] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [174.037557] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [174.038343] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [174.039112] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [174.039865] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [174.050458] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:274] from all active usage due to RMFB ioctl
<7> [174.050743] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:274] is removed
<7> [174.050995] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0
<7> [174.051820] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [174.052514] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [174.053440] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [174.054205] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [174.054948] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0
<7> [174.055717] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0
<7> [174.056340] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0
<7> [174.056970] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0
<7> [174.066966] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<6> [174.085164] [IGT] kms_frontbuffer_tracking: finished subtest basic, SUCCESS
<6> [174.087519] [IGT] kms_frontbuffer_tracking: exiting, ret=0
<7> [174.089104] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [174.101749] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [174.102212] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [174.102522] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [174.132968] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985
<7> [174.133768] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [174.134465] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [174.135227] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0
<7> [174.136672] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0
<7> [174.137389] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1
<7> [174.138181] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446
<7> [174.138977] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446
<7> [174.139926] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446
<7> [174.141327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [174.142187] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [174.143089] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [174.143908] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [174.144686] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [174.145436] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [174.146289] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [174.147211] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [174.148041] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1
<7> [174.148773] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<6> [174.167744] Console: switching to colour frame buffer device 400x112
<7> [174.201701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [174.202105] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [174.202414] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
Created at 2023-10-31 09:59:03