Results for igt@i915_selftest@live@gt_pm

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g605d12880 (x86_64) (Linux: 6.6.0-rc1-linus-v6.6-rc1-g0bb80ecc33a8+ x86_64)
Out 
Starting dynamic subtest: gt_pm
Dynamic subtest gt_pm: SUCCESS (2.419s)
Err 
Starting dynamic subtest: gt_pm
Dynamic subtest gt_pm: SUCCESS (2.419s)
Dmesg
<6> [147.045109] [IGT] i915_selftest: starting dynamic subtest gt_pm
<5> [147.153764] Setting dangerous option enable_guc - tainting kernel
<5> [147.153771] Setting dangerous option live_selftests - tainting kernel
<7> [147.199482] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [147.199710] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no)
<6> [147.199860] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A
<7> [147.199871] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH
<7> [147.200056] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [147.200267] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [147.200386] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [147.200934] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [147.201058] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [147.201184] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [147.201288] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [147.201292] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [147.202062] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [147.202082] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047
<7> [147.202215] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [147.202526] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018
<7> [147.202682] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [147.202814] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [147.202945] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [147.203091] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [147.207033] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [147.207189] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [147.207318] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [147.207449] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [147.207577] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [147.207675] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no
<7> [147.207774] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [147.207865] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no
<7> [147.207956] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no
<7> [147.208112] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [147.208232] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no
<7> [147.208331] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [147.208423] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [147.208514] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [147.209020] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [147.209169] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206
<7> [147.209320] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [147.209464] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [147.209608] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [147.209751] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [147.209895] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [147.210061] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [147.210205] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [147.210363] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [147.210585] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [147.210794] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [147.210951] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [147.211106] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [147.211250] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [147.211435] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [147.211647] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [147.211836] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [147.211977] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [147.212129] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4
<7> [147.212331] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [147.212541] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [147.212695] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [147.212840] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0
<7> [147.213013] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [147.213229] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [147.213461] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [147.213620] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [147.213770] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [147.214386] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [147.214532] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz
<7> [147.214749] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [147.214996] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [147.215152] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [147.215329] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [147.215554] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [147.215788] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [147.215937] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [147.216092] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [147.216234] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [147.216478] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin
<7> [147.217219] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [147.217627] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<6> [147.217699] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)
<7> [147.217764] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [147.217904] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [147.218049] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [147.218212] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [147.218344] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [147.218476] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [147.218610] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [147.218744] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [147.218875] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [147.220194] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [147.221365] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [147.221599] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B]
<7> [147.221730] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [147.222243] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C]
<7> [147.222383] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [147.222602] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] Using AUX CH A (VBT)
<7> [147.222806] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E]
<7> [147.223133] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [147.223520] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [147.223687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [147.223866] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [147.224025] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [147.224171] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [147.224312] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [147.224453] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [147.224594] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [147.224738] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [147.224881] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [147.225036] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [147.225177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [147.225321] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [147.225465] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [147.225606] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A
<7> [147.225752] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [147.225899] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [147.226060] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [147.226206] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [147.226385] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled
<7> [147.226535] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled
<7> [147.226684] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled
<7> [147.226822] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [147.226956] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [147.227103] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [147.227237] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [147.227379] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [147.227518] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [147.227675] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [147.227810] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [147.227952] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [147.228118] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [147.228258] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [147.228395] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [147.228564] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [147.228706] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [147.228847] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [147.228990] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [147.229151] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [147.229287] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [147.229425] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [147.231853] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [240K, 784K)
<7> [147.231990] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [147.232114] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]
<7> [147.232237] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [147.232376] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global
<7> [147.233364] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [147.233506] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [147.233638] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0
<7> [147.236595] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)
<7> [147.236771] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs.
