igt@i915_module_load@load on fi-kbl-x1275@linus-v6.6-rc6 Test details

Detail	Value
Igt-Version	IGT-Version: 1.28-g08e87a32f (x86_64) (Linux: 6.6.0-rc6-linus-v6.6-rc6-g58720809f527+ x86_64)
Out	Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (1.352s)
Err	Starting subtest: load Subtest load: SUCCESS (1.352s)
Dmesg	<6> [47.743410] [IGT] i915_module_load: executing <6> [47.757860] [IGT] i915_module_load: starting subtest load <4> [48.273358] <4> [48.273366] ******************************************************** <4> [48.273367] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [48.273368] <4> [48.273370] trace_printk() being used. Allocating extra memory. <4> [48.273371] <4> [48.273372] This means that this is a DEBUG kernel and it is <4> [48.273373] unsafe for production use. <4> [48.273374] <4> [48.273376] If you see this message and you are not debugging <4> [48.273377] the kernel, report this immediately to your vendor! <4> [48.273378] <4> [48.273379] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [48.273380] ****************************************************** <7> [48.314549] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K <7> [48.314739] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no) <7> [48.314898] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH <7> [48.315066] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [48.315353] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [48.315522] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz <7> [48.316448] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [48.316624] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [48.316828] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 32M <6> [48.316939] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [48.317281] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [48.317690] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [48.317706] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 8c700047 <7> [48.317848] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 32768K, usable: 31744K <7> [48.318144] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x71f90018 <7> [48.318308] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [48.318449] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [48.318649] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [48.318868] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [48.322222] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [48.322400] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [48.322582] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [48.322752] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [48.322950] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [48.323057] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [48.323160] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [48.323259] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no <7> [48.323359] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [48.323458] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [48.323611] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no <7> [48.323725] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [48.323822] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [48.323919] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [48.324436] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [48.324636] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 196 <7> [48.324796] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [48.324953] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [48.325109] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [48.325263] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [48.325419] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 280, min size 812) <7> [48.325612] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 24, min size 34) <7> [48.325793] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [48.325950] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [48.326105] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [48.326295] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78) <7> [48.326448] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7> [48.326683] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [48.326846] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x78c6 <7> [48.326998] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [48.327149] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [48.327301] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [48.327448] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [48.327635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [48.327814] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [48.327963] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 3 <7> [48.328131] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [48.328281] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 3 <7> [48.328430] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [48.328640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [48.328837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [48.329001] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [48.329152] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [48.329443] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [48.329659] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [48.329842] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [48.330041] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [48.330191] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [48.330339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [48.330541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [48.330702] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [48.330757] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [48.330911] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [48.331061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [48.331240] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [48.331485] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin <7> [48.332475] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [48.333023] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [48.333205] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [48.333350] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [48.333518] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [48.333695] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [48.333834] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [48.333994] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [48.334133] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [48.334271] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [48.334431] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <6> [48.336328] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) <7> [48.336249] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [48.337714] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [48.337968] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT) <7> [48.338134] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A] <7> [48.342544] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0) <7> [48.342710] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [48.342908] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [48.343136] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static <7> [48.343348] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [48.343603] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [48.343792] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002 <7> [48.343941] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [48.344090] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [48.344240] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255, controller 0 <7> [48.344388] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1 <7> [48.344625] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0 <7> [48.344844] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 0 t8 0 t9 0 t10 0 t11_t12 0 <7> [48.344980] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [48.345115] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [48.345249] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [48.345381] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [48.345668] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06 <7> [48.346012] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on <7> [48.346172] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [48.346385] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000 <7> [48.346583] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [48.346777] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008 <7> [48.346944] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled <7> [48.561501] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.572499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.583501] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.594500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.605500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.616500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.627500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.638499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.649504] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.660499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.671502] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.682501] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.693499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.704500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.715498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.726498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.737498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.748500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.759502] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.770498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.781498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.792500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.803499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.814498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.825498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.836500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.847498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.858498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.869498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.880498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.891498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.902498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f) <7> [48.902683] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110 <6> [48.902717] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] failed to retrieve link info, disabling eDP <7> [48.902767] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD off <7> [48.902967] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000 <7> [48.903156] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] Using AUX CH B (VBT) <7> [48.903305] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:94:DDI B/PHY B] <7> [48.903701] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [48.903900] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:106:DDI C/PHY C] Using AUX CH C (VBT) <7> [48.904071] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:106:DDI C/PHY C] <7> [48.904332] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [48.904478] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:106:DDI C/PHY C] <7> [48.904651] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:106:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [48.905094] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [48.905268] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [48.905431] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [48.905616] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [48.905795] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A <7> [48.905944] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [48.906091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B <7> [48.906239] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B <7> [48.906386] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [48.906570] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C <7> [48.906756] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C <7> [48.906906] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [48.907084] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A <7> [48.907261] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:96:DP-MST A] hw state readout: disabled, pipe A <7> [48.907428] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:97:DP-MST B] hw state readout: disabled, pipe B <7> [48.907609] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DP-MST C] hw state readout: disabled, pipe C <7> [48.907787] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DDI C/PHY C] hw state readout: disabled, pipe A <7> [48.907931] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DP-MST A] hw state readout: disabled, pipe A <7> [48.908072] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:109:DP-MST B] hw state readout: disabled, pipe B <7> [48.908215] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DP-MST C] hw state readout: disabled, pipe C <7> [48.908364] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [48.908558] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [48.908740] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [48.908893] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [48.909098] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:DP-1] hw state readout: disabled <7> [48.909260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:107:DP-2] hw state readout: disabled <7> [48.909413] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:113:HDMI-A-1] hw state readout: disabled <7> [48.909620] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [48.909792] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz <7> [48.909933] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [48.910076] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [48.910254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz <7> [48.910404] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz <7> [48.910587] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [48.910773] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [48.910938] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz <7> [48.911098] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz <7> [48.911241] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [48.911381] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [48.911594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [48.911774] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [48.911924] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [48.912073] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [48.912224] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [48.912368] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [48.912548] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [48.912989] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [48.913108] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000] <7> [48.913233] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [48.913377] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global <7> [48.914656] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0 <7> [48.914808] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0 <7> [48.914949] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0 <7> [48.925053] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [48.925194] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [48.925315] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [48.925433] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [48.926130] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <7> [48.926311] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping <7> [48.926454] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping <7> [48.926636] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping <7> [48.926803] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [48.926958] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [48.931336] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1 <7> [48.932329] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:DP-1] generating connector hotplug event <7> [48.932907] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2 <7> [48.933481] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:107:DP-2] generating connector hotplug event <7> [48.933936] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:113:HDMI-A-1] generating connector hotplug event <6> [48.933985] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [48.935566] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <6> [48.952372] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [48.957578] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4 <7> [48.959394] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [48.960230] [drm:drm_client_modeset_probe] <7> [48.960187] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [48.960482] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [48.960415] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [48.960525] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [48.960669] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [48.960843] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [48.961111] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [48.961411] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [48.961485] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [48.961787] i915 device info: pciid=0x591d rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9 <7> [48.961790] i915 device info: graphics version: 9 <7> [48.961792] i915 device info: media version: 9 <7> [48.961794] i915 device info: graphics stepping: F0 <7> [48.961795] i915 device info: media stepping: F0 <7> [48.961797] i915 device info: display stepping: C0 <7> [48.961798] i915 device info: base die stepping: <7> [48.961799] i915 device info: gt: 2 <7> [48.961801] i915 device info: memory-regions: 0x21 <7> [48.961802] i915 device info: page-sizes: 0x11000 <7> [48.961804] i915 device info: platform: KABYLAKE <7> [48.961805] i915 device info: ppgtt-size: 48 <7> [48.961807] i915 device info: ppgtt-type: 2 <7> [48.961808] i915 device info: dma_mask_size: 39 <7> [48.961810] i915 device info: is_mobile: no <7> [48.961811] i915 device info: is_lp: no <7> [48.961813] i915 device info: require_force_probe: no <7> [48.961814] i915 device info: is_dgfx: no <7> [48.961815] i915 device info: has_64bit_reloc: yes <7> [48.961817] i915 device info: has_64k_pages: no <7> [48.961818] i915 device info: gpu_reset_clobbers_display: no <7> [48.961820] i915 device info: has_reset_engine: yes <7> [48.961821] i915 device info: has_3d_pipeline: yes <7> [48.961822] i915 device info: has_4tile: no <7> [48.961824] i915 device info: has_flat_ccs: no <7> [48.961825] i915 device info: has_global_mocs: no <7> [48.961826] i915 device info: has_gmd_id: no <7> [48.961828] i915 device info: has_gt_uc: yes <7> [48.961829] i915 device info: has_heci_pxp: no <7> [48.961831] i915 device info: has_heci_gscfi: no <7> [48.961832] i915 device info: has_guc_deprivilege: no <7> [48.961833] i915 device info: has_l3_ccs_read: no <7> [48.961835] i915 device info: has_l3_dpf: no <7> [48.961836] i915 device info: has_llc: yes <7> [48.961837] i915 device info: has_logical_ring_contexts: yes <7> [48.961730] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [48.961839] i915 device info: has_logical_ring_elsq: no <7> [48.961840] i915 device info: has_media_ratio_mode: no <7> [48.961841] i915 device info: has_mslice_steering: no <7> [48.961842] i915 device info: has_oa_bpc_reporting: no <7> [48.961843] i915 device info: has_oa_slice_contrib_limits: no <7> [48.961845] i915 device info: has_oam: no <7> [48.961846] i915 device info: has_one_eu_per_fuse_bit: no <7> [48.961847] i915 device info: has_pxp: no <7> [48.961848] i915 device info: has_rc6: yes <7> [48.961849] i915 device info: has_rc6p: no <7> [48.961850] i915 device info: has_rps: yes <7> [48.961851] i915 device info: has_runtime_pm: yes <7> [48.961853] i915 device info: has_snoop: no <7> [48.961854] i915 device info: has_coherent_ggtt: yes <7> [48.961855] i915 device info: tuning_thread_rr_after_dep: no <7> [48.961856] i915 device info: unfenced_needs_alignment: no <7> [48.961857] i915 device info: hws_needs_physical: no <7> [48.961858] i915 device info: has_pooled_eu: no <7> [48.961859] i915 device info: rawclk rate: 24000 kHz <7> [48.961861] i915 device info: display version: 9 <7> [48.961862] i915 device info: cursor_needs_physical: no <7> [48.961863] i915 device info: has_cdclk_crawl: no <7> [48.961864] i915 device info: has_cdclk_squash: no <7> [48.961866] i915 device info: has_ddi: yes <7> [48.961867] i915 device info: has_dp_mst: yes <7> [48.961868] i915 device info: has_dsb: no <7> [48.961869] i915 device info: has_fpga_dbg: yes <7> [48.961870] i915 device info: has_gmch: no <7> [48.961871] i915 device info: has_hotplug: yes <7> [48.961872] i915 device info: has_hti: no <7> [48.961873] i915 device info: has_ipc: yes <7> [48.961875] i915 device info: has_overlay: no <7> [48.961876] i915 device info: has_psr: yes <7> [48.961877] i915 device info: has_psr_hw_tracking: yes <7> [48.961878] i915 device info: overlay_needs_physical: no <7> [48.961879] i915 device info: supports_tv: no <7> [48.961880] i915 device info: has_hdcp: yes <7> [48.961881] i915 device info: has_dmc: yes <7> [48.961882] i915 device info: has_dsc: no <7> [48.961884] i915 device info: iommu: enabled <7> [48.961885] i915 device info: available engines: 40403 <7> [48.961887] i915 device info: slice total: 1, mask=0001 <7> [48.961888] i915 device info: subslice total: 3 <7> [48.961889] i915 device info: slice0: 3 subslices, mask=00000007 <7> [48.961891] i915 device info: slice1: 0 subslices, mask=00000000 <7> [48.961892] i915 device info: slice2: 0 subslices, mask=00000000 <7> [48.961893] i915 device info: EU total: 24 <7> [48.961895] i915 device info: EU per subslice: 8 <7> [48.961896] i915 device info: has slice power gating: no <7> [48.961897] i915 device info: has subslice power gating: no <7> [48.961898] i915 device info: has EU power gating: yes <6> [48.961900] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [48.961901] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [48.961902] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [48.961986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [48.962682] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [48.963218] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] status updated from unknown to disconnected <7> [48.963441] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [48.963451] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] <7> [48.963459] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [48.963746] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [48.964335] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [48.964941] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [48.965512] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [48.966854] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [48.967821] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [48.968603] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [48.968797] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [48.968957] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [48.969114] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [48.969777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [48.969967] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] status