Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-g34b68fb58 (x86_64) (Linux: 6.5.0-linus-v6.5-g2dde18cd1d8f+ x86_64) |
| Out |
Starting subtest: basic-s2idle-without-i915 Opened device: /dev/dri/card0 [cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Sun Aug 27 22:26:14 2023 Subtest basic-s2idle-without-i915: SUCCESS (4.285s) |
| Err |
Starting subtest: basic-s2idle-without-i915 Subtest basic-s2idle-without-i915: SUCCESS (4.285s) |
| Dmesg |
<6> [461.867893] [IGT] i915_suspend: executing
<6> [461.871766] [IGT] i915_suspend: starting subtest basic-s2idle-without-i915
<7> [462.113956] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [462.114233] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [462.114432] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [462.114611] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [462.114970] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [462.115214] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [462.116221] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [462.116382] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [462.116521] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [462.116660] i915 0000:00:02.0: vgaarb: deactivate vga console
<7> [462.116978] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [462.117157] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [462.117582] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018
<7> [462.117850] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [462.118068] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [462.118249] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [462.118428] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [462.124838] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [462.125059] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [462.125261] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [462.125461] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [462.125663] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: LPDDR3
<7> [462.125880] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [462.126112] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [462.126339] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [462.126563] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [462.126804] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [462.127034] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [462.127265] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [462.127491] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [462.127715] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [462.128514] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [462.128764] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203
<7> [462.129047] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [462.129323] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [462.129547] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [462.129768] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [462.130030] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [462.130303] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [462.130524] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [462.130806] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [462.131101] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [462.131323] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [462.131539] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [462.131865] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [462.132174] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [462.132488] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [462.132819] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [462.133142] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [462.133381] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [462.133596] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [462.133832] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [462.134102] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [462.134317] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [462.134531] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [462.134745] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [462.135007] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [462.135362] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [462.135607] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [462.135863] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [462.136144] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [462.136359] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Max dotclock rate: 675000 kHz
<7> [462.136575] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [462.136917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [462.137210] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [462.137520] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [462.137867] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [462.138267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [462.138585] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [462.138845] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [462.139083] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [462.139342] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin
<7> [462.140627] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<6> [462.140940] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)
<7> [462.141284] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [462.141556] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [462.141765] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [462.142029] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [462.142246] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [462.142448] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [462.142649] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [462.142881] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [462.143099] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [462.143301] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [462.148794] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [462.153972] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [462.154358] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] using AUX A (VBT)
<7> [462.154676] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [462.159197] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [462.159516] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [462.160046] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [462.160366] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [462.160692] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [462.161140] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [462.161360] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP
<7> [462.161575] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [462.161807] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0
<7> [462.162048] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0
<7> [462.162463] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [462.162843] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [462.163134] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [462.163428] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [462.163686] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [462.164115] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [462.164362] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [462.164984] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [462.165290] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [462.165638] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [462.166009] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [462.166338] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [462.166611] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [462.377026] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [462.378475] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [462.380038] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40
<7> [462.382457] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [462.402292] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [462.402348] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [462.402384] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [462.402770] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [462.404110] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [462.405635] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:95:eDP-1] DRRS type: static
<7> [462.407149] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:95:eDP-1] Using native PCH PWM for backlight control
<7> [462.408038] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:95:eDP-1] backlight initialized, disabled, brightness 0/937
<7> [462.409016] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [462.409755] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [462.410522] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [462.411463] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [462.412107] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [462.412583] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [462.413835] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DDI B/PHY B] using AUX B (VBT)
<7> [462.414340] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DDI B/PHY B]
<7> [462.415658] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [462.416179] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:102:DDI B/PHY B]
<7> [462.416713] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:102:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [462.417595] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:117:DDI C/PHY C] using AUX C (VBT)
<7> [462.418040] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:117:DDI C/PHY C]
<7> [462.418826] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [462.419223] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:117:DDI C/PHY C]
<7> [462.419544] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:117:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [462.420119] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present
<7> [462.420477] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port E is not present
<7> [462.421409] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [462.421976] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [462.422337] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [462.422655] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [462.422999] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [462.423310] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [462.423600] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [462.423936] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [462.424245] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [462.424535] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [462.424860] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [462.425182] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [462.425601] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [462.425959] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [462.426274] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DP-MST A] hw state readout: disabled, pipe A
