Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.28-gd991240f6 (x86_64) (Linux: 6.6.0-rc3-linus-v6.6-rc3-g6465e260f487+ x86_64) |
| Out |
Starting subtest: basic-s2idle-without-i915 Opened device: /dev/dri/card0 [cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Sun Sep 24 21:52:08 2023 Subtest basic-s2idle-without-i915: SUCCESS (4.148s) |
| Err |
Starting subtest: basic-s2idle-without-i915 Subtest basic-s2idle-without-i915: SUCCESS (4.148s) |
| Dmesg |
<6> [471.735830] [IGT] i915_suspend: executing
<6> [471.739950] [IGT] i915_suspend: starting subtest basic-s2idle-without-i915
<7> [471.947002] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [471.947320] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [471.947548] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [471.947835] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [471.948257] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [471.948501] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [471.949527] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [471.949779] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [471.950006] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [471.950251] i915 0000:00:02.0: vgaarb: deactivate vga console
<7> [471.950590] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [471.950901] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [471.951560] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018
<7> [471.951919] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [471.952219] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [471.952507] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [471.952814] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [471.960728] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [471.960967] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [471.961173] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [471.961377] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [471.961585] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: LPDDR3
<7> [471.961774] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [471.962002] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [471.962154] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [471.962305] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [471.962453] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [471.962600] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [471.962780] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [471.962988] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [471.963137] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [471.963739] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [471.964024] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203
<7> [471.964347] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [471.964696] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [471.965026] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [471.965351] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [471.965688] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [471.966015] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [471.966335] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [471.966656] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [471.967000] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [471.967323] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [471.967638] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [471.967949] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [471.968261] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [471.968579] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [471.968918] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [471.969240] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [471.969550] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [471.969895] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [471.970211] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [471.970523] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [471.970849] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [471.971158] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [471.971475] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [471.971826] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [471.972247] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [471.972607] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [471.972954] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [471.973273] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [471.973588] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Max dotclock rate: 675000 kHz
<7> [471.973932] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [471.974361] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [471.974693] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [471.975011] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [471.975322] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [471.975758] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [471.976080] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [471.976398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [471.976744] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [471.977107] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin
<7> [471.978160] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [471.979843] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<6> [471.980181] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)
<7> [471.980146] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [471.980362] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [471.980572] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [471.980925] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [471.981139] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [471.981346] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [471.981552] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [471.981795] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [471.982061] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [471.985431] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [471.987968] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [471.988347] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT)
<7> [471.988691] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [471.994708] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [471.995047] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [471.995362] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [471.995706] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [471.996031] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [471.996348] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [471.996665] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP
<7> [471.996997] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [471.997311] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0
<7> [471.997627] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0
<7> [471.998086] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [471.998453] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [471.998779] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [471.999069] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [471.999365] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [471.999659] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [472.000056] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [472.000740] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [472.001059] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [472.001429] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [472.001767] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [472.002104] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [472.002410] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [472.210893] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [472.212117] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [472.213551] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40
<7> [472.216749] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [472.234836] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.234885] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.234916] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.235260] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.236405] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.237857] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:95:eDP-1] DRRS type: static
<7> [472.239851] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:95:eDP-1] Using native PCH PWM for backlight control
<7> [472.240910] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:95:eDP-1] backlight initialized, disabled, brightness 0/937
<7> [472.242138] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [472.243030] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [472.243909] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [472.244779] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [472.245449] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [472.246135] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [472.247796] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DDI B/PHY B] Using AUX CH B (VBT)
<7> [472.248468] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DDI B/PHY B]
<7> [472.250247] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [472.250784] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:102:DDI B/PHY B]
<7> [472.251242] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:102:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [472.252265] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:117:DDI C/PHY C] Using AUX CH C (VBT)
<7> [472.252800] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:117:DDI C/PHY C]
<7> [472.253928] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [472.254433] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:117:DDI C/PHY C]
<7> [472.254938] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:117:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [472.256218] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [472.256749] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [472.257234] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [472.257653] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [472.258100] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [472.258521] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [472.258956] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [472.259377] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [472.259816] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [472.260230] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [472.260579] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [472.260960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [472.261317] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [472.261662] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [472.262016] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DP-MST A] hw state readout: disabled, pipe A
<7> [472.262352] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:105:DP-MST B] hw state readout: disabled, pipe B
<7> [472.262708] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP-MST C] hw state readout: disabled, pipe C
<7> [472.263056] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [472.263391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
<7> [472.263738] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
<7> [472.264071] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
<7> [472.264429] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [472.264811] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [472.265169] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [472.265535] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [472.266051] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:eDP-1] hw state readout: disabled
<7> [472.266402] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [472.266770] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:112:HDMI-A-1] hw state readout: disabled
<7> [472.267110] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
<7> [472.267460] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:124:HDMI-A-2] hw state readout: disabled
<7> [472.267796] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [472.268124] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [472.268430] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [472.268744] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [472.269071] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [472.269359] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [472.269650] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [472.269958] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [472.270257] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [472.270548] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [472.270863] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [472.271160] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [472.271594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [472.271923] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [472.272223] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [472.272528] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [472.272843] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [472.273130] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [472.273419] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [472.273821] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [472.274071] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [472.274361] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [472.274666] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 GT workarounds on global
