Results for igt@i915_module_load@load

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out 
Starting subtest: load
Opened device: /dev/dri/card0
Subtest load: SUCCESS (4.549s)
Err 
Starting subtest: load
Subtest load: SUCCESS (4.549s)
Dmesg
<6> [77.685860] [IGT] i915_module_load: executing
<6> [78.136281] [IGT] i915_module_load: starting subtest load
<4> [80.699855]
<4> [80.699868] **********************************************************
<4> [80.699870] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [80.699872] ** **
<4> [80.699874] ** trace_printk() being used. Allocating extra memory. **
<4> [80.699876] ** **
<4> [80.699878] ** This means that this is a DEBUG kernel and it is **
<4> [80.699880] ** unsafe for production use. **
<4> [80.699881] ** **
<4> [80.699883] ** If you see this message and you are not debugging **
<4> [80.699885] ** the kernel, report this immediately to your vendor! **
<4> [80.699887] ** **
<4> [80.699889] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [80.699891] **********************************************************
<7> [80.770661] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [80.770958] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found CougarPoint PCH
<7> [80.771196] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [80.771663] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 125000 kHz
<7> [80.772796] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 2048M
<7> [80.773015] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [80.773208] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [80.774057] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [80.778251] Console: switching to colour dummy device 80x25
<7> [80.780002] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 00000000
<7> [80.780402] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 65536K
<7> [80.781339] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xdaef6018
<7> [80.781994] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [80.782347] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [80.782844] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [80.783187] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [80.790112] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000483, SBCB callbacks 00000203
<7> [80.790409] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [80.790712] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [80.790985] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [80.791780] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [80.792096] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SANDYBRIDGE-M ", BDB version 161
<7> [80.792342] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [80.792611] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 269, min size 5)
<7> [80.792905] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [80.793143] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 22 (size 75, min size 22)
<7> [80.793378] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 23 (size 72, min size 72)
<7> [80.793645] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 200, min size 812)
<7> [80.793936] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 24, min size 34)
<7> [80.794176] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [80.794424] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1264, min size 1366)
<7> [80.794813] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 97, min size 305)
<7> [80.795153] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [80.795486] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 1 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [80.795869] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [80.796150] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1022
<7> [80.796389] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [80.796698] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [80.797027] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [80.797359] i915 0000:00:02.0: [drm:intel_bios_init [i915]] No SDVO device info is found in VBT
<7> [80.797686] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [80.797918] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 1
<7> [80.798147] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [80.798377] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 1
<7> [80.798653] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [80.798931] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 1
<7> [80.799221] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 00
<7> [80.799749] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.801137] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 0
<7> [80.801775] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 7 (0.7 usec)
<7> [80.802117] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 3 (1.5 usec)
<7> [80.802447] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 4 (2.0 usec)
<7> [80.802806] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency 22 (11.0 usec)
<7> [80.803130] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 7 (0.7 usec)
<7> [80.803460] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 3 (1.5 usec)
<7> [80.803860] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 4 (2.0 usec)
<7> [80.804198] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency 22 (11.0 usec)
<7> [80.804474] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 7 (0.7 usec)
<7> [80.804723] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 3 (1.5 usec)
<7> [80.804991] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 4 (2.0 usec)
<7> [80.805275] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency 22 (11.0 usec)
<7> [80.805618] i915 0000:00:02.0: [drm:i9xx_wm_init [i915]] WM latency values increased to avoid potential underruns
<7> [80.805904] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 12 (1.2 usec)
<7> [80.806161] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 3 (1.5 usec)
<7> [80.806381] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 4 (2.0 usec)
<7> [80.806653] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency 22 (11.0 usec)
<7> [80.806927] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 12 (1.2 usec)
<7> [80.807148] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 3 (1.5 usec)
<7> [80.807369] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 4 (2.0 usec)
<7> [80.807661] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency 22 (11.0 usec)
<7> [80.807955] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 12 (1.2 usec)
<7> [80.808176] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 3 (1.5 usec)
<7> [80.808394] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 4 (2.0 usec)
<7> [80.808664] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency 22 (11.0 usec)
<7> [80.808927] i915 0000:00:02.0: [drm:i9xx_wm_init [i915]] LP3 watermarks disabled due to potential for lost interrupts
<7> [80.809146] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 12 (1.2 usec)
<7> [80.809365] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 3 (1.5 usec)
<7> [80.809607] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 4 (2.0 usec)
<7> [80.809874] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency not provided
<7> [80.810094] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 12 (1.2 usec)
<7> [80.810314] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 3 (1.5 usec)
<7> [80.810571] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 4 (2.0 usec)
<7> [80.810865] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency not provided
<7> [80.811086] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 12 (1.2 usec)
<7> [80.811305] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 3 (1.5 usec)
<7> [80.811572] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 4 (2.0 usec)
<7> [80.811836] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency not provided
<7> [80.818377] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 2 display pipes available.
