Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.28-g2aaeef0cd (x86_64) (Linux: 6.6.0-rc2-linus-v6.6-rc2-gce9ecca0238b+ x86_64) |
| Out |
Starting subtest: basic-s2idle-without-i915 Opened device: /dev/dri/card0 [cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Sun Sep 17 22:07:59 2023 Subtest basic-s2idle-without-i915: SUCCESS (8.125s) |
| Err |
Starting subtest: basic-s2idle-without-i915 Subtest basic-s2idle-without-i915: SUCCESS (8.125s) |
| Dmesg |
<6> [541.734325] [IGT] i915_suspend: executing
<6> [541.739037] [IGT] i915_suspend: starting subtest basic-s2idle-without-i915
<7> [541.973419] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [541.973951] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [541.974351] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [541.974763] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [541.975337] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [541.975740] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz
<7> [541.976777] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [541.977092] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [541.977901] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [541.978211] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [541.978506] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [541.978829] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [541.978838] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [541.979721] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [541.979758] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [541.980106] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [541.980874] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [541.981284] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [541.981654] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [541.982003] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [541.982345] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [541.992298] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [541.992732] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [541.993082] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [541.993423] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [541.993786] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [541.994138] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [541.994472] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [541.994792] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [541.995108] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [541.995403] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [541.995700] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [541.996002] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [541.996443] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [541.996793] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [541.997098] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [541.997483] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [541.997874] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [541.998241] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [541.998609] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [541.999013] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [541.999397] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [541.999775] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [542.000135] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [542.000489] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [542.000882] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [542.001263] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [542.001638] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [542.002001] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [542.002353] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [542.002725] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [542.003110] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [542.003482] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [542.003859] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [542.004218] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [542.004569] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [542.007983] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [542.008402] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [542.008798] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [542.009203] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [542.009587] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [542.009994] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [542.010367] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [542.010742] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [542.011110] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [542.011503] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [542.011906] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [542.012282] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [542.012655] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [542.013010] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [542.013381] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [542.013774] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [542.014148] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [542.014516] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [542.014885] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [542.015249] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [542.015646] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [542.016021] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [542.016375] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [542.016735] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [542.017088] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [542.017454] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [542.017851] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [542.018212] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [542.018569] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [542.018979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [542.019372] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [542.019788] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [542.020185] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [542.020556] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [542.020931] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [542.021296] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [542.021792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [542.022234] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [542.022602] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [542.023129] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [542.023491] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [542.023878] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [542.024304] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [542.024700] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [542.025072] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [542.025431] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [542.025809] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [542.026192] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [542.026569] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [542.026963] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [542.027455] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [542.027980] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<7> [542.031370] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [542.032344] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [542.032754] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [542.033125] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [542.033500] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<6> [542.033928] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<7> [542.034034] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [542.034394] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [542.034752] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [542.035101] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [542.035466] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [542.040558] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [542.046257] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [542.046838] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [542.047234] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [542.047703] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT)
<7> [542.048114] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [542.055648] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [542.056098] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [542.056491] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [542.056916] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [542.057337] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [542.057759] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [542.058136] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [542.058508] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [542.058910] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [542.059288] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [542.059824] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [542.060286] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [542.060692] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [542.061047] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [542.061397] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [542.061775] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [542.062246] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [542.062795] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [542.063449] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [542.063877] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [542.064341] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [542.064745] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [542.065167] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [542.065546] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [542.271002] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [542.271859] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [542.272734] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [542.274421] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [542.282064] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.283961] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.285921] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.288412] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.290332] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.292274] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.294268] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.296089] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [542.297746] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [542.297784] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [542.297805] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [542.298037] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [542.299014] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [542.299918] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)
<7> [542.309593] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [542.310859] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7> [542.311847] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000
<7> [542.312977] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [542.313847] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [542.314693] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [542.315527] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [542.316395] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [542.317351] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [542.319563] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT)
<7> [542.320522] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [542.322363] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [542.323268] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [542.324148] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [542.325778] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [542.326599] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)