<7> [472.277000] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [472.277347] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [472.277657] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 context workarounds on rcs'0
<7> [472.302163] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [472.302752] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [472.303050] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [472.303339] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [472.303621] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [472.303972] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [472.304985] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [472.305238] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [472.305478] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [472.305864] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [472.312958] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:95:eDP-1] backlight device intel_backlight registered
<7> [472.313464] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [472.316463] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:eDP-1] generating connector hotplug event
<7> [472.317703] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [472.319111] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<7> [472.319846] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:112:HDMI-A-1] generating connector hotplug event
<7> [472.320464] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [472.321599] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:118:DP-2] generating connector hotplug event
<7> [472.322605] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:124:HDMI-A-2] generating connector hotplug event
<6> [472.322767] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [472.327265] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected
<6> [472.356331] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [472.364457] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input72
<7> [472.366895] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [472.368148] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [472.368509] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [472.368809] [drm:drm_client_modeset_probe]
<7> [472.368898] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [472.368914] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [472.368945] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [472.369285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [472.370305] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [472.370632] i915 device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9
<7> [472.370640] i915 device info: graphics version: 9
<7> [472.370645] i915 device info: media version: 9
<7> [472.370649] i915 device info: graphics stepping: H0
<7> [472.370654] i915 device info: media stepping: H0
<7> [472.370658] i915 device info: display stepping: H0
<7> [472.370662] i915 device info: base die stepping: **
<7> [472.370667] i915 device info: gt: 2
<7> [472.370686] i915 device info: memory-regions: 0x21
<7> [472.370690] i915 device info: page-sizes: 0x11000
<7> [472.370694] i915 device info: platform: SKYLAKE
<7> [472.370699] i915 device info: ppgtt-size: 48
<7> [472.370703] i915 device info: ppgtt-type: 2
<7> [472.370707] i915 device info: dma_mask_size: 39
<7> [472.370711] i915 device info: is_mobile: no
<7> [472.370715] i915 device info: is_lp: no
<7> [472.370720] i915 device info: require_force_probe: no
<7> [472.370724] i915 device info: is_dgfx: no
<7> [472.370728] i915 device info: has_64bit_reloc: yes
<7> [472.370733] i915 device info: has_64k_pages: no
<7> [472.370737] i915 device info: gpu_reset_clobbers_display: no
<7> [472.370741] i915 device info: has_reset_engine: yes
<7> [472.370745] i915 device info: has_3d_pipeline: yes
<7> [472.370750] i915 device info: has_4tile: no
<7> [472.370754] i915 device info: has_flat_ccs: no
<7> [472.370759] i915 device info: has_global_mocs: no
<7> [472.370763] i915 device info: has_gmd_id: no
<7> [472.370767] i915 device info: has_gt_uc: yes
<7> [472.370772] i915 device info: has_heci_pxp: no
<7> [472.370776] i915 device info: has_heci_gscfi: no
<7> [472.370780] i915 device info: has_guc_deprivilege: no
<7> [472.370785] i915 device info: has_l3_ccs_read: no
<7> [472.370789] i915 device info: has_l3_dpf: no
<7> [472.370794] i915 device info: has_llc: yes
<7> [472.370798] i915 device info: has_logical_ring_contexts: yes
<7> [472.370802] i915 device info: has_logical_ring_elsq: no
<7> [472.370806] i915 device info: has_media_ratio_mode: no
<7> [472.370810] i915 device info: has_mslice_steering: no
<7> [472.370813] i915 device info: has_oa_bpc_reporting: no
<7> [472.370817] i915 device info: has_oa_slice_contrib_limits: no
<7> [472.370821] i915 device info: has_oam: no
<7> [472.370825] i915 device info: has_one_eu_per_fuse_bit: no
<7> [472.370829] i915 device info: has_pxp: no
<7> [472.370832] i915 device info: has_rc6: yes
<7> [472.370836] i915 device info: has_rc6p: no
<7> [472.370840] i915 device info: has_rps: yes
<7> [472.370844] i915 device info: has_runtime_pm: yes
<7> [472.370847] i915 device info: has_snoop: no
<7> [472.370851] i915 device info: has_coherent_ggtt: yes
<7> [472.370855] i915 device info: tuning_thread_rr_after_dep: no
<7> [472.370859] i915 device info: unfenced_needs_alignment: no
<7> [472.370863] i915 device info: hws_needs_physical: no
<7> [472.370867] i915 device info: has_pooled_eu: no
<7> [472.370870] i915 device info: rawclk rate: 24000 kHz
<7> [472.370875] i915 device info: display version: 9
<7> [472.370879] i915 device info: cursor_needs_physical: no
<7> [472.370883] i915 device info: has_cdclk_crawl: no
<7> [472.370887] i915 device info: has_cdclk_squash: no
<7> [472.370890] i915 device info: has_ddi: yes
<7> [472.370894] i915 device info: has_dp_mst: yes
<7> [472.370898] i915 device info: has_dsb: no
<7> [472.370902] i915 device info: has_fpga_dbg: yes
<7> [472.370905] i915 device info: has_gmch: no
<7> [472.370909] i915 device info: has_hotplug: yes
<7> [472.370913] i915 device info: has_hti: no
<7> [472.370917] i915 device info: has_ipc: yes
<7> [472.370920] i915 device info: has_overlay: no
<7> [472.370924] i915 device info: has_psr: yes
<7> [472.370928] i915 device info: has_psr_hw_tracking: yes
<7> [472.370932] i915 device info: overlay_needs_physical: no
<7> [472.370935] i915 device info: supports_tv: no
<7> [472.370939] i915 device info: has_hdcp: yes
<7> [472.370943] i915 device info: has_dmc: yes
<7> [472.370947] i915 device info: has_dsc: no
<7> [472.370797] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [472.370951] i915 device info: iommu: disabled
<7> [472.370955] i915 device info: available engines: 40403
<7> [472.370958] i915 device info: slice total: 1, mask=0001
<7> [472.370962] i915 device info: subslice total: 3
<7> [472.370966] i915 device info: slice0: 3 subslices, mask=00000007
<7> [472.370970] i915 device info: slice1: 0 subslices, mask=00000000
<7> [472.370973] i915 device info: slice2: 0 subslices, mask=00000000
<7> [472.370977] i915 device info: EU total: 24
<7> [472.370980] i915 device info: EU per subslice: 8
<7> [472.370983] i915 device info: has slice power gating: no
<7> [472.370986] i915 device info: has subslice power gating: no
<7> [472.370989] i915 device info: has EU power gating: yes
<6> [472.370993] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [472.370997] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [472.371000] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [472.371112] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [472.371400] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [472.371702] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [472.372012] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.372026] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.372037] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.372074] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [472.372364] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [472.376275] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [472.376607] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [472.377657] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [472.378988] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] status updated from unknown to connected
<7> [472.379197] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [472.379208] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.379220] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.379233] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [472.379247] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [472.379952] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] status updated from unknown to disconnected
<7> [472.379977] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [472.380000] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [472.380013] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [472.381326] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.381654] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [472.384790] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.385144] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.385157] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.385453] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [472.389026] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.389041] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [472.389364] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] status updated from unknown to disconnected
<7> [472.389394] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [472.389420] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [472.389433] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [472.389806] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] status updated from unknown to disconnected
<7> [472.389832] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [472.389843] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [472.389855] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [472.391520] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.391858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [472.394759] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.395100] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.395113] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.395403] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [472.399349] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.399363] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [472.401449] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] status updated from unknown to disconnected
<7> [472.401481] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [472.401493] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [472.401502] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [472.401510] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [472.401517] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [472.401524] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [472.401592] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [472.401612] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [472.401620] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [472.401627] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [472.401634] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [472.401657] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [472.401724] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [472.401832] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [472.407321] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x000c0000
<6> [472.408140] fbcon: i915drmfb (fb0) is primary device
<6> [472.408711] Console: switching to colour frame buffer device 400x112
<6> [472.408732] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [472.418823] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [472.418837] [drm:drm_client_modeset_probe]