<7> [80.820097] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] FDI PLL freq=270000
<7> [80.820521] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 400000 kHz, VCO 0 kHz, ref 0 kHz, bypass 0 kHz, voltage level 0
<7> [80.820864] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 400000 kHz
<7> [80.821208] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 360000 kHz
<6> [80.821685] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem
<7> [80.822294] i915 0000:00:02.0: [drm:intel_lvds_init [i915]] LVDS PPS:t1+t2 300 t3 300 t4 5000 t5 3000 tx 2000 divider 6249 port 0 powerdown_on_reset 1
<7> [80.839552] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [80.839591] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [80.839718] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 3
<7> [80.840130] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] EDID PNPID mfg: LGD (0xe430), prod: 728, serial: 0, week: 0, year: 2010
<7> [80.840478] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (fallback): 0
<7> [80.841074] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 3
<7> [80.841432] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static
<7> [80.841956] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x8 0xa
<7> [80.842313] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 200300
<7> [80.842830] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 5, serial: 4, week: 0, year: 2002
<7> [80.843179] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [80.843706] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 210 Hz, active high, min brightness 0, level 0, controller 0
<7> [80.844074] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found SDVO panel mode in BIOS VBT tables: "1600x1200": 60 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x8 0xa
<7> [80.844413] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1
<7> [80.844853] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] No PSR BDB found.
<7> [80.845196] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:61:LVDS-1] using preferred EDID fixed mode: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [80.845709] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:61:LVDS-1] DRRS type: none
<7> [80.846058] i915 0000:00:02.0: [drm:pch_setup_backlight [i915]] [CONNECTOR:61:LVDS-1] Using native PCH PWM for backlight control
<7> [80.846297] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:61:LVDS-1] backlight initialized, enabled, brightness 4648/4648
<7> [80.846580] i915 0000:00:02.0: [drm:intel_lvds_init [i915]] detected single-link lvds configuration
<7> [80.846913] i915 0000:00:02.0: [drm:intel_crt_reset [i915]] crt adpa set to 0xf40000
<7> [80.847150] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [80.863573] [drm:intel_sdvo_read_byte [i915]] i2c transfer returned -6
<7> [80.863843] i915 0000:00:02.0: [drm:intel_sdvo_init [i915]] No SDVO device found on SDVOB
<7> [80.864484] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [80.864916] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:67:HDMI B]
<7> [80.865247] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:67:HDMI B] Using DDC pin 0x5 (VBT)
<7> [80.866012] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:75:DP B] Using AUX CH B (VBT)
<7> [80.866366] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:75:DP B]
<7> [80.867035] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:80:HDMI C]
<7> [80.867374] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:80:HDMI C] Using DDC pin 0x4 (VBT)
<7> [80.867952] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:84:HDMI D]
<7> [80.868274] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:84:HDMI D] Using DDC pin 0x6 (VBT)
<7> [80.868710] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:88:DP C] Using AUX CH C (VBT)
<7> [80.868940] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:88:DP C]
<7> [80.869300] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:92:DP D] Using AUX CH D (VBT)
<7> [80.869559] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:92:DP D]
<7> [80.869946] i915 0000:00:02.0: [drm:intel_init_pch_refclk [i915]] has_panel 1 has_lvds 1 has_ck505 0 using_ssc_source 0
<7> [80.870810] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:45:pipe A] hw state readout: enabled
<7> [80.871043] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:60:pipe B] hw state readout: disabled
<7> [80.871262] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:primary A] hw state readout: disabled, pipe A
<7> [80.871517] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:sprite A] hw state readout: disabled, pipe A
<7> [80.871815] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:cursor A] hw state readout: disabled, pipe A
<7> [80.872046] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:46:primary B] hw state readout: disabled, pipe B
<7> [80.872278] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:50:sprite B] hw state readout: disabled, pipe B
<7> [80.872581] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:56:cursor B] hw state readout: disabled, pipe B
<7> [80.872910] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:62:LVDS] hw state readout: enabled, pipe A
<7> [80.873160] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:66:CRT] hw state readout: disabled, pipe A
<7> [80.873392] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:67:HDMI B] hw state readout: disabled, pipe A
