Results for igt@i915_module_load@reload

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.28-gd991240f6 (x86_64) (Linux: 6.6.0-rc3-linus-v6.6-rc3-g6465e260f487+ x86_64)
Out 
Starting subtest: reload
Opened device: /dev/dri/card0
Subtest reload: SUCCESS (2.611s)
Err 
Starting subtest: reload
Subtest reload: SUCCESS (2.611s)
Dmesg
<6> [154.576132] [IGT] i915_module_load: executing
<6> [154.581578] [IGT] i915_module_load: starting subtest reload
<7> [154.690138] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [154.690574] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [154.691183] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [154.691855] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [154.692221] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [154.699889] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [154.700245] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [154.700568] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [154.700866] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [154.701167] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [154.701486] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [154.701783] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [154.702081] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [154.702449] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [154.703255] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [154.703640] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [154.703952] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [154.704252] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [154.705032] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [154.868425] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind
<7> [154.945923] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [154.946650] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [154.947687] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [154.949081] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [154.950444] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [154.951271] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [154.952150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [154.953216] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [155.003201] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [155.095993] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [156.290548] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [156.290851] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [156.291090] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [156.291579] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [156.291890] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [156.292075] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<6> [156.292709] i915 0000:00:02.0: [drm] Found 64MB of eDRAM
<7> [156.292841] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [156.293031] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [156.293196] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [156.293380] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [156.293388] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [156.293742] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [156.293766] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [156.293976] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [156.294509] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x7a9d1018
<7> [156.294755] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [156.294961] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [156.295164] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [156.295397] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [156.300354] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [156.300714] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [156.301051] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [156.301405] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [156.301780] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [156.302057] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 1, 16Gb DIMMs: no
<7> [156.302329] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [156.302605] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no
<7> [156.302877] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 1, 16Gb DIMMs: no
<7> [156.303143] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [156.303420] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no
<7> [156.303687] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [156.303952] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [156.304217] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [156.304898] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [156.305255] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 221
<7> [156.305635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [156.305995] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 317, min size 5)
<7> [156.306363] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [156.306719] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [156.307078] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [156.307447] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [156.307804] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [156.308164] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [156.308532] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [156.308893] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 22, min size 78)
<7> [156.309240] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [156.309599] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [156.309946] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [156.310303] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [156.310670] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [156.311027] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [156.311385] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [156.311735] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [156.312082] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [156.312445] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:1 USB-Type-C:0 TBT:0 DSC:0
<7> [156.312795] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [156.313142] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [156.313506] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:1 TBT:0 DSC:0
<7> [156.313860] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [156.314212] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [156.314576] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [156.314947] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [156.315402] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [156.315790] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [156.316149] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [156.317131] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [156.317507] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz
<7> [156.317886] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [156.318327] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [156.318596] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [156.318850] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [156.319082] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [156.319370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [156.319629] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [156.319846] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [156.320061] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [156.320325] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin
<7> [156.321010] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [156.321578] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [156.321796] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [156.322010] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [156.322216] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [156.322459] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [156.322765] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [156.323106] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [156.323425] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<6> [156.323658] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
<7> [156.323702] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [156.323914] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [156.326116] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [156.328243] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [156.328719] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] Using AUX CH A (VBT)