<7> [472.418917] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [472.418932] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [472.424063] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [472.424346] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [472.424593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [472.424869] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [472.425150] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.425164] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.425175] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.425210] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [472.425461] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [472.426586] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [472.426858] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [472.427951] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [472.427964] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.427976] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.427989] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [472.428002] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [472.428760] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [472.428775] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [472.428787] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [472.429761] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.430027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [472.430495] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.430799] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.430812] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.431051] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<6> [472.435284] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [472.435548] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.435561] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [472.435862] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [472.435878] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [472.435891] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [472.436195] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [472.436208] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [472.436220] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [472.439757] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.440026] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [472.440562] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.440858] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.440871] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.441112] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [472.444525] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.444539] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [472.445503] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [472.445515] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [472.445523] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [472.445529] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [472.445534] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [472.445539] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [472.445594] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [472.445608] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [472.445614] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [472.445620] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [472.445626] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [472.445649] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [472.445984] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:95:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [472.446250] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 373250KHz
<7> [472.446449] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [472.446642] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1119750 available 2160000
<7> [472.446907] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:95:eDP-1] SDP split enable: no
<7> [472.447155] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:51:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [472.447425] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:94:DDI A/PHY A] [CRTC:51:pipe A]
<7> [472.447708] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [472.447976] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [472.448242] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [472.448511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [472.448809] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
<7> [472.449079] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [472.449345] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [472.449611] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [472.449902] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
<7> [472.450167] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [472.450431] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
<7> [472.453697] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [472.454006] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [472.454278] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [472.454546] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
<7> [472.454861] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [472.455129] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
<7> [472.455396] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [472.455663] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
<7> [472.456063] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [472.456333] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
<7> [472.456600] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [472.456891] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
<7> [472.457161] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [472.457428] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [472.457721] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [472.457989] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
<7> [472.458257] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [472.458521] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
<7> [472.458848] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [472.459120] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
<7> [472.459389] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [472.459659] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [472.460338] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [472.460620] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000001)
<7> [472.460917] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [472.461188] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
<7> [472.461455] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
<7> [472.463652] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [472.463972] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [472.464301] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
<7> [472.464600] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 856), size 0 -> 856
<7> [472.464882] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36
<7> [472.465140] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
<7> [472.465393] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [472.465653] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0
<7> [472.466034] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0
<7> [472.466331] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (373250 kHz) > [CRTC:51:pipe A] min cdclk (0 kHz)
<7> [472.466605] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
<7> [472.466905] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [472.467167] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
<7> [472.467430] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [472.467723] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:51:pipe A] allocated DPLL 0
<7> [472.467987] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:51:pipe A] reserving DPLL 0
<7> [472.468255] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: yes [modeset]
<7> [472.468523] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [472.468824] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [472.469086] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [472.469347] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [472.469611] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [472.469903] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [472.470166] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
<7> [472.470431] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [472.470720] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [472.470989] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [472.471253] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0
<7> [472.471261] i915 0000:00:02.0: pixelformat: RGB
<7> [472.471268] i915 0000:00:02.0: colorimetry: sRGB
<7> [472.471274] i915 0000:00:02.0: bpc: 0
<7> [472.471281] i915 0000:00:02.0: dynamic range: VESA range
<7> [472.471287] i915 0000:00:02.0: content type: Not defined
<7> [472.471861] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [472.472148] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.472420] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.472728] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [472.472994] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.473266] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [472.473534] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
<7> [472.473930] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
<7> [472.474195] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [472.474466] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [472.475697] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [472.475984] i915 0000:00:02.0: [drm:skl_dump_hw_state [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
<7> [472.476246] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [472.476511] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [472.476804] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [472.477070] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [472.477334] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [472.477595] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [472.477886] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [472.478156] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:96] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [472.478425] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [472.479546] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [472.479848] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [472.480114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [472.480796] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
<7> [472.481942] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [472.482220] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [472.482477] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [472.482778] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [472.483033] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [472.483294] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [472.483554] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [472.483878] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [472.484138] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [472.484398] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [472.484856] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [472.485144] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [472.485427] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [472.487866] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:51:pipe A]
<7> [472.488175] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [472.489000] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power on
<7> [472.489349] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [472.489667] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [472.490087] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [472.490360] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power on
<7> [472.490660] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000000b
<7> [472.498801] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [472.691958] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [472.692759] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [472.694156] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [472.698977] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [472.699888] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [472.702035] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [472.702968] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [472.703908] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [472.707084] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Clock recovery OK
<7> [472.708526] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
<7> [472.709813] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS2
<7> [472.714217] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [472.715349] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [472.716526] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [472.721862] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [472.722969] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [472.724158] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [472.729019] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [472.730563] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [472.733255] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [472.736138] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [472.737542] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [472.739927] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 937
<7> [472.742473] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, limit: 1
<7> [472.744176] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [472.749442] i915 0000:00:02.0: [drm:intel_pipe_update_end [i915]] Atomic update on pipe (A) took 432 us, max time under evasion is 250 us
