igt@i915_module_load@load on bat-adln-1@linus-v6.6-rc2 Test details

Detail	Value
Igt-Version	IGT-Version: 1.28-g2aaeef0cd (x86_64) (Linux: 6.6.0-rc2-linus-v6.6-rc2-gce9ecca0238b+ x86_64)
Out	Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (2.071s)
Err	Starting subtest: load Subtest load: SUCCESS (2.071s)
Dmesg	<6> [45.299348] Console: switching to colour dummy device 80x25 <6> [45.299423] [IGT] i915_module_load: executing <6> [45.388347] [IGT] i915_module_load: starting subtest load <4> [45.728906] <4> [45.728920] ******************************************************** <4> [45.728922] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [45.728924] <4> [45.728926] trace_printk() being used. Allocating extra memory. <4> [45.728928] <4> [45.728929] This means that this is a DEBUG kernel and it is <4> [45.728931] unsafe for production use. <4> [45.728933] <4> [45.728935] If you see this message and you are not debugging <4> [45.728936] the kernel, report this immediately to your vendor! <4> [45.728938] <4> [45.728940] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [45.728941] ******************************************************** <7> [45.786116] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K <7> [45.786455] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:yes huc:yes slpc:yes) <7> [45.786766] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Alder Lake PCH <7> [45.787029] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [45.787446] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [45.787702] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz <7> [45.788325] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vcs2 fused off <7> [45.788543] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001 <7> [45.788737] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001 <7> [45.789457] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [45.789686] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [45.789880] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M <6> [45.790071] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [45.796342] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [45.797075] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [45.797104] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x0000000050200087 <7> [45.797392] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K <7> [45.798007] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x44a70018 <7> [45.798325] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0 <7> [45.798609] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [45.798880] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [45.799130] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [45.799405] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (RVDA) <7> [45.799707] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [45.799949] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [45.800151] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2401 tRP=24 tRDPRE=20 tRAS=52 tRCD=24 tRC=76 <7> [45.800478] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=4001 tRP=36 tRDPRE=24 tRAS=84 tRCD=36 tRC=120 <7> [45.800758] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=4401 tRP=40 tRDPRE=28 tRAS=96 tRCD=40 tRC=136 <7> [45.801044] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 3: DCLK=4801 tRP=44 tRDPRE=28 tRAS=104 tRCD=44 tRC=148 <7> [45.801306] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 0: CLK=32 <7> [45.801602] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 1: CLK=38 <7> [45.801863] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 2: CLK=48 <7> [45.802112] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 0: num_planes=0 deratedbw=8478 peakbw: 19208 <7> [45.802360] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 1: num_planes=0 deratedbw=11380 peakbw: 32008 <7> [45.802643] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 2: num_planes=0 deratedbw=11556 peakbw: 35208 <7> [45.802898] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 3: num_planes=0 deratedbw=11991 peakbw: 38408 <7> [45.803201] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 0: num_planes=0 bw=34133 <7> [45.803468] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 1: num_planes=0 bw=40533 <7> [45.803738] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 2: num_planes=0 bw=51200 <7> [45.803988] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 0: num_planes=4 deratedbw=10928 peakbw: 19208 <7> [45.804229] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 1: num_planes=4 deratedbw=15758 peakbw: 32008 <7> [45.804487] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 2: num_planes=4 deratedbw=16388 peakbw: 35208 <7> [45.804738] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 3: num_planes=4 deratedbw=17250 peakbw: 38408 <7> [45.804978] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 0: num_planes=4 bw=34133 <7> [45.805212] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 1: num_planes=4 bw=40533 <7> [45.805460] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 2: num_planes=4 bw=51200 <7> [45.805702] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 0: num_planes=0 deratedbw=12772 peakbw: 19208 <7> [45.805944] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 1: num_planes=0 deratedbw=19510 peakbw: 32008 <7> [45.806177] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 2: num_planes=0 deratedbw=20720 peakbw: 35208 <7> [45.806412] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 3: num_planes=0 deratedbw=22096 peakbw: 38408 <7> [45.806664] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 0: num_planes=0 bw=34133 <7> [45.806911] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 1: num_planes=0 bw=40533 <7> [45.807149] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 2: num_planes=0 bw=51200 <7> [45.807379] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 0: num_planes=0 deratedbw=13950 peakbw: 19208 <7> [45.807623] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 1: num_planes=0 deratedbw=22146 peakbw: 32008 <7> [45.807871] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 2: num_planes=0 deratedbw=23044 peakbw: 35208 <7> [45.808107] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 3: num_planes=0 deratedbw=23044 peakbw: 38408 <7> [45.808336] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 0: num_planes=0 bw=34133 <7> [45.808577] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 1: num_planes=0 bw=40533 <7> [45.808815] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 2: num_planes=0 bw=51200 <7> [45.809048] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 0: num_planes=0 deratedbw=14624 peakbw: 19208 <7> [45.809275] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 1: num_planes=0 deratedbw=23044 peakbw: 32008 <7> [45.809515] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 2: num_planes=0 deratedbw=23044 peakbw: 35208 <7> [45.809751] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 3: num_planes=0 deratedbw=23044 peakbw: 38408 <7> [45.809983] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 0: num_planes=0 bw=34133 <7> [45.810210] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 1: num_planes=0 bw=40533 <7> [45.810445] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 2: num_planes=0 bw=51200 <7> [45.810686] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 0: num_planes=0 deratedbw=14986 peakbw: 19208 <7> [45.810917] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 1: num_planes=0 deratedbw=23044 peakbw: 32008 <7> [45.811143] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 2: num_planes=0 deratedbw=23044 peakbw: 35208 <7> [45.811368] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 3: num_planes=0 deratedbw=23044 peakbw: 38408 <7> [45.811608] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 0: num_planes=0 bw=34133 <7> [45.811842] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 1: num_planes=0 bw=40533 <7> [45.812067] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 2: num_planes=0 bw=51200 <7> [45.813248] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [45.813534] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT ALDERLAKE-P ", BDB version 249 <7> [45.813778] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 6, min size 7) <7> [45.814018] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 395, min size 5) <7> [45.814253] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 100, min size 100) <7> [45.814502] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [45.814747] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 812, min size 812) <7> [45.814988] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 34, min size 34) <7> [45.815218] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Generating LFP data table pointers <7> [45.815472] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [45.815717] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1366, min size 1366) <7> [45.815965] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 305, min size 305) <7> [45.816210] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 78, min size 78) <7> [45.816470] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822) <7> [45.816720] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 56 (size 210, min size 210) <7> [45.816966] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7> [45.817202] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [45.817450] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806 <7> [45.817702] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [45.817947] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [45.818189] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [45.818439] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [45.818684] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [45.818926] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [45.819160] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [45.819393] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0 <7> [45.819646] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7> [45.819892] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 0 <7> [45.820124] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7> [45.820355] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0 <7> [45.820606] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 4000000a <7> [45.820901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [45.821216] i915 0000:00:02.0: [drm:check_phy_reg [i915]] Combo PHY A reg 001628a0 state mismatch: current 90035b7c mask e0000000 expected a0000000 <7> [45.821481] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [45.821794] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [45.822055] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [45.822374] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [45.822690] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [45.822963] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf <7> [45.823343] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [45.823622] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [45.823881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [45.824169] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [45.824438] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [45.824711] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [45.824969] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [45.825206] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [45.825503] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [45.825549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A <7> [45.825853] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B <7> [45.826104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C <7> [45.826350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D <7> [45.826734] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/adlp_dmc.bin <7> [45.828158] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [45.829112] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 35 us <7> [45.829397] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 3 (3.0 usec) <7> [45.829714] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 54 (54.0 usec) <7> [45.829981] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 83 (83.0 usec) <7> [45.830242] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 102 (102.0 usec) <7> [45.830517] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 147 (147.0 usec) <7> [45.830768] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 147 (147.0 usec) <6> [45.833676] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adlp_dmc.bin (v2.20) <7> [45.836384] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [45.839488] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [45.840056] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <6> [45.840368] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <7> [45.840629] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 652800 kHz <7> [45.840920] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1305600 kHz <7> [45.841241] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:184:DDI A/PHY A] Using AUX CH A (VBT) <7> [45.841566] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:184:DDI A/PHY A] <7> [45.841936] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [45.842230] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [45.842533] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless <7> [45.842828] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [45.843109] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [45.843419] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002 <7> [45.843720] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [45.844006] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [45.844279] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7> [45.844649] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:184:DDI A/PHY A] initial power sequencer: PPS 0 <7> [45.844997] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000 <7> [45.845250] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [45.845544] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [45.845791] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [45.846059] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [45.846417] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [45.846883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [45.847356] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on <7> [45.847702] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [45.849478] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 00 44 41 00 00 01 c0 02 00 02 00 00 0b 80 <7> [45.850270] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000 <7> [45.850790] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 04 92 a5 <7> [45.851604] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 3 <7> [45.852842] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] PSR2 supported <7> [45.854873] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [45.855149] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] FEC CAPABILITY: 0 <7> [45.866220] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [45.866243] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [45.866250] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [45.866256] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [45.866366] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using preferred EDID fixed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [45.866681] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using alternate EDID fixed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [45.867455] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms) <7> [45.868229] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Detected Intel HDR backlight interface version 1 <7> [45.868529] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Using Intel proprietary eDP backlight controls <7> [45.868800] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:185:eDP-1] DRRS type: seamless <7> [45.869131] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] SDR backlight is controlled through PWM <7> [45.869452] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using native PCH PWM for backlight control (controller=0) <7> [45.869725] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using AUX HDR interface for backlight control (range 0..552) <7> [45.870651] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:185:eDP-1] backlight