<7> [542.329372] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [542.330581] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [542.331768] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<7> [542.332692] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [542.333590] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [542.334505] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [542.335400] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [542.336303] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [542.337294] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [542.338202] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [542.339098] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [542.339984] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [542.340977] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [542.341896] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [542.342788] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [542.343679] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [542.344549] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [542.345477] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [542.346394] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [542.347262] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [542.348052] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [542.348880] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [542.349701] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [542.350456] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [542.351258] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [542.352064] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [542.352869] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [542.353696] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [542.354385] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [542.355028] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [542.355654] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [542.356244] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [542.356924] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [542.357575] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [542.358362] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [542.359038] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [542.359830] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [542.360462] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [542.361142] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [542.361875] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [542.362477] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [542.363115] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [542.363735] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [542.364335] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [542.364990] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [542.365603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [542.366195] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [542.366657] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [542.367091] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [542.367559] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<7> [542.368053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [542.368515] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [542.369117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [542.369560] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [542.370020] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [542.370470] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [542.370962] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [542.371411] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [542.371904] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [542.372340] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [542.372819] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [542.373249] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [542.373603] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [542.373968] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [542.374314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [542.374668] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [542.375025] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [542.399417] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [542.399859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [542.400222] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [542.400577] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [542.401026] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [542.401925] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [542.402876] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [542.403351] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [542.403868] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [542.403903] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [542.407524] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0
<7> [542.408111] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [542.408531] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [542.412169] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [542.413277] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [542.414376] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [542.432609] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [542.433144] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [542.433513] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [542.433896] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [542.434357] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [542.435925] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [542.436265] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [542.436568] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [542.436886] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [542.442832] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [542.443443] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [542.445886] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [542.446674] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [542.448184] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [542.448929] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [542.449602] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [542.449728] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [542.453534] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [542.484642] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [542.492125] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input60
<7> [542.493497] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)
<7> [542.494739] [drm:drm_client_modeset_probe]
<7> [542.494816] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [542.494680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [542.494833] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [542.496153] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [542.496598] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [542.496606] i915 device info: graphics version: 11
<7> [542.496610] i915 device info: media version: 11
<7> [542.496614] i915 device info: graphics stepping: B0
<7> [542.496638] i915 device info: media stepping: B0
<7> [542.496642] i915 device info: display stepping: B0
<7> [542.496646] i915 device info: base die stepping: **
<7> [542.496649] i915 device info: gt: 0
<7> [542.496653] i915 device info: memory-regions: 0x21
<7> [542.496656] i915 device info: page-sizes: 0x211000
<7> [542.496660] i915 device info: platform: JASPERLAKE
<7> [542.496664] i915 device info: ppgtt-size: 36
<7> [542.496667] i915 device info: ppgtt-type: 2
<7> [542.496671] i915 device info: dma_mask_size: 39
<7> [542.496674] i915 device info: is_mobile: no
<7> [542.496678] i915 device info: is_lp: no
<7> [542.496682] i915 device info: require_force_probe: no
<7> [542.496685] i915 device info: is_dgfx: no
<7> [542.496689] i915 device info: has_64bit_reloc: yes
<7> [542.496692] i915 device info: has_64k_pages: no
<7> [542.496696] i915 device info: gpu_reset_clobbers_display: no
<7> [542.496699] i915 device info: has_reset_engine: yes
<7> [542.496703] i915 device info: has_3d_pipeline: yes
<7> [542.496706] i915 device info: has_4tile: no
<7> [542.496710] i915 device info: has_flat_ccs: no
<7> [542.496713] i915 device info: has_global_mocs: no
<7> [542.496716] i915 device info: has_gmd_id: no
<7> [542.496720] i915 device info: has_gt_uc: yes
<7> [542.496723] i915 device info: has_heci_pxp: no
<7> [542.496726] i915 device info: has_heci_gscfi: no
<7> [542.496729] i915 device info: has_guc_deprivilege: no
<7> [542.496733] i915 device info: has_l3_ccs_read: no
<7> [542.496737] i915 device info: has_l3_dpf: no
<7> [542.496740] i915 device info: has_llc: yes
<7> [542.496743] i915 device info: has_logical_ring_contexts: yes
<7> [542.496747] i915 device info: has_logical_ring_elsq: yes
<7> [542.496750] i915 device info: has_media_ratio_mode: no
<7> [542.496753] i915 device info: has_mslice_steering: no
<7> [542.496757] i915 device info: has_oa_bpc_reporting: no
<7> [542.496760] i915 device info: has_oa_slice_contrib_limits: no
<7> [542.496763] i915 device info: has_oam: no
<7> [542.496766] i915 device info: has_one_eu_per_fuse_bit: no
<7> [542.496770] i915 device info: has_pxp: no
<7> [542.496773] i915 device info: has_rc6: yes
<7> [542.496776] i915 device info: has_rc6p: no
<7> [542.496779] i915 device info: has_rps: yes
<7> [542.496782] i915 device info: has_runtime_pm: yes
<7> [542.496786] i915 device info: has_snoop: no
<7> [542.496789] i915 device info: has_coherent_ggtt: no
<7> [542.496792] i915 device info: tuning_thread_rr_after_dep: no
<7> [542.496795] i915 device info: unfenced_needs_alignment: no
<7> [542.496799] i915 device info: hws_needs_physical: no
<7> [542.496802] i915 device info: has_pooled_eu: no
<7> [542.496805] i915 device info: rawclk rate: 19200 kHz
<7> [542.496809] i915 device info: display version: 11
<7> [542.496813] i915 device info: cursor_needs_physical: no
<7> [542.496816] i915 device info: has_cdclk_crawl: no
<7> [542.496820] i915 device info: has_cdclk_squash: no
<7> [542.496823] i915 device info: has_ddi: yes
<7> [542.496826] i915 device info: has_dp_mst: yes
<7> [542.496829] i915 device info: has_dsb: no
<7> [542.496832] i915 device info: has_fpga_dbg: yes
<7> [542.496836] i915 device info: has_gmch: no
<7> [542.496839] i915 device info: has_hotplug: yes
<7> [542.496842] i915 device info: has_hti: no
<7> [542.496845] i915 device info: has_ipc: yes
<7> [542.496849] i915 device info: has_overlay: no
<7> [542.496852] i915 device info: has_psr: yes
<7> [542.496855] i915 device info: has_psr_hw_tracking: yes
<7> [542.496858] i915 device info: overlay_needs_physical: no
<7> [542.496862] i915 device info: supports_tv: no
<7> [542.496865] i915 device info: has_hdcp: no
<7> [542.496868] i915 device info: has_dmc: yes
<7> [542.496871] i915 device info: has_dsc: yes
<7> [542.496875] i915 device info: iommu: enabled
<7> [542.496879] i915 device info: available engines: 40403
<7> [542.496883] i915 device info: slice total: 1, mask=0001
<7> [542.496887] i915 device info: subslice total: 4
<7> [542.496891] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [542.496895] i915 device info: EU total: 16
<7> [542.496898] i915 device info: EU per subslice: 4
<7> [542.496902] i915 device info: has slice power gating: yes
<7> [542.496905] i915 device info: has subslice power gating: yes
<7> [542.496908] i915 device info: has EU power gating: yes
<6> [542.496912] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [542.496917] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [542.496921] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<6> [542.497159] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [542.500451] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [542.500931] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [542.501297] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [542.504727] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [542.505157] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [542.505172] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [542.505181] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [542.505218] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [542.505579] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [542.510530] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [542.511007] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [542.512250] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [542.513102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [542.514383] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to connected
<7> [542.515077] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [542.515091] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [542.515103] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [542.515115] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [542.515129] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [542.516040] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [542.516069] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [542.516083] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [542.516095] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [542.516538] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [542.516558] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [542.516569] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [542.516580] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [542.517276] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [542.517303] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [542.517321] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [542.517330] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [542.517336] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [542.517342] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [542.517414] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [542.517435] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [542.517442] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [542.517448] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [542.517454] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [542.517475] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<7> [542.517512] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [542.517861] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<6> [542.536859] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [542.536844] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00180000