<7> [80.873666] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [80.873924] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:75:DP B] hw state readout: disabled, pipe A
<7> [80.874157] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:80:HDMI C] hw state readout: disabled, pipe A
<7> [80.874388] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:84:HDMI D] hw state readout: disabled, pipe A
<7> [80.874667] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [80.874935] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:88:DP C] hw state readout: disabled, pipe A
<7> [80.875172] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [80.875393] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:92:DP D] hw state readout: disabled, pipe A
<7> [80.875663] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:45:pipe A] reserving PCH DPLL A
<7> [80.875922] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] PCH DPLL A hw state readout: pipe_mask 0x1, on 1
<7> [80.876163] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] PCH DPLL B hw state readout: pipe_mask 0x0, on 0
<7> [80.876547] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:61:LVDS-1] hw state readout: enabled
<7> [80.876832] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:65:VGA-1] hw state readout: disabled
<7> [80.877068] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:68:HDMI-A-1] hw state readout: disabled
<7> [80.877306] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [80.877591] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:76:DP-1] hw state readout: disabled
<7> [80.877866] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:81:HDMI-A-2] hw state readout: disabled
<7> [80.878099] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:85:HDMI-A-3] hw state readout: disabled
<7> [80.878335] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [80.878592] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:89:DP-2] hw state readout: disabled
<7> [80.878874] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [80.879097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:93:DP-3] hw state readout: disabled
<7> [80.879488] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:primary A] min_cdclk 0 kHz
<7> [80.879757] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:sprite A] min_cdclk 0 kHz
<7> [80.880019] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:cursor A] min_cdclk 0 kHz
<7> [80.880241] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [80.880472] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:46:primary B] min_cdclk 0 kHz
<7> [80.880721] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:50:sprite B] min_cdclk 0 kHz
<7> [80.880978] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:56:cursor B] min_cdclk 0 kHz
<7> [80.881200] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [80.881630] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:45:pipe A] enable: yes [setup_hw_state]
<7> [80.881867] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: LVDS (0x10), output format: RGB, sink format: RGB
<7> [80.882096] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 18, dithering: 0
<7> [80.882325] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [80.882612] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [80.882886] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [80.883114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [80.883342] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] fdi: lanes: 4; data_m: 1314215, data_n: 8388608, link_m: 146023, link_n: 524288, tu: 64
<7> [80.883597] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [80.883857] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [80.884086] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [80.884314] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1366x768": 60 75238 720 1414 1478 1582 400 772 779 792 0x40 0x9
<7> [80.884567] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1366x768": 60 75238 1366 1414 1478 1582 768 772 779 792 0x40 0x9
<7> [80.884832] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [80.885063] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1366x768": 60 75238 1366 1414 1478 1582 768 772 779 792 0x40 0x9
<7> [80.885292] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [80.885565] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 75238, pipe src: 720x400+0+0, pixel rate 75238
<7> [80.885838] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 0, ips linetime: 0
<7> [80.886065] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 1366x768+0+0, enabled, force thru: no
<7> [80.886293] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [80.886558] i915 0000:00:02.0: [drm:ibx_dump_hw_state [i915]] dpll_hw_state: dpll: 0x88040004, dpll_md: 0x0, fp0: 0x10c07, fp1: 0x30d07
<7> [80.886830] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [80.887060] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [80.887289] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [80.887537] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [80.887804] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [80.888033] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [80.888260] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:60:pipe B] enable: no [setup_hw_state]
<7> [80.889140] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [80.889347] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 80000000]
<7> [80.905001] i915 0000:00:02.0: [drm:i915_gem_init [i915]] Wrong MCH_SSKPD value: 0x16040307 This can cause underruns.
