igt@i915_module_load@load on fi-kbl-guc@linus-v6.6-rc1 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g605d12880 (x86_64) (Linux: 6.6.0-rc1-linus-v6.6-rc1-g0bb80ecc33a8+ x86_64)
Out	Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (0.869s)
Err	Starting subtest: load Subtest load: SUCCESS (0.869s)
Dmesg	<6> [34.296784] Console: switching to colour dummy device 80x25 <6> [34.296846] [IGT] i915_module_load: executing <6> [34.304114] [IGT] i915_module_load: starting subtest load <4> [34.833877] <4> [34.833885] ******************************************************** <4> [34.833887] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [34.833888] <4> [34.833890] trace_printk() being used. Allocating extra memory. <4> [34.833891] <4> [34.833893] This means that this is a DEBUG kernel and it is <4> [34.833894] unsafe for production use. <4> [34.833896] <4> [34.833897] If you see this message and you are not debugging <4> [34.833899] the kernel, report this immediately to your vendor! <4> [34.833900] <4> [34.833902] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [34.833903] ****************************************************** <5> [34.845964] Setting dangerous option enable_guc - tainting kernel <7> [34.891526] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K <7> [34.891744] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no) <6> [34.891896] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A <7> [34.891908] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH <7> [34.892085] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [34.892330] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [34.892452] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz <7> [34.893176] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [34.893287] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [34.893392] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M <6> [34.893494] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [34.895889] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [34.896660] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [34.896686] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047 <7> [34.896882] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K <7> [34.897341] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018 <7> [34.897504] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [34.897636] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [34.897767] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [34.897899] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [34.903038] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [34.903195] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [34.903336] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [34.903477] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [34.903618] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [34.903728] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [34.903833] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [34.903936] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no <7> [34.904054] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [34.904149] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [34.904241] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no <7> [34.904333] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [34.904424] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [34.904515] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [34.904982] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [34.905155] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206 <7> [34.905306] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [34.905450] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [34.905594] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [34.905742] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [34.905889] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812) <7> [34.906045] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34) <7> [34.906194] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [34.906342] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [34.906489] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [34.906636] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78) <7> [34.906774] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [34.906916] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [34.907064] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [34.907212] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [34.907357] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [34.907504] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [34.907646] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [34.907789] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4 <7> [34.907930] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [34.908079] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8 <7> [34.908218] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [34.908356] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0 <7> [34.908496] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [34.908650] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [34.908830] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [34.908988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [34.909151] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [34.909610] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [34.909753] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [34.909912] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [34.910115] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [34.910259] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [34.910398] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [34.910549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [34.910703] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [34.910748] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [34.910890] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [34.911043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [34.911187] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [34.911399] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin <7> [34.912854] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [34.913415] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [34.913618] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [34.913818] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [34.914024] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [34.914219] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [34.914424] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [34.914617] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [34.914811] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [34.915057] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [34.915210] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [34.917008] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [34.918611] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [34.918952] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <6> [34.919130] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <7> [34.919274] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B] <7> [34.919405] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT) <7> [34.919835] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C] <7> [34.919964] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [34.920198] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] Using AUX CH A (VBT) <6> [34.920370] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) <7> [34.920343] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E] <7> [34.920590] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [34.920920] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [34.921121] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [34.921283] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [34.921425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [34.921566] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A <7> [34.921710] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [34.921853] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B <7> [34.922006] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B <7> [34.922151] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [34.922292] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C <7> [34.922437] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C <7> [34.922580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [34.922725] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A <7> [34.922868] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A <7> [34.923023] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A <7> [34.923166] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [34.923316] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [34.923465] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [34.923613] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [34.923825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled <7> [34.923981] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled <7> [34.924154] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled <7> [34.924291] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [34.924425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz <7> [34.924560] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [34.924693] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [34.924838] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz <7> [34.924978] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz <7> [34.925125] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [34.925264] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [34.925410] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz <7> [34.925547] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz <7> [34.925684] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [34.925820] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [34.926018] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [34.926165] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [34.926310] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [34.926453] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [34.926596] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [34.926734] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [34.926870] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [34.932172] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [240K, 784K) <7> [34.932312] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [34.932425] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000] <7> [34.932545] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [34.932679] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global <7> [34.933701] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0 <7> [34.933844] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0 <7> [34.933978] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0 <7> [34.936453] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3) <7> [34.936629] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs. <7> [34.936791] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset <7> [34.963353] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f <7> [34.963528] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0 <7> [34.963667] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000 <7> [34.963800] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3 <7> [34.963933] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a <7> [34.964081] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004 <7> [34.964234] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0 <7> [34.964368] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0 <7> [34.964501] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0 <7> [34.964634] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0 <7> [34.964767] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0 <7> [34.964899] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0 <7> [34.965041] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0 <7> [34.965190] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0 <7> [34.965324] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no <6> [34.966495] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1 <6> [34.966499] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0 <7> [34.981191] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 11ms, freq = 100MHz, before = 100MHz, status = 0x8002F0EC, count = 0, ret = 0 <7> [34.982103] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <6> [34.993137] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads <6> [34.993141] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled <6> [34.993144] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled <7> [35.000820] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <7> [35.001022] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping <7> [35.001167] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping <7> [35.001298] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping <7> [35.001431] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [35.001585] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [35.002068] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [35.002181] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [35.002283] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [35.002384] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [35.006400] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event <7> [35.006815] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event <7> [35.007279] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1 <7> [35.008250] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event <6> [35.008300] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [35.010287] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <6> [35.026079] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [35.028178] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3 <7> [35.029565] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [35.030227] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [35.030475] [drm:drm_client_modeset_probe] <7> [35.030467] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [35.030701] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] <7> [35.030671] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [35.030724] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [35.030893] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [35.031627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [35.031655] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [35.031864] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9 <7> [35.031869] i915 device info: graphics version: 9 <7> [35.031871] i915 device info: media version: 9 <7> [35.031874] i915 device info: graphics stepping: F0 <7> [35.031876] i915 device info: media stepping: F0 <7> [35.031879] i915 device info: display stepping: C0 <7> [35.031881] i915 device info: base die stepping: <7> [35.031884] i915 device info: gt: 2 <7> [35.031886] i915 device info: memory-regions: 0x21 <7> [35.031888] i915 device info: page-sizes: 0x11000 <7> [35.031891] i915 device info: platform: KABYLAKE <7> [35.031893] i915 device info: ppgtt-size: 48 <7> [35.031896] i915 device info: ppgtt-type: 2 <7> [35.031898] i915 device info: dma_mask_size: 39 <7> [35.031901] i915 device info: is_mobile: no <7> [35.031903] i915 device info: is_lp: no <7> [35.031905] i915 device info: require_force_probe: no <7> [35.031908] i915 device info: is_dgfx: no <7> [35.031910] i915 device info: has_64bit_reloc: yes <7> [35.031913] i915 device info: has_64k_pages: no <7> [35.031915] i915 device info: gpu_reset_clobbers_display: no <7> [35.031918] i915 device info: has_reset_engine: yes <7> [35.031920] i915 device info: has_3d_pipeline: yes <7> [35.031922] i915 device info: has_4tile: no <7> [35.031925] i915 device info: has_flat_ccs: no <7> [35.031927] i915 device info: has_global_mocs: no <7> [35.031929] i915 device info: has_gmd_id: no <7> [35.031932] i915 device info: has_gt_uc: yes <7> [35.031934] i915 device info: has_heci_pxp: no <7> [35.031842] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [35.031937] i915 device info: has_heci_gscfi: no <7> [35.031939] i915 device info: has_guc_deprivilege: no <7> [35.031941] i915 device info: has_l3_ccs_read: no <7> [35.031943] i915 device info: has_l3_dpf: no <7> [35.031945] i915 device info: has_llc: yes <7> [35.031947] i915 device info: has_logical_ring_contexts: yes <7> [35.031949] i915 device info: has_logical_ring_elsq: no <7> [35.031951] i915 device info: has_media_ratio_mode: no <7> [35.031953] i915 device info: has_mslice_steering: no <7> [35.031955] i915 device info: has_oa_bpc_reporting: no <7> [35.031957] i915 device info: has_oa_slice_contrib_limits: no <7> [35.031958] i915 device info: has_oam: no <7> [35.031960] i915 device info: has_one_eu_per_fuse_bit: no <7> [35.031962] i915 device info: has_pxp: no <7> [35.031964] i915 device info: has_rc6: yes <7> [35.031966] i915 device info: has_rc6p: no <7> [35.031968] i915 device info: has_rps: yes <7> [35.031970] i915 device info: has_runtime_pm: yes <7> [35.031972] i915 device info: has_snoop: no <7> [35.031974] i915 device info: has_coherent_ggtt: yes <7> [35.031976] i915 device info: tuning_thread_rr_after_dep: no <7> [35.031978] i915 device info: unfenced_needs_alignment: no <7> [35.031980] i915 device info: hws_needs_physical: no <7> [35.031982] i915 device info: has_pooled_eu: no <7> [35.031984] i915 device info: rawclk rate: 24000 kHz <7> [35.031986] i915 device info: display version: 9 <7> [35.031988] i915 device info: cursor_needs_physical: no <7> [35.031990] i915 device info: has_cdclk_crawl: no <7> [35.031993] i915 device info: has_cdclk_squash: no <7> [35.032006] i915 device info: has_ddi: yes <7> [35.032008] i915 device info: has_dp_mst: yes <7> [35.032010] i915 device info: has_dsb: no <7> [35.032012] i915 device info: has_fpga_dbg: yes <7> [35.032014] i915 device info: has_gmch: no <7> [35.032016] i915 device info: has_hotplug: yes <7> [35.032018] i915 device info: has_hti: no <7> [35.032020] i915 device info: has_ipc: yes <7> [35.032022] i915 device info: has_overlay: no <7> [35.032024] i915 device info: has_psr: yes <7> [35.032026] i915 device info: has_psr_hw_tracking: yes <7> [35.032046] i915 device info: overlay_needs_physical: no <7> [35.032048] i915 device info: supports_tv: no <7> [35.032051] i915 device info: has_hdcp: yes <7> [35.032054] i915 device info: has_dmc: yes <7> [35.032069] i915 device info: has_dsc: no <7> [35.032071] i915 device info: iommu: enabled <7> [35.032076] i915 device info: available engines: 40403 <7> [35.032082] i915 device info: slice total: 1, mask=0001 <7> [35.032084] i915 device info: subslice total: 3 <7> [35.032090] i915 device info: slice0: 3 subslices, mask=00000007 <7> [35.032093] i915 device info: slice1: 0 subslices, mask=00000000 <7> [35.032098] i915 device