Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-gd1db7333d (x86_64) (Linux: 6.6.0-rc5-linus-v6.6-rc5-g94f6f0550c62+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.257s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.257s)
Dmesg
<6> [265.572627] Console: switching to colour dummy device 80x25
<6> [265.573384] [IGT] kms_force_connector_basic: executing
<7> [265.792913] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [265.793624] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [265.793888] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [265.794709] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [265.794723] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [265.794738] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [265.795126] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [265.795423] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [265.795912] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.796227] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [265.796734] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.797061] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.797073] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [265.797365] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [265.799305] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.799317] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [265.799590] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [265.799865] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [265.799934] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [265.799945] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [265.800301] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [265.800591] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [265.801075] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.801360] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [265.801832] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.802149] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.802158] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [265.802446] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [265.804262] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.804273] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [265.804547] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [265.804821] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [265.805001] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [265.805011] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [265.805357] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [265.805645] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [265.806134] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.806414] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [265.806885] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.807293] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.807303] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [265.807611] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [265.809421] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.809431] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [265.809702] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [265.809976] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<6> [265.810990] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [265.811419] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing
<7> [265.811433] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [265.811445] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from disconnected to connected
<7> [265.811864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.812231] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [265.812738] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.813032] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.813089] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [265.813381] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [265.815358] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.815387] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [265.815791] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [265.815802] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [265.815814] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [265.815824] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [265.815834] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [265.815843] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [265.815926] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [265.816145] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.816363] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [265.816742] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [265.816935] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.816951] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [265.817177] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [265.818687] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [265.818702] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [265.818967] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [265.818974] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [265.818981] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [265.818987] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [265.818992] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [265.818997] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [266.055096] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [266.055139] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.055469] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [266.055478] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [266.055620] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [266.055629] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [266.055637] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [266.055644] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [266.055652] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [266.055657] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [266.055663] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [266.055669] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [266.055674] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [266.055679] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [266.055822] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [266.055921] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.056140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.056413] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.056787] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.056982] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.056998] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.057227] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.058710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.058725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.058980] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [266.058988] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [266.058995] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [266.059002] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [266.059009] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] probed modes :
<7> [266.059015] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [266.059021] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [266.059026] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [266.059031] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [266.059037] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [266.059338] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing
<7> [266.059351] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.059364] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.059594] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.059786] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.060191] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.060428] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.060806] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.060995] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.061002] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.061256] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.062801] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.062809] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.062999] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.063237] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from connected to disconnected
<7> [266.063262] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [266.063272] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 57
<7> [266.063386] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.063395] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.063598] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.063787] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.064156] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.064486] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.064986] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.065316] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.065327] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.065621] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.067454] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.067468] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.067769] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.068063] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<6> [266.069235] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [266.069519] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [266.070408] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [266.070422] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [266.070438] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [266.070450] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [266.070558] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [266.070566] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [266.070630] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [266.070641] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [266.070650] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [266.070734] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [266.070741] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [266.070930] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:LVDS-1] EDID override reset
<7> [266.070969] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [266.070979] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [266.070988] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [266.071069] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [266.071076] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [266.071386] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [266.071398] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.071409] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.071734] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.072008] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.072542] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.072814] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.073311] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.073584] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.073594] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.073865] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.075794] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.075805] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.076078] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.076399] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [266.076481] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.076493] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.076791] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.077060] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.077621] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.077891] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.078353] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.078624] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.078633] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.078902] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.080710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.080721] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.080993] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.081307] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [266.081531] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [266.081571] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.081582] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.081872] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.082151] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.082701] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.082970] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.083490] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.083760] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.083769] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.084039] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.085862] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.085872] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.086151] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.086564] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [266.086884] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [266.086896] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [266.086908] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [266.140019] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [266.156277] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.156291] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.156502] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [266.172282] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.172291] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [266.172481] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [266.172556] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [266.172564] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [266.223691] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [266.240307] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.240319] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.240520] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [266.256324] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.256338] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [266.256549] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [266.256726] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:68:HDMI-A-1] EDID override reset