<7> [80.907063] i915 0000:00:02.0: [drm:intel_rps_init [i915]] Overclocking supported, max: 1300MHz, overclock: 1300MHz
<7> [80.908641] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [80.908948] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on rcs'0
<7> [80.923170] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [PLANE:31:primary A] no fb, skipping
<7> [80.923452] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:60:pipe B] not active, skipping
<7> [80.923739] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [80.924073] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [80.924855] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [80.925109] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [80.925299] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [80.933023] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:61:LVDS-1] backlight device intel_backlight registered
<7> [80.933471] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:61:LVDS-1] generating connector hotplug event
<7> [80.934707] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:65:VGA-1] generating connector hotplug event
<7> [80.935573] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:68:HDMI-A-1] generating connector hotplug event
<7> [80.936343] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DP B bus for card0-DP-1
<7> [80.938308] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:76:DP-1] generating connector hotplug event
<7> [80.939514] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:81:HDMI-A-2] generating connector hotplug event
<7> [80.940362] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:85:HDMI-A-3] generating connector hotplug event
<7> [80.941795] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DP C bus for card0-DP-2
<7> [80.943155] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:89:DP-2] generating connector hotplug event
<7> [80.943792] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX D/DP D bus for card0-DP-3
<7> [80.944899] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:93:DP-3] generating connector hotplug event
<6> [80.944981] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [80.946931] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 8 outputs detected
<6> [80.954596] ACPI: video: Video Device [VID] (multi-head: yes rom: no post: no)
<6> [80.956601] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input10
<7> [80.959199] [drm:drm_client_modeset_probe]
<7> [80.959260] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [80.959639] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [80.959676] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] status updated from unknown to connected
<7> [80.959739] i915 device info: pciid=0x0126 rev=0x09 platform=SANDYBRIDGE (subplatform=0x0) gen=6
<7> [80.959746] i915 device info: graphics version: 6
<7> [80.959750] i915 device info: media version: 6
<7> [80.959755] i915 device info: graphics stepping: **
<7> [80.959759] i915 device info: media stepping: **
<7> [80.959762] i915 device info: display stepping: **
<7> [80.959766] i915 device info: base die stepping: **
<7> [80.959770] i915 device info: gt: 2
<7> [80.959774] i915 device info: memory-regions: 0x21
<7> [80.959778] i915 device info: page-sizes: 0x1000
<7> [80.959782] i915 device info: platform: SANDYBRIDGE
<7> [80.959785] i915 device info: ppgtt-size: 31
<7> [80.959789] i915 device info: ppgtt-type: 1
<7> [80.959793] i915 device info: dma_mask_size: 40
<7> [80.959797] i915 device info: is_mobile: yes
<7> [80.959800] i915 device info: is_lp: no
<7> [80.959804] i915 device info: require_force_probe: no
<7> [80.959808] i915 device info: is_dgfx: no
<7> [80.959812] i915 device info: has_64bit_reloc: no
<7> [80.959815] i915 device info: has_64k_pages: no
<7> [80.959820] i915 device info: gpu_reset_clobbers_display: no
<7> [80.959824] i915 device info: has_reset_engine: no
<7> [80.959828] i915 device info: has_3d_pipeline: yes
<7> [80.959832] i915 device info: has_4tile: no
<7> [80.959836] i915 device info: has_flat_ccs: no
<7> [80.959840] i915 device info: has_global_mocs: no
<7> [80.959844] i915 device info: has_gmd_id: no
<7> [80.959848] i915 device info: has_gt_uc: no
<7> [80.959852] i915 device info: has_heci_pxp: no
<7> [80.959855] i915 device info: has_heci_gscfi: no
<7> [80.959859] i915 device info: has_guc_deprivilege: no
<7> [80.959863] i915 device info: has_l3_ccs_read: no
<7> [80.959867] i915 device info: has_l3_dpf: no
<7> [80.959871] i915 device info: has_llc: yes
<7> [80.959875] i915 device info: has_logical_ring_contexts: no
<7> [80.959879] i915 device info: has_logical_ring_elsq: no
<7> [80.959882] i915 device info: has_media_ratio_mode: no
<7> [80.959886] i915 device info: has_mslice_steering: no
<7> [80.959890] i915 device info: has_oa_bpc_reporting: no
<7> [80.959894] i915 device info: has_oa_slice_contrib_limits: no
<7> [80.959898] i915 device info: has_oam: no
<7> [80.959901] i915 device info: has_one_eu_per_fuse_bit: no
<7> [80.959905] i915 device info: has_pxp: no
<7> [80.959909] i915 device info: has_rc6: yes
<7> [80.959913] i915 device info: has_rc6p: no
<7> [80.959916] i915 device info: has_rps: yes
<7> [80.959920] i915 device info: has_runtime_pm: no
<7> [80.959924] i915 device info: has_snoop: no
<7> [80.959928] i915 device info: has_coherent_ggtt: yes
<7> [80.959932] i915 device info: tuning_thread_rr_after_dep: no
<7> [80.959936] i915 device info: unfenced_needs_alignment: no
<7> [80.959939] i915 device info: hws_needs_physical: no
<7> [80.959943] i915 device info: has_pooled_eu: no
<7> [80.959947] i915 device info: rawclk rate: 125000 kHz
<7> [80.959951] i915 device info: display version: 6
<7> [80.959955] i915 device info: cursor_needs_physical: no
<7> [80.959959] i915 device info: has_cdclk_crawl: no
<7> [80.959963] i915 device info: has_cdclk_squash: no
<7> [80.959967] i915 device info: has_ddi: no
<7> [80.959970] i915 device info: has_dp_mst: no
<7> [80.959974] i915 device info: has_dsb: no
<7> [80.959978] i915 device info: has_fpga_dbg: no
<7> [80.959982] i915 device info: has_gmch: no
<7> [80.959985] i915 device info: has_hotplug: yes
<7> [80.959989] i915 device info: has_hti: no
<7> [80.959993] i915 device info: has_ipc: no
<7> [80.959997] i915 device info: has_overlay: no
<7> [80.960001] i915 device info: has_psr: no
