Results for igt@kms_cursor_legacy@basic-flip-before-cursor-legacy

Result: Skip

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.28-g08e87a32f (x86_64) (Linux: 6.6.0-rc6-linus-v6.6-rc6-g58720809f527+ x86_64)
Out	Opened device: /dev/dri/card0 No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. Subtest basic-flip-before-cursor-legacy: SKIP (0.000s) No valid crtc/connector combinations found.
Err	Subtest basic-flip-before-cursor-legacy: SKIP (0.000s)
Dmesg	<6> [103.295319] [IGT] kms_cursor_legacy: executing <7> [103.298794] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [103.299584] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [103.300007] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [103.307307] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [103.307318] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [103.307554] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.308272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [103.308892] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [103.309515] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [103.310327] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [103.310629] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [103.311694] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.313337] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.314947] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.316559] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.318318] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.320100] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.321855] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.323640] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.325253] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.326153] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [103.326972] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [103.327698] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [103.328237] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [103.328588] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [103.328911] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [103.329210] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [103.329978] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.330292] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [103.331530] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [103.331542] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [103.331818] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.332442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.332764] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [103.333889] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.333900] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.334195] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.385864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.405232] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.405247] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.405593] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.425548] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.425557] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.425829] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.426175] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [103.427146] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [103.427159] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [103.427472] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.428125] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [103.428742] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [103.429366] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [103.430248] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [103.430551] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [103.431664] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.433066] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.434639] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.436253] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.438016] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.439683] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.441467] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.443245] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.444868] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [103.445738] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [103.446701] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [103.447364] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [103.447875] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [103.448220] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [103.448520] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [103.448867] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [103.449623] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.449950] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [103.450002] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [103.450012] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [103.450303] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.450944] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.451259] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [103.451300] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [103.451309] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [103.451592] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [103.502863] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [103.520581] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.520593] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [103.520898] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [103.539145] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [103.539152] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [103.539344] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [103.539556] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <6> [103.540524] [IGT] kms_cursor_legacy: exiting, ret=77 <7> [103.541226] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-10-15 23:44:09