info: slice2: 0 subslices, mask=00000000 <7> [35.032101] i915 device info: EU total: 24 <7> [35.032104] i915 device info: EU per subslice: 8 <7> [35.032107] i915 device info: has slice power gating: no <7> [35.032109] i915 device info: has subslice power gating: no <7> [35.032112] i915 device info: has EU power gating: yes <6> [35.032115] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [35.032118] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [35.032121] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [35.032467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [35.032668] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [35.032674] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [35.032852] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [35.035846] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [35.035853] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [35.036048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [35.036324] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [35.036474] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [35.036620] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [35.037234] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.037620] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected <7> [35.037779] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected <7> [35.037786] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] <7> [35.037791] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [35.037969] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.039119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [35.039316] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [35.039675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [35.040120] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [35.040126] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [35.040254] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [35.054899] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [35.054906] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [35.055080] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.055236] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected <7> [35.055246] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected <7> [35.055254] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] <7> [35.055262] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [35.055436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.055959] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.056133] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] status updated from unknown to disconnected <7> [35.056144] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected <7> [35.056150] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [35.056162] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [35.056166] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [35.056169] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [35.056252] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [35.056268] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [35.056286] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [35.056300] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [35.057060] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.057217] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [35.057718] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [35.058582] [drm:drm_client_modeset_probe] <7> [35.058729] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] <7> [35.058744] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [35.059349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [35.059467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [35.059765] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [35.059888] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [35.059893] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [35.060015] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [35.062886] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [35.062893] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [35.063062] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [35.063293] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [35.063418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [35.063975] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.064278] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected <7> [35.064288] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] <7> [35.064296] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [35.064480] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.065593] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [35.065715] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [35.066303] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [35.066817] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [35.066824] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [35.066978] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [35.081667] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [35.081676] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [35.081815] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.081949] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected <7> [35.081956] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] <7> [35.081962] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [35.082105] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.082601] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.082739] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected <7> [35.082744] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [35.082752] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [35.082756] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [35.082759] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [35.082825] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [35.082843] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [35.082861] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [35.082871] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [35.082952] [drm:drm_client_modeset_probe] <7> [35.082980] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] <7> [35.082986] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [35.083130] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.084173] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [35.084306] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [35.084884] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [35.085455] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [35.085463] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [35.085576] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [35.101854] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [35.101863] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [35.102102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.102293] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected <7> [35.102301] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] <7> [35.102309] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [35.102481] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.103556] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [35.103725] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [35.104073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [35.104533] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [35.104540] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [35.104697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [35.119908] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [35.119916] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [35.120140] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.120325] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected <7> [35.120333] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] <7> [35.120341] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [35.120509] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.120988] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [35.121186] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected <7> [35.121193] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [35.121199] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [35.121204] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [35.121208] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [35.121247] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [35.121259] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [35.121277] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <6> [35.121285] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <6> [35.155095] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <6> [35.158009] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [35.158412] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [35.158602] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [35.158711] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [35.159126] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [35.159674] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [35.159846] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [35.159991] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10 <7> [35.160850] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [35.172988] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [35.173053] [IGT] i915_module_load: exiting, ret=0 <6> [35.181243] i915_module_loa (923) used greatest stack depth: 11128 bytes left