<7> [462.426550] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:105:DP-MST B] hw state readout: disabled, pipe B
<7> [462.426851] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP-MST C] hw state readout: disabled, pipe C
<7> [462.427118] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [462.427349] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
<7> [462.427579] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
<7> [462.427835] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
<7> [462.428103] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [462.428354] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [462.428602] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [462.428883] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [462.429260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:eDP-1] hw state readout: disabled
<7> [462.429520] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [462.429774] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:112:HDMI-A-1] hw state readout: disabled
<7> [462.430067] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
<7> [462.430336] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:124:HDMI-A-2] hw state readout: disabled
<7> [462.430663] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [462.431026] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [462.431355] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [462.431688] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [462.432043] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [462.432290] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [462.432499] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [462.432705] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [462.432952] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [462.433208] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [462.433415] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [462.433622] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [462.434001] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [462.434238] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [462.434454] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [462.434667] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [462.434908] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [462.435205] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [462.435413] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [462.435678] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [462.435867] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [462.436082] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [462.436291] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 GT workarounds on global
<7> [462.438390] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [462.438621] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [462.438937] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 context workarounds on rcs'0
<7> [462.457181] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [462.457587] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [462.457869] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [462.458164] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [462.458453] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [462.458810] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [462.459696] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [462.459891] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [462.460047] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [462.460244] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [462.470055] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:95:eDP-1] backlight device intel_backlight registered
<7> [462.470555] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [462.472397] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:eDP-1] generating connector hotplug event
<7> [462.473295] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [462.474733] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<7> [462.475609] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:112:HDMI-A-1] generating connector hotplug event
<7> [462.476461] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [462.477851] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:118:DP-2] generating connector hotplug event
<7> [462.478673] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:124:HDMI-A-2] generating connector hotplug event
<6> [462.479049] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [462.482775] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected
<6> [462.509433] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [462.521617] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input72
<7> [462.523163] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [462.524202] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [462.524551] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [462.525109] [drm:drm_client_modeset_probe]
<7> [462.525686] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [462.525762] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [462.527760] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [462.528116] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [462.530008] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [462.530325] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [462.530616] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [462.530922] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [462.531351] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [462.531366] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [462.531376] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [462.531442] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [462.531738] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [462.532426] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [462.532739] i915 device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9
<7> [462.532747] i915 device info: graphics version: 9
<7> [462.532751] i915 device info: media version: 9
<7> [462.532756] i915 device info: display version: 9
<7> [462.532760] i915 device info: graphics stepping: H0
<7> [462.532765] i915 device info: media stepping: H0
<7> [462.532769] i915 device info: display stepping: H0
<7> [462.532774] i915 device info: base die stepping: **
<7> [462.532794] i915 device info: gt: 2
<7> [462.532798] i915 device info: memory-regions: 0x21
<7> [462.532803] i915 device info: page-sizes: 0x11000
<7> [462.532807] i915 device info: platform: SKYLAKE
<7> [462.532812] i915 device info: ppgtt-size: 48
<7> [462.532817] i915 device info: ppgtt-type: 2
<7> [462.532821] i915 device info: dma_mask_size: 39
<7> [462.532825] i915 device info: is_mobile: no
<7> [462.532830] i915 device info: is_lp: no
<7> [462.532834] i915 device info: require_force_probe: no
<7> [462.532839] i915 device info: is_dgfx: no
<7> [462.532843] i915 device info: has_64bit_reloc: yes
<7> [462.532847] i915 device info: has_64k_pages: no
<7> [462.532852] i915 device info: gpu_reset_clobbers_display: no
<7> [462.532856] i915 device info: has_reset_engine: yes
<7> [462.532861] i915 device info: has_3d_pipeline: yes
<7> [462.532865] i915 device info: has_4tile: no
<7> [462.532870] i915 device info: has_flat_ccs: no
<7> [462.532874] i915 device info: has_global_mocs: no
<7> [462.532878] i915 device info: has_gmd_id: no
<7> [462.532883] i915 device info: has_gt_uc: yes
<7> [462.532887] i915 device info: has_heci_pxp: no
<7> [462.532892] i915 device info: has_heci_gscfi: no
<7> [462.532896] i915 device info: has_guc_deprivilege: no
<7> [462.532901] i915 device info: has_l3_ccs_read: no
<7> [462.532905] i915 device info: has_l3_dpf: no
<7> [462.532909] i915 device info: has_llc: yes
<7> [462.532914] i915 device info: has_logical_ring_contexts: yes
<7> [462.532918] i915 device info: has_logical_ring_elsq: no
<7> [462.532923] i915 device info: has_media_ratio_mode: no
<7> [462.532927] i915 device info: has_mslice_steering: no
<7> [462.532932] i915 device info: has_oa_bpc_reporting: no
<7> [462.532936] i915 device info: has_oa_slice_contrib_limits: no
<7> [462.532941] i915 device info: has_oam: no
<7> [462.532945] i915 device info: has_one_eu_per_fuse_bit: no
<7> [462.532949] i915 device info: has_pxp: no
<7> [462.532953] i915 device info: has_rc6: yes
<7> [462.532957] i915 device info: has_rc6p: no
<7> [462.532962] i915 device info: has_rps: yes
<7> [462.532966] i915 device info: has_runtime_pm: yes
<7> [462.532970] i915 device info: has_snoop: no
<7> [462.532974] i915 device info: has_coherent_ggtt: yes
<7> [462.532979] i915 device info: tuning_thread_rr_after_dep: no
<7> [462.532983] i915 device info: unfenced_needs_alignment: no
<7> [462.532987] i915 device info: hws_needs_physical: no
<7> [462.532991] i915 device info: has_pooled_eu: no
<7> [462.532995] i915 device info: cursor_needs_physical: no
<7> [462.533000] i915 device info: has_cdclk_crawl: no
<7> [462.533004] i915 device info: has_cdclk_squash: no
<7> [462.533008] i915 device info: has_ddi: yes
<7> [462.533012] i915 device info: has_dp_mst: yes
<7> [462.533016] i915 device info: has_dsb: no
<7> [462.533021] i915 device info: has_fpga_dbg: yes
<7> [462.533025] i915 device info: has_gmch: no
<7> [462.533029] i915 device info: has_hotplug: yes
<7> [462.533033] i915 device info: has_hti: no
<7> [462.533037] i915 device info: has_ipc: yes
<7> [462.533042] i915 device info: has_overlay: no
<7> [462.533046] i915 device info: has_psr: yes
<7> [462.533050] i915 device info: has_psr_hw_tracking: yes
<7> [462.533054] i915 device info: overlay_needs_physical: no
<7> [462.533058] i915 device info: supports_tv: no
<7> [462.533063] i915 device info: has_hdcp: yes
<7> [462.533067] i915 device info: has_dmc: yes
<7> [462.533071] i915 device info: has_dsc: no
<7> [462.533075] i915 device info: rawclk rate: 24000 kHz
<7> [462.533080] i915 device info: iommu: disabled
<7> [462.533084] i915 device info: available engines: 40403
<7> [462.533089] i915 device info: slice total: 1, mask=0001
<7> [462.533094] i915 device info: subslice total: 3
<7> [462.533098] i915 device info: slice0: 3 subslices, mask=00000007
<7> [462.533103] i915 device info: slice1: 0 subslices, mask=00000000
<7> [462.533108] i915 device info: slice2: 0 subslices, mask=00000000
<7> [462.533113] i915 device info: EU total: 24
<7> [462.533117] i915 device info: EU per subslice: 8
<7> [462.533121] i915 device info: has slice power gating: no
<7> [462.533125] i915 device info: has subslice power gating: no
<7> [462.533130] i915 device info: has EU power gating: yes