updated from unknown to disconnected <7> [48.969979] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected <7> [48.969993] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] <7> [48.969999] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [48.970152] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [48.972084] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [48.972279] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [48.973010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [48.974040] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [48.974045] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [48.974194] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [49.005359] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [49.005367] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [49.005599] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.005876] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] status updated from unknown to disconnected <7> [49.005889] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected <7> [49.005900] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [49.005928] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [49.005932] [drm:drm_client_modeset_probe] connector 107 enabled? no <7> [49.005947] [drm:drm_client_modeset_probe] connector 113 enabled? no <7> [49.006090] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [49.006110] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [49.006128] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [49.006154] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [49.006909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.007074] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [49.007594] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [49.008414] [drm:drm_client_modeset_probe] <7> [49.008599] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [49.008614] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [49.008858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [49.009049] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [49.009225] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [49.009925] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.010272] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [49.010280] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] <7> [49.010287] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [49.010549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.011033] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [49.011561] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [49.012114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [49.013528] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [49.014535] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [49.015231] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [49.015550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [49.015744] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [49.015933] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [49.016587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.016822] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected <7> [49.016832] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] <7> [49.016840] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [49.017017] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.018599] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [49.018774] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [49.019559] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [49.020109] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [49.020116] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [49.020283] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [49.048780] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [49.048788] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [49.048926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.049065] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected <7> [49.049071] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [49.049080] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [49.049083] [drm:drm_client_modeset_probe] connector 107 enabled? no <7> [49.049086] [drm:drm_client_modeset_probe] connector 113 enabled? no <7> [49.049199] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [49.049216] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [49.049232] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [49.049241] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [49.049318] [drm:drm_client_modeset_probe] <7> [49.049342] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [49.049347] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [49.049471] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.049993] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.050137] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [49.050142] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] <7> [49.050147] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [49.050271] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.050733] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [49.051254] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [49.051861] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [49.053191] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [49.054228] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [49.054871] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [49.055032] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [49.055168] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [49.055300] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [49.055907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.056061] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected <7> [49.056067] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] <7> [49.056073] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [49.056197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.057244] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [49.057371] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [49.058041] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [49.058553] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [49.058560] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [49.058688] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [49.084946] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [49.084956] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [49.085098] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [49.085249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected <7> [49.085256] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [49.085262] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [49.085267] [drm:drm_client_modeset_probe] connector 107 enabled? no <7> [49.085272] [drm:drm_client_modeset_probe] connector 113 enabled? no <7> [49.085306] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [49.085319] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [49.085338] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [49.085345] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [49.097156] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [49.097954] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [49.098394] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [49.100895] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [49.101033] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [49.101514] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <6> [49.110435] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [49.110691] [IGT] i915_module_load: exiting, ret=0