<7> [266.256754] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [266.256762] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [266.307095] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [266.323367] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.323378] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.323561] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [266.339349] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.339357] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [266.339546] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [266.339747] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:DP-1] EDID override reset
<7> [266.339775] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [266.339783] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [266.339981] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [266.340165] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [266.340172] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [266.340179] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [266.340668] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.340880] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [266.341224] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.341489] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.341501] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.341759] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [266.343370] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.343382] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [266.343596] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [266.343669] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [266.343678] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [266.344104] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.344359] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [266.344735] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.344925] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.344932] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.345117] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [266.346586] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.346594] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [266.346791] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [266.346951] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:81:HDMI-A-2] EDID override reset
<7> [266.346979] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [266.346986] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [266.347404] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.347613] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [266.347988] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.348178] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.348184] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.348390] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [266.349843] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.349851] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [266.350044] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [266.350256] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [266.350264] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [266.350271] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [266.350737] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.350929] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [266.351370] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.351562] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.351570] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.351756] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [266.353280] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.353289] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [266.353511] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [266.353588] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [266.353600] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [266.354016] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.354205] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [266.354614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.354805] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.354811] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.354996] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [266.356469] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.356477] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [266.356673] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [266.356817] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:85:HDMI-A-3] EDID override reset
<7> [266.356843] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [266.356850] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [266.357248] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.357466] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [266.357876] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.358065] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.358071] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.358256] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [266.359736] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.359744] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [266.359939] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [266.360094] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:89:DP-2] EDID override reset
<7> [266.360119] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [266.360127] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [266.360375] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [266.360589] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:93:DP-3] EDID override reset
<7> [266.360615] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [266.360622] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [266.360831] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<6> [266.361921] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [266.362133] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [266.362144] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.362154] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.362425] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.362638] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.363045] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.363237] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.363710] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.363903] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.363911] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.364101] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.365625] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.365633] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.365824] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.366016] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [266.366103] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [266.366111] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [266.366121] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [266.366128] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [266.366201] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [266.366207] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [266.366270] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [266.366276] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [266.366283] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [266.418689] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [266.434402] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.434413] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.434599] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [266.450421] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.450430] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [266.450625] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [266.450726] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [266.450735] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [266.450743] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [266.451150] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.451701] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [266.453029] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.453875] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.453901] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.454634] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [266.457056] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.457069] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [266.457387] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [266.457506] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [266.457518] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [266.457530] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [266.458014] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.458304] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [266.458869] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.459162] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.459172] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.459482] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [266.461438] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.461450] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [266.461733] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [266.462192] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [266.478685] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [266.478716] [drm:drm_client_modeset_probe]
<7> [266.478891] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [266.478927] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [266.478951] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [266.479156] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [266.479174] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [266.479199] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [266.479220] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [266.479974] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x20f40000, result 0
<7> [266.480305] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [266.480826] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.481100] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [266.481567] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [266.481774] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.481782] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.481975] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [266.483538] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [266.483547] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [266.483740] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [266.483947] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [266.483957] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [266.483965] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [266.534739] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [266.551498] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.551511] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.551722] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [266.567509] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [266.567519] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [266.567712] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [266.567723] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [266.567730] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [266.567928] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [266.567935] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [266.567942] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [266.568288] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.568513] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [266.568961] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [266.569243] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.569253] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.569596] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [266.571513] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [266.571525] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [266.571806] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [266.571818] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [266.571829] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [266.572298] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.572635] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [266.573017] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [266.573210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.573218] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [266.573404] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [266.575260] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [266.575268] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [266.575577] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [266.575592] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [266.575604] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [266.575955] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [266.575970] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [266.575982] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [266.576312] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [266.576324] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [266.576333] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [266.576341] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [266.576347] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [266.576354] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [266.576361] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [266.576367] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [266.576374] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [266.576443] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [266.576464] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [266.576472] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [266.576479] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [266.576485] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [266.576517] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [266.595923] Console: switching to colour frame buffer device 170x48
Created at 2023-10-08 22:33:31