<6> [462.533134] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [462.533139] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [462.533144] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [462.534066] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [462.534376] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [462.539243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [462.540223] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] status updated from unknown to connected
<7> [462.540813] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [462.540849] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [462.540863] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [462.540875] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [462.540906] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [462.541386] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] status updated from unknown to disconnected
<7> [462.541428] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [462.541456] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1]
<7> [462.541484] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [462.542658] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [462.543005] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [462.543505] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [462.543868] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [462.543880] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [462.544167] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [462.549573] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [462.549589] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [462.550054] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] status updated from unknown to disconnected
<7> [462.550101] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [462.550129] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2]
<7> [462.550158] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [462.550516] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] status updated from unknown to disconnected
<7> [462.550561] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] disconnected
<7> [462.550590] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2]
<7> [462.550618] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [462.551688] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [462.552087] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [462.554314] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [462.554643] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [462.554656] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [462.554982] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [462.558540] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [462.558554] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [462.558908] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] status updated from unknown to disconnected
<7> [462.558957] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [462.558986] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [462.558995] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [462.559002] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [462.559009] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [462.559015] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [462.559317] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [462.559356] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [462.559365] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [462.559372] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [462.559379] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [462.559401] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [462.559559] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<7> [462.559679] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [462.565389] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x000c0000
<6> [462.566437] fbcon: i915drmfb (fb0) is primary device
<6> [462.567256] Console: switching to colour frame buffer device 400x112
<6> [462.567278] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [462.579002] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [462.579043] [drm:drm_client_modeset_probe]
<7> [462.579581] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [462.579657] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [462.581177] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [462.581448] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [462.581692] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [462.581953] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [462.582403] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [462.582418] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [462.582428] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [462.582486] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [462.582739] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [462.583848] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [462.584103] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [462.585142] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [462.585184] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [462.585198] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [462.585210] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [462.585242] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [462.586002] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [462.586037] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1]
<7> [462.586067] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [462.587101] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [462.587362] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [462.588579] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [462.588871] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [462.588884] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [462.589125] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [462.597413] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [462.597430] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [462.597710] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [462.597745] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2]
<7> [462.597776] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [462.598374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] disconnected
<7> [462.598408] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2]
<7> [462.598437] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [462.599103] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [462.599351] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [462.600062] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [462.600331] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [462.600342] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [462.600581] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [462.606677] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [462.606692] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [462.607196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [462.607232] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [462.607242] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [462.607249] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [462.607256] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [462.607263] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [462.607558] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [462.607599] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [462.607608] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [462.607615] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [462.607622] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [462.607671] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [462.609254] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:95:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [462.609582] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 373250KHz
<6> [462.611164] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [462.611850] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [462.612115] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1119750 available 2160000
<7> [462.612368] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:95:eDP-1] SDP split enable: no
<7> [462.612615] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:51:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [462.612964] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:94:DDI A/PHY A] [CRTC:51:pipe A]
<7> [462.613215] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [462.613479] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [462.613740] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [462.614089] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [462.614363] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
<7> [462.614636] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [462.614988] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [462.615259] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [462.615527] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
<7> [462.626809] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [462.627111] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
<7> [462.627382] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [462.627650] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [462.628183] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [462.628457] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
<7> [462.628725] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [462.631961] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
<7> [462.632250] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [462.632521] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
<7> [462.633024] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [462.633301] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
<7> [462.633569] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [462.634087] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
<7> [462.634359] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [462.634627] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [462.635138] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [462.635411] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
<7> [462.635679] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [462.636110] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
<7> [462.636385] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [462.636653] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
<7> [462.639649] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [462.640142] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [462.640416] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [462.640687] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000001)