<7> [147.236930] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset
<7> [147.264014] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f
<7> [147.264204] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0
<7> [147.264336] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000
<7> [147.264470] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3
<7> [147.264599] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a
<7> [147.264729] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004
<7> [147.264863] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0
<7> [147.264992] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0
<7> [147.265183] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0
<7> [147.265320] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0
<7> [147.265456] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0
<7> [147.265593] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0
<7> [147.265730] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0
<7> [147.265867] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0
<7> [147.266012] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no
<6> [147.267180] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [147.267185] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [147.273815] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [147.275264] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [147.275677] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [147.275684] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<7> [147.292373] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [147.292642] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [147.292853] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [147.293079] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [147.293387] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [147.293747] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [147.294851] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [147.295139] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [147.295382] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [147.295610] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [147.300226] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event
<7> [147.300681] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event
<7> [147.301191] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1
<7> [147.302132] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event
<6> [147.302227] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [147.304655] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected
<6> [147.320265] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [147.321248] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input56
<7> [147.322243] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [147.323031] [drm:drm_client_modeset_probe]
<7> [147.323068] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [147.322997] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [147.323076] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [147.323213] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected
<7> [147.323229] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [147.323237] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [147.323245] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [147.323254] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [147.323433] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected
<7> [147.323446] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [147.323452] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [147.323460] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [147.323467] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [147.323654] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] status updated from unknown to disconnected
<7> [147.323666] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<7> [147.323674] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [147.323679] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [147.323684] [drm:drm_client_modeset_probe] connector 105 enabled? no
<7> [147.323689] [drm:drm_client_modeset_probe] connector 109 enabled? no
<7> [147.323727] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [147.323739] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [147.323761] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [147.323771] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [147.323677] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [147.324437] [drm:drm_client_modeset_probe]
<7> [147.324465] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]
<7> [147.324412] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [147.324471] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]
<7> [147.324606] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected
<7> [147.324610] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]
<7> [147.324619] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9
<7> [147.324624] i915 device info: graphics version: 9
<7> [147.324627] i915 device info: media version: 9
<7> [147.324630] i915 device info: graphics stepping: F0
<7> [147.324633] i915 device info: media stepping: F0
<7> [147.324636] i915 device info: display stepping: C0
<7> [147.324639] i915 device info: base die stepping: **
<7> [147.324641] i915 device info: gt: 2
<7> [147.324644] i915 device info: memory-regions: 0x21
<7> [147.324647] i915 device info: page-sizes: 0x11000
<7> [147.324650] i915 device info: platform: KABYLAKE
<7> [147.324652] i915 device info: ppgtt-size: 48
<7> [147.324655] i915 device info: ppgtt-type: 2
<7> [147.324658] i915 device info: dma_mask_size: 39
<7> [147.324661] i915 device info: is_mobile: no
<7> [147.324664] i915 device info: is_lp: no
<7> [147.324667] i915 device info: require_force_probe: no
<7> [147.324669] i915 device info: is_dgfx: no
<7> [147.324672] i915 device info: has_64bit_reloc: yes
<7> [147.324675] i915 device info: has_64k_pages: no
<7> [147.324615] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]
<7> [147.324678] i915 device info: gpu_reset_clobbers_display: no
<7> [147.324681] i915 device info: has_reset_engine: yes
<7> [147.324683] i915 device info: has_3d_pipeline: yes
<7> [147.324685] i915 device info: has_4tile: no
<7> [147.324688] i915 device info: has_flat_ccs: no
<7> [147.324690] i915 device info: has_global_mocs: no
<7> [147.324692] i915 device info: has_gmd_id: no
<7> [147.324695] i915 device info: has_gt_uc: yes
<7> [147.324697] i915 device info: has_heci_pxp: no
<7> [147.324699] i915 device info: has_heci_gscfi: no
<7> [147.324702] i915 device info: has_guc_deprivilege: no
<7> [147.324704] i915 device info: has_l3_ccs_read: no
<7> [147.324706] i915 device info: has_l3_dpf: no
<7> [147.324709] i915 device info: has_llc: yes
<7> [147.324711] i915 device info: has_logical_ring_contexts: yes
<7> [147.324713] i915 device info: has_logical_ring_elsq: no
<7> [147.324716] i915 device info: has_media_ratio_mode: no
<7> [147.324718] i915 device info: has_mslice_steering: no
<7> [147.324720] i915 device info: has_oa_bpc_reporting: no
<7> [147.324723] i915 device info: has_oa_slice_contrib_limits: no
<7> [147.324725] i915 device info: has_oam: no
<7> [147.324728] i915 device info: has_one_eu_per_fuse_bit: no
<7> [147.324730] i915 device info: has_pxp: no
<7> [147.324732] i915 device info: has_rc6: yes
<7> [147.324734] i915 device info: has_rc6p: no
<7> [147.324737] i915 device info: has_rps: yes
<7> [147.324739] i915 device info: has_runtime_pm: yes
<7> [147.324741] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected
<7> [147.324745] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]