<6> [34.296784] Console: switching to colour dummy device 80x25

<6> [34.296846] [IGT] i915_module_load: executing

<6> [34.304114] [IGT] i915_module_load: starting subtest load

<4> [34.833885] **********************************************************

<4> [34.833887] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [34.833890] ** trace_printk() being used. Allocating extra memory. **

<4> [34.833893] ** This means that this is a DEBUG kernel and it is **

<4> [34.833894] ** unsafe for production use. **

<4> [34.833897] ** If you see this message and you are not debugging **

<4> [34.833899] ** the kernel, report this immediately to your vendor! **

<4> [34.833902] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [34.833903] **********************************************************

<5> [34.845964] Setting dangerous option enable_guc - tainting kernel

<7> [34.891526] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K

<7> [34.891744] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no)

<6> [34.891896] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A

<7> [34.891908] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH

<7> [34.892085] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [34.892330] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [34.892452] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz

<7> [34.893176] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [34.893287] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [34.893392] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M

<6> [34.893494] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [34.895889] i915 0000:00:02.0: vgaarb: deactivate vga console

<6> [34.896660] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [34.896686] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047

<7> [34.896882] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K

<7> [34.897341] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018

<7> [34.897504] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0

<7> [34.897636] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [34.897767] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [34.897899] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [34.903038] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483

<7> [34.903195] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [34.903336] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [34.903477] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [34.903618] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [34.903728] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [34.903833] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [34.903936] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no

<7> [34.904054] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [34.904149] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [34.904241] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no

<7> [34.904333] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [34.904424] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [34.904515] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [34.904982] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [34.905155] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206

<7> [34.905306] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [34.905450] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)

<7> [34.905594] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [34.905742] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [34.905889] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)

<7> [34.906045] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)

<7> [34.906194] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [34.906342] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)

<7> [34.906489] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [34.906636] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)

<7> [34.906774] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [34.906916] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [34.907064] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [34.907212] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [34.907357] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [34.907504] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [34.907646] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [34.907789] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4

<7> [34.907930] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [34.908079] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8

<7> [34.908218] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [34.908356] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0

<7> [34.908496] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02

<7> [34.908650] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [34.908830] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [34.908988] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO

<7> [34.909151] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [34.909610] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz

<7> [34.909753] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz

<7> [34.909912] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [34.910115] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [34.910259] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [34.910398] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [34.910549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<6> [34.910703] i915 0000:00:02.0: vgaarb: VGA decodes changed: olddecodes=io+mem,decodes=io+mem:owns=io+mem