<7> [80.960004] i915 device info: has_psr_hw_tracking: no
<7> [80.960008] i915 device info: overlay_needs_physical: no
<7> [80.960012] i915 device info: supports_tv: no
<7> [80.960015] i915 device info: has_hdcp: no
<7> [80.960019] i915 device info: has_dmc: no
<7> [80.960023] i915 device info: has_dsc: no
<7> [80.960027] i915 device info: iommu: disabled
<7> [80.960031] i915 device info: available engines: 403
<7> [80.960036] i915 device info: slice total: 0, mask=0000
<7> [80.960040] i915 device info: subslice total: 0
<7> [80.960043] i915 device info: EU total: 0
<7> [80.960046] i915 device info: EU per subslice: 0
<7> [80.960049] i915 device info: has slice power gating: no
<7> [80.960053] i915 device info: has subslice power gating: no
<7> [80.960057] i915 device info: has EU power gating: no
<6> [80.960061] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [80.960066] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [80.960070] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [80.960166] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [80.960180] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [80.960379] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [80.960393] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [80.960406] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [80.960417] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [80.960891] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] trigger hotplug detect cycle: adpa=0xf40000
<7> [80.969776] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [80.970192] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [80.971135] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [80.971963] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [80.972701] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [80.973062] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [80.973075] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.973418] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [80.975292] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [80.975304] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [80.975862] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [80.976480] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] status updated from unknown to disconnected
<7> [80.976568] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [80.976583] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [80.976597] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [81.028514] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [81.044561] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.044576] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.044850] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [81.060560] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [81.060575] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [81.060859] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] status updated from unknown to disconnected
<7> [81.060876] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [81.060885] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [81.060894] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [81.061143] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] status updated from unknown to disconnected
<7> [81.061155] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [81.061162] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [81.061169] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [81.061577] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [81.061921] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [81.062468] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [81.062918] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [81.062931] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.063276] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [81.065425] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [81.065439] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [81.065920] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] status updated from unknown to disconnected
<7> [81.066239] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [81.066253] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [81.066267] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [81.066991] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.067338] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [81.067873] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [81.068216] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.068228] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.068596] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [81.070655] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [81.070670] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [81.071035] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] status updated from unknown to disconnected
<7> [81.071060] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [81.071073] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [81.071086] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [81.071454] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] status updated from unknown to disconnected
<7> [81.071474] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [81.071486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [81.071515] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [81.071879] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] status updated from unknown to disconnected
<7> [81.071901] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [81.071911] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [81.071920] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [81.071928] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [81.071935] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [81.071943] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [81.071950] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [81.071958] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [81.071965] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [81.072186] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [81.072226] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [81.072234] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [81.072242] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [81.072250] [drm:drm_client_modeset_probe] picking CRTCs for 8192x8192 config