<7> [147.324754] i915 device info: has_snoop: no
<7> [147.324757] i915 device info: has_coherent_ggtt: yes
<7> [147.324760] i915 device info: tuning_thread_rr_after_dep: no
<7> [147.324763] i915 device info: unfenced_needs_alignment: no
<7> [147.324766] i915 device info: hws_needs_physical: no
<7> [147.324768] i915 device info: has_pooled_eu: no
<7> [147.324771] i915 device info: rawclk rate: 24000 kHz
<7> [147.324774] i915 device info: display version: 9
<7> [147.324777] i915 device info: cursor_needs_physical: no
<7> [147.324780] i915 device info: has_cdclk_crawl: no
<7> [147.324783] i915 device info: has_cdclk_squash: no
<7> [147.324786] i915 device info: has_ddi: yes
<7> [147.324789] i915 device info: has_dp_mst: yes
<7> [147.324792] i915 device info: has_dsb: no
<7> [147.324794] i915 device info: has_fpga_dbg: yes
<7> [147.324797] i915 device info: has_gmch: no
<7> [147.324800] i915 device info: has_hotplug: yes
<7> [147.324803] i915 device info: has_hti: no
<7> [147.324805] i915 device info: has_ipc: yes
<7> [147.324808] i915 device info: has_overlay: no
<7> [147.324811] i915 device info: has_psr: yes
<7> [147.324814] i915 device info: has_psr_hw_tracking: yes
<7> [147.324749] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]
<7> [147.324817] i915 device info: overlay_needs_physical: no
<7> [147.324819] i915 device info: supports_tv: no
<7> [147.324821] i915 device info: has_hdcp: yes
<7> [147.324823] i915 device info: has_dmc: yes
<7> [147.324826] i915 device info: has_dsc: no
<7> [147.324828] i915 device info: iommu: enabled
<7> [147.324831] i915 device info: available engines: 40403
<7> [147.324833] i915 device info: slice total: 1, mask=0001
<7> [147.324836] i915 device info: subslice total: 3
<7> [147.324839] i915 device info: slice0: 3 subslices, mask=00000007
<7> [147.324842] i915 device info: slice1: 0 subslices, mask=00000000
<7> [147.324844] i915 device info: slice2: 0 subslices, mask=00000000
<7> [147.324847] i915 device info: EU total: 24
<7> [147.324849] i915 device info: EU per subslice: 8
<7> [147.324852] i915 device info: has slice power gating: no
<7> [147.324854] i915 device info: has subslice power gating: no
<7> [147.324856] i915 device info: has EU power gating: yes
<6> [147.324859] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [147.324861] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [147.324864] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<6> [147.324868] i915: Performing live selftests with st_random_seed=0x21d898d st_timeout=500
<6> [147.324871] i915: Running gt_pm
<7> [147.324891] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected
<6> [147.324893] i915: Running intel_gt_pm_live_selftests/live_gt_clocks
<7> [147.324897] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [147.324901] [drm:drm_client_modeset_probe] connector 95 enabled? no
<7> [147.324904] [drm:drm_client_modeset_probe] connector 105 enabled? no
<7> [147.324907] [drm:drm_client_modeset_probe] connector 109 enabled? no
<7> [147.324932] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [147.324940] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [147.324953] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [147.324960] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<6> [147.330330] rcs0: TIMESTAMP 12011 cycles [1000917ns] in 1000940ns [12012 cycles], using CS clock frequency of 12000KHz
<6> [147.335373] bcs0: TIMESTAMP 12010 cycles [1000834ns] in 1000875ns [12011 cycles], using CS clock frequency of 12000KHz
<6> [147.340433] vcs0: TIMESTAMP 12010 cycles [1000834ns] in 1001007ns [12013 cycles], using CS clock frequency of 12000KHz
<6> [147.345481] vecs0: TIMESTAMP 12009 cycles [1000750ns] in 1000820ns [12010 cycles], using CS clock frequency of 12000KHz
<6> [147.346132] i915: Running intel_gt_pm_live_selftests/live_rc6_manual
<7> [147.431426] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [147.535195] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [147.536134] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [147.536945] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [147.538326] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [147.711170] GPU consumed 868184uW in RC0 and 588uW in RC6
<6> [147.711567] i915: Running intel_gt_pm_live_selftests/live_rps_clock_interval
<7> [147.712242] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [147.713156] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [147.714543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<6> [147.724846] rcs0: rps counted 750 C0 cycles [1000000ns] in 1000560ns [751 cycles], using GT clock frequency of 12000KHz
<6> [147.734152] i915: Running intel_gt_pm_live_selftests/live_rps_control
<6> [147.738476] rcs0: range:[15:350MHz, 45:1150MHz] limit:[45:1150MHz], 15:45 response 50618ns:137736ns
<6> [147.741973] bcs0: range:[15:350MHz, 45:1150MHz] limit:[45:1150MHz], 15:45 response 50646ns:137774ns
<6> [147.745115] vcs0: range:[15:350MHz, 45:1150MHz] limit:[45:1150MHz], 15:45 response 50700ns:139552ns
<6> [147.748387] vecs0: range:[15:350MHz, 45:1150MHz] limit:[45:1150MHz], 15:45 response 50642ns:137816ns
<6> [147.758302] i915: Running intel_gt_pm_live_selftests/live_rps_frequency_cs
<6> [147.804013] rcs0: min:38345KHz @ 350MHz, max:122031KHz @ 1150MHz [97%]
<6> [147.845014] bcs0: min:38314KHz @ 350MHz, max:122033KHz @ 1150MHz [97%]
<6> [147.885014] vcs0: min:38296KHz @ 350MHz, max:122032KHz @ 1150MHz [97%]
<6> [147.925014] vecs0: min:38359KHz @ 350MHz, max:122032KHz @ 1150MHz [97%]
<6> [147.937403] i915: Running intel_gt_pm_live_selftests/live_rps_frequency_srm
<6> [147.978017] rcs0: min:5300KHz @ 350MHz, max:13859KHz @ 1150MHz [80%]
<6> [148.018014] bcs0: min:6155KHz @ 350MHz, max:14741KHz @ 1150MHz [73%]
<6> [148.058012] vcs0: min:6154KHz @ 350MHz, max:14742KHz @ 1150MHz [73%]
<6> [148.098012] vecs0: min:6187KHz @ 350MHz, max:14844KHz @ 1150MHz [73%]
<6> [148.108185] i915: Running intel_gt_pm_live_selftests/live_rps_power
<6> [148.189133] rcs0: min:991mW @ 3083MHz, max:6895mW @ 10150MHz
<6> [148.270239] bcs0: min:914mW @ 3083MHz, max:5729mW @ 10150MHz
<6> [148.357239] vcs0: min:952mW @ 3083MHz, max:5777mW @ 10150MHz
<6> [148.439239] vecs0: min:1004mW @ 3083MHz, max:5789mW @ 10150MHz
<6> [148.447376] i915: Running intel_gt_pm_live_selftests/live_rps_interrupt
<6> [148.447519] i915: Running intel_gt_pm_live_selftests/live_rps_dynamic
<6> [148.447606] RPS has timer support
<6> [148.510180] rcs0: dynamically reclocked to 69:1150MHz while busy in 26935527ns, and 21:350MHz while idle in 29005672ns
<6> [148.545180] bcs0: dynamically reclocked to 69:1150MHz while busy in 15278646ns, and 21:350MHz while idle in 15018564ns
<6> [148.585763] vcs0: dynamically reclocked to 69:1150MHz while busy in 18966946ns, and 21:350MHz while idle in 20231548ns
<6> [148.626849] vecs0: dynamically reclocked to 69:1150MHz while busy in 18999801ns, and 21:350MHz while idle in 20523067ns
<6> [148.638350] i915: Running intel_gt_pm_live_selftests/live_gt_resume
