Results for igt@i915_selftest@live@gtt

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g605d12880 (x86_64) (Linux: 6.6.0-rc1-linus-v6.6-rc1-g0bb80ecc33a8+ x86_64)
Out 
Starting dynamic subtest: gtt
Dynamic subtest gtt: SUCCESS (9.767s)
Err 
Starting dynamic subtest: gtt
Dynamic subtest gtt: SUCCESS (9.767s)
Dmesg
<6> [429.024447] [IGT] i915_selftest: starting dynamic subtest gtt
<5> [429.176236] Setting dangerous option live_selftests - tainting kernel
<7> [429.259632] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [429.260171] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [429.260572] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [429.260987] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [429.261623] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [429.262023] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz
<7> [429.263089] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [429.263419] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [429.264385] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [429.264728] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [429.265083] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [429.265388] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [429.265398] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [429.266181] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [429.266225] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [429.266614] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [429.267431] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [429.267875] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [429.268226] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [429.268568] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [429.268927] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [429.276868] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [429.277278] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [429.277621] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [429.277986] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [429.278372] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [429.278705] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [429.279036] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [429.279343] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [429.279639] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [429.279945] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [429.280242] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [429.280550] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [429.281020] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [429.281327] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [429.281626] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [429.282029] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [429.282407] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [429.282797] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [429.283182] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [429.283553] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [429.283936] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [429.284300] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [429.284651] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [429.285051] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [429.285437] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [429.285815] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [429.286183] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [429.286537] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [429.286903] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [429.287269] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [429.287650] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [429.288051] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [429.288417] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [429.288785] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [429.289143] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [429.290112] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [429.290529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [429.290956] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [429.291345] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [429.291753] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [429.292178] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [429.292567] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [429.292954] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [429.293330] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [429.293727] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [429.294173] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [429.294556] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [429.294954] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [429.295322] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [429.295676] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [429.296072] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [429.296474] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [429.296875] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [429.297253] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [429.297608] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [429.297987] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [429.298369] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [429.298749] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [429.299142] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [429.299509] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [429.299877] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [429.300249] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [429.300632] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [429.301086] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [429.301492] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [429.302000] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [429.302401] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [429.302809] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [429.303194] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [429.303558] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [429.303941] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [429.304424] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [429.304891] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [429.305267] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [429.305797] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [429.306163] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [429.306515] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [429.306925] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [429.307300] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [429.307659] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [429.308059] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [429.308444] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [429.308839] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [429.309203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [429.309567] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [429.310072] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [429.310596] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<7> [429.312435] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<6> [429.313451] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<7> [429.313473] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [429.313876] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [429.314238] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [429.314605] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [429.315033] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [429.315394] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [429.315736] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [429.316096] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [429.316461] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [429.337457] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [429.345744] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [429.346309] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [429.346696] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [429.347153] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] Using AUX CH A (VBT)