initialized, enabled, brightness 552/552 <7> [45.871013] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000 <7> [45.871256] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [45.871510] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [45.871751] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [45.871985] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [45.872330] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [45.872932] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:193:DDI B/PHY B] <7> [45.873170] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:193:DDI B/PHY B] Using DDC pin 0x2 (VBT) <7> [45.873683] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:202:DDI TC1/PHY TC1] Using AUX CH D (VBT) <7> [45.874238] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port D/TC#1: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected) <7> [45.874611] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:202:DDI TC1/PHY TC1] <7> [45.875168] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:211:DDI TC2/PHY TC2] Using AUX CH E (VBT) <7> [45.875486] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port E/TC#2: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected) <7> [45.875818] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:211:DDI TC2/PHY TC2] <7> [45.876741] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled <7> [45.877144] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:131:pipe B] hw state readout: disabled <7> [45.877549] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:182:pipe C] hw state readout: disabled <7> [45.877817] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: enabled, pipe A <7> [45.878073] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A <7> [45.878327] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A <7> [45.878611] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A <7> [45.878877] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A <7> [45.879134] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] hw state readout: disabled, pipe A <7> [45.879384] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] hw state readout: disabled, pipe B <7> [45.879689] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] hw state readout: disabled, pipe B <7> [45.879947] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] hw state readout: disabled, pipe B <7> [45.880198] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] hw state readout: disabled, pipe B <7> [45.880461] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] hw state readout: disabled, pipe B <7> [45.880715] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] hw state readout: disabled, pipe B <7> [45.880966] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] hw state readout: disabled, pipe C <7> [45.881213] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] hw state readout: disabled, pipe C <7> [45.881474] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] hw state readout: disabled, pipe C <7> [45.881728] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] hw state readout: disabled, pipe C <7> [45.881978] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] hw state readout: disabled, pipe C <7> [45.882223] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] hw state readout: disabled, pipe C <7> [45.882547] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0 <7> [45.882812] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7> [45.883166] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:184:DDI A/PHY A] hw state readout: enabled, pipe A <7> [45.883424] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:193:DDI B/PHY B] hw state readout: disabled, pipe A <7> [45.883751] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port D/TC#1: sanitize mode (disconnected) <7> [45.884010] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:202:DDI TC1/PHY TC1] hw state readout: disabled, pipe A <7> [45.884249] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:204:DP-MST A] hw state readout: disabled, pipe A <7> [45.884499] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:205:DP-MST B] hw state readout: disabled, pipe B <7> [45.884744] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:206:DP-MST C] hw state readout: disabled, pipe C <7> [45.885002] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port E/TC#2: sanitize mode (disconnected) <7> [45.885245] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:211:DDI TC2/PHY TC2] hw state readout: disabled, pipe A <7> [45.885494] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:213:DP-MST A] hw state readout: disabled, pipe A <7> [45.885732] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:214:DP-MST B] hw state readout: disabled, pipe B <7> [45.885973] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:215:DP-MST C] hw state readout: disabled, pipe C <7> [45.886225] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0 <7> [45.886502] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1 <7> [45.886772] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [45.887040] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TBT PLL hw state readout: pipe_mask 0x0, on 0 <7> [45.887300] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [45.887576] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [45.887838] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [45.888096] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0 <7> [45.888518] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:185:eDP-1] hw state readout: enabled <7> [45.888797] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:194:HDMI-A-1] hw state readout: disabled <7> [45.889060] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:203:DP-1] hw state readout: disabled <7> [45.889312] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:212:DP-2] hw state readout: disabled <7> [45.889731] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 269300 kHz <7> [45.889975] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz <7> [45.890212] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz <7> [45.890494] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz <7> [45.890730] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz <7> [45.890964] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] min_cdclk 0 kHz <7> [45.891196] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 2154400 num active planes 1 <7> [45.891489] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] min_cdclk 0 kHz <7> [45.891733] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] min_cdclk 0 kHz <7> [45.891968] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] min_cdclk 0 kHz <7> [45.892201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] min_cdclk 0 kHz <7> [45.892444] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] min_cdclk 0 kHz <7> [45.892677] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] min_cdclk 0 kHz <7> [45.892907] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [45.893187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] min_cdclk 0 kHz <7> [45.893424] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] min_cdclk 0 kHz <7> [45.893667] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] min_cdclk 0 kHz <7> [45.893904] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] min_cdclk 0 kHz <7> [45.894134] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] min_cdclk 0 kHz <7> [45.894361] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] min_cdclk 0 kHz <7> [45.894604] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [45.894910] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [45.895396] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [setup_hw_state] <7> [45.895720] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [45.896000] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7> [45.896275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [45.896552] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [45.896821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [45.897091] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [45.897351] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 653660, link_n: 524288, tu: 64 <7> [45.897629] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [45.897907] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [45.898182] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [45.898465] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0 <7> [45.898738] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [45.898995] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [45.899256] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [45.899543] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [45.899814] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [45.900075] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 432000, pipe src: 3840x2160+0+0, pixel rate 538600 <7> [45.900345] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0 <7> [45.900636] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [45.900909] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [45.901173] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [45.901496] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c2, cfgcr1: 0x84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [45.901773] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0 <7> [45.902040] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [45.902308] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [45.902600] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [45.902871] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [45.903137] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [45.903406] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [45.903694] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [45.903962] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [45.904223] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [45.904509] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [45.904787] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [45.905051] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:131:pipe B] enable: no [setup_hw_state] <7> [45.905311] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:182:pipe C] enable: no [setup_hw_state] <7> [45.905713] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:80:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no <7> [45.905988] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:131:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [45.906246] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:182:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [45.906882] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] pipe A/plane 1A with fb: size=3840x2160@32, offset=0, pitch 15360, size 0x1fa4000 <7> [45.907147] i915 0000:00:02.0: [drm:intel_plane_disable_noatomic [i915]] Disabling [PLANE:31:plane 1A] on [CRTC:80:pipe A] <7> [45.926810] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [592K, 1420K) <7> [45.927128] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [45.927369] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000] <7> [45.927626] MCR Steering: Default steering: group=0x0, instance=0x0 <7> [45.927644] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 GT workarounds on global <7> [45.929270] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0 <7> [45.929570] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0 <7> [45.929833] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 context workarounds on rcs'0 <7> [45.931771] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0 <7> [45.932049] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0 <7> [45.932306] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on bcs'0 <7> [45.933203] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0 <7> [45.933484] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'0 <7> [45.934179] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0 <7> [45.934455] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0 <7> [45.936087] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3) <7> [45.936469] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 4 ext-regs. <7> [45.936810] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset <7> [45.971725] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0x16304f <7> [45.972058] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x44000 <7> [45.972341] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4 <7> [45.972639] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3 <7> [45.972927] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0xac8 <7> [45.973207] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x46d00000 <7> [45.973516] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0 <7> [45.973797] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0 <7> [45.974070] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0 <7> [45.974344] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0 <7> [45.974628] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0 <7> [45.974899] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0 <7> [45.975167] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0 <7> [45.975452] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0 <7> [45.975725] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no <6> [45.977348] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/tgl_guc_70.bin version 70.5.1 <6> [45.977355] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3 <7> [45.981027] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 1ms, freq = 750MHz, before = 750MHz, status = 0x8002F0EC, count = 0, ret = 0 <7> [45.982340] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <6> [45.984159] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads <6> [45.985856] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled <6> [45.985863] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled <6> [45.986631] i915 0000:00:02.0: [drm] GT0: GUC: RC enabled <7> [45.996105] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [45.996738] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [45.997146] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz <7> [45.997512] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30 <7> [45.997952] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000 <7> [45.998579] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no <7> [45.999065] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [45.999509] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A] <7> [45.999964] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048) <7> [46.000515] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5) <7> [46.001001] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30) <7> [46.001378] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 432000, found 540000) <7> [46.001808] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [46.002230] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:80:pipe A] releasing DPLL 0 <7> [46.002663] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7> [46.003060] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7> [46.003542] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [46.003996] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [46.004474] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [46.004891] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz <7> [46.005241] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30 <7> [46.005639] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000 <7> [46.005995] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no <7> [46.006331] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [46.006741] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A] <7> [46.007097] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048) <7> [46.007493] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5) <7> [46.007884] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30) <7> [46.008264] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 432000, found 540000) <7> [46.008699] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [46.009070] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:80:pipe A] releasing DPLL 0 <7> [46.009507] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7> [46.009877] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7> [46.010325] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2048) -> ( 0 - 0), size 2048 -> 0 <7> [46.010709] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69 <7> [46.011066] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm,swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [46.011405] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 6, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.011783] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 32, 32, 7, 7, 7, 7, 0, 0, 7, 187, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.012132] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.012457] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [46.012799] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.013144] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.013477] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.013813] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [46.014156] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.014516] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.014847] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.015186] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [46.015550] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.015897] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.016209] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.016522] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [46.016852] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.017193] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.017542] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.017868] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [46.018206] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.018567] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.018904] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [46.019276] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0 <7> [46.019678] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0 <6> [46.020040] i915 0000:00:02.0: [drm] Selective fetch area calculation failed in pipe A <7> [46.020047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset] <7> [46.020408] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [46.020817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [46.021201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [46.021591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [46.021950] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [46.022319] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [46.022699] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64 <7> [46.023049] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [46.023415] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [46.023789] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [46.024137] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0 <7> [46.024143] i915 0000:00:02.0: pixelformat: RGB <7> [46.024147] i915 0000:00:02.0: colorimetry: sRGB <7> [46.024151] i915 0000:00:02.0: bpc: 0 <7> [46.024155] i915 0000:00:02.0: dynamic range: VESA range <7> [46.024159] i915 0000:00:02.0: content type: Not defined <7> [46.024163] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0 <7> [46.024546] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [46.024892] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [46.025238] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [46.026088] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [46.026457] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [46.026817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600 <7> [46.027156] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0 <7> [46.027517] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [46.027856] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [46.028180] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [46.028520] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [46.028870] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [46.029204] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [46.029565] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [46.029895] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [46.030214] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [46.030610] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [46.030933] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [46.031259] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [46.031675] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [46.032003] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [46.032326] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [46.032660] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [46.032982] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [46.033301] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [46.033633] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [46.033950] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [46.034258] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [46.034585] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [46.036065] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [46.239534] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 0 <7> [46.241394] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [46.249386] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power off <7> [46.249802] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power off time <7> [46.250156] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [46.304345] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [46.305205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [46.306727] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A] <7> [46.307678] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [46.308336] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [46.309042] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A] <7> [46.309648] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B] <7> [46.310029] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1] <7> [46.310272] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A] <7> [46.310527] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B] <7> [46.310767] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C] <7> [46.310999] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2] <7> [46.311234] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A] <7> [46.311484] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B] <7> [46.311720] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C] <7> [46.311949] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [46.312207] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [46.312479] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL <7> [46.312731] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1 <7> [46.312974] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2 <7> [46.313217] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3 <7> [46.313479] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4 <7> [46.313745] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf <7> [46.314083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [46.314331] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A] <7> [46.314588] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [46.314977] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power on <7> [46.315243] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [46.927989] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [46.928831] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [46.929619] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power on <7> [46.930342] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [47.142763] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [47.143696] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [47.144985] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on <7> [47.145866] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [47.149089] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80 <7> [47.149173] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Reloading eDP link rates <7> [47.150631] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06 <7> [47.152182] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [47.152835] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [47.154485] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Clock recovery OK <7> [47.154919] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [47.157089] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [47.157615] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4 <7> [47.158606] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [47.159468] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [47.159901] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [47.160320] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms) <7> [47.161947] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000 <7> [47.176112] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf <7> [47.177475] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1] <7> [47.178305] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [47.180154] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0 <7> [47.180709] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp <7> [47.181225] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [47.182189] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [PLANE:31:plane 1A] no fb, skipping <7> [47.182631] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:131:pipe B] not active, skipping <7> [47.183029] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:182:pipe C] not active, skipping <7> [47.183399] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [47.183834] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [47.185255] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [47.185633] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [47.185956] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [47.186264] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [47.198455] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:185:eDP-1] backlight device intel_backlight registered <7> [47.199074] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7> [47.201385] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:185:eDP-1] generating connector hotplug event <7> [47.202284] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:194:HDMI-A-1] generating connector hotplug event <7> [47.203086] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1 <7> [47.204834] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:203:DP-1] generating connector hotplug event <7> [47.205791] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2 <7> [47.207281] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:212:DP-2] generating connector hotplug event <6> [47.207389] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [47.210833] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <6> [47.231229] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [47.239238] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3 <7> [47.242802] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010) <7> [47.243182] i915 0000:00:02.0: [drm:intel_audio_init [i915]] aud_ts_cdclk set to M=60, N=768 <7> [47.244332] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_D <7> [47.244821] [drm:drm_client_modeset_probe] <7> [47.245152] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] <7> [47.245184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1] <7> [47.245290] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [47.245607] i915 device info: pciid=0x46d0 rev=0x00 platform=ALDERLAKE_P (subplatform=0x2) gen=12 <7> [47.245612] i915 device info: graphics version: 12 <7> [47.245615] i915 device info: media version: 12 <7> [47.245618] i915 device info: graphics stepping: A0 <7> [47.245621] i915 device info: media stepping: A0 <7> [47.245623] i915 device info: display stepping: D0 <7> [47.245625] i915 device info: base die stepping: ** <7> [47.245627] i915 device info: gt: 0 <7> [47.245630] i915 device info: memory-regions: 0x21 <7> [47.245632] i915 device info: page-sizes: 0x211000 <7> [47.245635] i915 device info: platform: ALDERLAKE_P <7> [47.245638] i915 device info: ppgtt-size: 48 <7> [47.245640] i915 device info: ppgtt-type: 2 <7> [47.245642] i915 device info: dma_mask_size: 39 <7> [47.245645] i915 device info: is_mobile: no <7> [47.245647] i915 device info: is_lp: no <7> [47.245650] i915 device info: require_force_probe: no <7> [47.245652] i915 device info: is_dgfx: no <7> [47.245654] i915 device info: has_64bit_reloc: yes <7> [47.245657] i915 device info: has_64k_pages: no <7> [47.245659] i915 device info: gpu_reset_clobbers_display: no <7> [47.245662] i915 device info: has_reset_engine: yes <7> [47.245664] i915 device info: has_3d_pipeline: yes <7> [47.245666] i915 device info: has_4tile: no <7> [47.245669] i915 device info: has_flat_ccs: no <7> [47.245671] i915 device info: has_global_mocs: yes <7> [47.245673] i915 device info: has_gmd_id: no <7> [47.245676] i915 device info: has_gt_uc: yes <7> [47.245678] i915 device info: has_heci_pxp: no <7> [47.245680] i915 device info: has_heci_gscfi: no <7> [47.245683] i915 device info: has_guc_deprivilege: no <7> [47.245685] i915 device info: has_l3_ccs_read: no <7> [47.245687] i915 device info: has_l3_dpf: no <7> [47.245689] i915 device info: has_llc: yes <7> [47.245692] i915 device info: has_logical_ring_contexts: yes <7> [47.245694] i915 device info: has_logical_ring_elsq: yes <7> [47.245696] i915 device info: has_media_ratio_mode: no <7> [47.245698] i915 device info: has_mslice_steering: no <7> [47.245701] i915 device info: has_oa_bpc_reporting: no <7> [47.245703] i915 device info: has_oa_slice_contrib_limits: no <7> [47.245705] i915 device info: has_oam: no <7> [47.245707] i915 device info: has_one_eu_per_fuse_bit: no <7> [47.245709] i915 device info: has_pxp: yes <7> [47.245712] i915 device info: has_rc6: yes <7> [47.245714] i915 device info: has_rc6p: no <7> [47.245716] i915 device info: has_rps: yes <7> [47.245718] i915 device info: has_runtime_pm: yes <7> [47.245720] i915 device info: has_snoop: no <7> [47.245722] i915 device info: has_coherent_ggtt: no <7> [47.245724] i915 device info: tuning_thread_rr_after_dep: no <7> [47.245727] i915 device info: unfenced_needs_alignment: no <7> [47.245729] i915 device info: hws_needs_physical: no <7> [47.245731] i915 device info: has_pooled_eu: no <7> [47.245733] i915 device info: rawclk rate: 19200 kHz <7> [47.245736] i915 device info: display version: 13 <7> [47.245738] i915 device info: cursor_needs_physical: no <7> [47.245741] i915 device info: has_cdclk_crawl: yes <7> [47.245743] i915 device info: has_cdclk_squash: no <7> [47.245745] i915 device info: has_ddi: yes <7> [47.245747] i915 device info: has_dp_mst: yes <7> [47.245749] i915 device info: has_dsb: yes <7> [47.245751] i915 device info: has_fpga_dbg: yes <7> [47.245753] i915 device info: has_gmch: no <7> [47.245756] i915 device info: has_hotplug: yes <7> [47.245758] i915 device info: has_hti: no <7> [47.245760] i915 device info: has_ipc: yes <7> [47.245762] i915 device info: has_overlay: no <7> [47.245764] i915 device info: has_psr: yes <7> [47.245766] i915 device info: has_psr_hw_tracking: no <7> [47.245768] i915 device info: overlay_needs_physical: no <7> [47.245771] i915 device info: supports_tv: no <7> [47.245773] i915 device info: has_hdcp: yes <7> [47.245775] i915 device info: has_dmc: yes <7> [47.245777] i915 device info: has_dsc: yes <7> [47.245780] i915 device info: iommu: enabled <7> [47.245782] i915 device info: available engines: 40403 <7> [47.245785] i915 device info: slice total: 1, mask=0001 <7> [47.245788] i915 device info: subslice total: 2 <7> [47.245790] i915 device info: slice0: 2 subslices, mask=00000003 <7> [47.245793] i915 device info: EU total: 32 <7> [47.245795] i915 device info: EU per subslice: 16 <7> [47.245797] i915 device info: has slice power gating: yes <7> [47.245799] i915 device info: has subslice power gating: no <7> [47.245802] i915 device info: has EU power gating: no <6> [47.245804] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [47.245807] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [47.245810] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [47.248340] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [47.248655] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [47.249596] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [47.249841] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [47.250065] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [47.250286] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000 <7> [47.250632] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [47.250645] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [47.250651] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [47.250657] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [47.250701] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no <7> [47.250921] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [47.251851] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [47.252062] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [47.252856] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_B <7> [47.253232] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_C <7> [47.253613] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [47.253972] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] status updated from unknown to connected <7> [47.254870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] probed modes : <7> [47.254884] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [47.254891] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [47.254897] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] <7> [47.254905] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1] <7> [47.255205] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] status updated from unknown to disconnected <7> [47.255219] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] disconnected <7> [47.255233] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] <7> [47.255239] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1] <7> [47.255664] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] status updated from unknown to disconnected <7> [47.255679] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] disconnected <7> [47.255689] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] <7> [47.255696] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2] <7> [47.255914] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] status updated from unknown to disconnected <7> [47.255926] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] disconnected <7> [47.255936] [drm:drm_client_modeset_probe] connector 185 enabled? yes <7> [47.255941] [drm:drm_client_modeset_probe] connector 194 enabled? no <7> [47.255944] [drm:drm_client_modeset_probe] connector 203 enabled? no <7> [47.255947] [drm:drm_client_modeset_probe] connector 212 enabled? no <7> [47.256046] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [47.256068] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185 <7> [47.256072] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0 <7> [47.256076] [drm:drm_client_modeset_probe] found mode 3840x2160 <7> [47.256079] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [47.256091] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0) <7> [47.256154] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7> [47.256206] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one <7> [47.263448] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3840x2160 fb: 0x00e80000 <6> [47.266136] fbcon: i915drmfb (fb0) is primary device <7> [47.267450] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [47.267721] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz <7> [47.267906] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30 <7> [47.268085] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000 <7> [47.268268] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no <7> [47.270488] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [47.270735] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A] <7> [47.270978] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027 <7> [47.271160] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,*stwm <7> [47.271338] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 <7> [47.271543] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 <7> [47.271725] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 <7> [47.271900] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 2154400 num active planes 1 <7> [47.272224] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263 <7> [47.272422] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263 <7> [47.272892] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263 <7> [47.273080] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263 <7> [47.273264] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263 <7> [47.276001] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263 <7> [47.276233] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263 <7> [47.276492] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (42079 kHz) > old min cdclk (0 kHz) <7> [47.276703] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [fastset] <7> [47.276892] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [47.277079] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [47.277265] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [47.277688] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [47.277877] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [47.278064] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [47.278259] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64 <7> [47.278611] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [47.278793] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [47.278969] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [47.279149] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0 <7> [47.279151] i915 0000:00:02.0: pixelformat: RGB <7> [47.279153] i915 0000:00:02.0: colorimetry: sRGB <7> [47.279155] i915 0000:00:02.0: bpc: 0 <7> [47.279157] i915 0000:00:02.0: dynamic range: VESA range <7> [47.279159] i915 0000:00:02.0: content type: Not defined <7> [47.279161] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0 <7> [47.279340] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [47.279617] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [47.279798] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [47.279985] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [47.280176] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [47.280362] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600 <7> [47.280660] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0 <7> [47.280847] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [47.281031] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [47.281203] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [47.281377] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [47.281813] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [47.282000] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [47.282174] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [47.282346] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [47.282608] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [47.282788] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [47.282961] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [47.283136] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [47.283308] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [47.283587] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [47.283770] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [47.283944] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [47.284120] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:186] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [47.284298] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [47.284591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0 <7> [47.284774] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [47.284946] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [47.285114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [47.285286] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [47.285572] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [47.286294] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A] <7> [47.286590] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B] <7> [47.286777] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1] <7> [47.286956] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A] <7> [47.287137] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B] <7> [47.287316] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C] <7> [47.287608] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2] <7> [47.287794] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A] <7> [47.287972] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B] <7> [47.288145] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C] <7> [47.288314] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [47.288628] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [47.288819] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL <7> [47.289004] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1 <7> [47.289192] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2 <7> [47.289384] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3 <7> [47.289581] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4 <7> [47.293516] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2 <7> [47.295085] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1] <7> [47.295326] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [47.295844] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0 <7> [47.296059] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [47.296641] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=552/552 <6> [47.296788] Console: switching to colour frame buffer device 480x135 <7> [47.296989] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:185:eDP-1] set backlight level = 552 <7> [47.297173] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000 <6> [47.317439] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device <7> [47.336593] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [47.336606] [drm:drm_client_modeset_probe] <7> [47.336791] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] <7> [47.336811] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1] <7> [47.338879] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [47.339141] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [47.339920] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [47.340165] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [47.340398] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [47.340673] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000 <7> [47.341139] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [47.341155] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [47.341163] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [47.341171] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [47.341214] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no <7> [47.341484] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [47.342572] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [47.342845] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [47.344493] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] probed modes : <7> [47.344517] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [47.344530] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [47.344543] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] <7> [47.344557] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1] <7> [47.345047] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] disconnected <7> [47.345064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] <7> [47.345077] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1] <7> [47.345837] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] disconnected <7> [47.345854] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] <7> [47.345867] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2] <7> [47.346226] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] disconnected <7> [47.346238] [drm:drm_client_modeset_probe] connector 185 enabled? yes <7> [47.346248] [drm:drm_client_modeset_probe] connector 194 enabled? no <7> [47.346254] [drm:drm_client_modeset_probe] connector 203 enabled? no <7> [47.346260] [drm:drm_client_modeset_probe] connector 212 enabled? no <7> [47.346708] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [47.346754] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185 <7> [47.346762] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0 <7> [47.346769] [drm:drm_client_modeset_probe] found mode 3840x2160 <7> [47.346775] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config <7> [47.346839] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0) <7> [47.360412] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [47.360458] [drm:drm_client_modeset_probe] <7> [47.360520] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] <7> [47.360543] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1] <7> [47.361764] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [47.362082] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [47.366690] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [47.367000] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [47.367136] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [47.367267] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000 <7> [47.367419] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [47.367468] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [47.367473] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [47.367476] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [47.367497] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no <7> [47.367632] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [47.368523] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [47.368834] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [47.370039] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] probed modes : <7> [47.370067] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [47.370079] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [47.370091] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] <7> [47.370104] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1] <7> [47.370601] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] disconnected <7> [47.370616] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] <7> [47.370626] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1] <7> [47.371007] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] disconnected <7> [47.371018] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] <7> [47.371028] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2] <7> [47.371390] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] disconnected <7> [47.371400] [drm:drm_client_modeset_probe] connector 185 enabled? yes <7> [47.371407] [drm:drm_client_modeset_probe] connector 194 enabled? no <7> [47.371413] [drm:drm_client_modeset_probe] connector 203 enabled? no <7> [47.371418] [drm:drm_client_modeset_probe] connector 212 enabled? no <7> [47.371756] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [47.371779] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185 <7> [47.371786] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0 <7> [47.371791] [drm:drm_client_modeset_probe] found mode 3840x2160 <7> [47.371796] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config <7> [47.371824] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0) <6> [47.402834] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 <6> [47.403062] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <6> [47.405855] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [47.406113] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [47.406403] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [47.406468] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <7> [47.407442] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [47.426274] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [47.429726] [drm:eb_lookup_vmas [i915]] EINVAL at eb_validate_vma:508 <6> [47.453703] snd_hda_codec_realtek hdaudioC0D0: ALC711: SKU not ready 0x00000000 <6> [47.454749] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC711: line_outs=1 (0x21/0x0/0x0/0x0/0x0) type:hp <6> [47.454757] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) <6> [47.454759] snd_hda_codec_realtek hdaudioC0D0: hp_outs=0 (0x0/0x0/0x0/0x0/0x0) <6> [47.454762] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 <6> [47.454764] snd_hda_codec_realtek hdaudioC0D0: inputs: <6> [47.454766] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19 <6> [47.459561] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [47.459652] [IGT] i915_module_load: exiting, ret=0