<7> [81.072275] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<7> [81.072408] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [81.072564] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [81.076414] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 1366x768 fb: 0x00002000
<6> [81.080042] fbcon: i915drmfb (fb0) is primary device
<7> [81.082294] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:61:LVDS-1] Limiting display bpp to 24 (EDID bpp 0, max requested bpp 0, max platform bpp 36)
<7> [81.082890] i915 0000:00:02.0: [drm:intel_lvds_compute_config [i915]] forcing display bpp (was 24) to LVDS (18)
<7> [81.083243] i915 0000:00:02.0: [drm:ilk_fdi_compute_config [i915]] checking fdi config on pipe A, lanes 1
<7> [81.083609] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:45:pipe A] hw max bpp: 24, pipe bpp: 18, dithering: 1
<7> [81.083958] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] initial modeset and fastboot not set
<7> [81.084284] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:45:pipe A] fastset requirement not met in fdi_lanes (expected 4, found 1)
<7> [81.084727] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:45:pipe A] fastset requirement not met in fdi_m_n (expected tu 64 data 1314215/8388608 link 146023/524288, found tu 64, data 5259517/8388608 link 146097/524288)
<7> [81.085084] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:45:pipe A] fastset requirement not met in dpll_hw_state.fp1 (expected 0x00030d07, found 0x00010c07)
<7> [81.085427] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [81.085810] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:45:pipe A] releasing PCH DPLL A
<7> [81.086195] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:45:pipe A] allocated PCH DPLL A
<7> [81.086614] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:45:pipe A] reserving PCH DPLL A
<7> [81.086955] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:45:pipe A] enable: yes [modeset]
<7> [81.087297] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: LVDS (0x10), output format: RGB, sink format: RGB
<7> [81.087703] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 18, dithering: 1
<7> [81.088039] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [81.088385] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [81.088749] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [81.089090] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [81.089429] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] fdi: lanes: 1; data_m: 5259517, data_n: 8388608, link_m: 146097, link_n: 524288, tu: 64
<7> [81.089833] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [81.090179] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [81.090588] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [81.090935] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [81.091282] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [81.091659] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [81.092011] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1366x768": 60 75238 1366 1414 1478 1582 768 772 779 792 0x40 0x9
<7> [81.092358] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [81.092765] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 75238, pipe src: 1366x768+0+0, pixel rate 75238
<7> [81.093111] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 0, ips linetime: 0
<7> [81.093456] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [81.093821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [81.094156] i915 0000:00:02.0: [drm:ibx_dump_hw_state [i915]] dpll_hw_state: dpll: 0x88040004, dpll_md: 0x0, fp0: 0x10c07, fp1: 0x10c07
<7> [81.094590] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x3 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [81.094936] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [81.095266] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [81.098526] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [81.098936] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [81.099287] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [81.099715] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:primary A] fb: [FB:64] 1366x768 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [81.100059] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [81.100403] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1366.000000x768.000000+0.000000+0.000000 dst: 1366x768+0+0
<7> [81.100818] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:sprite A] fb: [NOFB], visible: no
<7> [81.101159] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:cursor A] fb: [NOFB], visible: no
<7> [81.106020] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:61:LVDS-1] set backlight PWM = 0
<7> [81.107349] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [81.356589] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [81.356878] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [81.357110] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [81.372809] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable PCH DPLL A (active 0x1, on? 1) for [CRTC:45:pipe A]
<7> [81.373465] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling PCH DPLL A
<7> [81.374110] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:62:LVDS]
<7> [81.374460] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:66:CRT]
<7> [81.375373] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:67:HDMI B]
<7> [81.375798] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:75:DP B]
<7> [81.376136] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:80:HDMI C]
<7> [81.376473] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:84:HDMI D]
<7> [81.377059] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:88:DP C]
<7> [81.377435] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:92:DP D]
<7> [81.379039] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] PCH DPLL A
<7> [81.379381] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] PCH DPLL B
<7> [81.380566] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [81.381786] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI_RX_IIR 0x700