<7> [462.641146] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [462.641419] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
<7> [462.641686] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
<7> [462.644442] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [462.644736] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [462.645275] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
<7> [462.645581] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 856), size 0 -> 856
<7> [462.646070] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36
<7> [462.646322] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
<7> [462.646573] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [462.647074] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0
<7> [462.647331] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0
<7> [462.647635] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (373250 kHz) > [CRTC:51:pipe A] min cdclk (0 kHz)
<7> [462.648318] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
<7> [462.648600] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [462.649047] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
<7> [462.649317] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [462.649590] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:51:pipe A] allocated DPLL 0
<7> [462.650042] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:51:pipe A] reserving DPLL 0
<7> [462.650314] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: yes [modeset]
<7> [462.650583] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [462.651187] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [462.651461] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [462.651726] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [462.652106] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [462.652374] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [462.652640] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
<7> [462.652981] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [462.653248] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [462.653515] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [462.653883] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0
<7> [462.653891] i915 0000:00:02.0: pixelformat: RGB
<7> [462.653898] i915 0000:00:02.0: colorimetry: sRGB
<7> [462.653904] i915 0000:00:02.0: bpc: 0
<7> [462.653910] i915 0000:00:02.0: dynamic range: VESA range
<7> [462.653915] i915 0000:00:02.0: content type: Not defined
<7> [462.653922] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [462.654190] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [462.654460] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [462.654731] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [462.655110] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [462.655382] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [462.655651] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
<7> [462.656003] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
<7> [462.656269] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [462.656536] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [462.656883] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [462.657152] i915 0000:00:02.0: [drm:skl_dump_hw_state [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
<7> [462.657418] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [462.657688] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [462.658042] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [462.658310] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [462.658571] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [462.660093] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [462.660376] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [462.660654] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:96] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [462.661137] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [462.661227] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [462.661406] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [462.661680] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [462.661979] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [462.663296] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
<7> [462.664488] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [462.664764] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [462.665254] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [462.665514] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [462.665769] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [462.666212] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [462.666470] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [462.666727] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [462.667169] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [462.667430] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [462.668014] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [462.668302] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [462.668582] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [462.669245] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:51:pipe A]
<7> [462.669533] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [462.670275] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power on
<7> [462.670631] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [462.671165] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [462.671418] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [462.671681] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power on
<7> [462.672198] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000000b
<7> [462.872813] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [462.873089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [462.873594] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [462.875763] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [462.876809] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [462.877679] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [462.877947] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [462.878177] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [462.879508] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Clock recovery OK
<7> [462.879732] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
<7> [462.879970] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS2
<7> [462.881902] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [462.882127] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [462.882358] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [462.884603] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [462.884872] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [462.885472] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [462.886008] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [462.886234] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [462.886611] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 937
<7> [462.887089] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, limit: 1
<7> [462.887351] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [462.902877] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
<7> [462.904583] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [462.904918] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [462.905352] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [462.905660] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<6> [462.906923] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [462.907211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [462.907807] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [462.908745] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [462.908809] [drm:drm_client_modeset_probe]
<7> [462.908900] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [462.908933] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [462.910537] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [462.910862] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [462.911096] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [462.911323] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [462.911603] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [462.911616] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [462.911626] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [462.912059] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [462.912300] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [462.915883] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [462.916170] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [462.917302] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [462.917334] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [462.917348] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [462.917362] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [462.917395] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [462.917706] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [462.917738] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1]
<7> [462.917770] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [462.918361] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [462.918618] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [462.919548] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [462.919868] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [462.919880] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [462.920129] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [462.927072] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [462.927085] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [462.927406] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [462.927482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2]
<7> [462.927563] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [462.928000] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] disconnected
<7> [462.928084] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2]
<7> [462.928155] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [462.928984] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [462.929283] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [462.930042] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [462.930392] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [462.930404] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [462.930702] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [462.938252] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [462.938268] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [462.938539] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [462.938573] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [462.938583] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [462.938590] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [462.938597] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [462.938604] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [462.938681] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [462.938701] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [462.938710] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [462.938717] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [462.938724] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [462.938757] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<6> [462.967759] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
