Results for igt@i915_pm_rpm@basic-rte

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out 
Starting subtest: basic-rte
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x79/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xec/0x2a0 [i915]
   pci_pm_runtime_suspend+0x5a/0x1a0
   __rpm_callback+0x3c/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
Subtest basic-rte: SUCCESS (1.500s)
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 1
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x79/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   untrack_all_intel_runtime_pm_wakerefs+0x42/0x80 [i915]
   intel_runtime_suspend+0xec/0x2a0 [i915]
   pci_pm_runtime_suspend+0x5a/0x1a0
   __rpm_callback+0x3c/0x110
   rpm_callback+0x58/0x70
   rpm_suspend+0x118/0x5f0
   pm_runtime_work+0x9f/0xb0
Wakeref count: 1
Wakeref x1 taken at:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   __intel_display_power_put_async+0x3d/0x160 [i915]
   intel_atomic_commit_tail+0xa2e/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
Err 
Starting subtest: basic-rte
Subtest basic-rte: SUCCESS (1.500s)
Dmesg
<6> [70.946242] Console: switching to colour dummy device 80x25
<6> [70.946278] [IGT] i915_pm_rpm: executing
<6> [70.958293] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [70.958345] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [70.958824] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-1]
<7> [70.958832] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [70.958968] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.959665] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.959827] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-1] disconnected
<7> [70.959894] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:145:HDMI-A-1]
<7> [70.959898] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [70.960027] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.960832] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.960990] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:145:HDMI-A-1] disconnected
<7> [70.961047] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:151:DP-2]
<7> [70.961051] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [70.961191] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.962049] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.962225] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:151:DP-2] disconnected
<7> [70.962287] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:157:HDMI-A-2]
<7> [70.962293] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [70.962447] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.963224] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.963424] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:157:HDMI-A-2] disconnected
<7> [70.963498] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:161:DP-3]
<7> [70.963504] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [70.963678] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.964443] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.964650] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:161:DP-3] disconnected
<7> [70.964726] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:167:HDMI-A-3]
<7> [70.964745] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [70.964929] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.965720] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.965985] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:167:HDMI-A-3] disconnected
<7> [70.966080] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:171:DP-4]
<7> [70.966087] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [70.966294] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.967110] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.967364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:171:DP-4] disconnected
<7> [70.967454] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:177:HDMI-A-4]
<7> [70.967460] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [70.967653] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.968497] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.968710] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:177:HDMI-A-4] disconnected
<7> [70.973509] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-1]
<7> [70.973516] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [70.973660] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.974361] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.974486] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-1] disconnected
<7> [70.974852] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:145:HDMI-A-1]
<7> [70.974855] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [70.974957] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.975626] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.975747] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:145:HDMI-A-1] disconnected
<7> [70.976044] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:151:DP-2]
<7> [70.976047] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [70.976140] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.976787] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.976879] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:151:DP-2] disconnected
<7> [70.977156] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:157:HDMI-A-2]
<7> [70.977159] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [70.977235] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.977945] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.978040] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:157:HDMI-A-2] disconnected
<7> [70.978311] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:161:DP-3]
<7> [70.978313] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [70.978394] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.979102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.979191] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:161:DP-3] disconnected
<7> [70.979462] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:167:HDMI-A-3]
<7> [70.979465] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [70.979543] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.980262] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.980354] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:167:HDMI-A-3] disconnected
<7> [70.980624] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:171:DP-4]
<7> [70.980626] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [70.980704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.981402] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.981491] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:171:DP-4] disconnected
<7> [70.981759] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:177:HDMI-A-4]
<7> [70.981762] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [70.981840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.982560] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.982646] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:177:HDMI-A-4] disconnected
<7> [70.982917] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-1]
<7> [70.982919] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [70.982997] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.983716] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.983825] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:134:DP-1] disconnected
<7> [70.983834] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:145:HDMI-A-1]
<7> [70.983837] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [70.983915] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.984877] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.984968] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:145:HDMI-A-1] disconnected
<7> [70.984978] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:151:DP-2]
<7> [70.984980] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [70.985060] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.986027] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.986117] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:151:DP-2] disconnected
<7> [70.986126] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:157:HDMI-A-2]
<7> [70.986128] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [70.986201] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.987185] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.987277] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:157:HDMI-A-2] disconnected
<7> [70.987286] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:161:DP-3]
<7> [70.987289] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [70.987367] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.988341] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.988434] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:161:DP-3] disconnected
<7> [70.988443] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:167:HDMI-A-3]
<7> [70.988445] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [70.988522] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.989492] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.989583] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:167:HDMI-A-3] disconnected
<7> [70.989593] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:171:DP-4]
<7> [70.989595] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [70.989677] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.990647] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.990743] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:171:DP-4] disconnected
<7> [70.990752] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:177:HDMI-A-4]
<7> [70.990754] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [70.990833] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [70.991814] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [70.991907] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:177:HDMI-A-4] disconnected
<7> [71.993185] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [71.996447] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.001087] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.002202] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.002318] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.002424] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.002524] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.002622] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.002718] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.002831] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.002934] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.003033] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.003129] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.003243] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.003401] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.003545] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.003678] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.003775] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.003906] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.030000] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.030358] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.030947] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.031448] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.032478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.033089] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.033522] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.034849] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.035310] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.037458] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.037878] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.050944] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.053198] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.054343] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.055543] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [72.055563] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.056676] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.056851] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.056857] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.056940] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.057840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.057977] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.057981] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.058080] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.058986] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.059096] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.059100] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.059179] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.060165] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.060258] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.060272] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.062467] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.064791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.065922] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.066030] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.066133] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.066236] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.066341] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.066443] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.066544] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.066647] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.066756] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.066859] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.066976] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.067164] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.067308] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.067439] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.067527] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.067639] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.092235] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.092415] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.092714] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.093095] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.093790] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.094146] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.094465] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.094932] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.095296] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.097062] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.097418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.110454] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.112703] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.112803] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.112915] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.113858] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.113975] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.114087] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.114196] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.114304] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.114410] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.114515] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.114620] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.114735] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.114845] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.114952] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.115094] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [72.115138] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.115285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.115385] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.115476] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.116644] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.116780] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.116786] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.116865] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.117818] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.117922] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