igt@i915_module_load@load on bat-jsl-1@linus-v6.6-rc4 Test details

Detail	Value
Igt-Version	IGT-Version: 1.28-g8abfd4fd5 (x86_64) (Linux: 6.6.0-rc4-linus-v6.6-rc4-g8a749fd1a872+ x86_64)
Out	Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (2.525s)
Err	Starting subtest: load Subtest load: SUCCESS (2.525s)
Dmesg	<6> [40.359554] Console: switching to colour dummy device 80x25 <6> [40.359976] [IGT] i915_module_load: executing <6> [40.372014] [IGT] i915_module_load: starting subtest load <4> [40.952070] <4> [40.952088] ******************************************************** <4> [40.952092] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [40.952095] <4> [40.952098] trace_printk() being used. Allocating extra memory. <4> [40.952101] <4> [40.952104] This means that this is a DEBUG kernel and it is <4> [40.952107] unsafe for production use. <4> [40.952110] <4> [40.952112] If you see this message and you are not debugging <4> [40.952115] the kernel, report this immediately to your vendor! <4> [40.952118] <4> [40.952121] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [40.952123] ******************************************************** <7> [41.043886] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K <7> [41.044375] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no) <7> [41.044807] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH <7> [41.045246] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [41.045929] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [41.046307] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz <7> [41.047326] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001 <7> [41.047662] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001 <7> [41.048859] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [41.049190] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [41.049490] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M <6> [41.049819] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [41.058669] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [41.059448] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [41.059488] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7 <7> [41.060346] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K <7> [41.061266] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018 <7> [41.061730] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0 <7> [41.062107] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [41.062474] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [41.062858] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [41.074303] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583 <7> [41.074859] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [41.075245] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [41.075634] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [41.076013] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [41.076328] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no <7> [41.077119] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [41.077436] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no <7> [41.077761] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no <7> [41.078060] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [41.078357] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no <7> [41.079579] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [41.080008] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [41.080306] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [41.080618] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50 <7> [41.081013] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68 <7> [41.081392] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56 <7> [41.081785] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834 <7> [41.082153] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941 <7> [41.082515] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878 <7> [41.082900] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899 <7> [41.083265] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488 <7> [41.083634] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583 <7> [41.084002] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069 <7> [41.084364] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719 <7> [41.084733] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483 <7> [41.085098] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280 <7> [41.085459] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000 <7> [41.085836] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000 <7> [41.086196] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000 <7> [41.086553] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000 <7> [41.086972] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000 <7> [41.087339] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000 <7> [41.087719] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000 <7> [41.088078] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000 <7> [41.089276] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [41.089930] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228 <7> [41.090314] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [41.090700] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5) <7> [41.091092] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [41.091465] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [41.091853] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812) <7> [41.092221] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34) <7> [41.092588] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [41.092979] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366) <7> [41.093345] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [41.093731] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78) <7> [41.094105] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822) <7> [41.094459] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [41.094829] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [41.095200] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806 <7> [41.095565] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [41.096154] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [41.096529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [41.096903] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [41.097263] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [41.097635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000 <7> [41.098001] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [41.098355] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0 <7> [41.098721] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000 <7> [41.099085] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [41.099441] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0 <7> [41.099807] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000 <7> [41.100168] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a <7> [41.100559] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [41.100972] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [41.101353] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [41.101791] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [41.102168] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [41.102521] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [41.102912] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [41.103355] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [41.103796] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 556800 kHz, VCO 1113600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 3 <7> [41.104168] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [41.104683] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.105050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [41.105411] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [41.105829] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [41.106205] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [41.106568] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [41.106956] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [41.107320] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [41.107706] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [41.108065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [41.108438] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <6> [41.108848] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [41.108967] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [41.109476] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin <7> [41.112968] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [41.114018] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us <7> [41.114439] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [41.114866] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [41.115245] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [41.115640] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <6> [41.116095] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9) <7> [41.116007] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [41.116361] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [41.116765] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [41.117122] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [41.125712] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [41.131654] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 556800 kHz, VCO 1113600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 3 <7> [41.132457] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <6> [41.133200] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <7> [41.133569] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz <7> [41.133979] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz <7> [41.134420] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT) <7> [41.134853] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A] <7> [41.142633] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0) <7> [41.143084] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [41.143480] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [41.143896] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless <7> [41.144305] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [41.144716] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [41.145104] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002 <7> [41.145484] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [41.147131] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [41.147555] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7> [41.148236] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0 <7> [41.148710] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000 <7> [41.149075] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [41.149432] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [41.150153] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [41.150519] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [41.151010] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [41.151639] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [41.152265] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [41.152752] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [41.154388] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [41.155138] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001 <7> [41.155711] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6 <7> [41.156797] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1 <7> [41.161991] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.163649] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.165517] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.167407] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.169269] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.170811] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.172645] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.174545] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [41.175925] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [41.175955] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [41.175963] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [41.176096] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [41.176513] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa <7> [41.176920] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms) <7> [41.190330] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none <7> [41.190907] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0) <7> [41.191291] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, enabled, brightness 96000/96000 <7> [41.191789] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000 <7> [41.192142] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [41.192494] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [41.192855] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [41.193201] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [41.193669] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [41.194532] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT) <7> [41.194947] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B] <7> [41.195743] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [41.196115] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B] <7> [41.196458] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT) <7> [41.197088] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C] <7> [41.197431] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT) <7> [41.198671] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: enabled <7> [41.199189] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled <7> [41.199683] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled <7> [41.200053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: enabled, pipe A <7> [41.200420] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A <7> [41.200809] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A <7> [41.201174] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A <7> [41.201536] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A <7> [41.201922] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A <7> [41.202288] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A <7> [41.202673] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A <7> [41.203042] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B <7> [41.203395] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B <7> [41.203777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B <7> [41.204150] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B <7> [41.204526] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B <7> [41.204913] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B <7> [41.205278] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B <7> [41.205665] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B <7> [41.206037] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C <7> [41.206394] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C <7> [41.206767] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C <7> [41.207148] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C <7> [41.207523] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C <7> [41.207911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C <7> [41.208271] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C <7> [41.208650] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C <7> [41.209069] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0 <7> [41.209556] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: enabled, pipe A <7> [41.209954] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A <7> [41.210316] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A <7> [41.210685] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B <7> [41.211032] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C <7> [41.211392] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A <7> [41.211785] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0 <7> [41.212143] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1 <7> [41.212509] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [41.212903] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0 <7> [41.213473] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: enabled <7> [41.213911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled <7> [41.214289] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled <7> [41.214685] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled <7> [41.215295] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 181030 kHz <7> [41.215686] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz <7> [41.216038] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz <7> [41.216377] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz <7> [41.216735] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz <7> [41.217087] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz <7> [41.217430] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz <7> [41.217791] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz <7> [41.218143] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 1448240 num active planes 1 <7> [41.218510] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz <7> [41.218876] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz <7> [41.219222] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz <7> [41.219567] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz <7> [41.219930] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz <7> [41.220272] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz <7> [41.220630] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz <7> [41.220979] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz <7> [41.221319] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [41.221696] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz <7> [41.222048] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz <7> [41.222391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz <7> [41.222752] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz <7> [41.223097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz <7> [41.223442] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz <7> [41.223802] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz <7> [41.224146] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz <7> [41.224491] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [41.224903] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [41.247803] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [setup_hw_state] <7> [41.248285] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [41.248781] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 18, dithering: 0 <7> [41.249226] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [41.249578] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [41.249952] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [41.250307] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [41.250678] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 3157174, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64 <7> [41.251040] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [41.251385] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [41.251748] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [41.252107] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [41.252452] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [41.252814] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [41.253172] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=362060, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [41.253520] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [41.253885] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=362060, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [41.254242] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 541120, pipe src: 3200x1800+0+0, pixel rate 362060 <7> [41.254591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0 <7> [41.254959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [41.255312] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [41.255683] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [41.256042] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [41.256404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [41.256768] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [41.257126] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [41.257475] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.257875] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.258229] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.258580] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [41.258950] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [41.259303] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.259671] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.260029] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.260371] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [41.260736] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state] <7> [41.261093] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state] <7> [41.261656] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x1, ddb (0 - 682), active pipes 0x1, mbus joined: no <7> [41.262020] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [41.262375] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [41.263346] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] pipe A/plane 1A with fb: size=3200x1800@32, offset=0, pitch 12800, size 0x15f9000 <7> [41.263767] i915 0000:00:02.0: [drm:_i915_gem_object_stolen_init [i915]] creating preallocated stolen object: stolen_offset=0x0000000000000000, size=0x00000000015f9000 <7> [41.266821] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[15f9000, 15fb000] for use by error capture <7> [41.267166] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [15fb000, 100000000] <7> [41.267498] MCR Steering: Default steering: group=0x0, instance=0x0 <7> [41.267522] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global <7> [41.268996] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0 <7> [41.269392] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0 <7> [41.269790] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0 <7> [41.272279] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0 <7> [41.273591] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0 <7> [41.274834] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0 <7> [41.290149] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate <7> [41.290588] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [41.291428] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate <7> [41.291854] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [41.292284] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate <7> [41.292678] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [41.293180] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [41.293589] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz <7> [41.293973] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24 <7> [41.294330] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000 <7> [41.294704] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no <7> [41.295059] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long <7> [41.295414] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [41.295806] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A] <7> [41.296165] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 3157174/8388608 link 350797/524288, found tu 64, data 4209566/8388608 link 350797/524288) <7> [41.296539] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x01c001a5, found 0x00e001a5) <7> [41.296931] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 18, found 24) <7> [41.297305] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 362060, found 361310) <7> [41.297695] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 362060, found 361310) <7> [41.298070] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 541120, found 540000) <7> [41.298441] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [41.298825] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0 <7> [41.299246] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no <7> [41.299631] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 682) -> (0 - 1024), active pipes 0x1 -> 0x1 <7> [41.300234] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate <7> [41.300593] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [41.301061] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [41.301457] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz <7> [41.301833] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24 <7> [41.302186] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000 <7> [41.302537] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no <7> [41.302940] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long <7> [41.303340] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [41.303759] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A] <7> [41.304114] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 3157174/8388608 link 350797/524288, found tu 64, data 4209566/8388608 link 350797/524288) <7> [41.304486] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x01c001a5, found 0x00e001a5) <7> [41.304871] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 18, found 24) <7> [41.305238] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 362060, found 361310) <7> [41.305617] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 362060, found 361310) <7> [41.305988] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 541120, found 540000) <7> [41.306352] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [41.306725] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0 <7> [41.307128] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no <7> [41.307489] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 682) -> (0 - 1024), active pipes 0x1 -> 0x1 <7> [41.307967] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 682) -> ( 0 - 985), size 682 -> 985 <7> [41.308328] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39 <7> [41.308699] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7, twm, swm, stwm <7> [41.309058] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [41.309408] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 27, 27, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 0, 0, 0 <7> [41.309774] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 0, 0, 0 <7> [41.310133] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.310479] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.310918] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.311274] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.311651] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.312003] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.312347] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.312719] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.313079] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.313426] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.313791] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.314146] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.314491] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.314853] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.315207] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.315561] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.315928] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.316273] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.316644] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.316998] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.317338] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.317700] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.318054] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.318396] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.318755] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [41.319110] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.319460] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.319830] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [41.320186] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1 <7> [41.320549] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [41.320928] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446 <7> [41.321300] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446 <7> [41.321752] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz) <7> [41.322121] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [41.322480] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz <7> [41.322864] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1 <7> [41.323232] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0 <7> [41.323586] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0 <7> [41.323977] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset] <7> [41.324346] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [41.324718] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [41.325081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [41.325433] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [41.325803] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [41.326163] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [41.326522] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64 <7> [41.326909] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [41.327271] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [41.327643] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [41.328005] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [41.328359] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [41.328749] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [41.329113] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [41.329471] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [41.329843] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [41.330203] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310 <7> [41.330559] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0 <7> [41.330935] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [41.331293] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [41.331665] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [41.332025] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [41.332378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [41.332746] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [41.333109] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [41.333459] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.333823] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.334183] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.334540] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [41.334914] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [41.335268] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.335636] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.335996] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [41.336344] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [41.336708] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:267] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [41.337072] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [41.337422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0 <7> [41.337799] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [41.338159] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [41.338512] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [41.338882] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [41.339240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [41.339594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [41.339968] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [41.346681] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [41.550097] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0 <7> [41.553022] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [41.572867] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off <7> [41.573880] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time <7> [41.574827] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [41.626691] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [41.627751] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [41.629793] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A] <7> [41.631228] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [41.632266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [41.633367] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1 <7> [41.635152] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [41.636188] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [41.637171] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [41.638102] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [41.639026] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [41.639959] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [41.640912] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [41.641878] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [41.642863] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [41.643805] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3 <7> [41.644840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [41.645840] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A] <7> [41.646771] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [41.649528] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on <7> [41.650520] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [42.246144] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [42.247169] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [42.248102] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on <7> [42.249036] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [42.459717] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [42.460816] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [42.462344] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [42.463516] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [42.466975] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [42.467092] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14 <7> [42.468505] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [42.469048] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [42.470555] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0 <7> [42.471021] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0 <7> [42.472760] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK <7> [42.473160] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [42.475228] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1 <7> [42.475705] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1 <7> [42.477943] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [42.478315] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4 <7> [42.479060] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [42.479838] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [42.480202] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [42.480587] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000 <7> [42.484494] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [42.484931] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A] <7> [42.497232] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [42.498014] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [42.498404] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [42.499407] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0 <7> [42.499877] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7> [42.500362] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [42.501361] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] found possible fb from [PLANE:31:plane 1A] <7> [42.501846] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping <7> [42.502194] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping <7> [42.502542] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] checking [PLANE:31:plane 1A] for BIOS fb <7> [42.502916] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] area: 3200x1800, bpp: 32, size: 23040000 <7> [42.503271] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] fb big enough [PLANE:31:plane 1A] (23040000 >= 23040000) <7> [42.503628] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping <7> [42.503982] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping <7> [42.504329] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] using BIOS fb for initial console <7> [42.504727] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [42.506223] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [42.506560] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [42.506885] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [42.507200] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [42.519272] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered <7> [42.519946] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7> [42.522420] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event <7> [42.523370] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1 <7> [42.525661] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event <7> [42.526427] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event <7> [42.527180] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event <6> [42.527281] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [42.531777] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <6> [42.566292] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [42.574957] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4 <7> [42.579284] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x4810 (init value 0x4810) <6> [42.579924] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [42.582367] [drm:drm_client_modeset_probe] <7> [42.582931] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] <7> [42.582977] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [42.584473] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [42.584954] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11 <7> [42.584962] i915 device info: graphics version: 11 <7> [42.584966] i915 device info: media version: 11 <7> [42.584970] i915 device info: graphics stepping: B0 <7> [42.584974] i915 device info: media stepping: B0 <7> [42.584977] i915 device info: display stepping: B0 <7> [42.584981] i915 device info: base die stepping: * <7> [42.584984] i915 device info: gt: 0 <7> [42.584987] i915 device info: memory-regions: 0x21 <7> [42.584991] i915 device info: page-sizes: 0x211000 <7> [42.584994] i915 device info: platform: JASPERLAKE <7> [42.584998] i915 device info: ppgtt-size: 36 <7> [42.585001] i915 device info: ppgtt-type: 2 <7> [42.585005] i915 device info: dma_mask_size: 39 <7> [42.585008] i915 device info: is_mobile: no <7> [42.585012] i915 device info: is_lp: no <7> [42.585015] i915 device info: require_force_probe: no <7> [42.585019] i915 device info: is_dgfx: no <7> [42.585022] i915 device info: has_64bit_reloc: yes <7> [42.585025] i915 device info: has_64k_pages: no <7> [42.585029] i915 device info: gpu_reset_clobbers_display: no <7> [42.585032] i915 device info: has_reset_engine: yes <7> [42.585035] i915 device info: has_3d_pipeline: yes <7> [42.585039] i915 device info: has_4tile: no <7> [42.585042] i915 device info: has_flat_ccs: no <7> [42.585045] i915 device info: has_global_mocs: no <7> [42.585049] i915 device info: has_gmd_id: no <7> [42.585052] i915 device info: has_gt_uc: yes <7> [42.585055] i915 device info: has_heci_pxp: no <7> [42.585058] i915 device info: has_heci_gscfi: no <7> [42.585062] i915 device info: has_guc_deprivilege: no <7> [42.585065] i915 device info: has_l3_ccs_read: no <7> [42.585068] i915 device info: has_l3_dpf: no <7> [42.585071] i915 device info: has_llc: yes <7> [42.585075] i915 device info: has_logical_ring_contexts: yes <7> [42.585078] i915 device info: has_logical_ring_elsq: yes <7> [42.585081] i915 device info: has_media_ratio_mode: no <7> [42.585085] i915 device info: has_mslice_steering: no <7> [42.585088] i915 device info: has_oa_bpc_reporting: no <7> [42.585091] i915 device info: has_oa_slice_contrib_limits: no <7> [42.585094] i915 device info: has_oam: no <7> [42.585097] i915 device info: has_one_eu_per_fuse_bit: no <7> [42.585100] i915 device info: has_pxp: no <7> [42.585103] i915 device info: has_rc6: yes <7> [42.585107] i915 device info: has_rc6p: no <7> [42.585110] i915 device info: has_rps: yes <7> [42.585113] i915 device info: has_runtime_pm: yes <7> [42.585116] i915 device info: has_snoop: no <7> [42.585119] i915 device info: has_coherent_ggtt: no <7> [42.585122] i915 device info: tuning_thread_rr_after_dep: no <7> [42.585125] i915 device info: unfenced_needs_alignment: no <7> [42.585129] i915 device info: hws_needs_physical: no <7> [42.585132] i915 device info: has_pooled_eu: no <7> [42.585135] i915 device info: rawclk rate: 19200 kHz <7> [42.585139] i915 device info: display version: 11 <7> [42.585143] i915 device info: cursor_needs_physical: no <7> [42.585146] i915 device info: has_cdclk_crawl: no <7> [42.585149] i915 device info: has_cdclk_squash: no <7> [42.585152] i915 device info: has_ddi: yes <7> [42.585155] i915 device info: has_dp_mst: yes <7> [42.585159] i915 device info: has_dsb: no <7> [42.585162] i915 device info: has_fpga_dbg: yes <7> [42.585165] i915 device info: has_gmch: no <7> [42.585168] i915 device info: has_hotplug: yes <7> [42.585171] i915 device info: has_hti: no <7> [42.585174] i915 device info: has_ipc: yes <7> [42.585177] i915 device info: has_overlay: no <7> [42.585181] i915 device info: has_psr: yes <7> [42.585184] i915 device info: has_psr_hw_tracking: yes <7> [42.585187] i915 device info: overlay_needs_physical: no <7> [42.585190] i915 device info: supports_tv: no <7> [42.585193] i915 device info: has_hdcp: no <7> [42.585196] i915 device info: has_dmc: yes <7> [42.585199] i915 device info: has_dsc: yes <7> [42.585203] i915 device info: iommu: enabled <7> [42.585207] i915 device info: available engines: 40403 <7> [42.585211] i915 device info: slice total: 1, mask=0001 <7> [42.585215] i915 device info: subslice total: 4 <7> [42.585218] i915 device info: slice0: 4 subslices, mask=0000000f <7> [42.585222] i915 device info: EU total: 16 <7> [42.585226] i915 device info: EU per subslice: 4 <7> [42.585229] i915 device info: has slice power gating: yes <7> [42.585232] i915 device info: has subslice power gating: yes <7> [42.585235] i915 device info: has EU power gating: yes <6> [42.585240] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [42.585244] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [42.585248] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [42.587237] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [42.587712] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [42.588275] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [42.588715] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [42.589365] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [42.589382] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [42.589392] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [42.589470] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [42.591141] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [42.594248] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [42.594711] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [42.596048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4 <7> [42.596738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [42.597163] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [42.598510] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to connected <7> [42.600027] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes : <7> [42.600046] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [42.600058] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa <7> [42.600069] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] <7> [42.600083] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [42.600779] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected <7> [42.600805] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected <7> [42.600819] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] <7> [42.600831] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [42.601960] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected <7> [42.601988] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected <7> [42.602009] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [42.602021] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [42.602521] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected <7> [42.602547] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [42.602565] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [42.602574] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [42.602580] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [42.602586] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [42.603086] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [42.603141] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [42.603148] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [42.603155] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [42.603161] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [42.603183] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <7> [42.603521] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7> [42.603646] i915 0000:00:02.0: [drm:intelfb_create [i915]] re-using BIOS fb <7> [42.604216] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x01740000 <6> [42.613894] fbcon: i915drmfb (fb0) is primary device <7> [42.616984] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [42.617501] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz <6> [42.619933] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [42.620633] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24 <7> [42.621067] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000 <7> [42.621454] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no <7> [42.622520] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long <7> [42.623117] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [42.623504] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A] <7> [42.624746] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,*twm, swm, stwm <7> [42.625214] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [42.625859] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 <7> [42.626505] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 <7> [42.627051] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [fastset] <7> [42.627526] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [42.627967] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [42.628367] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [42.629081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [42.629526] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [42.630004] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [42.630383] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64 <7> [42.630783] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [42.631157] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [42.631541] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [42.631959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [42.632342] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [42.633116] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [42.633562] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [42.634057] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [42.634424] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [42.634816] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310 <7> [42.635180] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0 <7> [42.635538] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [42.635925] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [42.636291] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [42.636700] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [42.637105] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [42.637473] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [42.638019] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [42.638413] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.638800] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.639371] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.639960] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [42.640332] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [42.640794] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.641247] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.641631] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [42.642171] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [42.642658] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:267] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [42.643039] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [42.643407] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0 <7> [42.643912] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [42.644352] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [42.644821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [42.645189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [42.645553] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [42.646047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [42.646421] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [42.666933] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [42.667441] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [42.668554] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0 <7> [42.669542] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <6> [42.671267] Console: switching to colour frame buffer device 400x112 <7> [42.671932] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=96000/96000 <7> [42.672405] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:239:eDP-1] set backlight level = 96000 <6> [42.692673] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device <7> [42.714027] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [42.714057] [drm:drm_client_modeset_probe] <7> [42.714469] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] <7> [42.714515] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [42.716190] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [42.716517] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [42.716853] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [42.717155] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [42.717778] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [42.717791] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [42.717798] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [42.717846] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [42.718152] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [42.719242] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [42.719533] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [42.720963] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes : <7> [42.720992] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [42.721002] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa <7> [42.721011] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] <7> [42.721022] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [42.721472] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected <7> [42.721483] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] <7> [42.721492] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [42.721855] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected <7> [42.721865] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [42.721873] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [42.722202] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [42.722210] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [42.722217] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [42.722221] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [42.722225] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [42.722436] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [42.722476] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [42.722482] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [42.722486] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [42.722491] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [42.722542] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <7> [42.731283] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [42.731295] [drm:drm_client_modeset_probe] <7> [42.731354] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] <7> [42.731366] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [42.732409] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [42.732751] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [42.733048] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [42.733343] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [42.733722] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [42.733735] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [42.733742] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [42.733775] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [42.734073] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [42.739177] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [42.739503] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [42.740631] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes : <7> [42.740643] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [42.740652] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa <7> [42.740661] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] <7> [42.740671] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [42.741010] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected <7> [42.741022] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] <7> [42.741030] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [42.741355] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected <7> [42.741364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [42.741372] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [42.741720] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [42.741728] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [42.741735] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [42.741739] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [42.741743] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [42.741806] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [42.741825] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [42.741830] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [42.741835] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [42.741839] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [42.741867] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <6> [42.840944] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 <6> [42.841288] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <7> [42.846420] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [42.847669] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <6> [42.847967] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [42.848415] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [42.848939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [42.849495] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x4810 <7> [42.852368] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [42.864533] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [42.897266] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [42.897403] [IGT] i915_module_load: exiting, ret=0