<6> [47.743410] [IGT] i915_module_load: executing

<6> [47.757860] [IGT] i915_module_load: starting subtest load

<4> [48.273366] **********************************************************

<4> [48.273367] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [48.273370] ** trace_printk() being used. Allocating extra memory. **

<4> [48.273372] ** This means that this is a DEBUG kernel and it is **

<4> [48.273373] ** unsafe for production use. **

<4> [48.273376] ** If you see this message and you are not debugging **

<4> [48.273377] ** the kernel, report this immediately to your vendor! **

<4> [48.273379] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [48.273380] **********************************************************

<7> [48.314549] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K

<7> [48.314739] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)

<7> [48.314898] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH

<7> [48.315066] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [48.315353] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [48.315522] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz

<7> [48.316448] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [48.316624] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [48.316828] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 32M

<6> [48.316939] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [48.317281] i915 0000:00:02.0: vgaarb: deactivate vga console

<6> [48.317690] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [48.317706] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 8c700047

<7> [48.317848] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 32768K, usable: 31744K

<7> [48.318144] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x71f90018

<7> [48.318308] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0

<7> [48.318449] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [48.318649] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [48.318868] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [48.322222] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483

<7> [48.322400] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [48.322582] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [48.322752] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [48.322950] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [48.323057] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [48.323160] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [48.323259] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no

<7> [48.323359] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [48.323458] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [48.323611] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no

<7> [48.323725] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [48.323822] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [48.323919] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [48.324436] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [48.324636] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 196

<7> [48.324796] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [48.324953] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)

<7> [48.325109] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [48.325263] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [48.325419] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 280, min size 812)

<7> [48.325612] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 24, min size 34)

<7> [48.325793] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [48.325950] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)

<7> [48.326105] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [48.326295] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)

<7> [48.326448] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0

<7> [48.326683] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [48.326846] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x78c6

<7> [48.326998] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [48.327149] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6

<7> [48.327301] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [48.327448] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [48.327635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [48.327814] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [48.327963] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 3

<7> [48.328131] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [48.328281] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 3

<7> [48.328430] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02

<7> [48.328640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [48.328837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [48.329001] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO

<7> [48.329152] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [48.329443] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz

<7> [48.329659] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz

<7> [48.329842] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [48.330041] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [48.330191] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [48.330339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [48.330541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<6> [48.330702] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem

<7> [48.330757] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [48.330911] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [48.331061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [48.331240] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [48.331485] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin

<7> [48.332475] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [48.333023] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV

<7> [48.333205] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us

<7> [48.333350] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [48.333518] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [48.333695] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [48.333834] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [48.333994] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [48.334133] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [48.334271] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [48.334431] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<6> [48.336328] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)

<7> [48.336249] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [48.337714] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0

<7> [48.337968] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT)

<7> [48.338134] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]

<7> [48.342544] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)

<7> [48.342710] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [48.342908] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [48.343136] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static

<7> [48.343348] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [48.343603] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300

<7> [48.343792] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002

<7> [48.343941] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName

<7> [48.344090] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [48.344240] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255, controller 0

<7> [48.344388] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1

<7> [48.344625] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0

<7> [48.344844] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 0 t8 0 t9 0 t10 0 t11_t12 0

<7> [48.344980] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [48.345115] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [48.345249] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [48.345381] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [48.345668] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06

<7> [48.346012] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on

<7> [48.346172] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [48.346385] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000

<7> [48.346583] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [48.346777] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008

<7> [48.346944] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled

<7> [48.561501] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.572499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.583501] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.594500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.605500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.616500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.627500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.638499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.649504] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.660499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.671502] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.682501] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.693499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.704500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.715498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.726498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.737498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.748500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.759502] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.770498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.781498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.792500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.803499] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.814498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.825498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.836500] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.847498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.858498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.869498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.880498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.891498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.902498] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)

<7> [48.902683] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110

<6> [48.902717] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] failed to retrieve link info, disabling eDP

<7> [48.902767] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD off

<7> [48.902967] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000

<7> [48.903156] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] Using AUX CH B (VBT)

<7> [48.903305] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:94:DDI B/PHY B]

<7> [48.903701] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [48.903900] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:106:DDI C/PHY C] Using AUX CH C (VBT)

<7> [48.904071] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:106:DDI C/PHY C]

<7> [48.904332] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [48.904478] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:106:DDI C/PHY C]

<7> [48.904651] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:106:DDI C/PHY C] Using DDC pin 0x4 (VBT)