<7> [429.347592] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [429.353818] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [429.354206] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [429.354573] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [429.354967] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [429.355377] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [429.355762] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [429.356156] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [429.356534] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [429.356907] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [429.357277] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [429.357831] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [429.358297] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [429.358651] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [429.359015] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [429.359367] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [429.359834] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [429.360308] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [429.360843] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [429.361484] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [429.361908] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [429.362373] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [429.362735] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [429.363177] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [429.363541] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [429.568980] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [429.569846] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [429.570628] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [429.572359] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [429.580838] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.582617] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.584578] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.586418] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.588342] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.590316] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.592283] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.594249] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [429.595913] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [429.595947] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [429.595966] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [429.596198] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [429.597154] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 361310 3200 3248 3280 3680 1800 1802 1807 2045 0x40 0xa
<7> [429.598053] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)
<7> [429.608691] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [429.609948] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7> [429.610919] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000
<7> [429.612376] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [429.613256] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [429.614113] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [429.614975] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [429.615838] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [429.616762] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [429.619027] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] Using AUX CH B (VBT)
<7> [429.619983] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [429.621893] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [429.622808] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [429.623646] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [429.625164] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [429.626007] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)
<7> [429.628600] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [429.629859] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [429.631036] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<7> [429.631953] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [429.632892] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [429.633765] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [429.634673] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [429.635590] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [429.636513] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [429.637498] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [429.638396] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [429.639292] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [429.640185] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [429.641101] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [429.642006] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [429.642912] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [429.643830] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [429.644683] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [429.645604] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [429.646439] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [429.647242] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [429.648037] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [429.648826] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [429.649610] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [429.650425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [429.651227] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [429.652011] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [429.652828] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [429.653474] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [429.654106] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [429.654709] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [429.655329] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [429.655997] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [429.656638] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [429.657319] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [429.657989] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [429.658758] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [429.659423] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [429.660006] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [429.660499] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [429.661019] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [429.661526] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [429.662019] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [429.662496] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [429.662989] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [429.663458] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [429.663975] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [429.664472] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [429.664975] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [429.665482] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<7> [429.665972] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [429.666456] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [429.666933] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [429.667314] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [429.667684] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [429.668065] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [429.668432] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [429.668840] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [429.669256] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [429.669626] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [429.670015] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [429.670386] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [429.670741] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [429.671123] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [429.671514] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [429.671920] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [429.672292] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [429.695936] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [429.696365] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [429.696724] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [429.697112] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [429.697518] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [429.697925] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [429.698569] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [429.698914] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [429.699255] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [429.699281] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [429.701870] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0