<4> [45.728920] **********************************************************

<4> [45.728922] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [45.728926] ** trace_printk() being used. Allocating extra memory. **

<4> [45.728929] ** This means that this is a DEBUG kernel and it is **

<4> [45.728935] ** If you see this message and you are not debugging **

<4> [45.728936] ** the kernel, report this immediately to your vendor! **

<4> [45.728940] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [45.728941] **********************************************************

<7> [45.786116] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K

<7> [45.786455] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:yes huc:yes slpc:yes)

<7> [45.786766] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Alder Lake PCH

<7> [45.787029] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [45.787446] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [45.787702] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz

<7> [45.788325] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vcs2 fused off

<7> [45.788543] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001

<7> [45.788737] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001

<7> [45.789457] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [45.789686] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [45.789880] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M

<6> [45.790071] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [45.797075] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [45.797104] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x0000000050200087

<7> [45.797392] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K

<7> [45.798007] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x44a70018

<7> [45.798325] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0

<7> [45.798609] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [45.798880] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [45.799130] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [45.799405] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (RVDA)

<7> [45.799707] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [45.799949] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [45.800151] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2401 tRP=24 tRDPRE=20 tRAS=52 tRCD=24 tRC=76

<7> [45.800478] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=4001 tRP=36 tRDPRE=24 tRAS=84 tRCD=36 tRC=120

<7> [45.800758] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=4401 tRP=40 tRDPRE=28 tRAS=96 tRCD=40 tRC=136

<7> [45.801044] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 3: DCLK=4801 tRP=44 tRDPRE=28 tRAS=104 tRCD=44 tRC=148

<7> [45.801306] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 0: CLK=32

<7> [45.801602] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 1: CLK=38

<7> [45.801863] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 2: CLK=48

<7> [45.802112] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 0: num_planes=0 deratedbw=8478 peakbw: 19208

<7> [45.802360] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 1: num_planes=0 deratedbw=11380 peakbw: 32008

<7> [45.802643] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 2: num_planes=0 deratedbw=11556 peakbw: 35208

<7> [45.802898] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 3: num_planes=0 deratedbw=11991 peakbw: 38408

<7> [45.803201] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 0: num_planes=0 bw=34133

<7> [45.803468] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 1: num_planes=0 bw=40533

<7> [45.803738] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 2: num_planes=0 bw=51200

<7> [45.803988] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 0: num_planes=4 deratedbw=10928 peakbw: 19208

<7> [45.804229] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 1: num_planes=4 deratedbw=15758 peakbw: 32008

<7> [45.804487] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 2: num_planes=4 deratedbw=16388 peakbw: 35208

<7> [45.804738] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 3: num_planes=4 deratedbw=17250 peakbw: 38408

<7> [45.804978] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 0: num_planes=4 bw=34133

<7> [45.805212] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 1: num_planes=4 bw=40533

<7> [45.805460] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 2: num_planes=4 bw=51200

<7> [45.805702] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 0: num_planes=0 deratedbw=12772 peakbw: 19208

<7> [45.805944] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 1: num_planes=0 deratedbw=19510 peakbw: 32008

<7> [45.806177] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 2: num_planes=0 deratedbw=20720 peakbw: 35208

<7> [45.806412] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 3: num_planes=0 deratedbw=22096 peakbw: 38408

<7> [45.806664] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 0: num_planes=0 bw=34133

<7> [45.806911] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 1: num_planes=0 bw=40533

<7> [45.807149] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 2: num_planes=0 bw=51200

<7> [45.807379] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 0: num_planes=0 deratedbw=13950 peakbw: 19208

<7> [45.807623] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 1: num_planes=0 deratedbw=22146 peakbw: 32008

<7> [45.807871] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 2: num_planes=0 deratedbw=23044 peakbw: 35208

<7> [45.808107] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 3: num_planes=0 deratedbw=23044 peakbw: 38408

<7> [45.808336] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 0: num_planes=0 bw=34133

<7> [45.808577] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 1: num_planes=0 bw=40533

<7> [45.808815] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 2: num_planes=0 bw=51200

<7> [45.809048] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 0: num_planes=0 deratedbw=14624 peakbw: 19208

<7> [45.809275] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 1: num_planes=0 deratedbw=23044 peakbw: 32008

<7> [45.809515] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 2: num_planes=0 deratedbw=23044 peakbw: 35208

<7> [45.809751] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 3: num_planes=0 deratedbw=23044 peakbw: 38408

<7> [45.809983] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 0: num_planes=0 bw=34133

<7> [45.810210] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 1: num_planes=0 bw=40533

<7> [45.810445] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 2: num_planes=0 bw=51200

<7> [45.810686] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 0: num_planes=0 deratedbw=14986 peakbw: 19208

<7> [45.810917] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 1: num_planes=0 deratedbw=23044 peakbw: 32008

<7> [45.811143] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 2: num_planes=0 deratedbw=23044 peakbw: 35208

<7> [45.811368] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 3: num_planes=0 deratedbw=23044 peakbw: 38408

<7> [45.811608] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 0: num_planes=0 bw=34133

<7> [45.811842] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 1: num_planes=0 bw=40533

<7> [45.812067] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 2: num_planes=0 bw=51200