<6> [462.967801] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [462.967808] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [462.967814] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [462.967820] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [462.967825] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19
<6> [462.967831] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a
<6> [462.967836] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
<6> [462.971102] [IGT] Unloading i915
<6> [462.973111] Console: switching to colour dummy device 80x25
<7> [463.038089] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [463.038409] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [463.038672] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [463.038959] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [463.039235] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [463.039496] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [463.039755] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [463.040045] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [463.040308] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [463.054436] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input73
<6> [463.058002] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input74
<6> [463.059021] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input75
<6> [463.060087] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input76
<7> [463.183167] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [463.276908] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [463.277312] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [463.277500] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [463.277677] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [463.279026] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)
<7> [463.279318] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 1, found 0)
<7> [463.279580] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)
<7> [463.279876] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [463.280139] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4348677/8388608 link 362389/524288, found tu 0, data 0/0 link 0/0)
<7> [463.280399] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [463.280658] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [463.280920] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)
<7> [463.281172] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3360, found 0)
<7> [463.281434] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)
<7> [463.281690] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3360, found 0)
<7> [463.282150] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)
<7> [463.282563] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)
<7> [463.282964] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [463.283169] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1852, found 0)
<7> [463.283358] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [463.283534] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1852, found 0)
<7> [463.283709] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1803, found 0)
<7> [463.283958] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1808, found 0)
<7> [463.284211] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)
<7> [463.284459] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3360, found 0)
<7> [463.284637] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)
<7> [463.284881] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3360, found 0)
<7> [463.285121] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)
<7> [463.285328] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)
<7> [463.285505] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [463.285684] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1852, found 0)
<7> [463.285891] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [463.286091] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1852, found 0)
<7> [463.286303] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1803, found 0)
<7> [463.286557] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1808, found 0)
<7> [463.286848] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<7> [463.287111] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [463.287373] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [463.287642] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [463.288410] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 373250, found 0)
<7> [463.288599] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 373250, found 0)
<7> [463.288805] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [463.289055] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [463.289241] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:51:pipe A] releasing DPLL 0
<7> [463.289520] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 892) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [463.289875] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 856) -> ( 0 - 0), size 856 -> 0
<7> [463.290134] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 856 - 892) -> ( 0 - 0), size 36 -> 0
<7> [463.290381] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [463.290631] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [463.290912] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [463.291160] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [463.291428] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [463.291613] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 337500 kHz, actual 337500 kHz
<7> [463.291820] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
<7> [463.292060] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [modeset]
<7> [463.292232] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
<7> [463.292469] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [463.292719] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [463.293204] i915 0000:00:02.0: [drm:intel_psr_disable_locked [i915]] Disabling PSR1
<7> [463.294761] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<7> [463.501842] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 0
<7> [463.502281] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [463.503631] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power off
<7> [463.503903] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [463.504161] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x01000000, dig 0x11001010, pins 0x00000010, long 0x00000000
<7> [463.504317] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:94:DDI A/PHY A] - short
<7> [463.504518] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000000
<7> [463.555833] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [463.556086] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x01000000, dig 0x12001010, pins 0x00000010, long 0x00000010
<7> [463.556255] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:94:DDI A/PHY A] - long
<7> [463.556423] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [463.556825] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring short hpd on eDP [ENCODER:94:DDI A/PHY A]
<7> [463.557034] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:51:pipe A]
<7> [463.557067] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:94:DDI A/PHY A]
<7> [463.557344] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
<7> [463.557579] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [463.557932] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [463.558699] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [463.558925] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [463.559135] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [463.559290] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [463.559461] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [463.559614] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [463.559766] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [463.559945] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [463.560161] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [463.560314] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [463.560484] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [463.560653] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [463.560843] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [463.561051] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [463.561285] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [463.581552] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [463.650841] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [463.651635] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [464.206433] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [464.207441] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<6> [464.848834] PM: suspend entry (s2idle)
<6> [464.853486] Filesystems sync: 0.004 seconds
<6> [464.859910] Freezing user space processes
<6> [464.864218] Freezing user space processes completed (elapsed 0.004 seconds)
<6> [464.864288] OOM killer disabled.
<6> [464.864294] Freezing remaining freezable tasks
<6> [464.866137] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<6> [464.885714] asix 1-1:1.0 enx00106031d5f9: Link is Down
<7> [464.910351] PM: suspend of devices complete after 29.866 msecs
<7> [464.910361] PM: start suspend of devices complete after 44.113 msecs
<7> [464.914421] PM: late suspend of devices complete after 4.054 msecs
<6> [464.937739] ACPI: EC: interrupt blocked
<7> [464.965244] PM: noirq suspend of devices complete after 34.579 msecs
<6> [464.966583] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off
<6> [464.968026] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry
<7> [464.968035] PM: suspend-to-idle
<7> [480.525015] Timekeeping suspended for 15.232 seconds
<7> [480.527935] PM: Triggering wakeup from IRQ 9
<7> [480.529235] ACPI: PM: ACPI fixed event wakeup
<7> [480.529277] PM: resume from suspend-to-idle
<6> [480.534943] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit
<6> [480.536250] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on
<6> [480.537738] ACPI: EC: interrupt unblocked
<7> [480.554341] PM: noirq resume of devices complete after 18.081 msecs
<7> [480.574894] PM: early resume of devices complete after 2.671 msecs
<6> [480.882173] asix 1-1:1.0 enx00106031d5f9: configuring for phy/internal link mode
<7> [480.891397] PM: resume of devices complete after 316.493 msecs
<6> [480.907017] OOM killer enabled.