<7> [429.702277] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [429.702626] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [429.705342] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [429.706971] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [429.707968] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [429.726252] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [429.726674] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [429.727058] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [429.727473] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [429.727930] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [429.729508] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [429.729880] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [429.730206] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [429.730517] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [429.739237] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [429.739895] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [429.741422] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [429.742239] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [429.743558] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [429.744377] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [429.745079] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [429.745173] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [429.749194] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [429.784698] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [429.792398] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input42
<7> [429.794729] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)
<7> [429.795915] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [429.796337] [drm:drm_client_modeset_probe]
<7> [429.796414] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<6> [429.796607] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [429.796433] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [429.796874] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] status updated from unknown to disconnected
<7> [429.796901] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] disconnected
<7> [429.797034] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:239:eDP-1] EDID changed, epoch counter 2
<7> [429.797065] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [429.797078] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [429.797450] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [429.797474] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [429.797485] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [429.797496] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [429.797874] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [429.797894] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [429.797904] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [429.797915] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [429.798271] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [429.798289] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [429.798299] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [429.798307] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [429.798314] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [429.798320] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [429.798325] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [429.798394] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [429.798416] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [429.798446] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [429.798463] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [429.799847] [drm:drm_client_modeset_probe]
<7> [429.799911] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [429.799927] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [429.800349] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] disconnected
<7> [429.800362] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [429.800373] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [429.800736] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [429.800746] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [429.800757] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [429.801162] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [429.801174] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [429.801185] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [429.801545] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [429.801555] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [429.801564] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [429.801570] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [429.801576] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [429.801582] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [429.801647] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [429.801668] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [429.801696] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [429.801713] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [429.801852] [drm:drm_client_modeset_probe]
<7> [429.801904] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1]
<7> [429.801915] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [429.802291] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:239:eDP-1] disconnected
<7> [429.802303] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1]
<7> [429.802314] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [429.802689] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:248:DP-1] disconnected
<7> [429.802700] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1]
<7> [429.802710] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [429.803095] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [429.803507] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [429.803516] i915 device info: graphics version: 11
<7> [429.803520] i915 device info: media version: 11
<7> [429.803524] i915 device info: graphics stepping: B0
<7> [429.803528] i915 device info: media stepping: B0
<7> [429.803531] i915 device info: display stepping: B0
<7> [429.803535] i915 device info: base die stepping: **
<7> [429.803538] i915 device info: gt: 0
<7> [429.803542] i915 device info: memory-regions: 0x21
<7> [429.803545] i915 device info: page-sizes: 0x211000
<7> [429.803549] i915 device info: platform: JASPERLAKE
<7> [429.803552] i915 device info: ppgtt-size: 36
<7> [429.803556] i915 device info: ppgtt-type: 2
<7> [429.803559] i915 device info: dma_mask_size: 39
<7> [429.803563] i915 device info: is_mobile: no
<7> [429.803566] i915 device info: is_lp: no
<7> [429.803570] i915 device info: require_force_probe: no
<7> [429.803574] i915 device info: is_dgfx: no
<7> [429.803577] i915 device info: has_64bit_reloc: yes
<7> [429.803581] i915 device info: has_64k_pages: no
<7> [429.803584] i915 device info: gpu_reset_clobbers_display: no
<7> [429.803587] i915 device info: has_reset_engine: yes
<7> [429.803591] i915 device info: has_3d_pipeline: yes
<7> [429.803594] i915 device info: has_4tile: no
<7> [429.803598] i915 device info: has_flat_ccs: no
<7> [429.803601] i915 device info: has_global_mocs: no
<7> [429.803605] i915 device info: has_gmd_id: no
<7> [429.803608] i915 device info: has_gt_uc: yes
<7> [429.803611] i915 device info: has_heci_pxp: no
<7> [429.803615] i915 device info: has_heci_gscfi: no
<7> [429.803618] i915 device info: has_guc_deprivilege: no
<7> [429.803621] i915 device info: has_l3_ccs_read: no
<7> [429.803625] i915 device info: has_l3_dpf: no
<7> [429.803628] i915 device info: has_llc: yes
<7> [429.803632] i915 device info: has_logical_ring_contexts: yes
<7> [429.803635] i915 device info: has_logical_ring_elsq: yes