<6> [542.538111] fbcon: i915drmfb (fb0) is primary device
<6> [542.539104] Console: switching to colour frame buffer device 400x112
<6> [542.539131] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [542.544785] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [542.544804] [drm:drm_client_modeset_probe]
<7> [542.544864] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [542.544881] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [542.548683] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [542.549121] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [542.549497] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [542.551647] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [542.552096] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [542.552111] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [542.552121] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [542.552156] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [542.552527] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [542.554690] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [542.555104] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [542.558385] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [542.558403] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [542.558415] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [542.558427] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [542.558440] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [542.559721] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [542.559740] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [542.559753] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [542.560211] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [542.560225] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [542.560236] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [542.561092] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [542.561109] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [542.561119] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [542.561126] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [542.561132] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [542.561195] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [542.561215] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [542.561223] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [542.561229] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [542.561235] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [542.561263] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<7> [542.562138] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [542.562600] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz
<7> [542.563244] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [542.563615] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000
<7> [542.564162] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no
<7> [542.564526] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long
<7> [542.566612] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [542.567055] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]
<7> [542.567418] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [542.567813] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [542.568202] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [542.568590] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [542.569228] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288)
<7> [542.569611] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [542.570549] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [542.571120] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [542.571492] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316)
<7> [542.572037] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [542.572426] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316)
<7> [542.573008] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [542.573387] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [542.574210] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [542.574590] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816)
<7> [542.575121] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [542.575492] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816)
<7> [542.576011] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802)
<7> [542.576377] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807)
<7> [542.577077] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [542.577455] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316)
<7> [542.578017] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [542.578404] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316)
<7> [542.578976] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [542.579347] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [542.579942] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [542.580314] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816)
<7> [542.580880] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [542.581265] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816)
<7> [542.581791] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802)
<7> [542.582160] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807)
<7> [542.582540] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [542.583146] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [542.583612] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [542.584178] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b)
<7> [542.584542] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x00e001a5)
<7> [542.585064] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [542.585425] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310)
<7> [542.585967] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310)
<7> [542.586329] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [542.586843] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [542.587369] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1
<7> [542.587988] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985
<7> [542.588370] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39
<7> [542.588931] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [542.589297] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [542.589808] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0
<7> [542.590180] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0
<7> [542.590558] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1
<7> [542.591144] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446
<7> [542.591522] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446
<7> [542.592060] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446
<7> [542.592475] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz)
<7> [542.593027] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)
<7> [542.593418] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [542.593936] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [542.594303] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [542.594847] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0
<7> [542.595161] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0
<7> [542.595484] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]
<7> [542.595996] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [542.596321] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [542.596868] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [542.597182] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [542.597489] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [542.598017] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [542.598349] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64
<7> [542.598843] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [542.599152] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [542.599458] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [542.600003] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [542.600321] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [542.600797] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [542.601115] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa
<7> [542.601435] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa
<7> [542.601936] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa
<6> [542.602231] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100
<7> [542.602255] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310
<7> [542.602560] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0
<7> [542.602894] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [542.603201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [542.603506] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [542.604078] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [542.604403] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [542.604943] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [542.605255] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [542.605553] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [542.606017] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [542.606320] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [542.606781] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [542.607087] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [542.607388] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [542.607843] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [542.608150] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [542.608456] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [542.608954] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [542.609273] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [542.609604] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [542.610105] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
<7> [542.610418] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
<7> [542.610954] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
<7> [542.611271] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
<7> [542.611581] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no
<7> [542.612083] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no
<7> [542.612390] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no
<7> [542.613263] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1
<7> [542.614342] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]
<7> [542.614779] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]
<7> [542.615090] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]
<7> [542.615392] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]
<7> [542.615715] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]
<7> [542.616009] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]
<7> [542.616302] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [542.616801] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [542.617119] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4
<7> [542.617579] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]
<6> [542.617953] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [542.618198] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [542.619936] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on
<7> [542.620439] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [542.621022] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [542.621415] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [542.621908] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on
<7> [542.622276] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b
<7> [542.684024] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [542.832990] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [542.833914] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [542.839233] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [542.839356] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [542.840885] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [542.841890] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [542.844193] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [542.844952] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [542.847350] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK
<7> [542.848170] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [542.851084] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1
<7> [542.851810] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1