<6> [480.907050] Restarting tasks ... done.
<5> [480.942987] random: crng reseeded on system resumption
<6> [480.954088] PM: suspend exit
<6> [480.959800] [IGT] Re-loading i915
<7> [481.227893] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K
<7> [481.228201] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [481.228409] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint LP PCH
<7> [481.228689] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [481.229108] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [481.229357] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz
<7> [481.230438] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [481.230690] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [481.230917] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [481.231163] i915 0000:00:02.0: vgaarb: deactivate vga console
<7> [481.231551] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 7ff00047
<7> [481.231815] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K
<7> [481.232485] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x79ec6018
<7> [481.232812] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [481.233091] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [481.233388] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [481.233693] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [481.242166] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483
<7> [481.242414] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [481.242654] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [481.242918] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [481.243117] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: LPDDR3
<7> [481.243263] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [481.243402] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [481.243551] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [481.243770] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X16, ranks: 2, 16Gb DIMMs: no
<7> [481.243919] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [481.244056] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [481.244189] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [481.244322] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [481.244540] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [481.245301] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [481.245588] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 203
<7> [481.245900] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [481.246207] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)
<7> [481.246530] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [481.246838] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [481.247137] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)
<7> [481.247353] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)
<7> [481.247586] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [481.247860] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)
<7> [481.248125] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [481.248429] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [481.248741] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0
<7> [481.249036] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [481.249333] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [481.249594] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [481.249853] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [481.250081] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [481.250309] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [481.250542] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [481.250769] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [481.250976] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 8
<7> [481.251181] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [481.251385] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8
<7> [481.251655] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02
<7> [481.251934] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [481.252240] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [481.252505] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO
<7> [481.252735] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [481.252948] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz
<7> [481.253155] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Max dotclock rate: 675000 kHz
<7> [481.253394] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [481.253823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [481.254118] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [481.254412] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [481.254751] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [481.255052] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [481.255263] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B
<7> [481.255490] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C
<7> [481.255699] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D
<7> [481.256019] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/skl_dmc_ver1_27.bin
<6> [481.257781] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/skl_dmc_ver1_27.bin (v1.27)
<7> [481.257805] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [481.258464] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV
<7> [481.258843] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us
<7> [481.259130] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [481.259416] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [481.259728] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [481.260014] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [481.260266] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [481.260499] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [481.260732] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [481.260928] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [481.263492] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [481.265862] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0
<7> [481.266220] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI A/PHY A] using AUX A (VBT)
<7> [481.266538] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:94:DDI A/PHY A]
<7> [481.269999] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [481.270278] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [481.270706] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [481.271006] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [481.271318] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [481.271995] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [481.272210] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: HD eDP
<7> [481.272417] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [481.272643] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 10, level 255, controller 0
<7> [481.273051] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:0
<7> [481.273668] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:94:DDI A/PHY A] initial power sequencer: PPS 0
<7> [481.274015] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [481.274279] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [481.274489] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [481.274782] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [481.274971] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [481.275214] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [481.276499] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turning VDD on
<7> [481.276797] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [481.277165] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000000
<7> [481.277365] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [481.277619] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [481.277950] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [481.485808] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [481.488158] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000
<7> [481.489691] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 9f 40
<7> [481.492826] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [481.512155] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [481.512228] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [481.512278] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [481.512976] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [481.514714] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:95:eDP-1] using alternate EDID fixed mode: "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [481.515608] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:95:eDP-1] DRRS type: static