<7> [48.905094] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled

<7> [48.905268] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled

<7> [48.905431] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled

<7> [48.905616] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [48.905795] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A

<7> [48.905944] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A

<7> [48.906091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B

<7> [48.906239] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B

<7> [48.906386] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B

<7> [48.906570] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C

<7> [48.906756] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C

<7> [48.906906] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C

<7> [48.907084] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [48.907261] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:96:DP-MST A] hw state readout: disabled, pipe A

<7> [48.907428] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:97:DP-MST B] hw state readout: disabled, pipe B

<7> [48.907609] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DP-MST C] hw state readout: disabled, pipe C

<7> [48.907787] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DDI C/PHY C] hw state readout: disabled, pipe A

<7> [48.907931] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DP-MST A] hw state readout: disabled, pipe A

<7> [48.908072] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:109:DP-MST B] hw state readout: disabled, pipe B

<7> [48.908215] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DP-MST C] hw state readout: disabled, pipe C

<7> [48.908364] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1

<7> [48.908558] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [48.908740] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [48.908893] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [48.909098] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:DP-1] hw state readout: disabled

<7> [48.909260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:107:DP-2] hw state readout: disabled

<7> [48.909413] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:113:HDMI-A-1] hw state readout: disabled

<7> [48.909620] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [48.909792] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz

<7> [48.909933] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz

<7> [48.910076] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [48.910254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz

<7> [48.910404] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz

<7> [48.910587] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz

<7> [48.910773] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [48.910938] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz

<7> [48.911098] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz

<7> [48.911241] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz

<7> [48.911381] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [48.911594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]

<7> [48.911774] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]

<7> [48.911924] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]

<7> [48.912073] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling

<7> [48.912224] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [48.912368] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [48.912548] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [48.912989] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [48.913108] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]

<7> [48.913233] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0

<7> [48.913377] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global

<7> [48.914656] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0

<7> [48.914808] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0

<7> [48.914949] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0

<7> [48.925053] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [48.925194] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [48.925315] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [48.925433] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [48.926130] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV

<7> [48.926311] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping

<7> [48.926454] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping

<7> [48.926636] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping

<7> [48.926803] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [48.926958] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [48.931336] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1

<7> [48.932329] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:DP-1] generating connector hotplug event

<7> [48.932907] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2

<7> [48.933481] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:107:DP-2] generating connector hotplug event

<7> [48.933936] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:113:HDMI-A-1] generating connector hotplug event

<6> [48.933985] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [48.935566] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected

<6> [48.952372] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [48.957578] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4

<7> [48.959394] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)

<7> [48.960230] [drm:drm_client_modeset_probe]

<7> [48.960187] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D

<7> [48.960482] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]

<7> [48.960415] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C

<7> [48.960525] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]

<7> [48.960669] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B

<7> [48.960843] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E

<7> [48.961111] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [48.961411] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [48.961485] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [48.961787] i915 device info: pciid=0x591d rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9

