Results for igt@i915_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out 
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x7c/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_display_power_flush_work+0xe9/0x100 [i915]
   intel_dp_detect+0x231/0x630 [i915]
   drm_helper_probe_detect_ctx+0x45/0x100
   check_connector_changed+0x47/0x1b0
   drm_helper_hpd_irq_event+0x96/0x110
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
Subtest basic-rte: SUCCESS (11.665s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 2
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x7c/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xec/0x2a0 [i915]
   pci_pm_runtime_suspend+0x5d/0x1a0
   __rpm_callback+0x3f/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 2
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   release_async_put_domains+0x3c/0xd0 [i915]
   intel_display_power_flush_work+0xb4/0x100 [i915]
   intel_dp_detect+0x231/0x630 [i915]
   drm_helper_probe_detect_ctx+0x45/0x100
   check_connector_changed+0x47/0x1b0
   drm_helper_hpd_irq_event+0x96/0x110
   i915_hpd_poll_init_work+0xaf/0xf0 [i915]
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (11.665s)
Dmesg
<6> [91.966212] Console: switching to colour dummy device 80x25
<6> [91.966265] [IGT] i915_pm_rpm: executing
<6> [91.974989] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [91.975041] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [91.975428] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [91.975436] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.975601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.976142] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.976290] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [91.976351] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [91.976356] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.976488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.977012] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.977511] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.978084] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.979364] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.980146] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.980904] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.981065] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.981229] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.981374] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.981993] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.982195] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [91.982252] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [91.982257] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.982378] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.983481] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.983603] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.984303] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.985344] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.985348] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.985461] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.007909] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.007915] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.008042] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.008178] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [92.011702] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [92.011708] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [92.011835] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.012306] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.012442] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [92.012965] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [92.012971] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [92.013095] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.013559] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [92.014095] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [92.014671] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [92.015812] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [92.016889] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [92.017609] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [92.017772] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [92.017905] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [92.018033] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [92.019161] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.019357] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [92.019847] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [92.019852] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [92.019987] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.021571] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.021729] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.022445] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.022964] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.022968] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.023108] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.050423] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.050428] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.050544] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.050687] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [92.051066] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [92.051071] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [92.051209] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.051698] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.051899] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [92.051916] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [92.051920] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [92.052041] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.052503] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [92.053035] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [92.053636] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [92.054771] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [92.055853] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [92.056608] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [92.056770] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [92.056904] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [92.057033] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [92.057626] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.057783] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [92.057801] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [92.057806] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [92.057928] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [92.059520] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.059670] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [92.060362] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [92.060879] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.060885] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [92.061041] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [92.088346] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [92.088350] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [92.088464] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [92.088648] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [103.130301] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.138044] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.162705] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.167670] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.168271] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [103.168442] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.168610] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.169065] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.169704] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.169870] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.170026] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.170177] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.170602] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [103.170791] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.170954] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.170961] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.171104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.171602] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.172118] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.172695] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.173842] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.174940] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.175705] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.175873] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.176006] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.176136] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.176751] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.176914] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.176921] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.177042] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.178138] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.178269] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.179456] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.179995] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.180000] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.180112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.208001] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.208006] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.208120] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.208260] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.209772] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.211053] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.235465] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.239685] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.239828] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.239971] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.240410] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.241100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.241307] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [103.241316] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.241481] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.241655] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.242267] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.242437] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.242449] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.242595] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.243068] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.243597] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.244145] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.245391] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.246478] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.247239] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.247404] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.247547] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.247703] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.248307] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.248459] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.248558] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.248742] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.249206] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.249855] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.250339] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.250535] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.251019] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.251234] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.251241] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.251364] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.255836] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.255841] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.255960] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.256090] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.256217] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.256830] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.257006] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.257014] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.260612] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.351474] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [103.363677] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.369048] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.369234] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.369427] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.369954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.370839] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.371071] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.371290] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.371502] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.371789] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [103.372192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.372421] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.372430] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.372641] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.373194] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.373731] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.374287] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.375562] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.376268] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.376817] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.377074] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.377299] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.377519] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.378232] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.378420] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.378430] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.378559] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.379670] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.379794] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.380500] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.380980] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.380985] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.381105] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.406258] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.406263] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.406375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.406515] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.408037] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.409257] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.433663] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.439116] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.439445] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.439881] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.440554] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.441419] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.441813] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.442176] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [103.442182] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.442543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.443519] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.444074] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.444100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.444568] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.445343] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.446004] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.446699] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.447940] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.448740] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.449422] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.449676] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.449887] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.450092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.450771] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.450995] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.451005] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.451201] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.452351] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.452546] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.453370] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.453926] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.453933] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.454113] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.484736] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.484741] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.484884] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.485025] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.485961] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.488612] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.513022] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.518093] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.518266] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.518393] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.518921] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.519502] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.519680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.519828] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.519959] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.520540] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.520695] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.520726] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.520861] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.521346] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.521872] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.522433] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.523616] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.524611] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.525377] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.525543] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.525703] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.525844] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.526449] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.526681] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.526691] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.526856] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.527961] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.528086] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.528789] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.529284] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.529289] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.529409] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.555146] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.555151] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.555266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.555408] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.556948] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.558268] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.633238] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.637677] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.637877] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.638117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.638706] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.638902] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.639598] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.639611] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.639950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [103.640424] [IGT] i915_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [103.640473] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [103.641346] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.642049] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.642843] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.643015] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.643158] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.643298] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.643919] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.644072] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.644083] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.644218] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.645336] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.645461] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.646158] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.646681] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.646686] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.646813] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.670312] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.670318] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.670436] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.670589] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.672176] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.673500] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.697930] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.702593] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.702762] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.702927] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.703395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.704073] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.704258] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.704438] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.704615] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [103.704614] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.705232] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.705408] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.705418] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.705583] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.706087] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.706609] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.707163] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.708462] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.709597] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.710369] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.710534] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.710696] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.710836] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.711440] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.711606] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.711710] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.711914] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.712384] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.713032] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [103.713032] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.713455] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.713588] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.713986] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.714141] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.714146] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.714267] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.718335] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.718340] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.718468] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.718624] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.718765] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.719357] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.719507] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.719514] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.722980] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.747369] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.751989] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.752153] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.752314] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.752788] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.753446] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.753637] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.753802] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.753962] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.754588] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.754824] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.754834] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.755042] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.755612] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.756131] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.756726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.757959] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.759080] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.759887] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.760140] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.760360] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.760589] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.761265] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.761496] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.761506] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.761731] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.762961] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.763158] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.763954] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.764488] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.764495] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.764702] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.791019] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.791026] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.791212] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.791417] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [103.793031] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.795628] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [103.867691] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [103.874239] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [103.874529] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.874752] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.875305] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.876289] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [103.876532] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.876779] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<6> [103.876934] [IGT] i915_pm_rpm: exiting, ret=0
<7> [103.877027] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.877723] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.877975] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [103.877994] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [103.878207] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.878792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.879327] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [103.880073] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [103.881418] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [103.882188] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [103.882859] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [103.883117] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [103.883343] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [103.883563] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [103.884340] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.884641] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [103.884651] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [103.884858] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.886078] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.886373] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [103.887330] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [103.888428] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.888432] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [103.888554] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [103.916956] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [103.916960] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [103.917103] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [103.917238] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [103.917495] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [103.917713] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [103.918246] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [103.919037] Console: switching to colour frame buffer device 128x48
Created at 2023-10-02 01:50:22