<7> [481.516809] i915 0000:00:02.0: [drm:lpt_setup_backlight [i915]] [CONNECTOR:95:eDP-1] Using native PCH PWM for backlight control
<7> [481.517857] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:95:eDP-1] backlight initialized, disabled, brightness 0/937
<7> [481.519199] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [481.520157] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [481.520819] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [481.521385] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [481.522062] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [481.522724] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x4af06
<7> [481.524098] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:102:DDI B/PHY B] using AUX B (VBT)
<7> [481.524633] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:102:DDI B/PHY B]
<7> [481.525780] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [481.526136] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:102:DDI B/PHY B]
<7> [481.526545] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:102:DDI B/PHY B] Using DDC pin 0x5 (VBT)
<7> [481.527286] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:117:DDI C/PHY C] using AUX C (VBT)
<7> [481.527729] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:117:DDI C/PHY C]
<7> [481.528885] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [481.529395] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:117:DDI C/PHY C]
<7> [481.529886] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:117:DDI C/PHY C] Using DDC pin 0x4 (VBT)
<7> [481.530478] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present
<7> [481.530838] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port E is not present
<7> [481.531629] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled
<7> [481.532124] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled
<7> [481.532633] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled
<7> [481.533053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [481.533386] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A
<7> [481.533720] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A
<7> [481.534069] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B
<7> [481.534437] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B
<7> [481.534886] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B
<7> [481.535312] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C
<7> [481.535752] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C
<7> [481.536187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C
<7> [481.536563] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [481.536902] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:102:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [481.537242] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DP-MST A] hw state readout: disabled, pipe A
<7> [481.537557] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:105:DP-MST B] hw state readout: disabled, pipe B
<7> [481.537855] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DP-MST C] hw state readout: disabled, pipe C
<7> [481.538135] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:117:DDI C/PHY C] hw state readout: disabled, pipe A
<7> [481.538368] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:119:DP-MST A] hw state readout: disabled, pipe A
<7> [481.538633] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:120:DP-MST B] hw state readout: disabled, pipe B
<7> [481.538941] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:121:DP-MST C] hw state readout: disabled, pipe C
<7> [481.539191] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1
<7> [481.539464] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [481.539773] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0
<7> [481.540087] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0
<7> [481.540483] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:eDP-1] hw state readout: disabled
<7> [481.540793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:103:DP-1] hw state readout: disabled
<7> [481.541050] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:112:HDMI-A-1] hw state readout: disabled
<7> [481.541305] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:118:DP-2] hw state readout: disabled
<7> [481.541615] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:124:HDMI-A-2] hw state readout: disabled
<7> [481.541901] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [481.542215] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz
<7> [481.542520] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz
<7> [481.542807] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [481.543109] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz
<7> [481.543368] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz
<7> [481.543607] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz
<7> [481.543850] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [481.544062] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz
<7> [481.544265] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz
<7> [481.544485] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz
<7> [481.544736] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [481.545031] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]
<7> [481.545242] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]
<7> [481.545468] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]
<7> [481.545759] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling
<7> [481.546014] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [481.546229] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [481.546468] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [481.546797] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [481.546961] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [481.547145] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0
<7> [481.547349] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 GT workarounds on global
<7> [481.549289] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [481.549534] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0
<7> [481.549730] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 context workarounds on rcs'0
<7> [481.566700] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV
<7> [481.567099] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping
<7> [481.567299] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping
<7> [481.567524] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping
<7> [481.567795] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [481.568024] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [481.568830] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [481.569003] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [481.569233] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [481.569432] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [481.576781] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:95:eDP-1] backlight device intel_backlight registered
<7> [481.577273] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [481.580572] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:eDP-1] generating connector hotplug event
<7> [481.581414] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [481.584391] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:103:DP-1] generating connector hotplug event
<7> [481.585535] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:112:HDMI-A-1] generating connector hotplug event
<7> [481.586313] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DDI C/PHY C bus for card0-DP-2
<7> [481.587828] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:118:DP-2] generating connector hotplug event
<7> [481.588903] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:124:HDMI-A-2] generating connector hotplug event
<6> [481.589018] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [481.593581] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 5 outputs detected
<6> [481.624946] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [481.633487] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input78
<7> [481.635542] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)
<7> [481.637019] [drm:drm_client_modeset_probe]
<7> [481.636945] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D
<7> [481.637314] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C
