igt@i915_module_load@reload on bat-jsl-3@linus-v6.6-rc1 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g605d12880 (x86_64) (Linux: 6.6.0-rc1-linus-v6.6-rc1-g0bb80ecc33a8+ x86_64)
Out	Starting subtest: reload Opened device: /dev/dri/card0 Subtest reload: SUCCESS (3.434s)
Err	Starting subtest: reload Subtest reload: SUCCESS (3.434s)
Dmesg	<6> [300.770657] Console: switching to colour dummy device 80x25 <6> [300.771598] [IGT] i915_module_load: executing <6> [300.777004] [IGT] i915_module_load: starting subtest reload <7> [301.048961] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind <7> [301.125798] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [301.126578] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [301.127427] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [301.128275] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [301.129091] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [301.129920] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [301.130660] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [301.131486] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [301.132510] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [301.133201] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [301.134230] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [301.138748] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 1, found 0) <7> [301.139468] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 1, found 0) <7> [301.139854] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1) <7> [301.140174] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 4, found 0) <7> [301.140497] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0) <7> [301.140827] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000) <7> [301.141139] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0) <7> [301.141456] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0) <7> [301.142276] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3316, found 0) <7> [301.142631] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0) <7> [301.142999] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0) <7> [301.143313] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0) <7> [301.143612] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0) <7> [301.143934] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0) <7> [301.144244] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1816, found 0) <7> [301.144559] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0) <7> [301.144900] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0) <7> [301.145209] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0) <7> [301.145517] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0) <7> [301.145839] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0) <7> [301.146146] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3316, found 0) <7> [301.146447] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0) <7> [301.146742] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0) <7> [301.147073] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0) <7> [301.147399] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0) <7> [301.147708] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0) <7> [301.148028] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0) <7> [301.148333] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0) <7> [301.148633] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0) <7> [301.148945] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0) <7> [301.149254] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0) <7> [301.149567] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0) <7> [301.149904] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0) <7> [301.150213] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0) <7> [301.150518] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0) <7> [301.150834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 361310, found 0) <7> [301.151136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 361310, found 0) <7> [301.151430] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 540000, found 0) <7> [301.151739] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [301.152083] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0 <7> [301.152458] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [301.152870] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0 <7> [301.153163] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0 <7> [301.153446] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [301.153725] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [301.154038] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [301.154343] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [301.154644] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0 <7> [301.154972] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [301.155281] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0 <7> [301.155580] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0 <7> [301.155938] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [301.156246] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [301.156559] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [301.156909] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset] <7> [301.157226] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [301.157528] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [301.157843] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [301.158141] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [301.158433] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [301.158737] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [301.159070] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [301.159392] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [301.178800] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [301.382215] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0 <7> [301.383263] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [301.391019] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [301.391905] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [301.393019] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off <7> [301.393722] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time <7> [301.394493] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [301.399283] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [301.400041] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [301.400739] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [301.401840] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [301.420647] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [301.421447] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [301.422173] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20 <7> [301.422941] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [301.448120] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [301.448893] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [301.448958] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [301.449656] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [301.449721] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A] <7> [301.450347] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30 <7> [301.450557] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [301.451359] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [301.451502] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [301.452156] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A] <7> [301.452932] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [301.453936] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [301.454669] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [301.455391] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [301.456133] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [301.456861] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [301.457558] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [301.458283] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [301.459070] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [301.459833] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [301.460568] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [301.461840] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [301.502598] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915] <7> [301.580807] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper <7> [301.581833] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [302.054328] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [302.055182] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <6> [302.560268] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0 <4> [302.560292] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID) <4> [302.560298] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000 <4> [302.560303] nvme 0000:02:00.0: [ 0] RxErr (First) <7> [303.112940] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K <7> [303.113437] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no) <7> [303.113867] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH <7> [303.114316] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [303.114941] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [303.115328] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz <7> [303.116315] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001 <7> [303.116634] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001 <7> [303.117465] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [303.117817] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [303.118120] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M <6> [303.118417] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [303.118426] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [303.119070] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [303.119107] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7 <7> [303.119455] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K <7> [303.120222] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018 <7> [303.120631] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0 <7> [303.121005] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [303.121358] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [303.121700] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [303.129845] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583 <7> [303.130261] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [303.130604] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [303.130970] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [303.131351] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [303.131698] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no <7> [303.132047] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [303.132361] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no <7> [303.132652] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no <7> [303.132956] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [303.133246] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no <7> [303.133525] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [303.133941] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [303.134243] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [303.134534] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50 <7> [303.134937] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68 <7> [303.135331] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56 <7> [303.135715] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834 <7> [303.136178] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941 <7> [303.136548] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878 <7> [303.136933] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899 <7> [303.137301] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488 <7> [303.137687] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583 <7> [303.138097] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069 <7> [303.138467] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719 <7> [303.138849] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483 <7> [303.139208] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280 <7> [303.139562] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000 <7> [303.139962] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000 <7> [303.140350] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000 <7> [303.140709] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000 <7> [303.141089] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000 <7> [303.141453] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000 <7> [303.141814] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000 <7> [303.142173] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000 <7> [303.143846] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [303.144260] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228 <7> [303.144644] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [303.145091] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5) <7> [303.145471] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [303.145866] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [303.146225] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812) <7> [303.146585] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34) <7> [303.147216] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [303.147598] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366) <7> [303.147988] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [303.148353] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78) <7> [303.148717] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822) <7> [303.149269] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [303.149635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [303.150014] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806 <7> [303.150467] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6 <7> [303.150865] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [303.151245] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [303.151608] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [303.151976] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [303.152332] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000 <7> [303.152678] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [303.153049] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0 <7> [303.153414] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000 <7> [303.153816] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [303.154193] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0 <7> [303.154543] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000 <7> [303.154909] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a <7> [303.155302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [303.155714] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [303.156310] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [303.156686] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [303.157076] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [303.157443] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [303.158029] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [303.158503] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [303.159046] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [303.159411] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [303.160093] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [303.160481] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [303.160873] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [303.161282] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [303.161651] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [303.162031] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [303.162402] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [303.162772] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [303.163136] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [303.163478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [303.163850] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [303.164333] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4 <7> [303.164876] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin <7> [303.166685] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <6> [303.167613] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9) <7> [303.167731] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us <7> [303.168196] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [303.168556] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [303.168929] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [303.169301] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [303.169672] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [303.170059] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [303.170423] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [303.170787] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [303.186686] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [303.192854] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [303.193419] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz <7> [303.193835] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz <7> [303.194300] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT) <7> [303.194713] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A] <7> [303.199881] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0) <7> [303.200294] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [303.200663] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [303.201097] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless <7> [303.201517] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [303.201932] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [303.202304] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002 <7> [303.202692] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [303.203078] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [303.203453] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7> [303.204013] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0 <7> [303.204460] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000 <7> [303.204831] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [303.205195] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [303.205549] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [303.205938] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [303.206410] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [303.206957] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [303.207598] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [303.208024] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [303.208488] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [303.208875] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [303.209296] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [303.209651] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled <7> [303.416069] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [303.416954] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001 <7> [303.417805] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6 <7> [303.419503] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1 <7> [303.428043] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.430050] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.432058] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.434156] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.435956] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.438520] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.440476] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.442477] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer <7> [303.444183] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [303.444217] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [303.444237] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [303.444472] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [303.445477] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [303.446382] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms) <7> [303.455596] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none <7> [303.456859] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0) <7> [303.458127] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000 <7> [303.459593] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000 <7> [303.460468] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [303.461325] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [303.462507] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [303.463371] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [303.464333] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [303.466523] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT) <7> [303.467544] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B] <7> [303.469483] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [303.470453] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B] <7> [303.471336] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT) <7> [303.472903] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C] <7> [303.473724] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT) <7> [303.476345] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled <7> [303.477553] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled <7> [303.478727] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled <7> [303.479666] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [303.480604] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A <7> [303.481520] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A <7> [303.482420] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A <7> [303.483333] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A <7> [303.484257] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A <7> [303.485170] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A <7> [303.486077] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A <7> [303.486967] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B <7> [303.487879] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B <7> [303.488814] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B <7> [303.489687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B <7> [303.490584] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B <7> [303.491476] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B <7> [303.492378] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B <7> [303.493306] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B <7> [303.494257] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C <7> [303.495146] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C <7> [303.496030] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C <7> [303.496935] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C <7> [303.497847] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C <7> [303.498726] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C <7> [303.499624] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C <7> [303.500471] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C <7> [303.501213] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A <7> [303.501960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A <7> [303.502621] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A <7> [303.503314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B <7> [303.504002] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C <7> [303.504696] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A <7> [303.505447] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0 <7> [303.506205] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [303.506940] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0 <7> [303.507668] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled <7> [303.508264] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled <7> [303.508865] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled <7> [303.509413] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled <7> [303.509950] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [303.510462] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz <7> [303.510982] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz <7> [303.511506] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz <7> [303.512061] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz <7> [303.512590] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz <7> [303.513125] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz <7> [303.513630] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz <7> [303.514168] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [303.514657] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz <7> [303.515092] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz <7> [303.515491] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz <7> [303.515904] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz <7> [303.516290] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz <7> [303.516687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz <7> [303.517122] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz <7> [303.517535] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz <7> [303.517956] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [303.518381] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz <7> [303.518785] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz <7> [303.519188] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz <7> [303.519598] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz <7> [303.520043] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz <7> [303.520446] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz <7> [303.520879] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz <7> [303.521300] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz <7> [303.521637] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [303.546917] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state] <7> [303.547372] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state] <7> [303.547787] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state] <7> [303.548199] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [303.548623] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [303.549049] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [303.550077] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [303.550628] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000] <7> [303.551259] MCR