<7> [48.961790] i915 device info: graphics version: 9

<7> [48.961792] i915 device info: media version: 9

<7> [48.961794] i915 device info: graphics stepping: F0

<7> [48.961795] i915 device info: media stepping: F0

<7> [48.961797] i915 device info: display stepping: C0

<7> [48.961798] i915 device info: base die stepping: **

<7> [48.961801] i915 device info: memory-regions: 0x21

<7> [48.961802] i915 device info: page-sizes: 0x11000

<7> [48.961804] i915 device info: platform: KABYLAKE

<7> [48.961805] i915 device info: ppgtt-size: 48

<7> [48.961807] i915 device info: ppgtt-type: 2

<7> [48.961808] i915 device info: dma_mask_size: 39

<7> [48.961810] i915 device info: is_mobile: no

<7> [48.961811] i915 device info: is_lp: no

<7> [48.961813] i915 device info: require_force_probe: no

<7> [48.961814] i915 device info: is_dgfx: no

<7> [48.961815] i915 device info: has_64bit_reloc: yes

<7> [48.961817] i915 device info: has_64k_pages: no

<7> [48.961818] i915 device info: gpu_reset_clobbers_display: no

<7> [48.961820] i915 device info: has_reset_engine: yes

<7> [48.961821] i915 device info: has_3d_pipeline: yes

<7> [48.961822] i915 device info: has_4tile: no

<7> [48.961824] i915 device info: has_flat_ccs: no

<7> [48.961825] i915 device info: has_global_mocs: no

<7> [48.961826] i915 device info: has_gmd_id: no

<7> [48.961828] i915 device info: has_gt_uc: yes

<7> [48.961829] i915 device info: has_heci_pxp: no

<7> [48.961831] i915 device info: has_heci_gscfi: no

<7> [48.961832] i915 device info: has_guc_deprivilege: no

<7> [48.961833] i915 device info: has_l3_ccs_read: no

<7> [48.961835] i915 device info: has_l3_dpf: no

<7> [48.961836] i915 device info: has_llc: yes

<7> [48.961837] i915 device info: has_logical_ring_contexts: yes

<7> [48.961730] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [48.961839] i915 device info: has_logical_ring_elsq: no

<7> [48.961840] i915 device info: has_media_ratio_mode: no

<7> [48.961841] i915 device info: has_mslice_steering: no

<7> [48.961842] i915 device info: has_oa_bpc_reporting: no

<7> [48.961843] i915 device info: has_oa_slice_contrib_limits: no

<7> [48.961845] i915 device info: has_oam: no

<7> [48.961846] i915 device info: has_one_eu_per_fuse_bit: no

<7> [48.961847] i915 device info: has_pxp: no

<7> [48.961848] i915 device info: has_rc6: yes

<7> [48.961849] i915 device info: has_rc6p: no

<7> [48.961850] i915 device info: has_rps: yes

<7> [48.961851] i915 device info: has_runtime_pm: yes

<7> [48.961853] i915 device info: has_snoop: no

<7> [48.961854] i915 device info: has_coherent_ggtt: yes

<7> [48.961855] i915 device info: tuning_thread_rr_after_dep: no

<7> [48.961856] i915 device info: unfenced_needs_alignment: no

<7> [48.961857] i915 device info: hws_needs_physical: no

<7> [48.961858] i915 device info: has_pooled_eu: no

<7> [48.961859] i915 device info: rawclk rate: 24000 kHz

<7> [48.961861] i915 device info: display version: 9

<7> [48.961862] i915 device info: cursor_needs_physical: no

<7> [48.961863] i915 device info: has_cdclk_crawl: no

<7> [48.961864] i915 device info: has_cdclk_squash: no

<7> [48.961866] i915 device info: has_ddi: yes

<7> [48.961867] i915 device info: has_dp_mst: yes

<7> [48.961868] i915 device info: has_dsb: no

<7> [48.961869] i915 device info: has_fpga_dbg: yes

<7> [48.961870] i915 device info: has_gmch: no

<7> [48.961871] i915 device info: has_hotplug: yes

<7> [48.961872] i915 device info: has_hti: no

<7> [48.961873] i915 device info: has_ipc: yes

<7> [48.961875] i915 device info: has_overlay: no

<7> [48.961876] i915 device info: has_psr: yes

<7> [48.961877] i915 device info: has_psr_hw_tracking: yes

<7> [48.961878] i915 device info: overlay_needs_physical: no

<7> [48.961879] i915 device info: supports_tv: no

<7> [48.961880] i915 device info: has_hdcp: yes

<7> [48.961881] i915 device info: has_dmc: yes

<7> [48.961882] i915 device info: has_dsc: no

<7> [48.961884] i915 device info: iommu: enabled

<7> [48.961885] i915 device info: available engines: 40403

<7> [48.961887] i915 device info: slice total: 1, mask=0001

<7> [48.961888] i915 device info: subslice total: 3

<7> [48.961889] i915 device info: slice0: 3 subslices, mask=00000007

<7> [48.961891] i915 device info: slice1: 0 subslices, mask=00000000

<7> [48.961892] i915 device info: slice2: 0 subslices, mask=00000000

<7> [48.961893] i915 device info: EU total: 24

<7> [48.961895] i915 device info: EU per subslice: 8

<7> [48.961896] i915 device info: has slice power gating: no

<7> [48.961897] i915 device info: has subslice power gating: no

<7> [48.961898] i915 device info: has EU power gating: yes

<6> [48.961900] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled

<6> [48.961901] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [48.961902] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [48.961986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [48.962682] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [48.963218] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] status updated from unknown to disconnected