<4> [40.952088] **********************************************************

<4> [40.952092] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [40.952098] ** trace_printk() being used. Allocating extra memory. **

<4> [40.952104] ** This means that this is a DEBUG kernel and it is **

<4> [40.952112] ** If you see this message and you are not debugging **

<4> [40.952115] ** the kernel, report this immediately to your vendor! **

<4> [40.952121] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [40.952123] **********************************************************

<7> [41.043886] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K

<7> [41.044375] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)

<7> [41.044807] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH

<7> [41.045246] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [41.045929] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [41.046307] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz

<7> [41.047326] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001

<7> [41.047662] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001

<7> [41.048859] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [41.049190] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [41.049490] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M

<6> [41.049819] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [41.059448] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [41.059488] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7

<7> [41.060346] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K

<7> [41.061266] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018

<7> [41.061730] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0

<7> [41.062107] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [41.062474] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [41.062858] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [41.074303] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583

<7> [41.074859] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [41.075245] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [41.075634] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [41.076013] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [41.076328] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no

<7> [41.077119] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [41.077436] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no

<7> [41.077761] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no

<7> [41.078060] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [41.078357] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no

<7> [41.079579] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [41.080008] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [41.080306] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [41.080618] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50

<7> [41.081013] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68

<7> [41.081392] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56

<7> [41.081785] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834

<7> [41.082153] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941

<7> [41.082515] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878

<7> [41.082900] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899

<7> [41.083265] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488

<7> [41.083634] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583

<7> [41.084002] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069

<7> [41.084364] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719

<7> [41.084733] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483

<7> [41.085098] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280

<7> [41.085459] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000

<7> [41.085836] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000

<7> [41.086196] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000

<7> [41.086553] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000

<7> [41.086972] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000

<7> [41.087339] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000

<7> [41.087719] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000

<7> [41.088078] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000

<7> [41.089276] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [41.089930] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228

<7> [41.090314] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [41.090700] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)

<7> [41.091092] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [41.091465] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [41.091853] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)

<7> [41.092221] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)

<7> [41.092588] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [41.092979] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)

<7> [41.093345] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [41.093731] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)

<7> [41.094105] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)

<7> [41.094459] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [41.094829] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [41.095200] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806

<7> [41.095565] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6

<7> [41.096154] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [41.096529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [41.096903] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [41.097263] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [41.097635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000

<7> [41.098001] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [41.098355] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0

<7> [41.098721] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000

<7> [41.099085] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [41.099441] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0

<7> [41.099807] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000

<7> [41.100168] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a

<7> [41.100559] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [41.100972] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [41.101353] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [41.101791] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [41.102168] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [41.102521] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [41.102912] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [41.103355] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [41.103796] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 556800 kHz, VCO 1113600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 3