<7> [156.329061] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [156.334644] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [156.335019] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [156.335386] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [156.335737] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static
<7> [156.336101] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [156.336484] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [156.336833] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [156.337181] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [156.337536] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [156.337881] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 0, level 255, controller 0
<7> [156.338231] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1
<7> [156.338693] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [156.339099] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [156.339496] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [156.339832] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [156.340168] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [156.340516] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [156.340903] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [156.341578] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [156.341934] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [156.342354] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [156.342697] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [156.343068] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [156.343421] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [156.565097] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.580382] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.594036] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.606994] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.618354] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.629354] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.640353] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.651354] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.662354] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.673362] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.684352] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.695356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.707995] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.719356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.730356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.741357] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.752355] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.763355] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.774355] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.785353] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.796356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.807356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.818356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.829359] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.841000] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.852358] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.863355] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.874361] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.885353] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.896355] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.907354] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.918356] i915 0000:00:02.0: [drm:intel_dp_aux_xfer [i915]] AUX A/DDI A/PHY A: timeout (status 0x7d40023f)
<7> [156.918642] i915 0000:00:02.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX A/DDI A/PHY A: Too many retries, giving up. First error: -110
<6> [156.918660] i915 0000:00:02.0: [drm] [ENCODER:94:DDI A/PHY A] failed to retrieve link info, disabling eDP
<7> [156.918742] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD off
<7> [156.918986] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [156.919268] i915 0000:00:02.0: [drm:intel_ddi_init [i915]] VBT says port B has lspcon
<7> [156.919533] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] Using AUX CH B (VBT)
<7> [156.919882] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:94:DDI B/PHY B]
<7> [156.920670] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [156.920904] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:107:DDI C/PHY C] Using AUX CH C (VBT)
<7> [156.921146] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:107:DDI C/PHY C]
<7> [156.921808] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [156.922053] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:107:DDI C/PHY C]
<7> [156.922257] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:107:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [156.923033] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [156.923446] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [156.923731] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [156.923952] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [156.924170] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [156.924449] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [156.924799] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [156.925107] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [156.925327] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [156.925579] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [156.925840] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [156.926113] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [156.926473] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [156.926763] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:96:DP-MST A] hw state readout: disabled, pipe A
<7> [156.926973] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:97:DP-MST B] hw state readout: disabled, pipe B
<7> [156.927180] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DP-MST C] hw state readout: disabled, pipe C
<7> [156.927432] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:107:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [156.927716] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:109:DP-MST A] hw state readout: disabled, pipe A
<7> [156.928045] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DP-MST B] hw state readout: disabled, pipe B
<7> [156.928321] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:111:DP-MST C] hw state readout: disabled, pipe C
<7> [156.928578] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [156.928853] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [156.929075] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [156.929379] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [156.929791] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:DP-1] hw state readout: disabled
<7> [156.930113] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:108:DP-2] hw state readout: disabled
<7> [156.930438] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:114:HDMI-A-1] hw state readout: disabled
<7> [156.930704] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [156.930937] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [156.931170] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [156.931415] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [156.931692] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [156.931971] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [156.932219] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [156.932471] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [156.932711] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [156.932946] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [156.933155] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [156.933394] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [156.933718] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [156.933941] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [156.934212] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [156.934512] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [156.934751] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [156.934964] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [156.935172] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [156.935485] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [156.935658] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [156.935859] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [156.936071] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global