<7> [542.854474] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [542.855212] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [542.856550] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [542.858346] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [542.859104] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [542.860204] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000
<7> [542.869947] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1
<7> [542.870782] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [542.875848] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]
<7> [542.876781] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]
<7> [542.878959] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0
<7> [542.879723] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [542.880483] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [542.884030] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [542.884060] [drm:drm_client_modeset_probe]
<7> [542.884195] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<6> [542.884029] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [542.884228] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [542.884971] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [542.886154] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [542.888157] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x810
<7> [542.888563] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [542.889227] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [542.889902] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [542.890530] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [542.891365] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [542.891394] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [542.891414] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [542.891484] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [542.892162] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [542.895937] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [542.896471] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [542.898144] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [542.898168] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [542.898188] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [542.898208] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [542.898229] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [542.898875] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [542.898899] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [542.898918] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [542.899497] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [542.899519] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [542.899536] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [542.900143] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [542.900160] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [542.900173] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [542.900182] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [542.900190] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [542.900278] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [542.900306] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [542.900316] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [542.900325] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [542.900333] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [542.900371] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<6> [542.927131] [IGT] Unloading i915
<6> [542.932030] Console: switching to colour dummy device 80x25
<4> [543.913998] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x200f0000
<4> [544.916996] snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x200f0000
<4> [545.922997] snd_hda_intel 0000:00:1f.3: Codec #2 probe error; disabling it...
<7> [545.926786] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [545.927680] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067
<6> [545.935791] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC700: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
<6> [545.935813] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [545.935819] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [545.935825] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [545.935829] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [545.935834] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19
<6> [546.710937] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [546.727451] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input61
<6> [546.739940] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input62
<7> [546.749240] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [546.749735] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [546.750070] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [546.750399] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [546.751050] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [546.884910] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [546.885734] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [546.886522] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [546.887368] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [546.888187] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [546.889015] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [546.889974] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [546.890764] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [546.891488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [546.892282] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [546.893103] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [546.896859] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)
<7> [546.897680] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 1, found 0)
<7> [546.898408] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)
<7> [546.899402] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [546.900780] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0)
<7> [546.901527] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [546.902837] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [546.903563] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)
<7> [546.904285] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3316, found 0)
<7> [546.904918] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)
<7> [546.905511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0)
<7> [546.906282] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)
<7> [546.906902] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)
<7> [546.907478] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [546.908082] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1816, found 0)
<7> [546.908671] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [546.909237] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0)
<7> [546.909864] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0)
<7> [546.910456] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0)
<7> [546.911038] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)
<7> [546.911516] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3316, found 0)
<7> [546.912017] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)
<7> [546.912490] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0)
<7> [546.913049] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)
<7> [546.913533] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)
<7> [546.914034] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [546.914508] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0)
<7> [546.915010] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [546.915483] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0)
<7> [546.915985] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0)
<7> [546.916476] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0)
<7> [546.916981] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [546.917457] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [546.917958] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [546.918344] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [546.918726] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 361310, found 0)
<7> [546.919084] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 361310, found 0)
<7> [546.919442] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [546.919853] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [546.920233] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0
<7> [546.920672] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [546.921135] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0
<7> [546.921474] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0
<7> [546.921836] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [546.922190] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [546.922544] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [546.922921] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [546.923277] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0
<7> [546.923671] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0
<7> [546.924040] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0
<7> [546.924392] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0
<7> [546.924838] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [546.925200] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz
<7> [546.925514] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
<7> [546.925873] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset]
<7> [546.926183] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
<7> [546.926483] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
<7> [546.926801] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
<7> [546.927104] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
<7> [546.927413] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
<7> [546.927756] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no
<7> [546.928067] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no
<7> [546.928365] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no
<7> [546.950850] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [547.157072] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0
<7> [547.158526] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [547.163125] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [547.163982] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [547.166950] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off
<7> [547.167718] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [547.168442] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [547.171740] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [547.172501] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [547.173327] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [547.174395] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [547.192381] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [547.193180] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [547.193869] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [547.194694] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [547.221015] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [547.221928] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [547.222777] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [547.223584] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [547.223701] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A]
<7> [547.224345] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30
<7> [547.224717] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
<7> [547.225156] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [547.225480] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [547.226280] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [547.227404] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [547.228918] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]
<7> [547.229700] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]
<7> [547.230391] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]
<7> [547.231115] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]
<7> [547.231856] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]
<7> [547.232544] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]
<7> [547.233352] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]
<7> [547.234140] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [547.234918] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [547.235687] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4
<7> [547.236538] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]
<7> [547.284949] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [547.382953] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [547.384337] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [547.829158] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [547.830009] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<6> [548.328869] PM: suspend entry (s2idle)
<6> [548.337112] Filesystems sync: 0.008 seconds
<6> [548.344481] Freezing user space processes
<6> [548.348594] Freezing user space processes completed (elapsed 0.004 seconds)
<6> [548.348709] OOM killer disabled.