<7> [34.910748] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [34.910890] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [34.911043] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [34.911187] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [34.911399] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin

<7> [34.912854] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [34.913415] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV

<7> [34.913618] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us

<7> [34.913818] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [34.914024] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [34.914219] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [34.914424] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [34.914617] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [34.914811] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [34.915057] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [34.915210] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<7> [34.917008] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [34.918611] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0

<7> [34.918952] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind

<6> [34.919130] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

<7> [34.919274] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B]

<7> [34.919405] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT)

<7> [34.919835] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C]

<7> [34.919964] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT)

<7> [34.920198] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] Using AUX CH A (VBT)

<6> [34.920370] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)

<7> [34.920343] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E]

<7> [34.920590] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [34.920920] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled

<7> [34.921121] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled

<7> [34.921283] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled

<7> [34.921425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [34.921566] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A

<7> [34.921710] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A

<7> [34.921853] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B

<7> [34.922006] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B

<7> [34.922151] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B

<7> [34.922292] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C

<7> [34.922437] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C

<7> [34.922580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C

<7> [34.922725] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [34.922868] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A

<7> [34.923023] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A

<7> [34.923166] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1

<7> [34.923316] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [34.923465] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [34.923613] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [34.923825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled

<7> [34.923981] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled

<7> [34.924154] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled

<7> [34.924291] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [34.924425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz

<7> [34.924560] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz

<7> [34.924693] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [34.924838] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz

<7> [34.924978] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz

<7> [34.925125] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz

<7> [34.925264] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [34.925410] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz

<7> [34.925547] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz

<7> [34.925684] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz

<7> [34.925820] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [34.926018] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]

<7> [34.926165] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]

<7> [34.926310] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]

<7> [34.926453] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling

<7> [34.926596] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [34.926734] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [34.926870] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [34.932172] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [240K, 784K)

<7> [34.932312] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [34.932425] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]

<7> [34.932545] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0

<7> [34.932679] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global

<7> [34.933701] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0

<7> [34.933844] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0

<7> [34.933978] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0

<7> [34.936453] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)

<7> [34.936629] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs.

<7> [34.936791] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset

<7> [34.963353] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f

<7> [34.963528] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0

<7> [34.963667] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000

<7> [34.963800] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3

<7> [34.963933] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a

<7> [34.964081] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004

<7> [34.964234] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0

<7> [34.964368] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0

<7> [34.964501] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0

<7> [34.964634] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0

<7> [34.964767] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0

<7> [34.964899] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0

<7> [34.965041] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0

<7> [34.965190] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0

<7> [34.965324] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no

<6> [34.966495] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1

<6> [34.966499] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0

<7> [34.981191] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 11ms, freq = 100MHz, before = 100MHz, status = 0x8002F0EC, count = 0, ret = 0

<7> [34.982103] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<6> [34.993137] i915 0000:00:02.0: [drm] GT0: HuC: authenticated for all workloads

<6> [34.993141] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled

<6> [34.993144] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled

<7> [35.000820] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV

<7> [35.001022] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping

<7> [35.001167] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping

<7> [35.001298] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping

<7> [35.001431] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [35.001585] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [35.002068] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [35.002181] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [35.002283] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [35.002384] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [35.006400] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event

<7> [35.006815] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event

<7> [35.007279] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1

<7> [35.008250] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event

<6> [35.008300] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [35.010287] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected

<6> [35.026079] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [35.028178] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3

<7> [35.029565] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)

<7> [35.030227] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D

<7> [35.030475] [drm:drm_client_modeset_probe]

<7> [35.030467] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C

<7> [35.030701] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]

<7> [35.030671] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B

<7> [35.030724] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [35.030893] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E

<7> [35.031627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [35.031655] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [35.031864] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9