<7> [81.382129] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI train 1 done.
<7> [81.383044] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI_RX_IIR 0x600
<7> [81.383271] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI train 2 done.
<7> [81.383537] i915 0000:00:02.0: [drm:ilk_pch_enable [i915]] FDI train done.
<7> [81.383811] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable PCH DPLL A (active 0x1, on? 0) for [CRTC:45:pipe A]
<7> [81.384039] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling PCH DPLL A
<7> [81.897458] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [81.898445] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:61:LVDS-1] set backlight PWM = 4648
<7> [81.952345] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:61:LVDS-1]
<7> [81.952688] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:45:pipe A]
<7> [81.952983] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] PCH DPLL A
<7> [81.953893] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=4648/4648
<6> [81.954073] Console: switching to colour frame buffer device 170x48
<7> [81.954468] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:61:LVDS-1] set backlight level = 4648
<6> [81.971723] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [81.980834] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [81.980856] [drm:drm_client_modeset_probe]
<7> [81.981219] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [81.981254] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [81.981268] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [81.981666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [81.981704] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [81.981715] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [81.981725] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [81.982183] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [81.982485] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [81.983610] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [81.983936] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [81.984488] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [81.985250] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [81.985260] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [81.985585] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [81.987620] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [81.987632] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [81.987936] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [81.988218] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [81.988231] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [81.988240] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [82.041141] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [82.057566] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [82.057576] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.057761] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [82.073550] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [82.073558] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [82.073758] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [82.073767] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [82.073774] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [82.073973] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [82.073979] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [82.073984] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [82.074412] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [82.074738] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [82.075229] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [82.075540] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [82.075548] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.075838] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [82.077810] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [82.077819] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [82.078105] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [82.078115] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [82.078124] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [82.078565] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [82.078856] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [82.079335] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [82.079655] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [82.079663] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.079949] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [82.081906] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [82.081914] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [82.082196] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [82.082205] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [82.082214] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [82.082589] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [82.082599] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [82.082608] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [82.082922] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [82.082930] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [82.082936] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [82.082941] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [82.082946] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [82.082950] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [82.082955] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [82.082960] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [82.082964] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [82.083179] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [82.083215] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [82.083220] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [82.083226] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [82.083230] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [82.083281] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<7> [82.119061] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [82.119081] [drm:drm_client_modeset_probe]
<7> [82.119138] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1]
<7> [82.119152] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [82.119159] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [82.119234] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:61:LVDS-1] probed modes :