<7> [48.963441] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected

<7> [48.963451] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]

<7> [48.963459] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]

<7> [48.963746] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [48.964335] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [48.964941] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [48.965512] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [48.966854] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00

<7> [48.967821] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000

<7> [48.968603] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [48.968797] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [48.968957] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [48.969114] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [48.969777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [48.969967] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] status updated from unknown to disconnected

<7> [48.969979] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected

<7> [48.969993] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]

<7> [48.969999] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]

<7> [48.970152] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [48.972084] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [48.972279] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [48.973010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [48.974040] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [48.974045] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [48.974194] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [49.005359] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [49.005367] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [49.005599] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.005876] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] status updated from unknown to disconnected

<7> [49.005889] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected

<7> [49.005900] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [49.005928] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [49.005932] [drm:drm_client_modeset_probe] connector 107 enabled? no

<7> [49.005947] [drm:drm_client_modeset_probe] connector 113 enabled? no

<7> [49.006090] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [49.006110] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [49.006128] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<6> [49.006154] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [49.006909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.007074] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [49.007594] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [49.008414] [drm:drm_client_modeset_probe]

<7> [49.008599] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]

<7> [49.008614] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]

<7> [49.008858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [49.009049] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [49.009225] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [49.009925] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.010272] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected

<7> [49.010280] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]

<7> [49.010287] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]

<7> [49.010549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.011033] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [49.011561] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [49.012114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [49.013528] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00

<7> [49.014535] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000

<7> [49.015231] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [49.015550] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [49.015744] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [49.015933] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [49.016587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.016822] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected

<7> [49.016832] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]

<7> [49.016840] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]

<7> [49.017017] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.018599] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [49.018774] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [49.019559] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [49.020109] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [49.020116] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [49.020283] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [49.048780] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [49.048788] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [49.048926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.049065] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected

<7> [49.049071] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [49.049080] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [49.049083] [drm:drm_client_modeset_probe] connector 107 enabled? no

<7> [49.049086] [drm:drm_client_modeset_probe] connector 113 enabled? no

<7> [49.049199] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [49.049216] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [49.049232] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<6> [49.049241] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [49.049318] [drm:drm_client_modeset_probe]

<7> [49.049342] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]

<7> [49.049347] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]

<7> [49.049471] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.049993] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.050137] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected

<7> [49.050142] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]

<7> [49.050147] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]

<7> [49.050271] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.050733] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [49.051254] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [49.051861] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [49.053191] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00

<7> [49.054228] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000

<7> [49.054871] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [49.055032] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [49.055168] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [49.055300] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [49.055907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.056061] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected

<7> [49.056067] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]

<7> [49.056073] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]

<7> [49.056197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.057244] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [49.057371] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [49.058041] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [49.058553] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [49.058560] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [49.058688] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [49.084946] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [49.084956] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [49.085098] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [49.085249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected

<7> [49.085256] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [49.085262] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [49.085267] [drm:drm_client_modeset_probe] connector 107 enabled? no

<7> [49.085272] [drm:drm_client_modeset_probe] connector 113 enabled? no

<7> [49.085306] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [49.085319] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [49.085338] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<6> [49.085345] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [49.097156] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [49.097954] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [49.098394] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [49.100895] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [49.101033] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [49.101514] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<6> [49.110435] [IGT] i915_module_load: finished subtest load, SUCCESS

<6> [49.110691] [IGT] i915_module_load: exiting, ret=0

Results for igt@i915_module_load@load