Results for igt@kms_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.28-g08e87a32f (x86_64) (Linux: 6.6.0-rc6-linus-v6.6-rc6-g58720809f527+ x86_64)
Out	Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 2 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915] intel_runtime_suspend+0xec/0x2a0 [i915] pci_pm_runtime_suspend+0x5a/0x1a0 __rpm_callback+0x3c/0x110 rpm_callback+0x58/0x70 rpm_suspend+0x118/0x5f0 pm_runtime_work+0x9f/0xb0 Wakeref count: 2 Wakeref x1 taken at: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] release_async_put_domains+0x3c/0xd0 [i915] intel_display_power_flush_work+0xb4/0x100 [i915] intel_hdmi_detect+0xd3/0x160 [i915] drm_helper_probe_detect_ctx+0x89/0x100 check_connector_changed+0x47/0x1b0 drm_helper_hpd_irq_event+0x96/0x110 i915_hpd_poll_init_work+0xaf/0xf0 [i915] Wakeref x1 taken at: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] __intel_display_power_put_async+0x3d/0x160 [i915] intel_atomic_commit_tail+0xa2e/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (0.266s)
Err	Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (0.266s)
Dmesg	<7> [67.412574] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [67.412702] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [67.412804] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [67.413976] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [67.423547] Console: switching to colour dummy device 80x25 <6> [67.423579] [IGT] kms_pm_rpm: executing <7> [67.426457] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [67.431775] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] <7> [67.431782] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [67.431913] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.432629] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.432760] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] disconnected <7> [67.433449] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] <7> [67.433458] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [67.433654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.434378] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.434527] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected <7> [67.434867] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] <7> [67.434870] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [67.434966] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.435636] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.435765] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected <7> [67.436093] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-3] <7> [67.436096] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [67.436220] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.436882] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.436989] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-3] disconnected <7> [67.437358] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:DP-2] <7> [67.437361] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [67.437538] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.438245] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.438357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:DP-2] disconnected <7> [67.438695] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:HDMI-A-4] <7> [67.438698] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [67.438794] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.439469] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.439584] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:HDMI-A-4] disconnected <7> [67.440366] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] <7> [67.440369] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [67.440517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.441351] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.441467] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] disconnected <7> [67.441479] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] <7> [67.441482] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [67.441583] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.442470] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.442583] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected <7> [67.442597] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] <7> [67.442600] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [67.442693] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.443628] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.443740] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected <7> [67.443753] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-3] <7> [67.443756] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [67.443844] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.444780] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.444889] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-3] disconnected <7> [67.444900] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:DP-2] <7> [67.444903] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [67.444998] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.445988] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.446104] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:DP-2] disconnected <7> [67.446124] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:HDMI-A-4] <7> [67.446127] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [67.446227] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.447086] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.447213] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:HDMI-A-4] disconnected <7> [67.447235] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] <7> [67.447238] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [67.447328] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.448248] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.448364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:HDMI-A-1] disconnected <7> [67.448409] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] <7> [67.448412] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [67.448510] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.449397] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.449510] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected <7> [67.449555] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] <7> [67.449558] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [67.449656] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.450557] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.450667] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:255:HDMI-A-2] disconnected <7> [67.450715] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-3] <7> [67.450718] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [67.450807] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.451711] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.451820] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:259:HDMI-A-3] disconnected <7> [67.451865] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:DP-2] <7> [67.451868] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [67.451965] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.452869] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.452983] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:DP-2] disconnected <7> [67.453027] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:HDMI-A-4] <7> [67.453030] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [67.453130] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [67.454016] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [67.454132] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:271:HDMI-A-4] disconnected <7> [68.457291] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.463282] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [68.466760] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.467920] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.468057] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.468197] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.468332] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.468459] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.468578] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.468695] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.468825] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.468945] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.469063] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.469214] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.469446] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.469628] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.469789] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.469903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.470221] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.495514] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.495874] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.496498] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.497069] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.498148] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.499231] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [68.499713] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.500292] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.502335] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.502690] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.517946] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [68.520303] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [68.521396] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.521619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.522646] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [68.522681] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.522894] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:236:HDMI-A-1] Same epoch counter 8 <7> [68.523083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.523258] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.523923] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.525132] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.525266] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.525396] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.525522] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.525646] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.525769] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.525890] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.526019] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.526161] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.526290] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.526438] [drm:drm_mode_setcrtc] [CRTC:131:pipe B] <7> [68.526439] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [68.526579] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.526738] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.526856] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.528040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.528172] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:246:DP-1] Same epoch counter 1 <7> [68.528177] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [68.528276] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.529288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.529423] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1 <7> [68.529428] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [68.529528] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.530384] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.530507] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1 <7> [68.530513] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [68.530611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.531517] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.531641] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:263:DP-2] Same epoch counter 1 <7> [68.531734] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.531860] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.532658] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.533849] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.533981] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.534101] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.534242] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.534375] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.534493] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.534615] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.534737] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.534854] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.534971] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.535133] [drm:drm_mode_setcrtc] [CRTC:182:pipe C] <7> [68.535235] [drm:drm_mode_setcrtc] [CRTC:233:pipe D] <7> [68.535237] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [68.535406] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.535529] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.535661] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.536876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.537006] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1 <7> [68.537013] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.541500] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [68.543848] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.544970] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.545113] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.545246] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.545371] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.545495] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.545617] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.545741] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.545869] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.545991] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.546117] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.546261] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.546481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.546658] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.546816] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.546928] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.547113] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.571974] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.572191] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.572498] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.572815] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.573516] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.574192] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [68.574529] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.574963] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.576891] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.577265] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.593729] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [68.596032] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.596137] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.596258] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.597172] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.598361] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.598488] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.598608] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.598726] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.598842] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.598959] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.599078] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.599215] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.599343] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.599463] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.599677] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [68.599796] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.599909] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.600013] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.601195] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.601313] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:236:HDMI-A-1] Same epoch counter 8 <7> [68.601318] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [68.601416] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.602372] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.602492] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:246:DP-1] Same epoch counter 1 <7> [68.602497] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [68.602596] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.603535] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.603651] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1 <7> [68.603655] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [68.603754] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.604701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.604816] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1 <7> [68.604820] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [68.604917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.605838] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.605959] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:263:DP-2] Same epoch counter 1 <7> [68.605963] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [68.606058] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.606984] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.607149] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1 <7> [68.607159] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.609322] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [68.611662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.612798] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.613143] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.613471] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.613695] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.613995] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.614307] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.614549] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.614774] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.614983] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.615188] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.615394] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.615796] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.615985] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.616158] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.616278] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.616415] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [68.701518] [IGT] kms_pm_rpm: starting subtest basic-pci-d3-state <7> [68.710905] [drm:drm_mode_setcrtc] [CRTC:80:pipe A] <7> [68.722328] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.722646] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.723215] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.723770] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.724654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.725232] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [68.725644] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.726147] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.728085] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.728427] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.741572] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [68.743816] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.743916] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.744051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.744955] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.746143] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.746279] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.746407] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.746530] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.746656] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.746779] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.746901] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.747024] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.747155] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.747286] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.747459] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [68.747610] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.747728] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.747839] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.747996] [drm:drm_mode_setcrtc] [CRTC:131:pipe B] <7> [68.749014] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.749136] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:236:HDMI-A-1] Same epoch counter 8 <7> [68.749146] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [68.749247] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.750199] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.750324] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:246:DP-1] Same epoch counter 1 <7> [68.750386] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.750504] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.751324] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.752522] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.752655] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.752785] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.752908] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.753026] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.753150] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.753273] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.753397] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.753568] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.753723] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.753913] [drm:drm_mode_setcrtc] [CRTC:182:pipe C] <7> [68.753914] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [68.754044] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.754187] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.754300] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.755477] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.755597] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1 <7> [68.755601] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [68.755700] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.756654] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.756778] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1 <7> [68.756782] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [68.756890] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.757803] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.757921] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:263:DP-2] Same epoch counter 1 <7> [68.757930] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.761320] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [68.764749] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.765890] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.766033] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.766174] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.766310] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.766434] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.766557] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.766684] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.766811] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.766934] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.767060] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.767207] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.767427] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.767607] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.767771] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.767889] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.768030] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.792695] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.792925] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.793346] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.793861] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.794686] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.795170] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [68.795710] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.796281] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.798480] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.798978] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.815676] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [68.817905] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.818008] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.818131] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.819052] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.820243] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.820365] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.820481] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.820596] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.820709] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.820822] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.820936] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.821068] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.821250] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.821399] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.821564] [drm:drm_mode_setcrtc] [CRTC:233:pipe D] <7> [68.821641] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [68.821785] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.821907] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.822021] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.823212] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.823333] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1 <7> [68.823342] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [68.823447] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.824393] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.824599] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:236:HDMI-A-1] Same epoch counter 8 <7> [68.824588] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.824705] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.825526] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.826712] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.826841] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.826964] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.827086] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.827218] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.827342] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.827462] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.827624] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.827797] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.827928] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.828162] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [68.828322] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.828440] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.828551] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.829726] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.829847] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:246:DP-1] Same epoch counter 1 <7> [68.829852] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <7> [68.829954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.830901] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.831026] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1 <7> [68.831030] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [68.831138] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.832048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.832169] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1 <7> [68.832173] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [68.832279] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.833204] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.833323] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:263:DP-2] Same epoch counter 1 <7> [68.833326] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [68.833424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.834373] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.834494] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1 <7> [68.834502] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [68.836696] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [68.839014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.840142] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.840285] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.840412] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.840540] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.840695] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.840838] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.840960] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.841087] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.841222] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.841351] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.841489] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [68.841701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [68.841869] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.842024] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [68.842140] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [68.842285] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [68.942071] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [68.942795] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [68.943470] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [68.944320] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [68.945447] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [68.946350] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [68.946756] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [68.946933] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [68.947640] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.947754] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.961680] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [68.963973] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1] <7> [68.965137] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [68.965290] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.966315] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:236:HDMI-A-1] Same epoch counter 8 <7> [68.966323] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1] <7> [68.966532] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:246:DP-1] Same epoch counter 1 <7> [68.966538] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2] <6> [68.967498] [IGT] kms_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS <7> [68.967496] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.967777] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1 <7> [68.967783] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3] <7> [68.967927] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.968663] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.968838] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1 <7> [68.968844] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2] <7> [68.968959] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.969814] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.969936] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:263:DP-2] Same epoch counter 1 <7> [68.969940] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4] <7> [68.970039] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.970955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [68.971067] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1 <7> [68.980601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [68.980732] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [68.981424] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [68.982646] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.982775] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [68.982897] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.983019] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [68.983151] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.983274] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [68.983391] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.983510] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [68.983630] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [68.983749] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <7> [68.983855] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [68.983968] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [68.984159] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <7> [68.996888] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [68.997183] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [68.997387] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [68.997577] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [68.997762] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [68.999014] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [69.041642] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [69.042335] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [69.043565] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [69.044723] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [69.045335] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [69.045845] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [69.046390] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [69.046874] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [69.047344] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [69.047760] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [69.048233] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [69.048679] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [69.049036] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it. <6> [69.049505] [IGT] kms_pm_rpm: exiting, ret=0 <6> [69.050259] Console: switching to colour frame buffer device 128x48

Created at 2023-10-15 23:44:09