.117928] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.118009] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.118961] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.119058] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.119062] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.119141] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.120120] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.120217] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.120230] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.122444] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.124795] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.125897] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.126022] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.126139] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.126256] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.126368] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.126478] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.126585] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.126696] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.126815] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.126925] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.127056] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.127243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.127388] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.127518] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.127609] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.127721] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.152431] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.152704] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.153251] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.153754] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.154606] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.155142] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.155582] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.156205] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.156674] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.158828] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.159253] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.173493] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.175756] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.175832] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.175944] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.176894] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.177014] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.177126] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.177233] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.177339] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.177447] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.177554] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.177659] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.177772] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.177878] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.177987] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.178105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.178243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.178342] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.178432] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.179598] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.179699] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.179703] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.179799] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.180767] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.180858] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.180861] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.180942] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.181915] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.182008] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.182011] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.182089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.183078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.183171] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.183174] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.183256] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.184226] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.184332] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.184335] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.184424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.185386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.185499] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.185502] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.185599] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.186543] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.186680] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.186684] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.186813] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.187697] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.187860] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.187871] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.187988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.188850] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.188979] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.188983] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.189092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.190006] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.190117] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.190120] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.190218] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.191170] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.191269] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.191272] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.191355] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.192315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.192409] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.192412] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.192491] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.193466] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.193556] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.193558] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.193634] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.194629] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.194722] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.194725] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.194815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.195777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.195870] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.195873] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.195951] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.196940] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.197030] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.197034] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.199266] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.201586] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.202713] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.202843] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.202947] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.203051] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.203153] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.203254] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.203354] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.203457] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.203556] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.203656] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.203781] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.203964] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.204108] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.204238] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.204331] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.204443] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.278946] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [72.290967] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.291283] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.291798] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.292278] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.293161] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.293668] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.294154] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.294700] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.295207] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.297314] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.297468] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.309207] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.311481] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.311570] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.311683] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.312594] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.312712] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.312834] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.312943] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.313049] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.313154] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.313258] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.313361] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.313471] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.313578] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.313683] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.313838] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.313966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.314075] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.314168] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.314796] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [72.315336] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.315435] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.315442] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.315530] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.316502] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.316598] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.316604] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.316691] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.317644] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.317746] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.317749] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.317833] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.318808] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.318908] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.318967] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.319069] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.319945] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.321123] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.321234] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.321338] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.321439] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.321540] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.321640] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.321746] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.321849] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.321949] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.322049] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.322190] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.322293] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.322391] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.322482] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.323640] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.323740] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.323743] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.323823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.324812] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.324909] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.324912] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.324999] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.325967] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.326062] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.326065] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.326148] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.327123] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.327222] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.327226] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.329454] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.331764] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.332903] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.333015] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.333123] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.333230] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.333342] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.333449] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.333554] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.333664] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.333779] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.333884] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.334005] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.334196] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.334344] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.334487] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.334581] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.334699] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.435467] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.435860] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.436306] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.436793] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.437604] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.438873] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.439295] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.439828] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.440278] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.442095] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.442178] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.453930] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.456204] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.457335] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.457494] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<6> [72.458618] [IGT] i915_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [72.458637] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [72.459665] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.459797] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.459802] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.459888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.460828] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.460924] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.460929] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.461009] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.461974] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.462068] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.462071] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.462150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.463130] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.463223] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.463233] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.465417] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.467747] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.468906] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.469014] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.469116] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.469220] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.469321] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.469422] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.469521] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.469623] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.469721] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.469834] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.469950] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.470136] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.470283] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.470416] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.470505] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.470618] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.494302] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.494487] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.494827] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.495143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.495825] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.496191] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.496503] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.497020] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.497380] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.499186] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.499528] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.512573] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.514820] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.514907] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.515009] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.515979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.517160] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.517272] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.517377] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.517479] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.517581] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.517682] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.517803] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.517916] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.518023] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.518129] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.518249] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [72.518342] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.518473] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.518580] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.518675] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.519857] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.519960] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.519965] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.520047] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.521036] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.521128] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.521131] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.521210] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.522185] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.522278] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.522282] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.522363] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.523343] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.523436] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.523449] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.525667] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.527985] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.529121] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.529246] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.529359] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.529472] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.529584] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.529693] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.529825] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.529939] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.530050] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.530159] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.530278] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.530464] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.530605] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.530744] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.530832] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.530943] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.554385] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.554659] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.555199] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.555673] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.556556] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.557080] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.557517] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.558123] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.558593] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.560706] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.561163] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.575413] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.577650] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.577726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.577848] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.578812] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.579986] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.580097] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.580203] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.580311] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.580419] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.580527] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.580634] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.580753] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.580860] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.580965] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.581100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.581243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.581348] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.581443] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.582613] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.582711] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.582716] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.582833] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.583778] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.583874] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.583877] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.583956] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.584932] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.585024] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.585028] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.585109] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.586089] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.586180] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.586183] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.586260] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.587242] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.587333] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.587335] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.587410] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.588400] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.588500] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.588503] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.588588] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.589551] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.589665] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.589669] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.589776] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.590705] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.590844] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.590854] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.590966] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.591868] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.591998] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.592002] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.592105] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.593036] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.593145] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.593148] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.593241] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.594172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.594270] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.594273] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.594353] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.595332] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.595423] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.595426] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.595501] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.596486] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.596579] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.596581] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.596658] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.597631] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.597722] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.597725] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.597818] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.598789] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.598880] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.598882] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.598958] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.599951] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.600041] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.600046] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [72.602281] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [72.604614] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.605733] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.605846] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.605954] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.606056] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.606159] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.606260] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.606364] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.606468] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.606571] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.606674] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.606803] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [72.606984] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [72.607126] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.607256] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [72.607343] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [72.607458] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [72.709470] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [72.709877] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [72.710340] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [72.710857] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [72.711785] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [72.712979] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [72.713425] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [72.714024] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [72.714526] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [72.716692] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.717147] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.735953] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [72.740568] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:134:DP-1]
<7> [72.741713] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [72.741869] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.742891] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.743008] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:134:DP-1] Same epoch counter 1
<7> [72.743014] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:145:HDMI-A-1]
<7> [72.743008] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.743127] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.744026] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.744147] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.744256] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.744360] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.744462] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.744564] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.744666] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.744781] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.744888] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.744990] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.745092] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [72.745179] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [72.745272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [72.745401] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:145:HDMI-A-1] Same epoch counter 8
<7> [72.745374] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [72.745404] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:151:DP-2]
<7> [72.745512] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:151:DP-2] Same epoch counter 1
<7> [72.745515] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:157:HDMI-A-2]
<7> [72.745629] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:157:HDMI-A-2] Same epoch counter 1
<7> [72.745632] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:161:DP-3]
<7> [72.745760] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:161:DP-3] Same epoch counter 1
<7> [72.745763] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:167:HDMI-A-3]
<7> [72.745880] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:167:HDMI-A-3] Same epoch counter 1
<7> [72.745883] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:171:DP-4]
<7> [72.745985] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:171:DP-4] Same epoch counter 1
<7> [72.745988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:177:HDMI-A-4]
<7> [72.746092] i915 0000:00:02.0: [drm:check_connector_changed] [CONNECTOR:177:HDMI-A-4] Same epoch counter 1
<7> [72.757524] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [72.757702] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [72.757832] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [72.757949] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [72.758060] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [72.759242] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [72.798992] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [72.799443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [72.800497] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [72.801712] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.802215] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [72.802648] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.803135] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [72.803568] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.804027] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [72.804444] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.804895] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [72.805307] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [72.805719] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<6> [72.806536] [IGT] i915_pm_rpm: exiting, ret=0
<6> [72.809200] Console: switching to colour frame buffer device 128x48
Created at 2023-10-02 01:50:22