<7> [45.813248] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [45.813534] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT ALDERLAKE-P ", BDB version 249

<7> [45.813778] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 6, min size 7)

<7> [45.814018] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 395, min size 5)

<7> [45.814253] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 100, min size 100)

<7> [45.814502] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [45.814747] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 812, min size 812)

<7> [45.814988] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 34, min size 34)

<7> [45.815218] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Generating LFP data table pointers

<7> [45.815472] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [45.815717] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1366, min size 1366)

<7> [45.815965] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 305, min size 305)

<7> [45.816210] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 78, min size 78)

<7> [45.816470] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)

<7> [45.816720] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 56 (size 210, min size 210)

<7> [45.816966] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0

<7> [45.817202] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [45.817450] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806

<7> [45.817702] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [45.817947] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [45.818189] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [45.818439] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [45.818684] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [45.818926] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [45.819160] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [45.819393] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0

<7> [45.819646] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0

<7> [45.819892] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 0

<7> [45.820124] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0

<7> [45.820355] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0

<7> [45.820606] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 4000000a

<7> [45.820901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [45.821216] i915 0000:00:02.0: [drm:check_phy_reg [i915]] Combo PHY A reg 001628a0 state mismatch: current 90035b7c mask e0000000 expected a0000000

<7> [45.821481] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [45.821794] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [45.822055] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [45.822374] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [45.822690] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [45.822963] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf

<7> [45.823343] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [45.823622] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [45.823881] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [45.824169] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [45.824438] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [45.824711] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [45.824969] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [45.825206] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<6> [45.825503] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem

<7> [45.825549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A

<7> [45.825853] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B

<7> [45.826104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C

<7> [45.826350] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D

<7> [45.826734] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/adlp_dmc.bin

<7> [45.828158] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [45.829112] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 35 us

<7> [45.829397] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 3 (3.0 usec)

<7> [45.829714] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 54 (54.0 usec)

<7> [45.829981] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 83 (83.0 usec)

<7> [45.830242] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 102 (102.0 usec)

<7> [45.830517] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 147 (147.0 usec)

<7> [45.830768] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 147 (147.0 usec)

<6> [45.833676] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adlp_dmc.bin (v2.20)

<7> [45.836384] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [45.839488] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [45.840056] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind

<6> [45.840368] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

<7> [45.840629] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 652800 kHz

<7> [45.840920] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1305600 kHz

<7> [45.841241] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:184:DDI A/PHY A] Using AUX CH A (VBT)

<7> [45.841566] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:184:DDI A/PHY A]

<7> [45.841936] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [45.842230] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [45.842533] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless

<7> [45.842828] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [45.843109] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300

<7> [45.843419] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002

<7> [45.843720] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName

<7> [45.844006] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [45.844279] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0

<7> [45.844649] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:184:DDI A/PHY A] initial power sequencer: PPS 0

<7> [45.844997] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000

<7> [45.845250] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [45.845544] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [45.845791] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [45.846059] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [45.846417] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [45.846883] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [45.847356] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on

<7> [45.847702] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f

<7> [45.849478] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 00 44 41 00 00 01 c0 02 00 02 00 00 0b 80

<7> [45.850270] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000

<7> [45.850790] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 04 92 a5

<7> [45.851604] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 3

<7> [45.852842] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] PSR2 supported

<7> [45.854873] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [45.855149] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] FEC CAPABILITY: 0

<7> [45.866220] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [45.866243] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [45.866250] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [45.866256] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [45.866366] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using preferred EDID fixed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [45.866681] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using alternate EDID fixed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [45.867455] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms)

<7> [45.868229] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Detected Intel HDR backlight interface version 1

<7> [45.868529] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Using Intel proprietary eDP backlight controls

<7> [45.868800] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:185:eDP-1] DRRS type: seamless

<7> [45.869131] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] SDR backlight is controlled through PWM

<7> [45.869452] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using native PCH PWM for backlight control (controller=0)

<7> [45.869725] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using AUX HDR interface for backlight control (range 0..552)

<7> [45.870651] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:185:eDP-1] backlight initialized, enabled, brightness 552/552

<7> [45.871013] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000

<7> [45.871256] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [45.871510] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [45.871751] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [45.871985] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [45.872330] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [45.872932] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:193:DDI B/PHY B]

<7> [45.873170] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:193:DDI B/PHY B] Using DDC pin 0x2 (VBT)

<7> [45.873683] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:202:DDI TC1/PHY TC1] Using AUX CH D (VBT)

<7> [45.874238] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port D/TC#1: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)

<7> [45.874611] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:202:DDI TC1/PHY TC1]

<7> [45.875168] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:211:DDI TC2/PHY TC2] Using AUX CH E (VBT)

<7> [45.875486] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port E/TC#2: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)

<7> [45.875818] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:211:DDI TC2/PHY TC2]

<7> [45.876741] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled

<7> [45.877144] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:131:pipe B] hw state readout: disabled

<7> [45.877549] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:182:pipe C] hw state readout: disabled

<7> [45.877817] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: enabled, pipe A

<7> [45.878073] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A

<7> [45.878327] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A

<7> [45.878611] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A

<7> [45.878877] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A

<7> [45.879134] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] hw state readout: disabled, pipe A

<7> [45.879384] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] hw state readout: disabled, pipe B

<7> [45.879689] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] hw state readout: disabled, pipe B

<7> [45.879947] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] hw state readout: disabled, pipe B

<7> [45.880198] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] hw state readout: disabled, pipe B

<7> [45.880461] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] hw state readout: disabled, pipe B

<7> [45.880715] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] hw state readout: disabled, pipe B

<7> [45.880966] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] hw state readout: disabled, pipe C

<7> [45.881213] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] hw state readout: disabled, pipe C

<7> [45.881474] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] hw state readout: disabled, pipe C

<7> [45.881728] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] hw state readout: disabled, pipe C

<7> [45.881978] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] hw state readout: disabled, pipe C

<7> [45.882223] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] hw state readout: disabled, pipe C

<7> [45.882547] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0

<7> [45.882812] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp

<7> [45.883166] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:184:DDI A/PHY A] hw state readout: enabled, pipe A

<7> [45.883424] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:193:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [45.883751] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port D/TC#1: sanitize mode (disconnected)

<7> [45.884010] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:202:DDI TC1/PHY TC1] hw state readout: disabled, pipe A

<7> [45.884249] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:204:DP-MST A] hw state readout: disabled, pipe A

<7> [45.884499] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:205:DP-MST B] hw state readout: disabled, pipe B

<7> [45.884744] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:206:DP-MST C] hw state readout: disabled, pipe C

<7> [45.885002] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port E/TC#2: sanitize mode (disconnected)

<7> [45.885245] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:211:DDI TC2/PHY TC2] hw state readout: disabled, pipe A

<7> [45.885494] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:213:DP-MST A] hw state readout: disabled, pipe A

<7> [45.885732] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:214:DP-MST B] hw state readout: disabled, pipe B

<7> [45.885973] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:215:DP-MST C] hw state readout: disabled, pipe C

<7> [45.886225] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0

<7> [45.886502] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1

<7> [45.886772] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [45.887040] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TBT PLL hw state readout: pipe_mask 0x0, on 0

<7> [45.887300] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [45.887576] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [45.887838] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [45.888096] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0

<7> [45.888518] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:185:eDP-1] hw state readout: enabled

<7> [45.888797] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:194:HDMI-A-1] hw state readout: disabled

<7> [45.889060] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:203:DP-1] hw state readout: disabled

<7> [45.889312] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:212:DP-2] hw state readout: disabled

<7> [45.889731] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 269300 kHz

<7> [45.889975] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz

<7> [45.890212] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz

<7> [45.890494] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz

<7> [45.890730] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz

<7> [45.890964] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] min_cdclk 0 kHz

<7> [45.891196] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 2154400 num active planes 1

<7> [45.891489] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] min_cdclk 0 kHz

<7> [45.891733] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] min_cdclk 0 kHz

<7> [45.891968] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] min_cdclk 0 kHz

<7> [45.892201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] min_cdclk 0 kHz

<7> [45.892444] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] min_cdclk 0 kHz

<7> [45.892677] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] min_cdclk 0 kHz