<7> [472.752872] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
<7> [472.761858] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [472.763873] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [472.766327] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [472.767969] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<6> [472.775326] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [472.777254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [472.787629] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [472.793600] i915 0000:00:02.0: [drm:intel_pipe_update_end [i915]] Atomic update on pipe (A) took 536 us, max time under evasion is 250 us
<7> [472.805827] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [472.805861] [drm:drm_client_modeset_probe]
<7> [472.806156] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [472.806201] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [472.810188] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [472.811100] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [472.811935] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [472.812610] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [472.813474] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [472.813514] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [472.813545] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [472.813735] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [472.814365] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [472.815730] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [472.816315] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [472.819048] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [472.819073] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [472.819098] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [472.819120] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [472.819143] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [472.820003] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [472.820029] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [472.820053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [472.821984] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.822503] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [472.823637] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [472.824096] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.824115] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.824519] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [472.828592] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [472.828613] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [472.829042] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [472.829063] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [472.829083] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [472.829495] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [472.829509] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [472.829527] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [472.830229] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.830599] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [472.831238] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [472.831632] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.831649] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [472.832097] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [472.835938] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [472.835954] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [472.836291] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [472.836304] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [472.836313] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [472.836320] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [472.836326] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [472.836332] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [472.836395] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [472.836413] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [472.836421] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [472.836427] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [472.836434] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [472.836466] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<6> [472.852925] [IGT] Unloading i915
<6> [472.854321] Console: switching to colour dummy device 80x25
<6> [472.869061] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
<6> [472.869087] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [472.869095] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [472.869102] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [472.869108] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [472.869113] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19
<6> [472.869120] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a
<6> [472.869125] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
<7> [472.936310] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [472.936568] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [472.936773] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [472.937054] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [472.937237] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [472.937416] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [472.937595] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [472.937807] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [472.938032] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [472.947952] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input73
<6> [472.964793] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input74
<6> [472.974616] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input75
<6> [472.979023] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input76
<7> [473.085729] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [473.168172] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [473.168712] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [473.169062] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [473.169406] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [473.171142] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)
<7> [473.171455] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 1, found 0)
<7> [473.171836] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)
<7> [473.172195] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [473.172538] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4348677/8388608 link 362389/524288, found tu 0, data 0/0 link 0/0)
<7> [473.173159] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [473.173489] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [473.173862] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)
<7> [473.174256] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3360, found 0)
<7> [473.174646] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)
<7> [473.175156] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3360, found 0)
<7> [473.175549] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)
<7> [473.175981] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)
<7> [473.176378] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [473.176813] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1852, found 0)
<7> [473.177210] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [473.177606] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1852, found 0)
<7> [473.178038] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [473.178430] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1808, found 0)
<7> [473.178853] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)
<7> [473.179255] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3360, found 0)
<7> [473.179611] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)
<7> [473.180022] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3360, found 0)
<7> [473.180357] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)
<7> [473.180729] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)
<7> [473.181057] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [473.181366] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1852, found 0)
<7> [473.181642] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [473.182057] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1852, found 0)
<7> [473.182377] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [473.182652] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1808, found 0)
<7> [473.182965] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [473.183267] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [473.183542] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [473.183862] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [473.184161] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 373250, found 0)
<7> [473.184492] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 373250, found 0)
<7> [473.184831] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [473.185133] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [473.185410] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:51:pipe A] releasing DPLL 0
<7> [473.185825] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 892) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [473.186304] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 856) -> ( 0 - 0), size 856 -> 0
<7> [473.186714] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 856 - 892) -> ( 0 - 0), size 36 -> 0
<7> [473.187089] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [473.187462] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [473.187845] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [473.188182] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [473.188511] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [473.188854] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 337500 kHz, actual 337500 kHz
<7> [473.189156] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
<7> [473.189436] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [modeset]
<7> [473.189761] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
<7> [473.190056] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [473.190331] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [473.190882] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1
<7> [473.193103] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [473.400242] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 0
<7> [473.402629] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [473.424030] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x01000000, dig 0x11001010, pins 0x00000010, long 0x00000000
<7> [473.424300] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power off
<7> [473.425648] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:94:DDI A/PHY A] - short
<7> [473.425985] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [473.427796] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000000
<7> [473.477047] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [473.478243] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x01000000, dig 0x12001010, pins 0x00000010, long 0x00000010
<7> [473.479598] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:94:DDI A/PHY A] - long
<7> [473.479861] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:94:DDI A/PHY A]
<7> [473.479848] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:51:pipe A]
<7> [473.481150] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [473.482111] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
<7> [473.482866] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:94:DDI A/PHY A]
<7> [473.483836] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [473.486158] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [473.491103] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [473.492854] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [473.494425] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [473.496013] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [473.497544] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [473.499097] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [473.500646] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [473.502172] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [473.503770] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [473.505339] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [473.507074] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [473.508842] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [473.510498] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [473.512252] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [473.514200] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [473.580587] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [473.694808] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [473.695813] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [474.080253] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [474.081459] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<6> [474.550295] PM: suspend entry (s2idle)
<6> [474.555535] Filesystems sync: 0.005 seconds
<6> [474.561716] Freezing user space processes
<6> [474.566073] Freezing user space processes completed (elapsed 0.004 seconds)
<6> [474.566145] OOM killer disabled.