Steering: Default steering: group=0x0, instance=0x0 <7> [303.551306] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global <7> [303.555557] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0 <7> [303.556258] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0 <7> [303.556805] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0 <7> [303.561232] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0 <7> [303.562557] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0 <7> [303.564594] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0 <7> [303.585631] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping <7> [303.586074] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping <7> [303.586442] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping <7> [303.586820] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [303.587281] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [303.589057] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [303.589399] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [303.589722] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [303.590087] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [303.596739] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered <7> [303.597411] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7> [303.600286] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event <7> [303.601172] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1 <7> [303.602792] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event <7> [303.603591] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event <7> [303.604366] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event <6> [303.604465] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [303.608443] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <6> [303.640565] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [303.648269] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input14 <7> [303.649827] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810) <6> [303.650203] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [303.651041] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4 <7> [303.651796] [drm:drm_client_modeset_probe] <7> [303.651872] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] <7> [303.651891] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [303.655598] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [303.655853] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [303.656132] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11 <7> [303.656140] i915 device info: graphics version: 11 <7> [303.656143] i915 device info: media version: 11 <7> [303.656146] i915 device info: graphics stepping: B0 <7> [303.656150] i915 device info: media stepping: B0 <7> [303.656153] i915 device info: display stepping: B0 <7> [303.656155] i915 device info: base die stepping: * <7> [303.656158] i915 device info: gt: 0 <7> [303.656161] i915 device info: memory-regions: 0x21 <7> [303.656164] i915 device info: page-sizes: 0x211000 <7> [303.656168] i915 device info: platform: JASPERLAKE <7> [303.656171] i915 device info: ppgtt-size: 36 <7> [303.656174] i915 device info: ppgtt-type: 2 <7> [303.656177] i915 device info: dma_mask_size: 39 <7> [303.656180] i915 device info: is_mobile: no <7> [303.656183] i915 device info: is_lp: no <7> [303.656185] i915 device info: require_force_probe: no <7> [303.656188] i915 device info: is_dgfx: no <7> [303.656191] i915 device info: has_64bit_reloc: yes <7> [303.656194] i915 device info: has_64k_pages: no <7> [303.656197] i915 device info: gpu_reset_clobbers_display: no <7> [303.656200] i915 device info: has_reset_engine: yes <7> [303.656203] i915 device info: has_3d_pipeline: yes <7> [303.656206] i915 device info: has_4tile: no <7> [303.656209] i915 device info: has_flat_ccs: no <7> [303.656212] i915 device info: has_global_mocs: no <7> [303.656215] i915 device info: has_gmd_id: no <7> [303.656218] i915 device info: has_gt_uc: yes <7> [303.656221] i915 device info: has_heci_pxp: no <7> [303.656238] i915 device info: has_heci_gscfi: no <7> [303.656242] i915 device info: has_guc_deprivilege: no <7> [303.656245] i915 device info: has_l3_ccs_read: no <7> [303.656249] i915 device info: has_l3_dpf: no <7> [303.656252] i915 device info: has_llc: yes <7> [303.656255] i915 device info: has_logical_ring_contexts: yes <7> [303.656259] i915 device info: has_logical_ring_elsq: yes <7> [303.656262] i915 device info: has_media_ratio_mode: no <7> [303.656266] i915 device info: has_mslice_steering: no <7> [303.656269] i915 device info: has_oa_bpc_reporting: no <7> [303.656273] i915 device info: has_oa_slice_contrib_limits: no <7> [303.656276] i915 device info: has_oam: no <7> [303.656280] i915 device info: has_one_eu_per_fuse_bit: no <7> [303.656283] i915 device info: has_pxp: no <7> [303.656286] i915 device info: has_rc6: yes <7> [303.656290] i915 device info: has_rc6p: no <7> [303.656293] i915 device info: has_rps: yes <7> [303.656296] i915 device info: has_runtime_pm: yes <7> [303.656300] i915 device info: has_snoop: no <7> [303.656303] i915 device info: has_coherent_ggtt: no <7> [303.656306] i915 device info: tuning_thread_rr_after_dep: no <7> [303.656310] i915 device info: unfenced_needs_alignment: no <7> [303.656313] i915 device info: hws_needs_physical: no <7> [303.656317] i915 device info: has_pooled_eu: no <7> [303.656320] i915 device info: rawclk rate: 19200 kHz <7> [303.656324] i915 device info: display version: 11 <7> [303.656328] i915 device info: cursor_needs_physical: no <7> [303.656331] i915 device info: has_cdclk_crawl: no <7> [303.656335] i915 device info: has_cdclk_squash: no <7> [303.656338] i915 device info: has_ddi: yes <7> [303.656341] i915 device info: has_dp_mst: yes <7> [303.656345] i915 device info: has_dsb: no <7> [303.656348] i915 device info: has_fpga_dbg: yes <7> [303.656352] i915 device info: has_gmch: no <7> [303.656355] i915 device info: has_hotplug: yes <7> [303.656358] i915 device info: has_hti: no <7> [303.656362] i915 device info: has_ipc: yes <7> [303.656365] i915 device info: has_overlay: no <7> [303.656368] i915 device info: has_psr: yes <7> [303.656372] i915 device info: has_psr_hw_tracking: yes <7> [303.656375] i915 device info: overlay_needs_physical: no <7> [303.656378] i915 device info: supports_tv: no <7> [303.656382] i915 device info: has_hdcp: no <7> [303.656385] i915 device info: has_dmc: yes <7> [303.656388] i915 device info: has_dsc: yes <7> [303.656392] i915 device info: iommu: enabled <7> [303.656396] i915 device info: available engines: 40403 <7> [303.656400] i915 device info: slice total: 1, mask=0001 <7> [303.656404] i915 device info: subslice total: 4 <7> [303.656408] i915 device info: slice0: 4 subslices, mask=0000000f <7> [303.656230] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [303.656413] i915 device info: EU total: 16 <7> [303.656416] i915 device info: EU per subslice: 4 <7> [303.656419] i915 device info: has slice power gating: yes <7> [303.656421] i915 device info: has subslice power gating: yes <7> [303.656424] i915 device info: has EU power gating: yes <6> [303.656428] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [303.656432] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [303.656435] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [303.656608] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [303.657593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [303.658196] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [303.658212] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [303.658221] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [303.658258] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [303.658626] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [303.660355] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [303.663323] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [303.665073] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [303.666076] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [303.667438] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to connected <7> [303.667629] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes : <7> [303.667639] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [303.667651] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [303.668096] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] <7> [303.668115] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [303.670573] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected <7> [303.670607] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected <7> [303.670622] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] <7> [303.670638] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [303.671161] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected <7> [303.671182] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected <7> [303.671192] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [303.671203] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [303.671620] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected <7> [303.671639] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [303.671648] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [303.671656] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [303.671662] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [303.671668] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [303.671732] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [303.671767] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [303.671775] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [303.671781] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [303.671787] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [303.671808] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <7> [303.671846] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane <7> [303.671969] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one <6> [303.696350] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <7> [303.696482] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00100000 <6> [303.697642] fbcon: i915drmfb (fb0) is primary device <7> [303.698961] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [303.699449] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz <7> [303.699885] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24 <7> [303.700271] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000 <7> [303.700650] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no <7> [303.701062] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long <7> [303.701436] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [303.701839] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A] <7> [303.702203] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1) <7> [303.702580] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1) <7> [303.705783] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4) <7> [303.706216] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4) <7> [303.706595] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288) <7> [303.707017] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100) <7> [303.707416] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1) <7> [303.707834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200) <7> [303.708215] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316) <7> [303.708582] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200) <7> [303.708995] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316) <7> [303.709368] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248) <7> [303.709734] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280) <7> [303.710136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800) <7> [303.710511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816) <7> [303.710913] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800) <7> [303.711286] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816) <7> [303.711660] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802) <7> [303.712056] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807) <7> [303.712447] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200) <7> [303.712853] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316) <7> [303.713218] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200) <7> [303.713581] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316) <7> [303.713960] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248) <7> [303.714331] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280) <7> [303.714710] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800) <7> [303.715136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816) <7> [303.715516] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800) <7> [303.715901] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816) <7> [303.716263] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802) <7> [303.716614] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807) <7> [303.716997] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1) <7> [303.717372] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2) <7> [303.717743] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8) <7> [303.718159] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b) <7> [303.718525] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x00e001a5) <7> [303.718912] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24) <7> [303.719280] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310) <7> [303.719654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310) <7> [303.720071] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000) <7> [303.720459] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [303.720922] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1 <7> [303.721333] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985 <7> [303.721692] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39 <7> [303.722085] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,*twm, swm, stwm <7> [303.722470] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [303.722890] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 <7> [303.723273] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 <7> [303.723642] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1 <7> [303.724046] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [303.724419] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446 <7> [303.724812] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446 <7> [303.725227] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz) <7> [303.725602] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz) <7> [303.726009] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [303.726377] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz <7> [303.726762] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1 <7> [303.727139] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0 <7> [303.727533] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0 <7> [303.727951] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset] <7> [303.728321] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [303.728690] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [303.729083] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [303.729452] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [303.729859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [303.730254] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [303.730614] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64 <7> [303.731003] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [303.731371] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [303.731729] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [303.732125] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [303.732508] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [303.732906] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [303.733297] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [303.733677] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [303.734076] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [303.734441] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310 <7> [303.734812] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0 <7> [303.735174] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [303.735562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [303.735956] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [303.736325] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [303.736692] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [303.737089] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [303.737464] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [303.737860] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [303.738239] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [303.738629] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [303.739023] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [303.739375] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [303.739782] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [303.740147] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [303.740510] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [303.740903] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [303.741279] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [303.741646] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [303.742040] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0 <7> [303.742422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [303.742840] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [303.743208] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [303.743562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [303.743932] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [303.744292] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [303.744656] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [303.745534] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1 <7> [303.746570] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [303.747002] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [303.747383] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [303.747741] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [303.748141] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [303.748506] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [303.748898] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [303.749558] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [303.749988] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [303.750539] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A] <7> [303.750967] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [303.752592] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on <7> [303.753255] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [303.753714] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [303.754120] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [303.754529] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on <7> [303.754984] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b <7> [303.965121] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [303.966212] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [303.971929] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [303.972052] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14 <7> [303.973807] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [303.974985] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [303.977381] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0 <7> [303.978247] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0 <7> [303.980992] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK <7> [303.981944] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [303.984713] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1 <7> [303.985660] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1 <7> [303.989686] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [303.990698] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4 <7> [303.992169] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [303.994160] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [303.995060] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [303.996334] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000 <7> [304.005106] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [304.006143] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A] <7> [304.011654] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [304.012740] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [304.015104] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0 <7> [304.016074] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7> [304.017113] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <6> [304.020507] Console: switching to colour frame buffer device 400x112 <6> [304.046084] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device <7> [304.061114] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [304.061142] [drm:drm_client_modeset_probe] <7> [304.061283] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] <7> [304.061311] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [304.065009] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [304.065740] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [304.066660] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [304.067486] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [304.068325] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [304.068350] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [304.068367] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [304.068440] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [304.069176] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [304.070955] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [304.071631] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [304.074519] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes : <7> [304.074543] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [304.074564] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [304.074584] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] <7> [304.074607] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [304.075829] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected <7> [304.075856] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] <7> [304.075876] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [304.076641] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected <7> [304.076661] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [304.076679] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [304.077476] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [304.077496] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [304.077511] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [304.077522] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [304.077532] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [304.077678] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [304.077721] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [304.077734] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [304.077745] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [304.078034] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [304.078099] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <7> [304.095033] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0] <7> [304.095058] [drm:drm_client_modeset_probe] <7> [304.095180] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] <7> [304.095206] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [304.100033] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [304.100809] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [304.101504] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [304.104889] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [304.105596] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [304.105618] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [304.105631] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [304.105688] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [304.106288] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [304.108947] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [304.109511] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [304.114129] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes : <7> [304.114153] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [304.114170] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [304.114186] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] <7> [304.114205] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [304.114815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected <7> [304.114837] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] <7> [304.114853] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [304.115363] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected <7> [304.115381] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] <7> [304.115397] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [304.115965] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected <7> [304.115982] [drm:drm_client_modeset_probe] connector 239 enabled? yes <7> [304.115994] [drm:drm_client_modeset_probe] connector 248 enabled? no <7> [304.116003] [drm:drm_client_modeset_probe] connector 257 enabled? no <7> [304.116011] [drm:drm_client_modeset_probe] connector 263 enabled? no <7> [304.116097] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [304.116126] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239 <7> [304.116137] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0 <7> [304.116146] [drm:drm_client_modeset_probe] found mode 3200x1800 <7> [304.116155] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config <7> [304.116190] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0) <6> [304.120382] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 <6> [304.124136] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <6> [304.135799] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [304.136254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [304.137104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [304.137728] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x810 <7> [304.154931] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [304.161126] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [304.177502] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [304.211779] [IGT] i915_module_load: finished subtest reload, SUCCESS <6> [304.212641] [IGT] i915_module_load: exiting, ret=0