<7> [156.937678] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [156.937943] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [156.938172] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0
<7> [156.940066] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0
<7> [156.940986] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0
<7> [156.941692] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'1
<7> [156.942331] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0
<7> [156.958567] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [156.958991] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [156.959208] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [156.959652] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [156.959975] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [156.960236] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [156.960987] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [156.961230] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [156.961517] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [156.961772] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'1 to vcs1
<7> [156.961933] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [156.967687] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [156.969628] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [156.970629] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.972357] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.973681] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.976161] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.977707] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.978819] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: DP-HDMI ADAPTOR\004 (err 0)
<7> [156.979329] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.981405] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.982924] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.984584] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.986381] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.987790] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.988637] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode adaptor ID: a8 (err 0)
<7> [156.988655] i915 0000:00:02.0: [drm:lspcon_init [i915]] LSPCON detected
<7> [156.989675] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.991093] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.992556] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.994064] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.995883] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.997659] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [156.999649] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.001714] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.003324] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.004209] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [157.005197] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [157.005847] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [157.005866] i915 0000:00:02.0: [drm:lspcon_init [i915]] Vendor: Mega Chips
<7> [157.006086] i915 0000:00:02.0: [drm:lspcon_init [i915]] Success: LSPCON init
<7> [157.006901] i915 0000:00:02.0: [drm:lspcon_detect_hdr_capability [i915]] LSPCON capable of HDR
<7> [157.007129] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:DP-1] generating connector hotplug event
<7> [157.008058] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [157.009173] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:108:DP-2] generating connector hotplug event
<7> [157.009969] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:114:HDMI-A-1] generating connector hotplug event
<6> [157.010061] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [157.013209] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected
<6> [157.036905] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [157.041889] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input13
<7> [157.043247] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [157.044436] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [157.044813] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [157.045149] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [157.045505] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [157.046551] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [157.046872] i915 device info: pciid=0x5926 rev=0x06 platform=KABYLAKE (subplatform=0x1) gen=9
<7> [157.046877] i915 device info: graphics version: 9
<7> [157.046879] i915 device info: media version: 9
<7> [157.046882] i915 device info: graphics stepping: D1
<7> [157.046884] i915 device info: media stepping: D1
<7> [157.046887] i915 device info: display stepping: B1
<7> [157.046889] i915 device info: base die stepping: **
<7> [157.046891] i915 device info: gt: 3
<7> [157.046894] i915 device info: memory-regions: 0x21
<7> [157.046896] i915 device info: page-sizes: 0x11000
<7> [157.046898] i915 device info: platform: KABYLAKE
<7> [157.046901] i915 device info: ppgtt-size: 48
<7> [157.046903] i915 device info: ppgtt-type: 2
<7> [157.046905] i915 device info: dma_mask_size: 39
<7> [157.046908] i915 device info: is_mobile: no
<7> [157.046910] i915 device info: is_lp: no
<7> [157.046913] i915 device info: require_force_probe: no
<7> [157.046915] i915 device info: is_dgfx: no
<7> [157.046917] i915 device info: has_64bit_reloc: yes
<7> [157.046920] i915 device info: has_64k_pages: no
<7> [157.046922] i915 device info: gpu_reset_clobbers_display: no
<7> [157.046924] i915 device info: has_reset_engine: yes
<7> [157.046927] i915 device info: has_3d_pipeline: yes
<7> [157.046929] i915 device info: has_4tile: no
<7> [157.046931] i915 device info: has_flat_ccs: no
<7> [157.046934] i915 device info: has_global_mocs: no
<7> [157.046936] i915 device info: has_gmd_id: no
<7> [157.046938] i915 device info: has_gt_uc: yes
<7> [157.046941] i915 device info: has_heci_pxp: no
<7> [157.046943] i915 device info: has_heci_gscfi: no
<7> [157.046945] i915 device info: has_guc_deprivilege: no
<7> [157.046948] i915 device info: has_l3_ccs_read: no
<7> [157.046950] i915 device info: has_l3_dpf: no
<7> [157.046952] i915 device info: has_llc: yes
<7> [157.046954] i915 device info: has_logical_ring_contexts: yes
<7> [157.046957] i915 device info: has_logical_ring_elsq: no
<7> [157.046959] i915 device info: has_media_ratio_mode: no
<7> [157.046962] i915 device info: has_mslice_steering: no
<7> [157.046964] i915 device info: has_oa_bpc_reporting: no
<7> [157.046966] i915 device info: has_oa_slice_contrib_limits: no
<7> [157.046969] i915 device info: has_oam: no
<7> [157.046971] i915 device info: has_one_eu_per_fuse_bit: no
<7> [157.046973] i915 device info: has_pxp: no
<7> [157.046975] i915 device info: has_rc6: yes
<7> [157.046978] i915 device info: has_rc6p: no
<7> [157.046980] i915 device info: has_rps: yes
<7> [157.046982] i915 device info: has_runtime_pm: yes
<7> [157.046985] i915 device info: has_snoop: no
<7> [157.046987] i915 device info: has_coherent_ggtt: yes
<7> [157.046989] i915 device info: tuning_thread_rr_after_dep: no
<7> [157.046992] i915 device info: unfenced_needs_alignment: no
<7> [157.046994] i915 device info: hws_needs_physical: no
<7> [157.046996] i915 device info: has_pooled_eu: no
<7> [157.046999] i915 device info: rawclk rate: 24000 kHz
<7> [157.047001] i915 device info: display version: 9
<7> [157.047004] i915 device info: cursor_needs_physical: no
<7> [157.047006] i915 device info: has_cdclk_crawl: no
<7> [157.047008] i915 device info: has_cdclk_squash: no
<7> [157.047011] i915 device info: has_ddi: yes
<7> [157.047013] i915 device info: has_dp_mst: yes
<7> [157.047015] i915 device info: has_dsb: no
<7> [157.047017] i915 device info: has_fpga_dbg: yes
<7> [157.047020] i915 device info: has_gmch: no
<7> [157.047022] i915 device info: has_hotplug: yes
<7> [157.047024] i915 device info: has_hti: no
<7> [157.047027] i915 device info: has_ipc: yes
<7> [157.047029] i915 device info: has_overlay: no
<7> [157.047031] i915 device info: has_psr: yes
<7> [157.047033] i915 device info: has_psr_hw_tracking: yes
<7> [157.047036] i915 device info: overlay_needs_physical: no
<7> [157.047038] i915 device info: supports_tv: no
<7> [157.047040] i915 device info: has_hdcp: yes
<7> [157.047043] i915 device info: has_dmc: yes
<7> [157.047045] i915 device info: has_dsc: no
<7> [157.047047] i915 device info: iommu: enabled
<7> [157.047050] i915 device info: available engines: 40c03
<7> [157.047053] i915 device info: slice total: 2, mask=0003
<7> [157.047055] i915 device info: subslice total: 6
<7> [157.047058] i915 device info: slice0: 3 subslices, mask=00000007
