Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-gd1db7333d (x86_64) (Linux: 6.6.0-rc5-linus-v6.6-rc5-g94f6f0550c62+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x7c/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xec/0x2a0 [i915]
   pci_pm_runtime_suspend+0x5d/0x1a0
   __rpm_callback+0x3f/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.219s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.219s)
Dmesg
<6> [67.511278] Console: switching to colour dummy device 80x25
<6> [67.511327] [IGT] i915_pm_rpm: executing
<7> [67.518115] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [67.518497] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [67.518522] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [67.518766] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.519288] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.519485] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [67.519599] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [67.519606] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [67.519781] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.520305] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [67.520843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [67.521394] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [67.522549] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [67.523206] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [67.523858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [67.524085] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [67.524273] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [67.524471] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [67.525162] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.525422] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [67.525526] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [67.525534] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [67.525731] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.526922] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [67.527098] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [67.527850] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [67.528377] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [67.528383] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [67.528557] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [67.554857] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [67.554864] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [67.555008] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.555140] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [67.558695] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [67.558701] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [67.558843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.559305] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.559440] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [67.559864] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [67.559870] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [67.559991] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.560453] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [67.560983] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [67.561590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [67.562734] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [67.563816] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [67.564535] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [67.564697] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [67.564828] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [67.564956] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [67.565575] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.565726] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [67.566125] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [67.566130] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [67.566249] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.567278] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [67.567390] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [67.568063] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [67.568621] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [67.568626] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [67.568764] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [67.593325] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [67.593329] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [67.593439] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.593578] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [67.593926] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [67.593931] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [67.594053] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.594552] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.594702] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [67.594718] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [67.594722] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [67.594841] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.595301] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [67.595843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [67.596381] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [67.597536] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [67.598534] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [67.599280] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [67.599431] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [67.599604] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [67.599750] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [67.600342] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.600487] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [67.600518] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [67.600546] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [67.600679] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [67.601754] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [67.601881] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [67.602627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [67.603076] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [67.603080] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [67.603190] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [67.631597] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [67.631604] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [67.631782] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [67.631932] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [78.677394] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [78.681661] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [78.705636] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [78.711360] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [78.712476] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [78.713023] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [78.718529] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [78.742821] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [78.748160] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [78.748352] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.748549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.749052] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.749741] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [78.749741] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.750079] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.750341] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.750550] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.751205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.751801] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [78.751924] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.752093] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.752584] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.753215] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [78.753220] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.753452] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.754971] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.756075] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.756706] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.756937] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.757071] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.757201] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.757811] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.758008] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [78.758017] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.758205] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.759637] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.759754] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.760614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.761079] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.761083] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.761194] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.787422] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.787427] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.787547] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.787919] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [78.787937] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.788063] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.788557] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.788736] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [78.788745] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.788867] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.789329] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.789882] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.790421] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.791868] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.792987] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.793790] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.793955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.794088] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.794217] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.794828] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.794981] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [78.794999] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [78.797332] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [78.821701] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [78.826508] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [78.826678] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.826817] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.827269] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.827959] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.828461] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.828696] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.829196] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.829385] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.829391] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.829549] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.833725] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.833730] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.833848] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.833982] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.834112] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.834704] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.834883] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [78.834896] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.835018] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.835481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.835689] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [78.835717] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.835851] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.836314] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.836856] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.837417] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.838542] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.839538] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.840298] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.840454] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.840604] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.840738] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.841335] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.841476] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [78.841481] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.841611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.842726] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.842841] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.843554] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.844015] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.844020] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.844132] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.869811] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.869815] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.869925] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.870064] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [78.871077] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [78.872416] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [78.929749] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [78.936977] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [78.949200] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [78.953540] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [78.953706] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.953886] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.954368] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.954980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [78.955153] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.955324] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.955560] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [78.955488] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.956125] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.956305] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [78.956313] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [78.956466] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.956979] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [78.957491] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [78.958055] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [78.959285] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [78.960288] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [78.960956] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [78.961168] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [78.961357] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [78.961555] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [78.962203] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.962401] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [78.962410] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [78.962588] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [78.963729] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.963852] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [78.964552] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [78.965041] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.965046] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [78.965164] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [78.989158] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [78.989163] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [78.989275] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [78.989413] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [78.990438] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [78.992576] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [79.017015] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [79.021980] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [79.022153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.022317] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [79.022797] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [79.023460] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [79.023667] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [79.023851] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [79.024031] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [79.024665] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [79.024676] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [79.024871] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [79.025211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.025383] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [79.025871] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [79.026559] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [79.026769] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [79.027878] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [79.028699] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [79.029534] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [79.029747] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [79.029935] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [79.030117] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [79.030773] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [79.030922] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [79.030929] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [79.031058] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.032163] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.032287] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [79.032985] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.033450] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.033454] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [79.033584] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [79.057102] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.057107] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [79.057218] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [79.057357] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [79.058366] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [79.060825] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [79.139296] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [79.146436] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [79.146764] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.147039] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [79.147649] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [79.149237] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [79.149655] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [79.149998] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [79.150330] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [79.150681] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [79.151499] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [79.152413] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [79.152431] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [79.152724] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.153347] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [79.153894] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [79.154463] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [79.155781] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [79.156485] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [79.157040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [79.157271] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [79.157415] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [79.157571] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [79.158164] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [79.158313] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [79.158405] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [79.158544] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.159640] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.159762] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [79.160454] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [79.160955] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.160960] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [79.161078] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [79.185683] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [79.185687] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [79.185818] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [79.185952] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [79.186124] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [79.186279] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [79.186755] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [79.187468] [IGT] i915_pm_rpm: exiting, ret=0
<6> [79.188453] Console: switching to colour frame buffer device 128x48
Created at 2023-10-08 22:33:30