<7> [301.048961] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind

<7> [301.125798] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [301.126578] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [301.127427] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [301.128275] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [301.129091] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [301.129920] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [301.130660] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [301.131486] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [301.132510] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [301.133201] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [301.134230] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4

<7> [301.138748] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)

<7> [301.139468] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 1, found 0)

<7> [301.139854] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)

<7> [301.140174] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 4, found 0)

<7> [301.140497] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0)

<7> [301.140827] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)

<7> [301.141139] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)

<7> [301.141456] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)

<7> [301.142276] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3316, found 0)

<7> [301.142631] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)

<7> [301.142999] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0)

<7> [301.143313] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)

<7> [301.143612] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)

<7> [301.143934] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)

<7> [301.144244] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1816, found 0)

<7> [301.144559] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)

<7> [301.144900] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0)

<7> [301.145209] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0)

<7> [301.145517] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0)

<7> [301.145839] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)

<7> [301.146146] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3316, found 0)

<7> [301.146447] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)

<7> [301.146742] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0)

<7> [301.147073] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)

<7> [301.147399] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)

<7> [301.147708] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)

<7> [301.148028] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0)

<7> [301.148333] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)

<7> [301.148633] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0)

<7> [301.148945] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0)

<7> [301.149254] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0)

<7> [301.149567] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)

<7> [301.149904] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)

<7> [301.150213] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)

<7> [301.150518] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)

<7> [301.150834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 361310, found 0)

<7> [301.151136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 361310, found 0)

<7> [301.151430] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)

<7> [301.151739] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [301.152083] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0

<7> [301.152458] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0

<7> [301.152870] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0

<7> [301.153163] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0

<7> [301.153446] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [301.153725] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [301.154038] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [301.154343] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [301.154644] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0

<7> [301.154972] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [301.155281] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0

<7> [301.155580] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0

<7> [301.155938] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [301.156246] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [301.156559] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [301.156909] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset]

<7> [301.157226] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [301.157528] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [301.157843] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [301.158141] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [301.158433] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [301.158737] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [301.159070] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [301.159392] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [301.178800] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [301.382215] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0

<7> [301.383263] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [301.391019] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [301.391905] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [301.393019] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off