<7> [82.119239] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [82.119247] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1]
<7> [82.119253] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [82.119542] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [82.119825] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [82.120303] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [82.120634] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [82.121130] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [82.121405] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [82.121415] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.121749] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [82.123719] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [82.123728] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [82.124004] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [82.124591] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:65:VGA-1] disconnected
<7> [82.124606] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1]
<7> [82.124616] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [82.177106] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [82.193556] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [82.193565] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.193747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [82.209558] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [82.209566] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [82.209772] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [82.209781] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1]
<7> [82.209788] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [82.209985] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:76:DP-1] disconnected
<7> [82.209991] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2]
<7> [82.209996] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [82.210401] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [82.210642] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [82.211140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [82.211415] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [82.211423] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.211743] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [82.213738] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [82.213747] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [82.214031] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [82.214041] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3]
<7> [82.214049] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [82.214560] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [82.214851] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [82.215330] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [82.215676] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [82.215684] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.215971] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [82.217918] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [82.217926] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [82.218206] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [82.218216] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2]
<7> [82.218225] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [82.218580] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:89:DP-2] disconnected
<7> [82.218590] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3]
<7> [82.218599] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [82.218911] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:93:DP-3] disconnected
<7> [82.218918] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [82.218925] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [82.218930] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [82.218935] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [82.218939] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [82.218944] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [82.218948] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [82.218953] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [82.218992] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [82.219008] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [82.219013] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [82.219018] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [82.219023] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [82.219051] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<7> [82.635880] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [82.639251] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [82.653112] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [82.654727] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<6> [82.685267] [IGT] i915_module_load: finished subtest load, SUCCESS
<6> [82.685353] [IGT] i915_module_load: exiting, ret=0
<6> [82.794258] i915_module_loa (1117) used greatest stack depth: 11464 bytes left
<6> [82.978787] snd_hda_codec_generic hdaudioC0D0: autoconfig for Generic: line_outs=1 (0x1f/0x0/0x0/0x0/0x0) type:speaker
<6> [82.978802] snd_hda_codec_generic hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [82.978808] snd_hda_codec_generic hdaudioC0D0: hp_outs=1 (0x19/0x0/0x0/0x0/0x0)
<6> [82.978814] snd_hda_codec_generic hdaudioC0D0: mono: mono_out=0x0
<6> [82.978818] snd_hda_codec_generic hdaudioC0D0: inputs:
<6> [82.978823] snd_hda_codec_generic hdaudioC0D0: Internal Mic=0x23
<6> [82.978828] snd_hda_codec_generic hdaudioC0D0: Mic=0x1b
<6> [82.990657] modprobe (1193) used greatest stack depth: 11280 bytes left
<7> [83.106476] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [83.106805] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [83.107060] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [83.132970] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
<6> [83.142205] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
<6> [83.143753] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
<6> [83.145308] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
<6> [83.147417] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
Created at 2023-10-02 01:50:22