<7> [35.031869] i915 device info: graphics version: 9

<7> [35.031871] i915 device info: media version: 9

<7> [35.031874] i915 device info: graphics stepping: F0

<7> [35.031876] i915 device info: media stepping: F0

<7> [35.031879] i915 device info: display stepping: C0

<7> [35.031881] i915 device info: base die stepping: **

<7> [35.031886] i915 device info: memory-regions: 0x21

<7> [35.031888] i915 device info: page-sizes: 0x11000

<7> [35.031891] i915 device info: platform: KABYLAKE

<7> [35.031893] i915 device info: ppgtt-size: 48

<7> [35.031896] i915 device info: ppgtt-type: 2

<7> [35.031898] i915 device info: dma_mask_size: 39

<7> [35.031901] i915 device info: is_mobile: no

<7> [35.031903] i915 device info: is_lp: no

<7> [35.031905] i915 device info: require_force_probe: no

<7> [35.031908] i915 device info: is_dgfx: no

<7> [35.031910] i915 device info: has_64bit_reloc: yes

<7> [35.031913] i915 device info: has_64k_pages: no

<7> [35.031915] i915 device info: gpu_reset_clobbers_display: no

<7> [35.031918] i915 device info: has_reset_engine: yes

<7> [35.031920] i915 device info: has_3d_pipeline: yes

<7> [35.031922] i915 device info: has_4tile: no

<7> [35.031925] i915 device info: has_flat_ccs: no

<7> [35.031927] i915 device info: has_global_mocs: no

<7> [35.031929] i915 device info: has_gmd_id: no

<7> [35.031932] i915 device info: has_gt_uc: yes

<7> [35.031934] i915 device info: has_heci_pxp: no

<7> [35.031842] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [35.031937] i915 device info: has_heci_gscfi: no

