Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 2
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x7c/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xec/0x2a0 [i915]
   pci_pm_runtime_suspend+0x5d/0x1a0
   __rpm_callback+0x3f/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 2
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   release_async_put_domains+0x3c/0xd0 [i915]
   intel_display_power_flush_work+0xb4/0x100 [i915]
   intel_dp_detect+0x231/0x630 [i915]
   drm_helper_probe_detect_ctx+0x45/0x100
   check_connector_changed+0x47/0x1b0
   drm_helper_hpd_irq_event+0x96/0x110
   i915_hpd_poll_init_work+0xaf/0xf0 [i915]
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x95/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1ec/0x740
   drm_ioctl_kernel+0xb6/0x150
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.289s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.289s)
Dmesg
<6> [80.203921] Console: switching to colour dummy device 80x25
<6> [80.203976] [IGT] i915_pm_rpm: executing
<7> [80.211710] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [80.212086] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [80.212093] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [80.212230] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.212728] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.212938] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [80.213000] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [80.213005] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [80.213127] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.213627] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [80.214109] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [80.214705] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [80.216064] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [80.217152] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [80.217835] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [80.217998] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [80.218135] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [80.218302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [80.218940] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.219105] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [80.219156] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [80.219161] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [80.219281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.220378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.220492] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [80.221053] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.221499] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.221504] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.221683] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [80.247916] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.247921] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [80.248046] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.248181] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [80.251634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [80.251640] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [80.251770] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.252229] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.252365] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [80.252815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [80.252820] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [80.252943] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.253405] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [80.253947] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [80.254484] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [80.255767] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [80.256877] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [80.257609] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [80.257774] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [80.257906] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [80.258034] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [80.258639] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.258818] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [80.259246] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [80.259251] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [80.259372] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.261008] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.261123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [80.262321] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.262896] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.262900] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.263015] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [80.287648] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.287665] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [80.287777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.287909] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [80.288203] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [80.288208] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [80.288327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.288834] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.289001] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [80.289017] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2]
<7> [80.289021] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [80.289158] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.289654] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [80.290152] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [80.290718] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [80.291936] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [80.293015] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [80.293769] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [80.293933] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [80.294065] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [80.294194] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [80.294805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.294985] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:107:DP-2] disconnected
<7> [80.295003] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1]
<7> [80.295007] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [80.295127] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [80.296237] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.296380] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [80.297612] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [80.298090] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.298094] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [80.298207] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [80.324989] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [80.325006] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [80.325117] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [80.325249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [91.371402] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.378140] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.402760] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.409170] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.410609] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.410822] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.411167] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.411830] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.413658] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.413536] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.414142] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.414363] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.414511] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.415170] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.415628] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [91.415753] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.415904] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.416369] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.417119] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.417120] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.417325] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.418764] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.419608] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.420370] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.420605] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.420744] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.420878] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.421465] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.421630] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [91.421639] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.421837] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.423160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.423283] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.423988] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.424490] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.424495] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.424617] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.449205] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.449209] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.449322] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.449639] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.451867] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [91.453174] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.477758] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.482009] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.482136] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.482266] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.482727] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.483368] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.483504] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.483682] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.483848] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.484430] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.484569] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [91.484604] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.484741] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.485206] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.485768] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.486283] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.487611] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.488608] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.489372] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.489531] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.489683] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.489817] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.490403] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.490545] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [91.490551] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.490687] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.491777] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.491896] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.492593] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.493095] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.493099] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.493214] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.518947] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.518951] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.519063] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.519202] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.520750] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [91.523413] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [91.586053] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [91.594224] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [91.605739] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.610551] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.610744] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.610914] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.611378] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.611986] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.612169] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.612335] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.612497] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.612624] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [91.613150] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.613353] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [91.613364] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.613558] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.614089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.614623] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.615164] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.616352] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.617493] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.618274] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.618438] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.618603] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.618743] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.619348] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.619509] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [91.619523] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.619713] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.620912] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.621053] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.621799] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.622291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.622295] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.622407] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.647579] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.647585] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.647728] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.647869] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.649121] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [91.651650] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.676087] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.680638] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.680795] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.680948] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.681403] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.682031] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.682192] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.682348] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.682498] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.682640] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.683123] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.683275] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [91.683283] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.683415] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.683900] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.684406] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.684978] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.686111] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.687219] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.687986] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.688150] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.688295] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.688434] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.689039] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.689190] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [91.689197] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.689327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.690438] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.690561] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.691271] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.691771] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.691775] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.691896] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.717610] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.717615] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.717740] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.717879] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.719372] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [91.721651] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.746103] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.750656] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.750809] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.750957] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.751408] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.752054] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.752211] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.752352] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.752489] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.753096] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.753250] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [91.753257] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.753385] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.753870] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.754373] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.754954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.756081] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.756870] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.757618] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.757778] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.757919] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.758055] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.758674] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.758829] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [91.758835] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.758962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.760073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.760195] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.760892] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.761373] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.761378] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.761496] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.786138] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.786143] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.786255] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.786394] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.787885] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [91.789251] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.865326] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.871661] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [91.872212] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.872560] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.873170] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.873371] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:DP-1] Same epoch counter 1
<7> [91.873370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.873383] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2]
<7> [91.873630] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.874141] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.874775] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<6> [91.875316] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [91.875975] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00
<7> [91.876956] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000
<7> [91.877622] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.877853] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.878055] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.878252] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.878918] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.879343] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:107:DP-2] Same epoch counter 1
<7> [91.879354] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [91.879539] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.880744] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.880922] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.881686] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.882156] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.882161] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.882281] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.906908] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.906913] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.907043] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.907192] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:113:HDMI-A-1] Same epoch counter 6
<7> [91.907396] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.907546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.908095] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [91.908756] [IGT] i915_pm_rpm: exiting, ret=0
<6> [91.909759] Console: switching to colour frame buffer device 128x48
Created at 2023-10-02 01:50:22