<6> [474.566150] Freezing remaining freezable tasks
<6> [474.568028] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<6> [474.589061] asix 1-1:1.0 enx00106031d5f9: Link is Down
<7> [474.611683] PM: suspend of devices complete after 29.240 msecs
<7> [474.611695] PM: start suspend of devices complete after 43.563 msecs
<7> [474.616376] PM: late suspend of devices complete after 4.674 msecs
<6> [474.640415] ACPI: EC: interrupt blocked
<7> [474.667241] PM: noirq suspend of devices complete after 33.684 msecs
<6> [474.668581] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<6> [474.670020] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [474.670028] PM: suspend-to-idle
<7> [489.660619] Timekeeping suspended for 14.516 seconds
<7> [489.663566] PM: Triggering wakeup from IRQ 9
<7> [489.664187] ACPI: PM: ACPI fixed event wakeup
<7> [489.664226] PM: resume from suspend-to-idle
<6> [489.667308] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [489.668633] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [489.670020] ACPI: EC: interrupt unblocked
<7> [489.686731] PM: noirq resume of devices complete after 18.087 msecs
<7> [489.704931] PM: early resume of devices complete after 2.202 msecs
<6> [490.012648] asix 1-1:1.0 enx00106031d5f9: configuring for phy/internal link mode
<7> [490.022207] PM: resume of devices complete after 317.179 msecs
<6> [490.040521] OOM killer enabled.
<6> [490.040559] Restarting tasks ... done.
<5> [490.063611] random: crng reseeded on system resumption
<6> [490.077347] PM: suspend exit
<6> [490.089965] [IGT] Re-loading i915
<7> [490.323881] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [490.324204] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [490.324418] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [490.324613] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [490.324972] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [490.325266] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [490.326153] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [490.326323] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [490.326469] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [490.326616] i915 0000:00:02.0: vgaarb: deactivate vga console
<7> [490.326870] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [490.327071] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [490.327576] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018
<7> [490.327798] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [490.328018] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [490.328219] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [490.328403] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [490.335991] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [490.336228] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [490.336438] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [490.336643] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [490.336849] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: LPDDR3
<7> [490.337037] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [490.337281] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [490.337514] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [490.337754] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [490.338008] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [490.338242] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [490.338480] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [490.338715] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [490.338955] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [490.339650] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [490.340002] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203
<7> [490.340333] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [490.340667] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [490.341017] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [490.341353] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [490.341687] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [490.342034] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [490.342366] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [490.342705] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [490.343058] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [490.343389] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [490.343716] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [490.344062] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [490.344384] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [490.344718] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [490.345060] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [490.345396] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [490.345713] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [490.346054] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [490.346379] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [490.346698] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [490.347032] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [490.347353] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [490.347679] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [490.348044] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [490.348469] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [490.348828] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [490.349174] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [490.349506] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [490.349827] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Max dotclock rate: 675000 kHz
<7> [490.350166] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [490.350611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [490.350929] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [490.351271] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [490.351614] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [490.352051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [490.352372] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [490.352704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [490.353043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [490.353428] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin
<6> [490.355361] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)
<7> [490.355799] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [490.356548] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [490.356865] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [490.357115] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [490.357414] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [490.357712] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [490.358167] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [490.358468] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [490.358677] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [490.358883] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [490.359129] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [490.362213] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [490.364726] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [490.366678] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT)
<7> [490.367035] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [490.373996] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [490.374236] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [490.374459] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [490.374677] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [490.374908] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [490.375162] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [490.375480] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP
<7> [490.375791] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [490.376116] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0
<7> [490.376430] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0
<7> [490.377001] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [490.377314] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [490.377537] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [490.377736] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [490.377934] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [490.378165] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [490.378408] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [490.378899] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [490.379141] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [490.379435] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [490.379655] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [490.379890] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [490.380131] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [490.585462] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [490.586885] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [490.588529] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40
<7> [490.591814] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [490.609072] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [490.609147] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [490.609200] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [490.609851] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.611681] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.613403] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:95:eDP-1] DRRS type: static
<7> [490.615355] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:95:eDP-1] Using native PCH PWM for backlight control
<7> [490.616898] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:95:eDP-1] backlight initialized, disabled, brightness 0/937
<7> [490.619043] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [490.620329] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [490.621633] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [490.623121] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [490.624566] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [490.625915] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [490.630147] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DDI B/PHY B] Using AUX CH B (VBT)
<7> [490.631766] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DDI B/PHY B]
<7> [490.635747] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [490.637214] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:102:DDI B/PHY B]
<7> [490.638460] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:102:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [490.641788] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:117:DDI C/PHY C] Using AUX CH C (VBT)
<7> [490.643465] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:117:DDI C/PHY C]
<7> [490.646709] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [490.648145] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:117:DDI C/PHY C]