<7> [45.892907] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [45.893187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] min_cdclk 0 kHz

<7> [45.893424] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] min_cdclk 0 kHz

<7> [45.893667] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] min_cdclk 0 kHz

<7> [45.893904] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] min_cdclk 0 kHz

<7> [45.894134] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] min_cdclk 0 kHz

<7> [45.894361] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] min_cdclk 0 kHz

<7> [45.894604] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [45.894910] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [45.895396] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [setup_hw_state]

<7> [45.895720] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [45.896000] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0

<7> [45.896275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [45.896552] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [45.896821] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [45.897091] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [45.897351] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 653660, link_n: 524288, tu: 64

<7> [45.897629] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [45.897907] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [45.898182] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [45.898465] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0

<7> [45.898738] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [45.898995] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [45.899256] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [45.899543] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [45.899814] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [45.900075] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 432000, pipe src: 3840x2160+0+0, pixel rate 538600

<7> [45.900345] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0

<7> [45.900636] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [45.900909] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [45.901173] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [45.901496] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c2, cfgcr1: 0x84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [45.901773] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0

<7> [45.902040] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [45.902308] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [45.902600] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [45.902871] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [45.903137] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [45.903406] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [45.903694] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [45.903962] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [45.904223] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [45.904509] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [45.904787] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [45.905051] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:131:pipe B] enable: no [setup_hw_state]

<7> [45.905311] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:182:pipe C] enable: no [setup_hw_state]

<7> [45.905713] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:80:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no

<7> [45.905988] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:131:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [45.906246] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:182:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [45.906882] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] pipe A/plane 1A with fb: size=3840x2160@32, offset=0, pitch 15360, size 0x1fa4000

<7> [45.907147] i915 0000:00:02.0: [drm:intel_plane_disable_noatomic [i915]] Disabling [PLANE:31:plane 1A] on [CRTC:80:pipe A]

<7> [45.926810] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [592K, 1420K)

<7> [45.927128] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [45.927369] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]

<7> [45.927626] MCR Steering: Default steering: group=0x0, instance=0x0

<7> [45.927644] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 GT workarounds on global

<7> [45.929270] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0

<7> [45.929570] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0

<7> [45.929833] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 context workarounds on rcs'0

<7> [45.931771] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0

<7> [45.932049] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0

<7> [45.932306] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on bcs'0

<7> [45.933203] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0

<7> [45.933484] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'0

<7> [45.934179] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0

<7> [45.934455] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0

<7> [45.936087] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)

<7> [45.936469] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 4 ext-regs.

<7> [45.936810] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset

<7> [45.971725] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0x16304f

<7> [45.972058] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x44000

<7> [45.972341] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4

<7> [45.972639] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3

<7> [45.972927] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0xac8

<7> [45.973207] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x46d00000

<7> [45.973516] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0

<7> [45.973797] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0

<7> [45.974070] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0

<7> [45.974344] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0

<7> [45.974628] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0

<7> [45.974899] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0

<7> [45.975167] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0

<7> [45.975452] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0

<7> [45.975725] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no

<6> [45.977348] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/tgl_guc_70.bin version 70.5.1

<6> [45.977355] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3

<7> [45.981027] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 1ms, freq = 750MHz, before = 750MHz, status = 0x8002F0EC, count = 0, ret = 0

<7> [45.982340] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<6> [45.984159] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads

<6> [45.985856] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled

<7> [45.996105] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [45.996738] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [45.997146] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz

<7> [45.997512] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30

<7> [45.997952] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000

<7> [45.998579] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no

<7> [45.999065] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [45.999509] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A]

<7> [45.999964] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048)

<7> [46.000515] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5)

<7> [46.001001] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30)

<7> [46.001378] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 432000, found 540000)

<7> [46.001808] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [46.002230] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:80:pipe A] releasing DPLL 0

<7> [46.002663] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes

<7> [46.003060] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1

<7> [46.003542] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [46.003996] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [46.004474] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [46.004891] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz

<7> [46.005241] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30

<7> [46.005639] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000

<7> [46.005995] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no

<7> [46.006331] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [46.006741] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A]

<7> [46.007097] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048)

<7> [46.007493] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5)

<7> [46.007884] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 30)

<7> [46.008264] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset requirement not met in port_clock (expected 432000, found 540000)

<7> [46.008699] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [46.009070] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:80:pipe A] releasing DPLL 0

<7> [46.009507] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes

<7> [46.009877] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1

<7> [46.010325] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2048) -> ( 0 - 0), size 2048 -> 0

<7> [46.010709] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69

<7> [46.011066] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm,*swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [46.011405] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 6, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.011783] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 32, 32, 7, 7, 7, 7, 0, 0, 7, 187, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.012132] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.012457] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [46.012799] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.013144] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.013477] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.013813] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [46.014156] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.014516] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.014847] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.015186] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [46.015550] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.015897] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.016209] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.016522] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [46.016852] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.017193] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.017542] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.017868] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [46.018206] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.018567] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.018904] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [46.019276] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0

<7> [46.019678] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0

<6> [46.020040] i915 0000:00:02.0: [drm] Selective fetch area calculation failed in pipe A

<7> [46.020047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset]

<7> [46.020408] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [46.020817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [46.021201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [46.021591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [46.021950] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [46.022319] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [46.022699] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64

<7> [46.023049] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [46.023415] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [46.023789] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [46.024137] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0

<7> [46.024163] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0

<7> [46.024546] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [46.024892] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [46.025238] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [46.026088] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [46.026457] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [46.026817] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600

<7> [46.027156] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0

<7> [46.027517] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [46.027856] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [46.028180] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [46.028520] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [46.028870] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [46.029204] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [46.029565] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [46.029895] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [46.030214] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [46.030610] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [46.030933] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [46.031259] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [46.031675] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [46.032003] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [46.032326] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [46.032660] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [46.032982] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [46.033301] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [46.033633] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [46.033950] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [46.034258] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [46.034585] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [46.036065] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [46.239534] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 0

<7> [46.241394] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [46.249386] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power off

<7> [46.249802] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [46.250156] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [46.304345] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [46.305205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [46.306727] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A]

<7> [46.307678] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [46.308336] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [46.309042] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A]

<7> [46.309648] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B]

<7> [46.310029] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1]

<7> [46.310272] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A]

<7> [46.310527] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B]

<7> [46.310767] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C]

<7> [46.310999] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2]

<7> [46.311234] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A]

<7> [46.311484] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B]

<7> [46.311720] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C]

<7> [46.311949] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [46.312207] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [46.312479] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL

<7> [46.312731] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1

<7> [46.312974] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2

<7> [46.313217] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3

<7> [46.313479] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4

<7> [46.313745] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf

<7> [46.314083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [46.314331] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A]

<7> [46.314588] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [46.314977] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power on

<7> [46.315243] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [46.927989] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [46.928831] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [46.929619] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power on

<7> [46.930342] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063

<7> [47.142763] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [47.143696] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [47.144985] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on

<7> [47.145866] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [47.149089] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80

<7> [47.149173] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Reloading eDP link rates

<7> [47.150631] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Using LINK_RATE_SET value 06

<7> [47.152182] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [47.152835] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [47.154485] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Clock recovery OK

<7> [47.154919] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [47.157089] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [47.157615] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4

<7> [47.158606] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [47.159468] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [47.159901] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [47.160320] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms)

<7> [47.161947] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000

<7> [47.176112] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf

<7> [47.177475] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1]

<7> [47.178305] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [47.180154] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0

<7> [47.180709] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp

<7> [47.181225] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [47.182189] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [PLANE:31:plane 1A] no fb, skipping

<7> [47.182631] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:131:pipe B] not active, skipping

<7> [47.183029] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:182:pipe C] not active, skipping

<7> [47.183399] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [47.185255] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [47.185633] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [47.185956] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [47.186264] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [47.198455] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:185:eDP-1] backlight device intel_backlight registered

<7> [47.199074] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1

<7> [47.201385] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:185:eDP-1] generating connector hotplug event

<7> [47.202284] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:194:HDMI-A-1] generating connector hotplug event

<7> [47.203086] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1

<7> [47.204834] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:203:DP-1] generating connector hotplug event

<7> [47.205791] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2

<7> [47.207281] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:212:DP-2] generating connector hotplug event