<6> [148.639956] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.639988] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.646566] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.647789] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.648709] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.648725] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.653763] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.653787] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.662778] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.664072] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.665312] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.665335] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.670245] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.670270] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.677478] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.678636] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.679539] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.679560] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.684570] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.684602] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.693173] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.694397] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.695350] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.695365] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.699455] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.699477] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.708782] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.710063] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.711313] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.711335] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.716336] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.716360] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.724826] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.726073] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.726946] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.726960] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.731379] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.731404] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.738143] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 3ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.739415] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.740367] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.740381] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.744522] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.744551] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.752239] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.753426] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.754335] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.754350] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.758279] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.758301] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.765076] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 3ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.766293] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.767303] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.767318] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.771783] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.771806] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.778209] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.779376] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.780267] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.780282] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.784244] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.784266] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.792260] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.793446] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.794362] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.794376] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.797934] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.797957] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.806764] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.807951] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.808874] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.808896] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.813500] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.813530] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.820090] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.821335] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.822554] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.822576] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.826847] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.826878] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.833190] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.834379] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.835310] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.835325] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.839166] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.839189] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.845567] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.846755] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.847679] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.847693] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.851412] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.851435] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.859186] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.860368] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.861269] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.861283] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.865083] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.865107] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.871210] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.872358] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.873253] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.873268] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.877248] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.877270] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.883569] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.884750] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.885667] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.885682] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.889169] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.889191] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.897817] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.898661] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.899295] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.899306] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.903077] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.903093] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.910155] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.910967] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.911592] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.911602] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.914300] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.914315] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.922098] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.922907] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.923539] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.923548] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.927349] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.927365] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.933138] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 3ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.933945] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.934579] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.934589] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.937563] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.937578] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.942927] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.943799] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.944433] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.944447] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.947300] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.947316] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.954804] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.955650] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.956282] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.956295] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.959371] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.959386] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.967157] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.967961] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.968605] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.968616] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.971942] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.971959] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.979796] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [148.980644] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.981276] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.981286] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.983898] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.983914] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [148.989162] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8000F0EC, count = 0, ret = 0
<7> [148.989969] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [148.990614] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [148.990625] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [148.993383] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [148.993405] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.001152] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.001961] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.002628] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.002638] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.005856] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.005879] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.011951] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.012801] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.013427] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.013441] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.016818] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.016835] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.022164] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.022945] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.023566] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.023576] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.026332] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.026347] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.034181] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.034991] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.035649] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.035659] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.038473] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.038488] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.046165] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.046951] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.047559] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.047569] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.050321] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.050336] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.056142] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.056950] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.057609] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.057624] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.060789] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.060806] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.068805] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 4ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.069671] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.070287] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.070302] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.073782] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.073803] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.079882] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.080732] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.081363] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.081378] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.084731] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.084752] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.090383] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.091262] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.091824] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.091834] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.094815] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.094835] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.100152] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.100960] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.101605] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.101616] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.104450] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.104465] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.109848] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.110689] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.111331] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.111341] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.114181] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.114196] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.120142] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.120951] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.121612] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.121627] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.124991] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.125061] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.130431] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.131123] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.131735] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.131746] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<6> [149.133920] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1
<6> [149.133933] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0
<7> [149.138926] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 2ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0
<7> [149.139386] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<6> [149.139662] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled
<6> [149.139667] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled
<7> [149.140998] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [149.141477] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [149.141748] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [149.142033] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [149.142361] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [149.167416] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [149.225146] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<4> [149.288463] i915: probe of 0000:00:02.0 failed with error -25
<6> [149.464043] [IGT] i915_selftest: finished subtest gt_pm, SUCCESS
Created at 2023-09-11 01:21:38