<7> [490.649400] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:117:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [490.654201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [490.656438] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [490.658684] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [490.660301] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [490.661710] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [490.663413] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [490.665177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [490.666834] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [490.668392] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [490.670089] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [490.671710] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [490.673192] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [490.674827] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [490.676368] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [490.677889] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DP-MST A] hw state readout: disabled, pipe A
<7> [490.679561] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:105:DP-MST B] hw state readout: disabled, pipe B
<7> [490.681363] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP-MST C] hw state readout: disabled, pipe C
<7> [490.683193] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [490.684230] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
<7> [490.685254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
<7> [490.686135] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
<7> [490.686854] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [490.687819] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [490.688885] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [490.690003] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [490.691349] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:eDP-1] hw state readout: disabled
<7> [490.692190] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [490.692793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:112:HDMI-A-1] hw state readout: disabled
<7> [490.693563] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
<7> [490.694344] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:124:HDMI-A-2] hw state readout: disabled
<7> [490.695047] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [490.695695] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [490.696236] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [490.696796] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [490.697479] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [490.698186] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [490.698854] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [490.699555] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [490.700260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [490.700730] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [490.701196] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [490.701605] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [490.702373] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [490.702910] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [490.703467] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [490.704014] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [490.704422] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [490.704779] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [490.705252] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [490.705883] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [490.706352] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [490.706833] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [490.707387] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 GT workarounds on global
<7> [490.710735] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [490.711074] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [490.711430] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 context workarounds on rcs'0
<7> [490.734365] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [490.735443] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [490.735755] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [490.736062] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [490.736342] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [490.736598] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [490.737400] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [490.737641] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [490.737865] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [490.738106] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [490.744761] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:95:eDP-1] backlight device intel_backlight registered
<7> [490.745282] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [490.747903] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:eDP-1] generating connector hotplug event
<7> [490.748755] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [490.750165] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<7> [490.751031] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:112:HDMI-A-1] generating connector hotplug event
<7> [490.751811] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [490.753215] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:118:DP-2] generating connector hotplug event
<7> [490.754102] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:124:HDMI-A-2] generating connector hotplug event
<6> [490.754219] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [490.758379] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected
<6> [490.784913] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [490.792500] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input78
<7> [490.794129] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [490.795342] [drm:drm_client_modeset_probe]
<7> [490.795425] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [490.795344] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [490.795441] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [490.795721] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [490.796087] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [490.796396] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [490.797580] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [490.797911] i915 device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9
<7> [490.797919] i915 device info: graphics version: 9
<7> [490.797923] i915 device info: media version: 9
<7> [490.797928] i915 device info: graphics stepping: H0
<7> [490.797932] i915 device info: media stepping: H0
<7> [490.797979] i915 device info: display stepping: H0
<7> [490.797984] i915 device info: base die stepping: **
<7> [490.797988] i915 device info: gt: 2
<7> [490.797993] i915 device info: memory-regions: 0x21
<7> [490.797997] i915 device info: page-sizes: 0x11000
<7> [490.798001] i915 device info: platform: SKYLAKE
<7> [490.798005] i915 device info: ppgtt-size: 48
<7> [490.798010] i915 device info: ppgtt-type: 2
<7> [490.798014] i915 device info: dma_mask_size: 39
<7> [490.798018] i915 device info: is_mobile: no
<7> [490.798022] i915 device info: is_lp: no
<7> [490.798027] i915 device info: require_force_probe: no
<7> [490.798031] i915 device info: is_dgfx: no
<7> [490.798035] i915 device info: has_64bit_reloc: yes
<7> [490.798040] i915 device info: has_64k_pages: no
<7> [490.798044] i915 device info: gpu_reset_clobbers_display: no
<7> [490.798049] i915 device info: has_reset_engine: yes
<7> [490.798053] i915 device info: has_3d_pipeline: yes
<7> [490.798058] i915 device info: has_4tile: no
<7> [490.798062] i915 device info: has_flat_ccs: no
<7> [490.798067] i915 device info: has_global_mocs: no
<7> [490.798071] i915 device info: has_gmd_id: no
<7> [490.798076] i915 device info: has_gt_uc: yes
<7> [490.798080] i915 device info: has_heci_pxp: no
<7> [490.798084] i915 device info: has_heci_gscfi: no
<7> [490.798088] i915 device info: has_guc_deprivilege: no
<7> [490.798093] i915 device info: has_l3_ccs_read: no
<7> [490.798097] i915 device info: has_l3_dpf: no
<7> [490.798101] i915 device info: has_llc: yes
<7> [490.798105] i915 device info: has_logical_ring_contexts: yes
<7> [490.798110] i915 device info: has_logical_ring_elsq: no
<7> [490.798114] i915 device info: has_media_ratio_mode: no
<7> [490.798119] i915 device info: has_mslice_steering: no
<7> [490.798123] i915 device info: has_oa_bpc_reporting: no
<7> [490.798128] i915 device info: has_oa_slice_contrib_limits: no
<7> [490.798132] i915 device info: has_oam: no
<7> [490.798137] i915 device info: has_one_eu_per_fuse_bit: no
<7> [490.798141] i915 device info: has_pxp: no
<7> [490.798146] i915 device info: has_rc6: yes
<7> [490.798150] i915 device info: has_rc6p: no
<7> [490.798154] i915 device info: has_rps: yes
<7> [490.798159] i915 device info: has_runtime_pm: yes
<7> [490.798163] i915 device info: has_snoop: no
<7> [490.798167] i915 device info: has_coherent_ggtt: yes
<7> [490.798171] i915 device info: tuning_thread_rr_after_dep: no
<7> [490.798176] i915 device info: unfenced_needs_alignment: no
<7> [490.798180] i915 device info: hws_needs_physical: no
<7> [490.798184] i915 device info: has_pooled_eu: no
<7> [490.798188] i915 device info: rawclk rate: 24000 kHz
<7> [490.798194] i915 device info: display version: 9
<7> [490.798198] i915 device info: cursor_needs_physical: no
<7> [490.798203] i915 device info: has_cdclk_crawl: no
<7> [490.798207] i915 device info: has_cdclk_squash: no
<7> [490.798212] i915 device info: has_ddi: yes
<7> [490.798216] i915 device info: has_dp_mst: yes
<7> [490.798221] i915 device info: has_dsb: no
<7> [490.798225] i915 device info: has_fpga_dbg: yes
<7> [490.798230] i915 device info: has_gmch: no
<7> [490.798234] i915 device info: has_hotplug: yes
<7> [490.798238] i915 device info: has_hti: no
<7> [490.798242] i915 device info: has_ipc: yes
<7> [490.798247] i915 device info: has_overlay: no
<7> [490.798251] i915 device info: has_psr: yes
<7> [490.798255] i915 device info: has_psr_hw_tracking: yes
<7> [490.798259] i915 device info: overlay_needs_physical: no
<7> [490.798264] i915 device info: supports_tv: no
<7> [490.798268] i915 device info: has_hdcp: yes
<7> [490.798273] i915 device info: has_dmc: yes
<7> [490.798277] i915 device info: has_dsc: no
<7> [490.798282] i915 device info: iommu: disabled
<7> [490.798286] i915 device info: available engines: 40403
<7> [490.798291] i915 device info: slice total: 1, mask=0001
<7> [490.798297] i915 device info: subslice total: 3
<7> [490.798301] i915 device info: slice0: 3 subslices, mask=00000007
<7> [490.798306] i915 device info: slice1: 0 subslices, mask=00000000
<7> [490.798311] i915 device info: slice2: 0 subslices, mask=00000000
<7> [490.798316] i915 device info: EU total: 24
<7> [490.798320] i915 device info: EU per subslice: 8
<7> [490.798324] i915 device info: has slice power gating: no
<7> [490.798329] i915 device info: has subslice power gating: no
<7> [490.798333] i915 device info: has EU power gating: yes
<6> [490.798338] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [490.798343] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [490.798348] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [490.799047] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [490.799361] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [490.799654] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [490.799993] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [490.800315] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [490.800329] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [490.800340] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [490.800378] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [490.800678] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [490.801793] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [490.802135] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [490.803197] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [490.804158] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] status updated from unknown to connected
