Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-g605d12880 (x86_64) (Linux: 6.6.0-rc1-linus-v6.6-rc1-g0bb80ecc33a8+ x86_64) |
| Out |
Opened device: /dev/dri/card0 Starting subtest: unused-offsets Subtest unused-offsets: SUCCESS (0.000s) |
| Err |
Starting subtest: unused-offsets Subtest unused-offsets: SUCCESS (0.000s) |
| Dmesg |
<6> [82.785585] Console: switching to colour dummy device 80x25
<6> [82.785619] [IGT] kms_addfb_basic: executing
<7> [82.788165] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [82.788631] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [82.788770] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [82.789045] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000)
<7> [82.789139] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:281]
<6> [82.789169] [IGT] kms_addfb_basic: starting subtest unused-offsets
<7> [82.789194] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] non-zero offset for unused plane 1
<6> [82.789218] [IGT] kms_addfb_basic: finished subtest unused-offsets, SUCCESS
<7> [82.789323] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:281]
<7> [82.789362] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:281]
<7> [82.796141] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
<7> [82.796148] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [82.796312] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
<7> [82.796688] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [82.796692] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [82.848136] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [82.865210] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [82.865216] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.865328] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [82.881221] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [82.881224] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [82.881322] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [82.881777] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2]
<7> [82.881781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [82.881933] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2] disconnected
<7> [82.882318] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3]
<7> [82.882321] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [82.882455] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3] disconnected
<7> [82.882946] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1]
<7> [82.882950] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [82.883757] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00 00
<7> [82.883859] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [82.884499] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [82.884596] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [82.884691] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [82.884786] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [82.884894] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [82.884898] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [82.884901] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [82.884904] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [82.884932] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [82.885042] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [82.885827] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [82.885938] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [82.886613] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:236:eDP-1] probed modes :
<7> [82.886617] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [82.886621] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [82.886636] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1]
<7> [82.886639] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [82.886783] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:246:DP-1] disconnected
<7> [82.886796] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1]
<7> [82.886799] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [82.898064] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [82.898245] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [82.909122] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out after NAK
<7> [82.909403] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] NAK for addr: 0050 w(1)
<7> [82.960125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [82.977268] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [82.977272] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [82.977385] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [82.994253] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [82.994256] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [82.994352] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [82.994378] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2]
<7> [82.994383] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [82.994560] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:264:DP-2] disconnected
<7> [82.994572] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3]
<7> [82.994575] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [82.994712] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:273:DP-3] disconnected
<6> [82.995014] [IGT] kms_addfb_basic: exiting, ret=0
<7> [82.995200] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [83.047567] Console: switching to colour frame buffer device 240x67
|