<7> [301.393722] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [301.394493] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [301.399283] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [301.400041] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [301.400739] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [301.401840] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [301.420647] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [301.421447] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [301.422173] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20

<7> [301.422941] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [301.448120] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [301.448893] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [301.448958] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [301.449656] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [301.449721] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A]

<7> [301.450347] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30

<7> [301.450557] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [301.451359] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [301.451502] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [301.452156] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]

<7> [301.452932] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [301.453936] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [301.454669] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [301.455391] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [301.456133] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [301.456861] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [301.457558] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [301.458283] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [301.459070] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [301.459833] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [301.460568] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [301.461840] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [301.502598] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]

<7> [301.580807] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper

<7> [301.581833] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [302.054328] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [302.055182] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<6> [302.560268] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0

<4> [302.560292] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)

<4> [302.560298] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000

<7> [303.112940] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K

<7> [303.113437] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)

<7> [303.113867] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH

<7> [303.114316] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [303.114941] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [303.115328] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz

<7> [303.116315] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001

<7> [303.116634] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001

<7> [303.117465] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [303.117817] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [303.118120] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M

<6> [303.118417] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [303.119070] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [303.119107] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7

<7> [303.119455] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K

<7> [303.120222] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018

<7> [303.120631] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0

<7> [303.121005] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [303.121358] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [303.121700] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [303.129845] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583

<7> [303.130261] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [303.130604] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [303.130970] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [303.131351] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [303.131698] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no

<7> [303.132047] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [303.132361] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no

<7> [303.132652] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no

<7> [303.132956] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [303.133246] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no

<7> [303.133525] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [303.133941] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [303.134243] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [303.134534] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50

<7> [303.134937] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68

<7> [303.135331] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56

<7> [303.135715] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834

<7> [303.136178] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941

<7> [303.136548] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878

<7> [303.136933] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899

<7> [303.137301] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488

<7> [303.137687] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583

<7> [303.138097] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069

<7> [303.138467] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719

<7> [303.138849] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483

<7> [303.139208] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280

<7> [303.139562] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000

<7> [303.139962] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000

<7> [303.140350] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000

<7> [303.140709] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000

<7> [303.141089] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000

<7> [303.141453] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000

<7> [303.141814] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000

<7> [303.142173] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000

<7> [303.143846] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [303.144260] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228

<7> [303.144644] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [303.145091] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)

<7> [303.145471] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [303.145866] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [303.146225] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)

<7> [303.146585] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)

<7> [303.147216] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [303.147598] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)

<7> [303.147988] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [303.148353] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)

<7> [303.148717] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)

<7> [303.149269] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [303.149635] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [303.150014] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806

<7> [303.150467] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6

<7> [303.150865] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [303.151245] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [303.151608] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [303.151976] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [303.152332] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000

<7> [303.152678] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [303.153049] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0

<7> [303.153414] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000

<7> [303.153816] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [303.154193] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0

<7> [303.154543] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000

<7> [303.154909] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a

<7> [303.155302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [303.155714] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [303.156310] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [303.156686] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [303.157076] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [303.157443] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [303.158029] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [303.158503] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [303.159046] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [303.159411] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [303.160093] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [303.160481] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [303.160873] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [303.161282] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [303.161651] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [303.162031] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [303.162402] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [303.162772] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [303.163136] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [303.163478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [303.163850] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [303.164333] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4

<7> [303.164876] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin

<7> [303.166685] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<6> [303.167613] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)

<7> [303.167731] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us

<7> [303.168196] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [303.168556] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [303.168929] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [303.169301] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [303.169672] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [303.170059] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [303.170423] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [303.170787] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<7> [303.186686] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [303.192854] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [303.193419] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz

<7> [303.193835] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz

<7> [303.194300] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT)

<7> [303.194713] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]

<7> [303.199881] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)

<7> [303.200294] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [303.200663] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [303.201097] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless

<7> [303.201517] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [303.201932] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300

<7> [303.202304] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002

<7> [303.202692] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName

<7> [303.203078] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [303.203453] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0

<7> [303.204013] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0

<7> [303.204460] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000

<7> [303.204831] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [303.205195] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [303.205549] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [303.205938] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [303.206410] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [303.206957] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [303.207598] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [303.208024] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [303.208488] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [303.208875] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [303.209296] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [303.209651] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled

<7> [303.416069] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [303.416954] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001

<7> [303.417805] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6

<7> [303.419503] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1

<7> [303.428043] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.430050] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.432058] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.434156] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.435956] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.438520] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.440476] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.442477] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer

<7> [303.444183] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [303.444217] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [303.444237] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [303.444472] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [303.445477] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [303.446382] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)

<7> [303.455596] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none

<7> [303.456859] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)

<7> [303.458127] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000

<7> [303.459593] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000

<7> [303.460468] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [303.461325] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [303.462507] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [303.463371] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [303.464333] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [303.466523] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT)

<7> [303.467544] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]

<7> [303.469483] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [303.470453] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]

<7> [303.471336] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)

<7> [303.472903] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]

<7> [303.473724] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)