<7> [490.804527] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [490.804539] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.804552] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.804565] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [490.804579] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [490.805076] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] status updated from unknown to disconnected
<7> [490.805101] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [490.805191] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [490.805205] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [490.806611] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.806984] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [490.807519] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.807838] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.807850] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.808284] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [490.811870] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.811885] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [490.812324] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] status updated from unknown to disconnected
<7> [490.812355] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [490.812379] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [490.812392] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [490.812749] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] status updated from unknown to disconnected
<7> [490.812776] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [490.812797] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [490.812809] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [490.813516] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.813817] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [490.814475] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.814797] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.814808] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.815188] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [490.818828] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.818843] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [490.819247] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] status updated from unknown to disconnected
<7> [490.819277] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [490.819299] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [490.819309] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [490.819317] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [490.819325] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [490.819332] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [490.819401] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [490.819422] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [490.819430] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [490.819438] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [490.819445] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [490.819469] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [490.819514] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [490.819625] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [490.825467] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x000c0000
<6> [490.826611] fbcon: i915drmfb (fb0) is primary device
<6> [490.827255] Console: switching to colour frame buffer device 400x112
<6> [490.827277] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [490.841237] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [490.841252] [drm:drm_client_modeset_probe]
<7> [490.841333] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [490.841349] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [490.847121] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [490.847400] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [490.847644] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [490.847894] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [490.849424] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [490.849439] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [490.849450] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [490.849488] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [490.849754] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [490.853530] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [490.853817] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [490.856212] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [490.856227] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.856239] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.856251] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [490.856265] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [490.857065] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [490.857081] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [490.857094] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [490.858146] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.858431] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [490.859528] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [490.859837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.859850] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.861541] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<6> [490.864414] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [490.865344] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [490.865360] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [490.865649] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [490.865665] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [490.865678] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [490.866002] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [490.866014] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [490.866026] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [490.869027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.869312] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [490.869794] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [490.870094] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.870106] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [490.870349] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [490.873884] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [490.873899] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [490.874208] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [490.874222] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [490.874232] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [490.874240] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [490.874248] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [490.874255] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [490.874324] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [490.874344] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [490.874352] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [490.874360] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [490.874367] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [490.874398] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [490.875138] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:95:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [490.875461] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 373250KHz
<7> [490.875719] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [490.875985] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1119750 available 2160000
<7> [490.876252] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:95:eDP-1] SDP split enable: no
<7> [490.876506] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:51:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [490.876779] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:94:DDI A/PHY A] [CRTC:51:pipe A]
<7> [490.879258] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<6> [490.879442] [IGT] i915_suspend: finished subtest basic-s2idle-without-i915, SUCCESS
<7> [490.879574] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [490.879609] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [490.879849] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [490.880141] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [490.880414] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
<7> [490.880697] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [490.881003] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [490.881283] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [490.881564] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
<7> [490.881839] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [490.882205] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
<7> [490.882482] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [490.882759] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [490.883053] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [490.883321] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
<7> [490.883590] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [490.883861] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
<7> [490.884387] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [490.884663] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
<7> [490.884935] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [490.885242] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
<7> [490.885511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [490.885781] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
<7> [490.886075] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [490.886339] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [490.886609] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [490.886882] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
<7> [490.887183] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [490.887460] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
<7> [490.887733] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [490.888044] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
<7> [490.888320] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [490.888597] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [490.888876] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [490.889172] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000001)
<7> [490.889449] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [490.889722] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
<7> [490.890036] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
<7> [490.890308] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [490.890588] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [490.890915] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
<7> [490.894020] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 856), size 0 -> 856