<7> [41.104168] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [41.104683] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.105050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [41.105411] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [41.105829] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [41.106205] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [41.106568] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [41.106956] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [41.107320] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [41.107706] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [41.108065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [41.108438] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<6> [41.108848] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem

<7> [41.108967] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4

<7> [41.109476] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin

<7> [41.112968] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [41.114018] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us

<7> [41.114439] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [41.114866] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [41.115245] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [41.115640] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<6> [41.116095] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)

<7> [41.116007] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [41.116361] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [41.116765] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [41.117122] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<7> [41.125712] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [41.131654] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 556800 kHz, VCO 1113600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 3

<7> [41.132457] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind

<6> [41.133200] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

<7> [41.133569] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz

<7> [41.133979] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz

<7> [41.134420] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT)

<7> [41.134853] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]

<7> [41.142633] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)

<7> [41.143084] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [41.143480] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [41.143896] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless

<7> [41.144305] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [41.144716] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300

<7> [41.145104] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002

<7> [41.145484] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName

<7> [41.147131] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [41.147555] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0

<7> [41.148236] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0

<7> [41.148710] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000

<7> [41.149075] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [41.149432] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [41.150153] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [41.150519] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [41.151010] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [41.151639] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [41.152265] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [41.152752] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f

<7> [41.154388] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [41.155138] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001

<7> [41.155711] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6

<7> [41.156797] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1

<7> [41.161991] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.163649] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.165517] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.167407] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.169269] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.170811] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.172645] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.174545] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [41.175925] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [41.175955] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [41.175963] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [41.176096] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [41.176513] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa

<7> [41.176920] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)

<7> [41.190330] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none

<7> [41.190907] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)

<7> [41.191291] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, enabled, brightness 96000/96000

<7> [41.191789] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000

<7> [41.192142] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [41.192494] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [41.192855] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [41.193201] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [41.193669] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [41.194532] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT)

<7> [41.194947] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]

<7> [41.195743] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [41.196115] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]

<7> [41.196458] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)

<7> [41.197088] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]

<7> [41.197431] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)

<7> [41.198671] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: enabled

<7> [41.199189] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled

<7> [41.199683] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled

<7> [41.200053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: enabled, pipe A

<7> [41.200420] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A

<7> [41.200809] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A

<7> [41.201174] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A

<7> [41.201536] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A

<7> [41.201922] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A

<7> [41.202288] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A

<7> [41.202673] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A

<7> [41.203042] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B

<7> [41.203395] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B

<7> [41.203777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B

<7> [41.204150] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B

<7> [41.204526] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B

<7> [41.204913] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B

<7> [41.205278] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B

<7> [41.205665] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B

<7> [41.206037] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C

<7> [41.206394] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C

<7> [41.206767] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C

<7> [41.207148] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C

<7> [41.207523] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C

<7> [41.207911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C

<7> [41.208271] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C

<7> [41.208650] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C

<7> [41.209069] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0

<7> [41.209556] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: enabled, pipe A

<7> [41.209954] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [41.210316] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A

<7> [41.210685] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B

<7> [41.211032] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C

<7> [41.211392] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A

<7> [41.211785] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0

<7> [41.212143] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1

<7> [41.212509] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [41.212903] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0

<7> [41.213473] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: enabled

<7> [41.213911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled

<7> [41.214289] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled

<7> [41.214685] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled

<7> [41.215295] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 181030 kHz

<7> [41.215686] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz

<7> [41.216038] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz

<7> [41.216377] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz

<7> [41.216735] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz

<7> [41.217087] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz

<7> [41.217430] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz

<7> [41.217791] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz

<7> [41.218143] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 1448240 num active planes 1

<7> [41.218510] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz

<7> [41.218876] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz

<7> [41.219222] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz

<7> [41.219567] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz

<7> [41.219930] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz

<7> [41.220272] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz

<7> [41.220630] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz

<7> [41.220979] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz

<7> [41.221319] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [41.221696] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz

<7> [41.222048] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz

<7> [41.222391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz

<7> [41.222752] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz

<7> [41.223097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz

<7> [41.223442] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz

<7> [41.223802] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz

<7> [41.224146] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz

<7> [41.224491] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [41.224903] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [41.247803] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [setup_hw_state]

<7> [41.248285] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [41.248781] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 18, dithering: 0

<7> [41.249226] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [41.249578] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [41.249952] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [41.250307] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [41.250678] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 3157174, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64

<7> [41.251040] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [41.251385] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [41.251748] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [41.252107] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [41.252452] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [41.252814] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [41.253172] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=362060, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [41.253520] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [41.253885] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=362060, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [41.254242] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 541120, pipe src: 3200x1800+0+0, pixel rate 362060

<7> [41.254591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0

<7> [41.254959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [41.255312] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [41.255683] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [41.256042] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [41.256404] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [41.256768] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [41.257126] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [41.257475] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.257875] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.258229] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.258580] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [41.258950] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [41.259303] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.259671] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.260029] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.260371] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [41.260736] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]

<7> [41.261093] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]

<7> [41.261656] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x1, ddb (0 - 682), active pipes 0x1, mbus joined: no

<7> [41.262020] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [41.262375] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [41.263346] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] pipe A/plane 1A with fb: size=3200x1800@32, offset=0, pitch 12800, size 0x15f9000

<7> [41.263767] i915 0000:00:02.0: [drm:_i915_gem_object_stolen_init [i915]] creating preallocated stolen object: stolen_offset=0x0000000000000000, size=0x00000000015f9000

<7> [41.266821] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[15f9000, 15fb000] for use by error capture