<6> [47.207389] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [47.210833] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected

<6> [47.231229] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [47.239238] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3

<7> [47.242802] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010)

<7> [47.243182] i915 0000:00:02.0: [drm:intel_audio_init [i915]] aud_ts_cdclk set to M=60, N=768

<7> [47.244332] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_D

<7> [47.245152] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1]

<7> [47.245184] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1]

<7> [47.245290] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [47.245607] i915 device info: pciid=0x46d0 rev=0x00 platform=ALDERLAKE_P (subplatform=0x2) gen=12

<7> [47.245790] i915 device info: slice0: 2 subslices, mask=00000003

<6> [47.245807] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [47.245810] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [47.248340] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [47.248655] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [47.249596] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [47.249841] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [47.250065] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [47.250286] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000

<7> [47.250632] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [47.250645] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [47.250651] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [47.250657] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [47.250701] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no

<7> [47.250921] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [47.251851] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [47.252062] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [47.252856] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_B

<7> [47.253232] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_C

<7> [47.253613] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [47.253972] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] status updated from unknown to connected

<7> [47.254870] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] probed modes :

<7> [47.254884] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [47.254891] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [47.254897] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1]

<7> [47.254905] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1]

<7> [47.255205] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] status updated from unknown to disconnected

<7> [47.255219] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] disconnected

<7> [47.255233] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1]

<7> [47.255239] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1]

<7> [47.255664] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] status updated from unknown to disconnected

<7> [47.255679] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] disconnected

<7> [47.255689] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2]

<7> [47.255696] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2]

<7> [47.255914] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] status updated from unknown to disconnected

<7> [47.255926] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] disconnected

<7> [47.255936] [drm:drm_client_modeset_probe] connector 185 enabled? yes

<7> [47.255941] [drm:drm_client_modeset_probe] connector 194 enabled? no

<7> [47.255944] [drm:drm_client_modeset_probe] connector 203 enabled? no

<7> [47.255947] [drm:drm_client_modeset_probe] connector 212 enabled? no

<7> [47.256046] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [47.256068] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185

<7> [47.256072] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0

<7> [47.256076] [drm:drm_client_modeset_probe] found mode 3840x2160

<7> [47.256079] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [47.256091] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0)

<7> [47.256154] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<7> [47.256206] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one

<7> [47.263448] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3840x2160 fb: 0x00e80000

<7> [47.267450] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [47.267721] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz

<7> [47.267906] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30

<7> [47.268085] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000

<7> [47.268268] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no

<7> [47.270488] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [47.270735] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A]

<7> [47.270978] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027

<7> [47.271160] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [47.271338] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0

<7> [47.271543] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201

<7> [47.271725] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207

<7> [47.271900] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 2154400 num active planes 1

<7> [47.272224] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263

<7> [47.272422] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263

<7> [47.272892] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263

<7> [47.273080] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263

<7> [47.273264] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263

<7> [47.276001] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263

<7> [47.276233] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263

<7> [47.276492] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (42079 kHz) > old min cdclk (0 kHz)

<7> [47.276703] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [fastset]

<7> [47.276892] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [47.277079] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [47.277265] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [47.277688] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [47.277877] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [47.278064] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [47.278259] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64

<7> [47.278611] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [47.278793] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [47.278969] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [47.279149] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0

<7> [47.279161] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0

<7> [47.279340] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [47.279617] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [47.279798] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [47.279985] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [47.280176] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [47.280362] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600

<7> [47.280660] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0

<7> [47.280847] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [47.281031] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [47.281203] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [47.281377] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [47.281813] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [47.282000] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [47.282174] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [47.282346] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [47.282608] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [47.282788] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [47.282961] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [47.283136] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [47.283308] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [47.283587] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [47.283770] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [47.283944] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [47.284120] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:186] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [47.284298] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [47.284591] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0

<7> [47.284774] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [47.284946] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [47.285114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [47.285286] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [47.285572] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [47.286294] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A]

<7> [47.286590] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B]

<7> [47.286777] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1]

<7> [47.286956] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A]

<7> [47.287137] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B]

<7> [47.287316] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C]

<7> [47.287608] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2]

<7> [47.287794] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A]

<7> [47.287972] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B]

<7> [47.288145] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C]

<7> [47.288314] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [47.288628] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [47.288819] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL

<7> [47.289004] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1

<7> [47.289192] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2

<7> [47.289384] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3

<7> [47.289581] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4

<7> [47.293516] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2

<7> [47.295085] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1]

<7> [47.295326] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [47.295844] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0

<7> [47.296059] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [47.296641] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=552/552

<6> [47.296788] Console: switching to colour frame buffer device 480x135

<7> [47.296989] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:185:eDP-1] set backlight level = 552

<7> [47.297173] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000

<6> [47.317439] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device

<7> [47.336593] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]

<7> [47.336791] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1]

<7> [47.336811] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1]

<7> [47.338879] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [47.339141] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [47.339920] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [47.340165] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [47.340398] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [47.340673] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000

<7> [47.341139] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [47.341155] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [47.341163] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [47.341171] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [47.341214] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no

<7> [47.341484] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [47.342572] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [47.342845] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [47.344493] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] probed modes :

<7> [47.344517] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [47.344530] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [47.344543] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1]

<7> [47.344557] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1]

<7> [47.345047] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] disconnected

<7> [47.345064] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1]

<7> [47.345077] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1]

<7> [47.345837] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] disconnected

<7> [47.345854] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2]

<7> [47.345867] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2]

<7> [47.346226] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] disconnected

<7> [47.346238] [drm:drm_client_modeset_probe] connector 185 enabled? yes

<7> [47.346248] [drm:drm_client_modeset_probe] connector 194 enabled? no

<7> [47.346254] [drm:drm_client_modeset_probe] connector 203 enabled? no

<7> [47.346260] [drm:drm_client_modeset_probe] connector 212 enabled? no

<7> [47.346708] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [47.346754] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185

<7> [47.346762] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0

<7> [47.346769] [drm:drm_client_modeset_probe] found mode 3840x2160

<7> [47.346775] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config

<7> [47.346839] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0)

<7> [47.360412] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]

<7> [47.360520] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1]

<7> [47.360543] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1]

<7> [47.361764] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [47.362082] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [47.366690] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [47.367000] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [47.367136] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [47.367267] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000

<7> [47.367419] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [47.367468] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [47.367473] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [47.367476] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [47.367497] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no

<7> [47.367632] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [47.368523] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [47.368834] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [47.370039] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:185:eDP-1] probed modes :

<7> [47.370067] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [47.370079] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [47.370091] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1]

<7> [47.370104] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1]

<7> [47.370601] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:194:HDMI-A-1] disconnected

<7> [47.370616] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1]

<7> [47.370626] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1]

<7> [47.371007] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:203:DP-1] disconnected

<7> [47.371018] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2]

<7> [47.371028] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2]

<7> [47.371390] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:212:DP-2] disconnected

<7> [47.371400] [drm:drm_client_modeset_probe] connector 185 enabled? yes

<7> [47.371407] [drm:drm_client_modeset_probe] connector 194 enabled? no

<7> [47.371413] [drm:drm_client_modeset_probe] connector 203 enabled? no

<7> [47.371418] [drm:drm_client_modeset_probe] connector 212 enabled? no

<7> [47.371756] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [47.371779] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185

<7> [47.371786] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0

<7> [47.371791] [drm:drm_client_modeset_probe] found mode 3840x2160

<7> [47.371796] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config

<7> [47.371824] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0)

<6> [47.402834] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100

<6> [47.403062] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)

<6> [47.405855] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [47.406113] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [47.406468] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010

<7> [47.407442] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [47.429726] [drm:eb_lookup_vmas [i915]] EINVAL at eb_validate_vma:508

<6> [47.453703] snd_hda_codec_realtek hdaudioC0D0: ALC711: SKU not ready 0x00000000

<6> [47.454749] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC711: line_outs=1 (0x21/0x0/0x0/0x0/0x0) type:hp

<6> [47.454757] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)

<6> [47.454759] snd_hda_codec_realtek hdaudioC0D0: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)

<6> [47.454762] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0

<6> [47.459561] [IGT] i915_module_load: finished subtest load, SUCCESS

Results for igt@i915_module_load@load