<7> [490.894312] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36
<7> [490.894576] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
<7> [490.894841] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [490.895148] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0
<7> [490.895415] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0
<7> [490.895727] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (373250 kHz) > [CRTC:51:pipe A] min cdclk (0 kHz)
<7> [490.896034] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
<7> [490.896321] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [490.896598] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
<7> [490.896872] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [490.897174] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:51:pipe A] allocated DPLL 0
<7> [490.897447] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:51:pipe A] reserving DPLL 0
<7> [490.897724] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: yes [modeset]
<7> [490.898025] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [490.898300] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [490.898573] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [490.898850] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [490.899149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [490.899422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [490.899696] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
<7> [490.899993] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [490.900263] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [490.900530] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [490.900802] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0
<7> [490.900810] i915 0000:00:02.0: pixelformat: RGB
<7> [490.900818] i915 0000:00:02.0: colorimetry: sRGB
<7> [490.900825] i915 0000:00:02.0: bpc: 0
<7> [490.900832] i915 0000:00:02.0: dynamic range: VESA range
<7> [490.900839] i915 0000:00:02.0: content type: Not defined
<7> [490.900847] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [490.901140] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.901410] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [490.901680] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [490.901984] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [490.902256] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [490.902529] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
<7> [490.902798] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
<7> [490.903085] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [490.903359] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [490.903632] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [490.903907] i915 0000:00:02.0: [drm:skl_dump_hw_state [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
<7> [490.904204] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [490.904482] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [490.904763] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [490.905060] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [490.905334] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [490.905609] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [490.905884] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [490.906182] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:96] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [490.906459] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [490.906733] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [490.907031] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [490.907308] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [490.908030] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
<7> [490.909264] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [490.909548] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [490.909813] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [490.910098] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [490.910360] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [490.910621] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [490.910883] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [490.911169] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [490.911435] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [490.911707] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [490.912168] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [490.912458] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [490.912741] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [490.913202] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:51:pipe A]
<7> [490.913490] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [490.914095] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power on
<7> [490.914463] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [490.914790] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [490.915084] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [490.915361] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power on
<7> [490.915661] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000000b
<7> [491.116101] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [491.116732] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [491.118092] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [491.122890] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [491.124156] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [491.126585] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [491.127734] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [491.128862] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [491.132330] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Clock recovery OK
<7> [491.133653] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
<7> [491.135240] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS2
<7> [491.141596] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [491.143217] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [491.144814] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [491.149734] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [491.151246] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [491.154070] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [491.157426] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [491.159138] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [491.161725] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 937
<7> [491.164449] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, limit: 1
<7> [491.166232] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [491.172362] i915 0000:00:02.0: [drm:intel_pipe_update_end [i915]] Atomic update on pipe (A) took 489 us, max time under evasion is 250 us
<7> [491.175437] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
<7> [491.185433] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [491.187397] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [491.192138] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [491.194177] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<6> [491.201847] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [491.202602] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [491.203660] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [491.208145] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [491.209241] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<6> [491.223286] [IGT] i915_suspend: exiting, ret=0
<7> [491.224749] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [491.240551] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [491.240577] [drm:drm_client_modeset_probe]
<7> [491.240806] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1]
<7> [491.240836] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [491.244578] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [491.245190] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [491.245717] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [491.246299] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [491.246920] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [491.246990] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [491.247012] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [491.247124] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [491.247633] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [491.249061] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [491.249591] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [491.251843] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:eDP-1] probed modes :
<7> [491.251869] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [491.251896] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [491.251920] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1]
<7> [491.251993] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [491.252755] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:103:DP-1] disconnected
<7> [491.252779] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1]
<7> [491.252803] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [491.255237] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [491.255777] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [491.256555] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [491.257163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [491.257186] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [491.257718] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [491.262006] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [491.262029] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [491.262447] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [491.262480] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2]
<7> [491.262500] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [491.262930] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:118:DP-2] disconnected
<7> [491.263009] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2]
<7> [491.263026] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [491.263668] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [491.264014] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [491.264659] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [491.265161] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [491.265179] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [491.265576] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [491.269602] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [491.269635] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [491.270017] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [491.270034] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [491.270045] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [491.270054] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [491.270064] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [491.270072] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [491.270117] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [491.270146] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [491.270155] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [491.270165] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [491.270174] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [491.270219] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
|