<6> [548.348715] Freezing remaining freezable tasks
<6> [548.350426] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<7> [548.607077] PM: suspend of devices complete after 227.586 msecs
<7> [548.607114] PM: start suspend of devices complete after 256.574 msecs
<7> [548.614496] PM: late suspend of devices complete after 7.368 msecs
<6> [548.620107] ACPI: EC: interrupt blocked
<7> [548.645077] PM: noirq suspend of devices complete after 28.991 msecs
<6> [548.645165] ACPI: \_SB_.PR00: LPI: Device not power manageable
<6> [548.645219] ACPI: \_SB_.PR01: LPI: Device not power manageable
<6> [548.645261] ACPI: \_SB_.PR02: LPI: Device not power manageable
<6> [548.645300] ACPI: \_SB_.PR03: LPI: Device not power manageable
<6> [548.645338] ACPI: \_SB_.PC00.GFX0: LPI: Device not power manageable
<6> [548.645396] ACPI: \_SB_.PC00.PSDC: LPI: Constraint not met; min power state:D3hot current power state:D0
<6> [548.645457] ACPI: \_SB_.PC00.RP05.PXSX: LPI: Device not power manageable
<6> [548.645497] ACPI: \_SB_.PC00.IPU0: LPI: Device not power manageable
<6> [548.645534] ACPI: \_SB_.PC00.HECI: LPI: Device not power manageable
<6> [548.653196] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<7> [548.670068] PM: Triggering wakeup from IRQ 9
<6> [548.673943] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [548.673957] PM: suspend-to-idle
<7> [548.674123] ACPI: EC: ACPI EC GPE status set
<7> [548.674187] ACPI: PM: Rearming ACPI SCI for wakeup
<7> [563.657716] Timekeeping suspended for 14.837 seconds
<7> [563.657792] PM: Triggering wakeup from IRQ 9
<7> [563.658593] ACPI: PM: ACPI fixed event wakeup
<7> [563.658610] PM: resume from suspend-to-idle
<6> [563.682048] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [563.685780] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [563.687712] ACPI: EC: interrupt unblocked
<7> [563.713122] PM: noirq resume of devices complete after 27.326 msecs
<7> [563.719132] PM: early resume of devices complete after 3.822 msecs
<6> [563.731704] serial 00:03: activated
<6> [563.872584] r8152 1-1:1.0 enx00e04c680709: carrier on
<6> [563.889392] r8169 0000:01:00.0 enp1s0: Link is Down
<7> [563.890606] PM: resume of devices complete after 171.461 msecs
<6> [563.897435] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [563.897483] OOM killer enabled.
<6> [563.897498] Restarting tasks ... done.
<5> [563.914644] random: crng reseeded on system resumption
<6> [563.958488] PM: suspend exit
<3> [563.963419] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
<6> [563.968612] [IGT] Re-loading i915
<6> [563.986964] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [564.035393] ata2: SATA link down (SStatus 4 SControl 300)
<7> [564.235324] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [564.235829] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [564.236278] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [564.236714] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [564.237353] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [564.237750] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz
<7> [564.238951] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [564.239314] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [564.240245] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [564.240582] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [564.240893] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [564.241239] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [564.241249] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [564.242130] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [564.242171] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [564.242575] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [564.243439] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [564.243898] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [564.244308] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [564.244688] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [564.245085] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [564.252985] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [564.253419] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [564.253800] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [564.254207] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [564.254622] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [564.255003] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [564.255328] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [564.255642] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [564.255975] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [564.256282] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [564.256591] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [564.256887] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [564.257355] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [564.257673] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [564.258037] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [564.258434] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [564.258824] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [564.259229] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [564.259608] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [564.260036] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [564.260429] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [564.260815] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [564.261228] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [564.261617] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [564.262001] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [564.262388] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [564.262781] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [564.263206] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [564.263572] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [564.263990] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [564.264360] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [564.264720] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [564.265114] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [564.265545] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [564.266002] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [564.267579] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [564.268018] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [564.268419] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [564.268833] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [564.269538] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [564.269956] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [564.270452] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [564.270859] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [564.271322] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [564.271718] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [564.272129] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [564.272507] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [564.272896] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [564.273325] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [564.273713] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [564.274278] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [564.274666] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [564.275070] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [564.275598] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [564.276002] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [564.276470] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [564.276969] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [564.277456] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [564.277826] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [564.278219] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [564.278728] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [564.279151] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [564.279584] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [564.279986] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [564.280400] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [564.280814] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [564.281252] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [564.281653] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [564.282061] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [564.282437] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [564.282818] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [564.283348] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [564.283804] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [564.284215] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [564.284761] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [564.285159] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [564.285540] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [564.285987] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [564.286398] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [564.286772] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [564.287312] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [564.287691] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [564.288109] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [564.288488] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [564.288887] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [564.289446] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [564.289989] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<7> [564.291792] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [564.292801] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [564.293222] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [564.293613] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [564.295003] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [564.295455] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [564.295824] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [564.296208] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [564.296576] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<6> [564.296845] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<7> [564.296969] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [564.316163] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [564.322893] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [564.323521] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind
<6> [564.323981] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
<7> [564.324390] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [564.324797] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [564.325286] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT)