<7> [429.803639] i915 device info: has_media_ratio_mode: no
<7> [429.803642] i915 device info: has_mslice_steering: no
<7> [429.803646] i915 device info: has_oa_bpc_reporting: no
<7> [429.803649] i915 device info: has_oa_slice_contrib_limits: no
<7> [429.803652] i915 device info: has_oam: no
<7> [429.803656] i915 device info: has_one_eu_per_fuse_bit: no
<7> [429.803659] i915 device info: has_pxp: no
<7> [429.803662] i915 device info: has_rc6: yes
<7> [429.803666] i915 device info: has_rc6p: no
<7> [429.803669] i915 device info: has_rps: yes
<7> [429.803672] i915 device info: has_runtime_pm: yes
<7> [429.803676] i915 device info: has_snoop: no
<7> [429.803679] i915 device info: has_coherent_ggtt: no
<7> [429.803683] i915 device info: tuning_thread_rr_after_dep: no
<7> [429.803686] i915 device info: unfenced_needs_alignment: no
<7> [429.803690] i915 device info: hws_needs_physical: no
<7> [429.803693] i915 device info: has_pooled_eu: no
<7> [429.803696] i915 device info: rawclk rate: 19200 kHz
<7> [429.803701] i915 device info: display version: 11
<7> [429.803704] i915 device info: cursor_needs_physical: no
<7> [429.803708] i915 device info: has_cdclk_crawl: no
<7> [429.803711] i915 device info: has_cdclk_squash: no
<7> [429.803715] i915 device info: has_ddi: yes
<7> [429.803718] i915 device info: has_dp_mst: yes
<7> [429.803721] i915 device info: has_dsb: no
<7> [429.803724] i915 device info: has_fpga_dbg: yes
<7> [429.803728] i915 device info: has_gmch: no
<7> [429.803731] i915 device info: has_hotplug: yes
<7> [429.803735] i915 device info: has_hti: no
<7> [429.803738] i915 device info: has_ipc: yes
<7> [429.803741] i915 device info: has_overlay: no
<7> [429.803745] i915 device info: has_psr: yes
<7> [429.803748] i915 device info: has_psr_hw_tracking: yes
<7> [429.803751] i915 device info: overlay_needs_physical: no
<7> [429.803755] i915 device info: supports_tv: no
<7> [429.803758] i915 device info: has_hdcp: no
<7> [429.803761] i915 device info: has_dmc: yes
<7> [429.803765] i915 device info: has_dsc: yes
<7> [429.803798] i915 device info: iommu: enabled
<7> [429.803803] i915 device info: available engines: 40403
<7> [429.803808] i915 device info: slice total: 1, mask=0001
<7> [429.803812] i915 device info: subslice total: 4
<7> [429.803815] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [429.803820] i915 device info: EU total: 16
<7> [429.803823] i915 device info: EU per subslice: 4
<7> [429.803827] i915 device info: has slice power gating: yes
<7> [429.803830] i915 device info: has subslice power gating: yes
<7> [429.803834] i915 device info: has EU power gating: yes
<6> [429.803838] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [429.803842] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [429.803846] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<6> [429.803854] i915: Performing live selftests with st_random_seed=0x140b7e63 st_timeout=500
<6> [429.803859] i915: Running gtt
<6> [429.803898] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_alloc
<7> [429.806008] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [429.806029] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2]
<7> [429.806041] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [429.806573] [drm:drm_helper_probe_single_connector_modes] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [429.806585] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [429.806594] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [429.806601] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [429.806607] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [429.806613] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [429.806676] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [429.806698] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [429.806725] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock] test CRTC 0 primary plane
<6> [429.806744] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [429.841822] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [429.842749] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<6> [431.047909] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_lowlevel
<7> [431.047946] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [431.548834] lowlevel_hole timed out before 1179/524288
<6> [431.581316] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_drunk
<7> [431.581354] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [432.081963] drunk_hole timed out after 843/524288
<6> [432.090048] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_walk
<7> [432.090078] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [432.591272] walk_hole timed out at 370000
<6> [432.602173] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_pot
<7> [432.602203] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [432.650057] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [432.650564] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [432.651001] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [432.651701] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [432.652287] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [432.652659] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [432.652957] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [432.653344] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [432.653744] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [432.654308] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [432.655278] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [433.194050] pot_hole timed out after 27/35
<6> [433.206884] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_fill
<7> [433.206913] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [433.841742] fill_hole timed out (npages=131072, prime=2)
<6> [433.853764] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_shrink
<7> [433.853816] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [434.543348] __shrink_hole timed out at ofset 1fffff000 [0 - 1000000000]
<6> [434.594505] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_shrink_boom
<7> [434.594541] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [434.754868] i915: Running i915_gem_gtt_live_selftests/igt_ppgtt_misaligned_pin
<7> [434.754904] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [434.804106] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_lowlevel
<7> [435.304798] lowlevel_hole timed out before 20695/524204
<7> [435.780069] lowlevel_hole timed out before 0/1
<6> [435.787091] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_drunk
<7> [436.287824] drunk_hole timed out after 4091/524204
<6> [436.294210] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_walk
<7> [436.794846] walk_hole timed out at 10d8000
<6> [436.801322] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_pot
<7> [437.776613] pot_hole timed out after 20/31
<6> [437.791215] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_fill
<7> [438.314374] fill_hole timed out (npages=131072, prime=2)
<6> [438.323240] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_page
<6> [438.343221] i915: Running i915_gem_gtt_live_selftests/igt_ggtt_misaligned_pin
<7> [438.378267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [438.379290] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [438.380569] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [438.381940] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [438.382884] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [438.383754] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [438.384691] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [438.385650] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [438.386611] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [438.387293] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [438.387948] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [438.388592] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [438.419416] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [438.460916] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [438.461402] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [438.462002] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [438.462420] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<4> [438.508516] i915: probe of 0000:00:02.0 failed with error -25
<6> [438.793273] [IGT] i915_selftest: finished subtest gtt, SUCCESS
Created at 2023-09-11 01:21:38