<7> [303.476345] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled

<7> [303.477553] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled

<7> [303.478727] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled

<7> [303.479666] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [303.480604] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A

<7> [303.481520] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A

<7> [303.482420] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A

<7> [303.483333] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A

<7> [303.484257] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A

<7> [303.485170] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A

<7> [303.486077] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A

<7> [303.486967] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B

<7> [303.487879] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B

<7> [303.488814] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B

<7> [303.489687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B

<7> [303.490584] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B

<7> [303.491476] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B

<7> [303.492378] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B

<7> [303.493306] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B

<7> [303.494257] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C

<7> [303.495146] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C

<7> [303.496030] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C

<7> [303.496935] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C

<7> [303.497847] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C

<7> [303.498726] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C

<7> [303.499624] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C

<7> [303.500471] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C

<7> [303.501213] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A

<7> [303.501960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [303.502621] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A

<7> [303.503314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B

<7> [303.504002] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C

<7> [303.504696] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A

<7> [303.505447] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0

<7> [303.506205] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [303.506940] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0

<7> [303.507668] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled

<7> [303.508264] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled

<7> [303.508865] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled

<7> [303.509413] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled

<7> [303.509950] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [303.510462] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz

<7> [303.510982] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz

<7> [303.511506] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz

<7> [303.512061] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz

<7> [303.512590] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz

<7> [303.513125] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz

<7> [303.513630] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz

<7> [303.514168] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [303.514657] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz

<7> [303.515092] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz

<7> [303.515491] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz

<7> [303.515904] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz

<7> [303.516290] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz

<7> [303.516687] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz

<7> [303.517122] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz

<7> [303.517535] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz

<7> [303.517956] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [303.518381] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz

<7> [303.518785] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz

<7> [303.519188] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz

<7> [303.519598] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz

<7> [303.520043] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz

<7> [303.520446] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz

<7> [303.520879] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz

<7> [303.521300] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz

<7> [303.521637] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [303.546917] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]

<7> [303.547372] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]

<7> [303.547787] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]

<7> [303.548199] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [303.548623] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [303.549049] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [303.550077] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [303.550628] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]

<7> [303.551259] MCR Steering: Default steering: group=0x0, instance=0x0

<7> [303.551306] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global

<7> [303.555557] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0

<7> [303.556258] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0

<7> [303.556805] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0

<7> [303.561232] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0

<7> [303.562557] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0

<7> [303.564594] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0

<7> [303.585631] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping

<7> [303.586074] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping

<7> [303.586442] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping

<7> [303.586820] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [303.589057] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [303.589399] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [303.589722] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [303.590087] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [303.596739] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered

<7> [303.597411] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1

<7> [303.600286] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event

<7> [303.601172] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1

<7> [303.602792] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event

<7> [303.603591] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event

<7> [303.604366] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event

<6> [303.604465] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [303.608443] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected

<6> [303.640565] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [303.648269] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input14

<7> [303.649827] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)

<6> [303.650203] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [303.651041] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4

<7> [303.651872] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]

<7> [303.651891] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [303.655598] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [303.655853] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [303.656132] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11

<7> [303.656408] i915 device info: slice0: 4 subslices, mask=0000000f

<7> [303.656230] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<6> [303.656432] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [303.656435] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [303.656608] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [303.657593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [303.658196] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [303.658212] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [303.658221] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [303.658258] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [303.658626] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [303.660355] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [303.663323] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [303.665073] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3

<7> [303.666076] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [303.667438] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to connected

<7> [303.667629] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :

<7> [303.667639] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [303.667651] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [303.668096] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]

<7> [303.668115] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [303.670573] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected

<7> [303.670607] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected

<7> [303.670622] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]

<7> [303.670638] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [303.671161] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected

<7> [303.671182] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [303.671192] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [303.671203] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [303.671620] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected

<7> [303.671639] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [303.671648] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [303.671656] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [303.671662] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [303.671668] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [303.671732] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [303.671767] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [303.671775] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [303.671781] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [303.671787] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [303.671808] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<7> [303.671846] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane

<7> [303.671969] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one

<6> [303.696350] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<7> [303.696482] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00100000

<7> [303.698961] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [303.699449] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz

<7> [303.699885] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24

<7> [303.700271] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000

<7> [303.700650] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no

<7> [303.701062] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long

<7> [303.701436] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [303.701839] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]

<7> [303.702203] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)

<7> [303.702580] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1)

<7> [303.705783] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)

<7> [303.706216] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4)

<7> [303.706595] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288)

<7> [303.707017] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)

<7> [303.707416] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)

<7> [303.707834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)

<7> [303.708215] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316)

<7> [303.708582] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)

<7> [303.708995] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316)

<7> [303.709368] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)

<7> [303.709734] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)

<7> [303.710136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)

<7> [303.710511] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816)

<7> [303.710913] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)

<7> [303.711286] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816)

<7> [303.711660] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802)

<7> [303.712056] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807)

<7> [303.712447] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)

<7> [303.712853] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316)

<7> [303.713218] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)

<7> [303.713581] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316)

<7> [303.713960] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)

<7> [303.714331] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)