<7> [564.325697] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [564.329962] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [564.330377] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [564.330769] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [564.331237] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [564.331643] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [564.332043] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [564.332405] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [564.332769] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [564.333350] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [564.333714] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [564.334256] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [564.334708] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [564.335122] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [564.335480] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [564.335832] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [564.336213] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [564.336687] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [564.337226] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [564.338013] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [564.338442] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [564.338923] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [564.339329] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [564.339758] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [564.340187] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<3> [564.347965] atkbd serio0: Failed to enable keyboard on isa0060/serio0
<7> [564.549364] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [564.550472] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [564.551315] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [564.553022] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [564.561010] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.562860] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.564690] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.566445] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.568087] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.569988] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.571651] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.573247] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [564.574770] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [564.574785] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [564.574793] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [564.574898] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [564.575353] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [564.575723] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)
<7> [564.587695] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [564.588313] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7> [564.588710] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000
<7> [564.589211] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [564.589593] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [564.589976] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [564.590331] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [564.590675] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [564.591138] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [564.592303] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT)
<7> [564.592735] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [564.593553] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [564.593922] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [564.594299] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [564.594959] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [564.595313] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)
<7> [564.596703] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [564.597249] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [564.597728] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<7> [564.598122] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [564.598508] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [564.598889] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [564.599289] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [564.599661] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [564.600041] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [564.600412] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [564.600802] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [564.601310] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [564.601719] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [564.602100] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [564.602467] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [564.602849] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [564.603254] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [564.603623] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [564.604007] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [564.604368] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [564.604723] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [564.605136] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [564.605520] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [564.605879] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [564.606261] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [564.606619] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [564.607019] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [564.607409] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [564.607777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [564.608150] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [564.608495] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [564.608836] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [564.609247] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [564.609634] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [564.610028] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [564.610402] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [564.610858] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [564.611281] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [564.611673] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [564.612075] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [564.612431] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [564.612775] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [564.613135] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [564.613485] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [564.613853] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [564.614253] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [564.614604] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [564.614973] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [564.615321] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [564.615696] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<7> [564.616095] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [564.616461] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [564.616808] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [564.617168] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [564.617513] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [564.617874] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [564.618275] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [564.618635] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [564.619027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [564.619371] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [564.619712] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [564.620097] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [564.620464] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [564.620810] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [564.621185] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [564.621537] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [564.621873] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [564.643731] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [564.644186] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [564.644550] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [564.644908] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [564.645291] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [564.645698] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [564.646392] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [564.646725] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [564.647081] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [564.647110] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [564.649831] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0
<7> [564.650260] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [564.650615] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [564.653393] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [564.654386] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [564.656023] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [564.674295] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [564.674718] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [564.675106] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [564.675524] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [564.675983] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [564.677755] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [564.678167] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [564.678497] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [564.678806] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [564.686624] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [564.687320] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [564.690114] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [564.690969] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [564.693304] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [564.694176] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [564.694912] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [564.695237] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [564.699304] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [564.732685] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [564.740679] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input63
<7> [564.742902] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)
<6> [564.743188] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [564.744114] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [564.745024] [drm:drm_client_modeset_probe]
<7> [564.745102] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [564.745120] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [564.750010] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [564.750440] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [564.750808] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [564.751455] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [564.751853] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [564.751868] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [564.751877] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [564.751925] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [564.754023] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [564.755189] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [564.755573] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [564.756440] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [564.756861] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [564.756869] i915 device info: graphics version: 11
<7> [564.756873] i915 device info: media version: 11
<7> [564.756877] i915 device info: graphics stepping: B0
<7> [564.756880] i915 device info: media stepping: B0