<7> [41.267166] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [15fb000, 100000000]

<7> [41.267498] MCR Steering: Default steering: group=0x0, instance=0x0

<7> [41.267522] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global

<7> [41.268996] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0

<7> [41.269392] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0

<7> [41.269790] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0

<7> [41.272279] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0

<7> [41.273591] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0

<7> [41.274834] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0

<7> [41.290149] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate

<7> [41.290588] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [41.291428] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate

<7> [41.291854] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [41.292284] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate

<7> [41.292678] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [41.293180] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [41.293589] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz

<7> [41.293973] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24

<7> [41.294330] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000

<7> [41.294704] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no

<7> [41.295059] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long

<7> [41.295414] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [41.295806] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]

<7> [41.296165] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 3157174/8388608 link 350797/524288, found tu 64, data 4209566/8388608 link 350797/524288)

<7> [41.296539] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x01c001a5, found 0x00e001a5)

<7> [41.296931] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 18, found 24)

<7> [41.297305] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 362060, found 361310)

<7> [41.297695] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 362060, found 361310)

<7> [41.298070] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 541120, found 540000)

<7> [41.298441] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [41.298825] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0

<7> [41.299246] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no

<7> [41.299631] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 682) -> (0 - 1024), active pipes 0x1 -> 0x1

<7> [41.300234] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset due to unsupported link rate

<7> [41.300593] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:238:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [41.301061] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [41.301457] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz

<7> [41.301833] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24

<7> [41.302186] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000

<7> [41.302537] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no

<7> [41.302940] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long

<7> [41.303340] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [41.303759] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]

<7> [41.304114] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 3157174/8388608 link 350797/524288, found tu 64, data 4209566/8388608 link 350797/524288)

<7> [41.304486] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x01c001a5, found 0x00e001a5)

<7> [41.304871] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 18, found 24)

<7> [41.305238] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 362060, found 361310)

<7> [41.305617] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 362060, found 361310)

<7> [41.305988] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 541120, found 540000)

<7> [41.306352] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [41.306725] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0

<7> [41.307128] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0x3 -> 0x1 (total dbuf slices 0x3), mbus joined? no->no

<7> [41.307489] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x1, ddb (0 - 682) -> (0 - 1024), active pipes 0x1 -> 0x1

<7> [41.307967] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 682) -> ( 0 - 985), size 682 -> 985

<7> [41.308328] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39

<7> [41.308699] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm

<7> [41.309058] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [41.309408] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 27, 27, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 0, 0, 0

<7> [41.309774] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 0, 0, 0

<7> [41.310133] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.310479] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.310918] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.311274] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.311651] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.312003] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.312347] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.312719] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.313079] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.313426] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.313791] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.314146] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.314491] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.314853] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.315207] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.315561] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.315928] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.316273] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.316644] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.316998] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:plane 6A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.317338] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.317700] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.318054] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.318396] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:85:plane 7A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.318755] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [41.319110] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] lines 1, 1, 1, 1, 1, 1, 1, 1, 1, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.319460] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] blocks 7, 7, 7, 7, 7, 7, 7, 7, 7, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.319830] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [41.320186] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1

<7> [41.320549] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [41.320928] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446

<7> [41.321300] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446

<7> [41.321752] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)

<7> [41.322121] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [41.322480] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz

<7> [41.322864] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1

<7> [41.323232] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0

<7> [41.323586] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0

<7> [41.323977] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]

<7> [41.324346] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [41.324718] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [41.325081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [41.325433] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [41.325803] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [41.326163] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [41.326522] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64

<7> [41.326909] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [41.327271] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [41.327643] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [41.328005] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [41.328359] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 362060 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [41.328749] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [41.329113] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [41.329471] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [41.329843] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [41.330203] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310

<7> [41.330559] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0

<7> [41.330935] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [41.331293] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [41.331665] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [41.332025] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [41.332378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [41.332746] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [41.333109] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [41.333459] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.333823] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.334183] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.334540] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [41.334914] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [41.335268] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.335636] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.335996] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [41.336344] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [41.336708] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:267] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [41.337072] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [41.337422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0

<7> [41.337799] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [41.338159] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [41.338512] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [41.338882] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [41.339240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [41.339594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [41.339968] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [41.346681] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [41.550097] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0

<7> [41.553022] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [41.572867] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off

<7> [41.573880] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [41.574827] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [41.626691] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [41.627751] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [41.629793] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A]

<7> [41.631228] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [41.632266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [41.633367] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1

<7> [41.635152] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [41.636188] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [41.637171] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [41.638102] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [41.639026] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [41.639959] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [41.640912] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [41.641878] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [41.642863] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [41.643805] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x3

<7> [41.644840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [41.645840] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]

<7> [41.646771] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [41.649528] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on

<7> [41.650520] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [42.246144] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [42.247169] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [42.248102] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on

<7> [42.249036] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063

<7> [42.459717] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [42.460816] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [42.462344] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [42.463516] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [42.466975] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [42.467092] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14

<7> [42.468505] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [42.469048] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [42.470555] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0

<7> [42.471021] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0

<7> [42.472760] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK

<7> [42.473160] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [42.475228] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1

<7> [42.475705] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1

<7> [42.477943] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [42.478315] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4

<7> [42.479060] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [42.479838] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [42.480202] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [42.480587] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000

<7> [42.484494] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [42.484931] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]

<7> [42.497232] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [42.498014] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [42.498404] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [42.499407] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0

<7> [42.499877] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp

<7> [42.500362] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [42.501361] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] found possible fb from [PLANE:31:plane 1A]

