Results for igt@kms_addfb_basic@addfb25-x-tiled-legacy

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g605d12880 (x86_64) (Linux: 6.6.0-rc1-linus-v6.6-rc1-g0bb80ecc33a8+ x86_64)
Out	Opened device: /dev/dri/card0 Starting subtest: addfb25-x-tiled-legacy Subtest addfb25-x-tiled-legacy: SUCCESS (0.000s)
Err	Starting subtest: addfb25-x-tiled-legacy Subtest addfb25-x-tiled-legacy: SUCCESS (0.000s)
Dmesg	<6> [92.441101] [IGT] kms_addfb_basic: executing <7> [92.445287] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [92.446088] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [92.446343] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [92.446728] i915 0000:00:02.0: [drm:drm_internal_framebuffer_create] bad framebuffer format .... little-endian (0x00000000) <7> [92.446899] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <7> [92.447128] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <7> [92.447237] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <6> [92.447468] [IGT] kms_addfb_basic: starting subtest addfb25-x-tiled-legacy <7> [92.447522] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:118] <6> [92.447590] [IGT] kms_addfb_basic: finished subtest addfb25-x-tiled-legacy, SUCCESS <7> [92.454328] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [92.454338] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [92.454619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [92.455223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [92.456088] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [92.456677] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [92.457442] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [92.457649] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [92.458592] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.460223] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.461839] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.463432] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.465182] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.466987] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.468762] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.470433] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.472086] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.472981] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [92.473906] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [92.474581] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [92.475051] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [92.475365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [92.475628] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [92.475845] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [92.476526] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [92.476746] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [92.477637] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [92.477645] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [92.477910] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [92.478474] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [92.478718] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [92.479574] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [92.479583] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [92.479791] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [92.530614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [92.549431] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [92.549450] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [92.549773] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [92.567996] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [92.568005] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [92.568196] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [92.568453] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <7> [92.569177] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] <7> [92.569186] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [92.569418] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [92.569986] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [92.570643] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [92.571293] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [92.572088] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [92.572350] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [92.573320] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.574939] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.576594] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.578245] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.580026] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.581761] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.583592] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.585433] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.587043] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [92.587941] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [92.588826] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [92.589472] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [92.590024] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [92.590414] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [92.590739] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [92.591061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [92.591865] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [92.592204] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:95:DP-1] disconnected <7> [92.592256] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] <7> [92.592266] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [92.592600] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [92.593249] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [92.593603] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:108:DP-2] disconnected <7> [92.593646] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] <7> [92.593655] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [92.593959] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [92.645610] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [92.664366] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [92.664381] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [92.664762] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [92.683096] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [92.683106] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [92.683329] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [92.683619] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:114:HDMI-A-1] disconnected <6> [92.684548] [IGT] kms_addfb_basic: exiting, ret=0 <7> [92.685121] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-09-11 01:21:38