Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x79/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xec/0x2a0 [i915]
   pci_pm_runtime_suspend+0x5a/0x1a0
   __rpm_callback+0x3c/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.486s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.486s)
Dmesg
<7> [89.251047] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [89.251203] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [89.251325] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [89.251875] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [89.288220] Console: switching to colour dummy device 80x25
<6> [89.288275] [IGT] i915_pm_rpm: executing
<7> [89.290005] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [89.290439] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [89.290448] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [89.290578] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.291224] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [89.291332] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [89.291902] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [89.292431] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [89.292438] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.292552] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [89.308237] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [89.308242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [89.308354] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.308484] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [89.308536] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [89.308541] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [89.308655] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.309287] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.309394] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.309682] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.310102] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.310107] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.310224] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.324321] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.324326] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.324433] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.324561] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [89.324626] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [89.324631] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [89.324746] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.325182] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.325321] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [89.329370] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [89.329377] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [89.329499] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.330125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [89.330233] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [89.330803] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [89.331336] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [89.331342] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.331458] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [89.345623] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [89.345628] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [89.345736] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.345863] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [89.346418] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [89.346424] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [89.346539] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.347529] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.347643] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.347930] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.348353] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.348359] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.348472] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.363088] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.363093] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.363210] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.363335] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [89.363820] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [89.363825] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [89.363939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.364418] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.364554] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [89.364911] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [89.364916] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [89.365044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.365670] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [89.365778] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [89.366348] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [89.366867] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [89.366871] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.366975] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [89.381128] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [89.381133] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [89.381238] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.381362] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [89.381381] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [89.381386] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [89.381496] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.382514] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.382621] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [89.383209] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [89.383718] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.383722] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [89.383826] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [89.399553] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [89.399557] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [89.399662] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.399787] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [89.399806] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [89.399811] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [89.399923] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [89.400407] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [89.400542] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [90.405231] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.411107] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.415300] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.439924] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.450124] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.451557] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.451655] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.452475] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [90.452384] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.454183] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.454424] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.455187] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.455686] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.455695] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.455888] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.472251] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.472260] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.472431] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.473120] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.477414] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.477432] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.477665] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.482017] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.506650] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.514117] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.514677] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.514836] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.515536] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.515668] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.515981] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.516432] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.516441] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.516580] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.531209] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.531215] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.531333] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.531483] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [90.531497] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.531635] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.532204] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.532354] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [90.532372] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.532502] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.533626] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.533746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.534361] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.534842] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.534847] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.534962] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.550662] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.550667] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.550772] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.550907] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.552383] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.553549] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.554980] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.579351] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.588949] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.589425] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.589543] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.589673] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.590098] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.590715] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [90.590716] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.591064] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.591172] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.591460] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.591583] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.591588] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.591692] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.594503] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.594508] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.594620] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.594790] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.594913] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.595479] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.595618] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [90.595627] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.595763] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.596214] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.596366] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [90.596381] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.596500] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.597460] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.597575] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.598165] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.598673] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.598677] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.598781] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.613941] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.613946] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.614090] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.614241] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.614250] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.614369] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.614986] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.615110] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.615398] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.615802] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.615807] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.615912] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.631640] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.631645] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.631749] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.631883] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.632901] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [90.633296] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.637062] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.661472] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.667575] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.668177] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.668339] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.668460] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.668862] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.669592] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [90.669592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.669747] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.669892] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.670047] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.670622] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.670777] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [90.670795] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.670916] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.671890] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.672015] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.672585] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.673124] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.673129] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.673234] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.687830] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.687835] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.687939] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.688125] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.688135] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.688254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.688872] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.688979] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.689277] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.689682] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.689687] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.689791] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.705522] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.705527] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.705633] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.705766] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.706699] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [90.707177] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.710999] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.735367] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.739958] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.740470] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.740590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.740720] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.741143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.741740] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.741935] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.742142] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.742327] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.742949] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.743152] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [90.743168] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.743313] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.744297] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.744407] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.744976] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.745504] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.745509] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.745614] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.760750] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.760759] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.760946] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.761200] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.761209] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.761384] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.762418] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.762589] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.763240] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.763719] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.763726] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.763883] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.779093] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.779099] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.779211] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.779347] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [90.779354] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.779470] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.779891] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.780073] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [90.780081] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.781016] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.784836] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [90.843533] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [90.856188] [drm:drm_mode_setcrtc] [CRTC:51:pipe A]
