Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.559s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.559s)
Dmesg
<6> [155.895035] Console: switching to colour dummy device 80x25
<6> [155.895229] [IGT] kms_force_connector_basic: executing
<7> [155.898056] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [155.898748] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [155.898918] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [155.899403] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [155.899409] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [155.899415] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [155.951048] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [155.968145] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [155.968153] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [155.968277] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [155.985163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [155.985167] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [155.985265] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [155.985307] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [155.985313] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.036050] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.053164] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.053169] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.053272] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.069175] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.069178] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.069275] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [156.069328] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.069333] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.080031] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [156.080204] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [156.091034] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [156.091317] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [156.142072] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.159179] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.159184] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.159308] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.176154] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.176158] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.176254] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [156.176452] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [156.176552] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [156.176556] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.176560] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.227048] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.244193] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.244203] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.244329] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.261177] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.261184] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.261280] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] status updated from disconnected to connected
<7> [156.261389] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [156.261393] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [156.261398] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [156.261402] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [156.261406] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [156.261410] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [156.261443] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.261449] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.311939] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.329159] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.329169] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.329285] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.346157] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.346164] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.346291] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [156.346295] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [156.346299] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [156.346302] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [156.346305] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [156.346308] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [156.346469] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [156.346484] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.346488] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.346602] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [156.346606] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [156.397059] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.414142] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [156.414211] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [156.414216] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [156.414220] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [156.414223] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [156.414226] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [156.414229] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [156.414232] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [156.414235] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [156.414238] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [156.414241] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [156.414243] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [156.414351] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [156.414370] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.414374] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.414506] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [156.414510] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [156.414513] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 4
<7> [156.465049] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.482188] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [156.482251] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [156.482256] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [156.482260] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [156.482263] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [156.482266] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [156.482270] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [156.482272] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [156.482275] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [156.482376] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [156.482395] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.482399] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.533042] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.550160] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.550168] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.550280] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.567143] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.567149] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.567244] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 5
<7> [156.567284] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [156.567289] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [156.567293] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [156.567297] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [156.567301] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [156.567304] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [156.567308] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [156.567311] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [156.567314] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [156.567318] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [156.567431] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [156.567436] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.567441] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.618045] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.635156] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.635161] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.635262] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.651142] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.651146] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.651246] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] status updated from connected to disconnected
<7> [156.651256] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [156.651354] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.651360] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.702047] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.719135] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.719140] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.719248] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.735158] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.735161] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.735257] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [156.735477] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [156.735581] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [156.735974] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [156.735979] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]
<7> [156.735984] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [156.736815] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00 00
<7> [156.736943] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [156.737594] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [156.737699] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [156.737798] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [156.737907] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [156.738020] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [156.738024] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [156.738028] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [156.738031] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [156.738043] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [156.738137] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [156.738879] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [156.738983] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [156.739660] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :
<7> [156.739665] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [156.739670] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [156.739693] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]
<7> [156.739697] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [156.740517] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00 00
<7> [156.740620] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [156.741229] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [156.741326] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [156.741421] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [156.741517] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [156.741626] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [156.741630] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [156.741633] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [156.741635] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [156.741645] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [156.741739] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [156.742522] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [156.742619] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [156.743269] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :
<7> [156.743273] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [156.743276] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [156.743354] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:eDP-1] EDID override reset
<7> [156.743368] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]
<7> [156.743372] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [156.744171] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00 00
<7> [156.744273] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [156.744868] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [156.744964] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [156.745060] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [156.745157] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [156.745266] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [156.745270] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [156.745273] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [156.745276] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [156.745286] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [156.745380] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [156.746195] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [156.746299] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [156.746947] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :
<7> [156.746951] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [156.746955] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [156.747041] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:246:DP-1] EDID override reset
<7> [156.747056] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
<7> [156.747060] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [156.747210] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
<7> [156.747300] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [156.747304] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.747308] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.798053] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.815206] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.815211] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.815321] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.832163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.832167] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.832265] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [156.832306] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.832311] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.883047] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.900144] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.900148] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.900250] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [156.916205] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.916209] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [156.916305] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [156.916391] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [156.916406] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [156.916410] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [156.967043] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [156.984171] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [156.984176] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [156.984279] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [157.001178] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [157.001182] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [157.001279] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [157.001394] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-2] EDID override reset
<7> [157.001407] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2]
<7> [157.001410] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [157.001550] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2] disconnected
<7> [157.001616] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:273:DP-3] EDID override reset
<7> [157.001627] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3]
<7> [157.001631] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [157.001776] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3] disconnected
<6> [157.002119] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [157.002195] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [157.002199] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [157.002203] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [157.053047] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [157.070152] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [157.070157] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [157.070260] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [157.086185] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [157.086189] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [157.086287] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [157.086338] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [157.086344] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]
<7> [157.086349] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [157.087222] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00 00
<7> [157.087329] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [157.087960] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [157.088059] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [157.088155] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [157.088250] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [157.088358] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [157.088363] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [157.088366] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [157.088369] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [157.088381] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [157.088481] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [157.089290] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [157.089386] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [157.090079] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :
<7> [157.090083] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [157.090087] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [157.090246] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [157.091401] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [157.091406] [drm:drm_client_modeset_probe]
<7> [157.091433] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]
<7> [157.091438] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [157.092272] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00 00
<7> [157.092381] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [157.093015] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [157.093117] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [157.093216] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [157.093312] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [157.093422] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [157.093426] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [157.093430] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [157.093433] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [157.093444] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [157.093544] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [157.094308] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [157.094404] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [157.095084] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :
<7> [157.095088] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [157.095092] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [157.095096] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
<7> [157.095099] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [157.095249] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
<7> [157.095253] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [157.095256] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [157.146068] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [157.163202] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [157.163206] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [157.163314] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [157.180191] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [157.180195] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [157.180292] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [157.180296] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2]
<7> [157.180300] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [157.180437] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2] disconnected
<7> [157.180440] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3]
<7> [157.180444] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [157.180578] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3] disconnected
<7> [157.180582] [drm:drm_client_modeset_probe] connector 236 enabled? yes
<7> [157.180586] [drm:drm_client_modeset_probe] connector 246 enabled? no
<7> [157.180588] [drm:drm_client_modeset_probe] connector 258 enabled? no
<7> [157.180590] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [157.180592] [drm:drm_client_modeset_probe] connector 273 enabled? no
<7> [157.180616] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [157.180624] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 236
<7> [157.180628] [drm:drm_client_modeset_probe] looking for preferred mode on connector 236 0
<7> [157.180631] [drm:drm_client_modeset_probe] found mode 1920x1080
<7> [157.180633] [drm:drm_client_modeset_probe] picking CRTCs for 1920x1080 config
<7> [157.180646] [drm:drm_client_modeset_probe] desired mode 1920x1080 set on crtc 80 (0,0)
<6> [157.208551] Console: switching to colour frame buffer device 240x67
Created at 2023-10-02 01:50:22