<7> [42.501846] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping

<7> [42.502194] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping

<7> [42.502542] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] checking [PLANE:31:plane 1A] for BIOS fb

<7> [42.502916] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] area: 3200x1800, bpp: 32, size: 23040000

<7> [42.503271] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] fb big enough [PLANE:31:plane 1A] (23040000 >= 23040000)

<7> [42.503628] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping

<7> [42.503982] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping

<7> [42.504329] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] using BIOS fb for initial console

<7> [42.506223] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [42.506560] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [42.506885] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [42.507200] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [42.519272] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered

<7> [42.519946] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1

<7> [42.522420] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event

<7> [42.523370] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1

<7> [42.525661] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event

<7> [42.526427] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event

<7> [42.527180] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event

<6> [42.527281] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [42.531777] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected

<6> [42.566292] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [42.574957] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input4

<7> [42.579284] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x4810 (init value 0x4810)

<6> [42.579924] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [42.582931] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]

<7> [42.582977] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [42.584473] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [42.584954] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11

<7> [42.585218] i915 device info: slice0: 4 subslices, mask=0000000f

<6> [42.585244] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [42.585248] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [42.587237] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [42.587712] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [42.588275] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [42.588715] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [42.589365] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [42.589382] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [42.589392] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [42.589470] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [42.591141] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [42.594248] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [42.594711] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [42.596048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4

<7> [42.596738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3

<7> [42.597163] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [42.598510] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to connected

<7> [42.600027] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :

<7> [42.600046] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [42.600058] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa

<7> [42.600069] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]

<7> [42.600083] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [42.600779] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected

<7> [42.600805] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected

<7> [42.600819] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]

<7> [42.600831] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [42.601960] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected

<7> [42.601988] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [42.602009] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [42.602021] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [42.602521] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected

<7> [42.602547] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [42.602565] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [42.602574] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [42.602580] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [42.602586] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [42.603086] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [42.603141] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [42.603148] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [42.603155] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [42.603161] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [42.603183] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<7> [42.603521] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<7> [42.603646] i915 0000:00:02.0: [drm:intelfb_create [i915]] re-using BIOS fb

<7> [42.604216] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x01740000

<7> [42.616984] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [42.617501] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz

<6> [42.619933] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [42.620633] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24

<7> [42.621067] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000

<7> [42.621454] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no

<7> [42.622520] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long

<7> [42.623117] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [42.623504] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]

<7> [42.624746] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm

<7> [42.625214] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [42.625859] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0

<7> [42.626505] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0

<7> [42.627051] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [fastset]

<7> [42.627526] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [42.627967] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [42.628367] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [42.629081] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [42.629526] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [42.630004] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [42.630383] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64

<7> [42.630783] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [42.631157] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [42.631541] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [42.631959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [42.632342] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [42.633116] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [42.633562] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [42.634057] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [42.634424] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [42.634816] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310

<7> [42.635180] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0

<7> [42.635538] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [42.635925] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [42.636291] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [42.636700] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [42.637105] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [42.637473] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [42.638019] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [42.638413] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.638800] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.639371] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.639960] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [42.640332] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [42.640794] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.641247] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.641631] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [42.642171] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [42.642658] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:267] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [42.643039] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [42.643407] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0

<7> [42.643912] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [42.644352] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [42.644821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [42.645189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [42.645553] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [42.646047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [42.646421] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [42.666933] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [42.667441] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [42.668554] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0

<7> [42.669542] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<6> [42.671267] Console: switching to colour frame buffer device 400x112

<7> [42.671932] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=96000/96000

<7> [42.672405] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:239:eDP-1] set backlight level = 96000

<6> [42.692673] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device

<7> [42.714027] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]

<7> [42.714469] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]

<7> [42.714515] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [42.716190] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [42.716517] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [42.716853] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [42.717155] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [42.717778] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [42.717791] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [42.717798] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [42.717846] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [42.718152] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [42.719242] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [42.719533] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [42.720963] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :

<7> [42.720992] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [42.721002] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa

<7> [42.721011] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]

<7> [42.721022] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [42.721472] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected

<7> [42.721483] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]

<7> [42.721492] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [42.721855] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [42.721865] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [42.721873] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [42.722202] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [42.722210] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [42.722217] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [42.722221] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [42.722225] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [42.722436] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [42.722476] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [42.722482] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [42.722486] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [42.722491] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [42.722542] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<7> [42.731283] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]

<7> [42.731354] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]

<7> [42.731366] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [42.732409] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [42.732751] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [42.733048] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [42.733343] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [42.733722] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [42.733735] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [42.733742] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [42.733775] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [42.734073] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [42.739177] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [42.739503] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [42.740631] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :

<7> [42.740643] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [42.740652] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa

<7> [42.740661] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]

<7> [42.740671] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [42.741010] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected

<7> [42.741022] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]

<7> [42.741030] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [42.741355] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [42.741364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [42.741372] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [42.741720] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [42.741728] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [42.741735] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [42.741739] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [42.741743] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [42.741806] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [42.741825] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [42.741830] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [42.741835] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [42.741839] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [42.741867] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<6> [42.840944] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100

<6> [42.841288] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)

<6> [42.847669] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<6> [42.847967] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [42.848415] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [42.848939] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [42.849495] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x4810

<7> [42.852368] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<6> [42.897266] [IGT] i915_module_load: finished subtest load, SUCCESS

Results for igt@i915_module_load@load