<7> [564.756884] i915 device info: display stepping: B0
<7> [564.756887] i915 device info: base die stepping: **
<7> [564.756890] i915 device info: gt: 0
<7> [564.756894] i915 device info: memory-regions: 0x21
<7> [564.756897] i915 device info: page-sizes: 0x211000
<7> [564.756901] i915 device info: platform: JASPERLAKE
<7> [564.756905] i915 device info: ppgtt-size: 36
<7> [564.756908] i915 device info: ppgtt-type: 2
<7> [564.756911] i915 device info: dma_mask_size: 39
<7> [564.756915] i915 device info: is_mobile: no
<7> [564.756918] i915 device info: is_lp: no
<7> [564.756922] i915 device info: require_force_probe: no
<7> [564.756925] i915 device info: is_dgfx: no
<7> [564.756991] i915 device info: has_64bit_reloc: yes
<7> [564.756996] i915 device info: has_64k_pages: no
<7> [564.757000] i915 device info: gpu_reset_clobbers_display: no
<7> [564.757003] i915 device info: has_reset_engine: yes
<7> [564.757007] i915 device info: has_3d_pipeline: yes
<7> [564.757010] i915 device info: has_4tile: no
<7> [564.757013] i915 device info: has_flat_ccs: no
<7> [564.757017] i915 device info: has_global_mocs: no
<7> [564.757020] i915 device info: has_gmd_id: no
<7> [564.757024] i915 device info: has_gt_uc: yes
<7> [564.757027] i915 device info: has_heci_pxp: no
<7> [564.757030] i915 device info: has_heci_gscfi: no
<7> [564.757034] i915 device info: has_guc_deprivilege: no
<7> [564.757037] i915 device info: has_l3_ccs_read: no
<7> [564.757040] i915 device info: has_l3_dpf: no
<7> [564.757043] i915 device info: has_llc: yes
<7> [564.757046] i915 device info: has_logical_ring_contexts: yes
<7> [564.757050] i915 device info: has_logical_ring_elsq: yes
<7> [564.757053] i915 device info: has_media_ratio_mode: no
<7> [564.757057] i915 device info: has_mslice_steering: no
<7> [564.757060] i915 device info: has_oa_bpc_reporting: no
<7> [564.757063] i915 device info: has_oa_slice_contrib_limits: no
<7> [564.757066] i915 device info: has_oam: no
<7> [564.757070] i915 device info: has_one_eu_per_fuse_bit: no
<7> [564.757073] i915 device info: has_pxp: no
<7> [564.757076] i915 device info: has_rc6: yes
<7> [564.757080] i915 device info: has_rc6p: no
<7> [564.757083] i915 device info: has_rps: yes
<7> [564.757086] i915 device info: has_runtime_pm: yes
<7> [564.757090] i915 device info: has_snoop: no
<7> [564.757093] i915 device info: has_coherent_ggtt: no
<7> [564.757096] i915 device info: tuning_thread_rr_after_dep: no
<7> [564.757099] i915 device info: unfenced_needs_alignment: no
<7> [564.757103] i915 device info: hws_needs_physical: no
<7> [564.757106] i915 device info: has_pooled_eu: no
<7> [564.757109] i915 device info: rawclk rate: 19200 kHz
<7> [564.757114] i915 device info: display version: 11
<7> [564.757118] i915 device info: cursor_needs_physical: no
<7> [564.757121] i915 device info: has_cdclk_crawl: no
<7> [564.757125] i915 device info: has_cdclk_squash: no
<7> [564.757128] i915 device info: has_ddi: yes
<7> [564.757132] i915 device info: has_dp_mst: yes
<7> [564.757135] i915 device info: has_dsb: no
<7> [564.757138] i915 device info: has_fpga_dbg: yes
<7> [564.757142] i915 device info: has_gmch: no
<7> [564.757146] i915 device info: has_hotplug: yes
<7> [564.757149] i915 device info: has_hti: no
<7> [564.757152] i915 device info: has_ipc: yes
<7> [564.757156] i915 device info: has_overlay: no
<7> [564.757159] i915 device info: has_psr: yes
<7> [564.757162] i915 device info: has_psr_hw_tracking: yes
<7> [564.757166] i915 device info: overlay_needs_physical: no
<7> [564.757169] i915 device info: supports_tv: no
<7> [564.757173] i915 device info: has_hdcp: no
<7> [564.757176] i915 device info: has_dmc: yes
<7> [564.757179] i915 device info: has_dsc: yes
<7> [564.757183] i915 device info: iommu: enabled
<7> [564.757187] i915 device info: available engines: 40403
<7> [564.757191] i915 device info: slice total: 1, mask=0001
<7> [564.757195] i915 device info: subslice total: 4
<7> [564.757199] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [564.757203] i915 device info: EU total: 16
<7> [564.757207] i915 device info: EU per subslice: 4
<7> [564.757210] i915 device info: has slice power gating: yes
<7> [564.757214] i915 device info: has subslice power gating: yes
<7> [564.757217] i915 device info: has EU power gating: yes
<6> [564.757222] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [564.757226] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [564.757230] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [564.757541] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [564.761414] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [564.762443] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to connected
<7> [564.762763] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [564.762774] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [564.762785] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [564.763019] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [564.763034] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [564.763625] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [564.763652] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [564.763666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [564.763677] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [564.764138] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [564.764161] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [564.764172] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [564.764183] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [564.764614] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [564.764634] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [564.764643] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [564.764653] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [564.764659] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [564.764665] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [564.764733] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [564.764755] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [564.764762] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [564.764769] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [564.764775] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [564.764796] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<7> [564.764834] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<7> [564.766194] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<6> [564.783867] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [564.785804] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00180000
<6> [564.787950] fbcon: i915drmfb (fb0) is primary device
<6> [564.788653] Console: switching to colour frame buffer device 400x112
<6> [564.788678] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [564.796025] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [564.796043] [drm:drm_client_modeset_probe]
<7> [564.796103] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [564.796118] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [564.799345] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [564.799770] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [564.800568] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [564.801036] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [564.802761] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [564.802778] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [564.802787] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [564.802825] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [564.803354] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [564.805197] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [564.805606] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [564.809532] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [564.809549] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [564.809560] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [564.809572] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [564.809585] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [564.810899] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [564.810920] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [564.810954] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [564.811446] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [564.811462] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [564.811473] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [564.811895] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [564.811907] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [564.811916] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [564.811923] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [564.812074] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [564.812144] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [564.812164] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [564.812172] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [564.812179] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [564.812185] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [564.812210] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<7> [564.812928] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [564.813410] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz
<7> [564.813782] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [564.814173] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000
<7> [564.814549] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no
<7> [564.814903] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long
<7> [564.815791] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [564.816296] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]
<7> [564.818369] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [564.818775] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [564.819183] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [564.819571] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [564.819991] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288)
<7> [564.820323] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [564.820653] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [564.821415] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [564.821806] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316)
<7> [564.822244] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [564.822574] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316)
<7> [564.822900] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [564.823285] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [564.823607] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [564.823922] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816)
<7> [564.824268] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [564.824575] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816)
<7> [564.824882] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802)
<7> [564.825217] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807)
<7> [564.825531] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [564.825851] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316)
<7> [564.826206] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [564.826516] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316)
<7> [564.826922] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [564.827261] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [564.827566] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [564.827871] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816)