<7> [303.714710] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)

<7> [303.715136] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816)

<7> [303.715516] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)

<7> [303.715901] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816)

<7> [303.716263] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802)

<7> [303.716614] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807)

<7> [303.716997] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)

<7> [303.717372] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)

<7> [303.717743] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)

<7> [303.718159] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b)

<7> [303.718525] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x00e001a5)

<7> [303.718912] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)

<7> [303.719280] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310)

<7> [303.719654] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310)

<7> [303.720071] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)

<7> [303.720459] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [303.720922] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1

<7> [303.721333] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985

<7> [303.721692] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39

<7> [303.722085] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm

<7> [303.722470] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [303.722890] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0

<7> [303.723273] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0

<7> [303.723642] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1

<7> [303.724046] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [303.724419] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446

<7> [303.724812] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446

<7> [303.725227] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz)

<7> [303.725602] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)

<7> [303.726009] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [303.726377] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz

<7> [303.726762] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1

<7> [303.727139] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0

<7> [303.727533] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0

<7> [303.727951] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]

<7> [303.728321] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [303.728690] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [303.729083] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [303.729452] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [303.729859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [303.730254] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [303.730614] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64

<7> [303.731003] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [303.731371] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [303.731729] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [303.732125] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [303.732508] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [303.732906] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [303.733297] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [303.733677] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [303.734076] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [303.734441] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310

<7> [303.734812] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0

<7> [303.735174] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [303.735562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [303.735956] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [303.736325] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [303.736692] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [303.737089] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [303.737464] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [303.737860] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [303.738239] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [303.738629] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [303.739023] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [303.739375] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [303.739782] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [303.740147] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [303.740510] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [303.740903] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [303.741279] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [303.741646] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [303.742040] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0

<7> [303.742422] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [303.742840] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [303.743208] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [303.743562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [303.743932] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [303.744292] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [303.744656] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [303.745534] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1

<7> [303.746570] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [303.747002] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [303.747383] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [303.747741] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [303.748141] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [303.748506] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [303.748898] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [303.749558] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [303.749988] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [303.750539] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]

<7> [303.750967] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [303.752592] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on

<7> [303.753255] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [303.753714] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [303.754120] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [303.754529] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on

<7> [303.754984] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b

<7> [303.965121] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [303.966212] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [303.971929] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [303.972052] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14

<7> [303.973807] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [303.974985] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [303.977381] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0

<7> [303.978247] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0

<7> [303.980992] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK

<7> [303.981944] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [303.984713] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1

<7> [303.985660] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1

<7> [303.989686] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [303.990698] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4

<7> [303.992169] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [303.994160] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [303.995060] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [303.996334] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000

<7> [304.005106] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [304.006143] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]

<7> [304.011654] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [304.012740] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [304.015104] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0

<7> [304.016074] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp

<7> [304.017113] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<6> [304.020507] Console: switching to colour frame buffer device 400x112

<6> [304.046084] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device

<7> [304.061114] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]

<7> [304.061283] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]

<7> [304.061311] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [304.065009] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [304.065740] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [304.066660] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [304.067486] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [304.068325] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [304.068350] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [304.068367] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [304.068440] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [304.069176] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [304.070955] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [304.071631] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [304.074519] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :

<7> [304.074543] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [304.074564] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [304.074584] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]

<7> [304.074607] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [304.075829] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected

<7> [304.075856] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]

<7> [304.075876] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [304.076641] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [304.076661] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [304.076679] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [304.077476] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [304.077496] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [304.077511] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [304.077522] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [304.077532] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [304.077678] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [304.077721] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [304.077734] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [304.077745] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [304.078034] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [304.078099] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<7> [304.095033] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0]

<7> [304.095180] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]

<7> [304.095206] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [304.100033] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [304.100809] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [304.101504] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [304.104889] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [304.105596] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [304.105618] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [304.105631] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [304.105688] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [304.106288] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [304.108947] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [304.109511] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [304.114129] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] probed modes :

<7> [304.114153] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [304.114170] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [304.114186] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]

<7> [304.114205] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [304.114815] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected

<7> [304.114837] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]

<7> [304.114853] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [304.115363] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [304.115381] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]

<7> [304.115397] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [304.115965] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [304.115982] [drm:drm_client_modeset_probe] connector 239 enabled? yes

<7> [304.115994] [drm:drm_client_modeset_probe] connector 248 enabled? no

<7> [304.116003] [drm:drm_client_modeset_probe] connector 257 enabled? no

<7> [304.116011] [drm:drm_client_modeset_probe] connector 263 enabled? no

<7> [304.116097] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [304.116126] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239

<7> [304.116137] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0

<7> [304.116146] [drm:drm_client_modeset_probe] found mode 3200x1800

<7> [304.116155] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config

<7> [304.116190] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)

<6> [304.120382] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100

<6> [304.124136] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)

<6> [304.135799] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [304.136254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [304.137104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [304.137728] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x810

<7> [304.161126] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<6> [304.211779] [IGT] i915_module_load: finished subtest reload, SUCCESS

Results for igt@i915_module_load@reload