<7> [157.047061] i915 device info: slice1: 3 subslices, mask=00000007
<7> [157.047063] i915 device info: slice2: 0 subslices, mask=00000000
<7> [157.047066] i915 device info: EU total: 48
<7> [157.047068] i915 device info: EU per subslice: 8
<7> [157.047070] i915 device info: has slice power gating: yes
<7> [157.047072] i915 device info: has subslice power gating: no
<7> [157.047075] i915 device info: has EU power gating: yes
<6> [157.047077] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [157.047080] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [157.047083] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [157.047365] [drm:drm_client_modeset_probe]
<7> [157.047432] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [157.047446] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [157.049547] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [157.049936] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [157.051423] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.052940] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.054663] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.056021] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.058235] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.060195] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.062127] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.064651] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.066054] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.066973] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [157.068299] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [157.069301] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [157.070003] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [157.070587] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [157.070838] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [157.071061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [157.071766] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [157.072190] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] status updated from unknown to disconnected
<7> [157.072208] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [157.072387] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2]
<7> [157.072400] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [157.072827] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [157.073431] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [157.073721] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] status updated from unknown to disconnected
<7> [157.073738] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected
<7> [157.073745] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [157.073752] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<7> [157.073971] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [157.126410] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [157.144015] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [157.144025] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [157.144254] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [157.160187] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [157.160195] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [157.160423] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [157.160692] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] status updated from unknown to disconnected
<7> [157.160711] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [157.160718] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [157.160724] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [157.160728] [drm:drm_client_modeset_probe] connector 108 enabled? no
<7> [157.160732] [drm:drm_client_modeset_probe] connector 114 enabled? no
<7> [157.160773] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [157.160784] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [157.160805] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [157.160814] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [157.161419] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [157.161703] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [157.162286] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [157.163402] [drm:drm_client_modeset_probe]
<7> [157.163458] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [157.163471] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<7> [157.163935] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [157.165193] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [157.165556] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [157.166630] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.168269] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.169877] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<6> [157.170419] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [157.171378] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.173205] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [157.173957] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.174310] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [157.176869] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [157.177298] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.179375] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.181335] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.182759] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.185229] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON
<7> [157.186298] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04
<7> [157.187251] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000
<7> [157.187940] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [157.188714] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected
<7> [157.188744] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2]
<7> [157.188756] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2]
<7> [157.189111] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected
<7> [157.189121] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1]
<7> [157.189131] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1]
<6> [157.192957] [IGT] i915_module_load: finished subtest reload, SUCCESS
<6> [157.193127] [IGT] i915_module_load: exiting, ret=0
<7> [157.241552] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [157.244900] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [157.244912] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [157.245148] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [157.248313] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [157.248322] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [157.248627] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [157.248895] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [157.249157] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [157.249894] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [157.250334] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected
<7> [157.250363] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [157.250371] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [157.250377] [drm:drm_client_modeset_probe] connector 108 enabled? no
<7> [157.250382] [drm:drm_client_modeset_probe] connector 114 enabled? no
<7> [157.250437] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [157.250452] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [157.250481] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [157.250494] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [157.250588] [drm:drm_client_modeset_probe]
<7> [157.250716] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1]
<7> [157.250726] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1]
<6> [157.250737] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [157.251081] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [157.251516] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [157.251911] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [157.252529] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [157.252998] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [157.253526] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2
<7> [157.253986] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms
<7> [157.255255] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.256990] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.258748] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.260752] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.262757] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.264662] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
<7> [157.266776] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer
Created at 2023-09-24 23:29:06