<7> [564.828204] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [564.828512] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816)
<7> [564.828816] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802)
<7> [564.829159] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807)
<7> [564.829486] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [564.829914] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [564.830280] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [564.830596] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b)
<7> [564.830898] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x00e001a5)
<7> [564.831236] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [564.831557] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310)
<7> [564.831864] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310)
<7> [564.832214] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [564.832529] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [564.832920] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1
<7> [564.833314] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985
<7> [564.833614] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39
<7> [564.833912] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [564.834235] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [564.834543] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0
<7> [564.834854] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0
<7> [564.835206] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1
<7> [564.835518] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446
<7> [564.835823] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446
<7> [564.836154] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446
<7> [564.836495] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz)
<7> [564.836811] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)
<7> [564.837184] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [564.837491] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [564.837797] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [564.838265] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0
<7> [564.838574] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0
<7> [564.838884] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]
<6> [564.839385] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100
<7> [564.839302] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [564.839628] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [564.840053] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [564.840363] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [564.840667] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [564.841047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [564.841355] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64
<7> [564.841662] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [564.842175] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [564.842489] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [564.842791] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [564.843277] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [564.843585] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [564.843895] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa
<7> [564.844415] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa
<7> [564.844730] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa
<7> [564.845201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310
<7> [564.845521] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0
<7> [564.845845] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [564.846378] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<6> [564.846847] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [564.846716] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [564.847245] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [564.847571] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [564.847884] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [564.848443] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [564.848759] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [564.849251] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [564.849555] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [564.849849] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [564.850334] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [564.850686] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [564.851168] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [564.851484] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [564.851788] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [564.852277] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [564.852728] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [564.853149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [564.853506] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
<7> [564.853854] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
<7> [564.854433] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
<7> [564.854745] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
<7> [564.855314] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no
<7> [564.855625] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no
<7> [564.855928] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no
<7> [564.856868] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1
<7> [564.858036] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]
<7> [564.858370] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]
<7> [564.858694] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]
<6> [564.859541] [IGT] i915_suspend: finished subtest basic-s2idle-without-i915, SUCCESS
<7> [564.859376] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]
<7> [564.859701] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]
<7> [564.859732] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [564.860173] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]
<7> [564.860592] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [564.861115] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [564.861444] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4
<7> [564.861956] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]
<7> [564.862284] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [564.864230] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on
<7> [564.864727] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [564.866524] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [564.866862] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [564.867393] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on
<7> [564.867751] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b
<7> [565.079035] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [565.079863] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [565.085584] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [565.085705] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [565.087254] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [565.088242] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [565.090516] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [565.091228] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [565.096505] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK
<7> [565.097313] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [565.100246] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1
<7> [565.100988] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1
<7> [565.103811] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [565.104562] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [565.105855] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [565.107670] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [565.108443] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [565.109643] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000
<7> [565.117408] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1
<7> [565.118275] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [565.125082] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]
<7> [565.126003] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]
<7> [565.128297] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0
<7> [565.129070] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [565.129827] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [565.132230] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]
<7> [565.132257] [drm:drm_client_modeset_probe]
<7> [565.132421] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<6> [565.132460] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [565.132454] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [565.133410] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [565.134257] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [565.135296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [565.135753] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [565.137788] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x810
<7> [565.140873] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<6> [565.141523] [IGT] i915_suspend: exiting, ret=0
<7> [565.141686] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [565.142438] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [565.143538] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [565.144428] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [565.144460] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [565.144481] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [565.145583] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [565.147593] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [565.148227] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [565.152542] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [565.153323] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [565.155229] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :
<7> [565.155252] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [565.155269] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [565.155287] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [565.155305] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [565.155809] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [565.155829] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [565.155844] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [565.156513] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [565.156533] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [565.156548] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [565.157120] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [565.157137] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [565.157149] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [565.157158] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [565.157167] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [565.157252] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [565.157281] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [565.157292] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [565.157301] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [565.157309] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [565.157347] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
|