<7> [35.031939] i915 device info: has_guc_deprivilege: no

<7> [35.031941] i915 device info: has_l3_ccs_read: no

<7> [35.031943] i915 device info: has_l3_dpf: no

<7> [35.031945] i915 device info: has_llc: yes

<7> [35.031947] i915 device info: has_logical_ring_contexts: yes

<7> [35.031949] i915 device info: has_logical_ring_elsq: no

<7> [35.031951] i915 device info: has_media_ratio_mode: no

<7> [35.031953] i915 device info: has_mslice_steering: no

<7> [35.031955] i915 device info: has_oa_bpc_reporting: no

<7> [35.031957] i915 device info: has_oa_slice_contrib_limits: no

<7> [35.031958] i915 device info: has_oam: no

<7> [35.031960] i915 device info: has_one_eu_per_fuse_bit: no

<7> [35.031962] i915 device info: has_pxp: no

<7> [35.031964] i915 device info: has_rc6: yes

<7> [35.031966] i915 device info: has_rc6p: no

<7> [35.031968] i915 device info: has_rps: yes

<7> [35.031970] i915 device info: has_runtime_pm: yes

<7> [35.031972] i915 device info: has_snoop: no

<7> [35.031974] i915 device info: has_coherent_ggtt: yes

<7> [35.031976] i915 device info: tuning_thread_rr_after_dep: no

<7> [35.031978] i915 device info: unfenced_needs_alignment: no

<7> [35.031980] i915 device info: hws_needs_physical: no

<7> [35.031982] i915 device info: has_pooled_eu: no

<7> [35.031984] i915 device info: rawclk rate: 24000 kHz

<7> [35.031986] i915 device info: display version: 9

<7> [35.031988] i915 device info: cursor_needs_physical: no

<7> [35.031990] i915 device info: has_cdclk_crawl: no

<7> [35.031993] i915 device info: has_cdclk_squash: no

<7> [35.032006] i915 device info: has_ddi: yes

<7> [35.032008] i915 device info: has_dp_mst: yes

<7> [35.032010] i915 device info: has_dsb: no

<7> [35.032012] i915 device info: has_fpga_dbg: yes

<7> [35.032014] i915 device info: has_gmch: no

<7> [35.032016] i915 device info: has_hotplug: yes

<7> [35.032018] i915 device info: has_hti: no

<7> [35.032020] i915 device info: has_ipc: yes

<7> [35.032022] i915 device info: has_overlay: no

<7> [35.032024] i915 device info: has_psr: yes

<7> [35.032026] i915 device info: has_psr_hw_tracking: yes

<7> [35.032046] i915 device info: overlay_needs_physical: no

<7> [35.032048] i915 device info: supports_tv: no

<7> [35.032051] i915 device info: has_hdcp: yes

<7> [35.032054] i915 device info: has_dmc: yes

<7> [35.032069] i915 device info: has_dsc: no

<7> [35.032071] i915 device info: iommu: enabled

<7> [35.032076] i915 device info: available engines: 40403

<7> [35.032082] i915 device info: slice total: 1, mask=0001

<7> [35.032084] i915 device info: subslice total: 3

<7> [35.032090] i915 device info: slice0: 3 subslices, mask=00000007

<7> [35.032093] i915 device info: slice1: 0 subslices, mask=00000000

<7> [35.032098] i915 device info: slice2: 0 subslices, mask=00000000

<7> [35.032101] i915 device info: EU total: 24

<7> [35.032104] i915 device info: EU per subslice: 8

<7> [35.032107] i915 device info: has slice power gating: no

<7> [35.032109] i915 device info: has subslice power gating: no

<7> [35.032112] i915 device info: has EU power gating: yes

<6> [35.032115] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled

<6> [35.032118] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [35.032121] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [35.032467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [35.032668] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [35.032674] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [35.032852] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [35.035846] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [35.035853] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [35.036048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [35.036324] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [35.036474] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [35.036620] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [35.037234] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.037620] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected

<7> [35.037779] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [35.037786] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]

<7> [35.037791] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [35.037969] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.039119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [35.039316] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [35.039675] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [35.040120] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [35.040126] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [35.040254] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [35.054899] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [35.054906] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [35.055080] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.055236] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected

<7> [35.055246] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [35.055254] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]

<7> [35.055262] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [35.055436] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.055959] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.056133] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] status updated from unknown to disconnected

<7> [35.056144] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected

<7> [35.056150] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [35.056162] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [35.056166] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [35.056169] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [35.056252] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [35.056268] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [35.056286] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<6> [35.056300] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [35.057060] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.057217] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [35.057718] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [35.058582] [drm:drm_client_modeset_probe]

<7> [35.058729] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]

<7> [35.058744] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [35.059349] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [35.059467] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [35.059765] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [35.059888] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [35.059893] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [35.060015] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [35.062886] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [35.062893] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [35.063062] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [35.063293] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [35.063418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [35.063975] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.064278] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [35.064288] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]

<7> [35.064296] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [35.064480] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.065593] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [35.065715] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [35.066303] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [35.066817] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [35.066824] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [35.066978] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [35.081667] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [35.081676] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [35.081815] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.081949] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [35.081956] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]

<7> [35.081962] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [35.082105] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.082601] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.082739] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected

<7> [35.082744] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [35.082752] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [35.082756] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [35.082759] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [35.082825] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [35.082843] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [35.082861] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<6> [35.082871] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [35.082952] [drm:drm_client_modeset_probe]

<7> [35.082980] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1]

<7> [35.082986] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [35.083130] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.084173] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [35.084306] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [35.084884] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [35.085455] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [35.085463] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [35.085576] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [35.101854] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [35.101863] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [35.102102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.102293] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [35.102301] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2]

<7> [35.102309] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [35.102481] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.103556] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [35.103725] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [35.104073] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [35.104533] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [35.104540] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [35.104697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [35.119908] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [35.119916] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [35.120140] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.120325] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [35.120333] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1]

<7> [35.120341] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [35.120509] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.120988] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [35.121186] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:109:DP-1] disconnected

<7> [35.121193] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [35.121199] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [35.121204] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [35.121208] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [35.121247] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [35.121259] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [35.121277] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<6> [35.121285] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<6> [35.155095] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)

<6> [35.158009] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [35.158412] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [35.158602] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [35.158711] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [35.159126] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [35.159674] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [35.159846] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [35.159991] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10

<7> [35.160850] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<6> [35.172988] [IGT] i915_module_load: finished subtest load, SUCCESS

<6> [35.173053] [IGT] i915_module_load: exiting, ret=0

<6> [35.181243] i915_module_loa (923) used greatest stack depth: 11128 bytes left

Results for igt@i915_module_load@load