<7> [90.868130] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.878130] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.879319] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.879619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.879957] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [90.880595] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [90.881487] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.881958] [drm:drm_mode_setcrtc] [CRTC:72:pipe B]
<7> [90.882108] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.882453] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.882957] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.883302] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.883314] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.883661] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.887133] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.887147] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.887440] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [90.887763] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [90.888119] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [90.888961] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.889707] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.889728] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [90.890070] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.891410] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.891743] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [90.892578] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [90.893230] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.893242] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.893570] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [90.909499] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [90.909507] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [90.909672] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.909882] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.910885] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.911899] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [90.911979] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [90.914800] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.939214] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [90.945691] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [90.946222] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [90.946386] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.946913] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.947290] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [90.947313] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [90.947524] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [90.948282] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.948479] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [90.949189] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [90.949687] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.949695] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [90.949889] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [90.965732] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [90.965740] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [90.965920] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [90.966161] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [90.966180] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [90.967198] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [90.970952] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [90.995936] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.006629] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.007466] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.007860] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.008341] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.009262] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.010291] [drm:drm_mode_setcrtc] [CRTC:93:pipe C]
<7> [91.010289] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.011231] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.011788] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.012665] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.013239] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.013256] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.013681] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.018502] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.018528] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.019175] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.019814] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.020431] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.021533] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.022277] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [91.022335] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.022941] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.023934] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.024631] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [91.024694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.025354] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.026986] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.027578] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.028713] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.029622] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.029645] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.030232] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.051665] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.051676] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.051931] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.052267] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.053334] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [91.053792] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.057306] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.081802] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.085978] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.086487] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.086598] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.086727] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.087150] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.087773] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.088203] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.088381] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.088767] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.088962] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.088970] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.089162] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.092270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.092279] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.092467] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.092669] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.092865] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.093513] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.093731] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [91.093741] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.093931] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.094446] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.094658] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [91.094676] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.094863] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.095999] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.096176] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.096544] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.097037] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.097044] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.097219] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.113000] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.113023] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.113200] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.113401] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.114398] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [91.114408] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.114867] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.118949] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.143458] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.149203] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.149751] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.149839] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.150858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.151034] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.151389] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.151853] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.151860] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.152036] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.167755] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.167762] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.167929] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.168188] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [91.168198] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.168375] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.168887] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.169123] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [91.169139] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.169314] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.170398] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.170563] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.170916] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.171395] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.171402] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.171565] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.186747] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.186752] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.186861] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.187010] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [91.187019] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.187138] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.187758] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.187865] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.188466] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.188940] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.188944] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.189065] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.203707] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.203712] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.203816] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.203946] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [91.203952] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.204124] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.204544] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.204674] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [91.204682] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [91.205647] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [91.209380] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [91.301048] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [91.320079] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [91.322698] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [91.323734] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [91.324829] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.325546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.326539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.328292] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<6> [91.329352] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [91.329239] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [91.330003] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [91.330163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.330170] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.330319] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [91.333229] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [91.333235] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [91.333348] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.333471] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.333591] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.334193] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.334473] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:95:HDMI-A-1] Same epoch counter 8
<7> [91.334481] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [91.334641] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.335306] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.335462] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [91.335763] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [91.336197] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.336204] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [91.336342] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [91.344715] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.345256] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [91.345780] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [91.346052] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [91.346907] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [91.346915] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [91.347057] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:105:HDMI-A-2] Same epoch counter 1
<7> [91.347064] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [91.347198] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:109:DP-1] Same epoch counter 1
<7> [91.359112] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [91.359283] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [91.359420] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [91.359552] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [91.360138] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [91.533507] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [91.533636] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [91.534062] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [91.534748] [IGT] i915_pm_rpm: exiting, ret=0
<6> [91.535855] Console: switching to colour frame buffer device 128x48
Created at 2023-10-02 01:50:22