<7> [481.637901] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B
<7> [481.638259] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [481.638219] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E
<7> [481.638337] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [481.639675] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [481.639994] i915 device info: pciid=0x1916 rev=0x07 platform=SKYLAKE (subplatform=0x1) gen=9
<7> [481.640002] i915 device info: graphics version: 9
<7> [481.640006] i915 device info: media version: 9
<7> [481.640011] i915 device info: display version: 9
<7> [481.640015] i915 device info: graphics stepping: H0
<7> [481.640019] i915 device info: media stepping: H0
<7> [481.640023] i915 device info: display stepping: H0
<7> [481.640027] i915 device info: base die stepping: **
<7> [481.640031] i915 device info: gt: 2
<7> [481.640035] i915 device info: memory-regions: 0x21
<7> [481.640039] i915 device info: page-sizes: 0x11000
<7> [481.640044] i915 device info: platform: SKYLAKE
<7> [481.640048] i915 device info: ppgtt-size: 48
<7> [481.640053] i915 device info: ppgtt-type: 2
<7> [481.640057] i915 device info: dma_mask_size: 39
<7> [481.640061] i915 device info: is_mobile: no
<7> [481.640065] i915 device info: is_lp: no
<7> [481.640069] i915 device info: require_force_probe: no
<7> [481.640073] i915 device info: is_dgfx: no
<7> [481.640077] i915 device info: has_64bit_reloc: yes
<7> [481.640081] i915 device info: has_64k_pages: no
<7> [481.640085] i915 device info: gpu_reset_clobbers_display: no
<7> [481.640089] i915 device info: has_reset_engine: yes
<7> [481.640093] i915 device info: has_3d_pipeline: yes
<7> [481.640109] i915 device info: has_4tile: no
<7> [481.640114] i915 device info: has_flat_ccs: no
<7> [481.640117] i915 device info: has_global_mocs: no
<7> [481.640122] i915 device info: has_gmd_id: no
<7> [481.639967] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [481.640126] i915 device info: has_gt_uc: yes
<7> [481.640130] i915 device info: has_heci_pxp: no
<7> [481.640134] i915 device info: has_heci_gscfi: no
<7> [481.640137] i915 device info: has_guc_deprivilege: no
<7> [481.640141] i915 device info: has_l3_ccs_read: no
<7> [481.640145] i915 device info: has_l3_dpf: no
<7> [481.640148] i915 device info: has_llc: yes
<7> [481.640152] i915 device info: has_logical_ring_contexts: yes
<7> [481.640156] i915 device info: has_logical_ring_elsq: no
<7> [481.640159] i915 device info: has_media_ratio_mode: no
<7> [481.640163] i915 device info: has_mslice_steering: no
<7> [481.640167] i915 device info: has_oa_bpc_reporting: no
<7> [481.640171] i915 device info: has_oa_slice_contrib_limits: no
<7> [481.640174] i915 device info: has_oam: no
<7> [481.640178] i915 device info: has_one_eu_per_fuse_bit: no
<7> [481.640182] i915 device info: has_pxp: no
<7> [481.640185] i915 device info: has_rc6: yes
<7> [481.640189] i915 device info: has_rc6p: no
<7> [481.640192] i915 device info: has_rps: yes
<7> [481.640196] i915 device info: has_runtime_pm: yes
<7> [481.640200] i915 device info: has_snoop: no
<7> [481.640203] i915 device info: has_coherent_ggtt: yes
<7> [481.640207] i915 device info: tuning_thread_rr_after_dep: no
<7> [481.640211] i915 device info: unfenced_needs_alignment: no
<7> [481.640214] i915 device info: hws_needs_physical: no
<7> [481.640218] i915 device info: has_pooled_eu: no
<7> [481.640222] i915 device info: cursor_needs_physical: no
<7> [481.640225] i915 device info: has_cdclk_crawl: no
<7> [481.640229] i915 device info: has_cdclk_squash: no
<7> [481.640233] i915 device info: has_ddi: yes
<7> [481.640236] i915 device info: has_dp_mst: yes
<7> [481.640240] i915 device info: has_dsb: no
<7> [481.640244] i915 device info: has_fpga_dbg: yes
<7> [481.640247] i915 device info: has_gmch: no
<7> [481.640251] i915 device info: has_hotplug: yes
<7> [481.640255] i915 device info: has_hti: no
<7> [481.640258] i915 device info: has_ipc: yes
<7> [481.640262] i915 device info: has_overlay: no
<7> [481.640265] i915 device info: has_psr: yes
<7> [481.640269] i915 device info: has_psr_hw_tracking: yes
<7> [481.640272] i915 device info: overlay_needs_physical: no
<7> [481.640302] i915 device info: supports_tv: no
<7> [481.640307] i915 device info: has_hdcp: yes
<7> [481.640311] i915 device info: has_dmc: yes
<7> [481.640315] i915 device info: has_dsc: no
<7> [481.640319] i915 device info: rawclk rate: 24000 kHz
<7> [481.640324] i915 device info: iommu: disabled
<7> [481.640328] i915 device info: available engines: 40403
<7> [481.640332] i915 device info: slice total: 1, mask=0001
<7> [481.640336] i915 device info: subslice total: 3
<7> [481.640341] i915 device info: slice0: 3 subslices, mask=00000007
<7> [481.640346] i915 device info: slice1: 0 subslices, mask=00000000
<7> [481.640350] i915 device info: slice2: 0 subslices, mask=00000000
<7> [481.640354] i915 device info: EU total: 24
<7> [481.640358] i915 device info: EU per subslice: 8
<7> [481.640363] i915 device info: has slice power gating: no
<7> [481.640367] i915 device info: has subslice power gating: no
<7> [481.640370] i915 device info: has EU power gating: yes
<6> [481.640375] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [481.640379] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [481.640384] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [481.640286] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [481.640754] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [481.641059] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [481.641542] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [481.641556] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [481.641567] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [481.641636] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [481.641934] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [481.643029] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [481.643338] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [481.644480] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [481.645338] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] status updated from unknown to connected
<7> [481.646841] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [481.646878] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [481.646892] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [481.646905] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [481.646938] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [481.647412] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] status updated from unknown to disconnected
<7> [481.647482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [481.647522] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1]
<7> [481.647551] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [481.648871] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [481.649199] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [481.652755] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [481.653124] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [481.653137] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [481.653428] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [481.657736] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [481.657750] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [481.658061] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] status updated from unknown to disconnected
<7> [481.658112] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [481.658142] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2]
<7> [481.658171] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [481.658829] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] status updated from unknown to disconnected
<7> [481.658876] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] disconnected
<7> [481.658904] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2]
<7> [481.658931] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [481.659737] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [481.660038] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [481.660719] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [481.661033] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [481.661045] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [481.661336] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [481.665149] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [481.665163] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [481.665750] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] status updated from unknown to disconnected
<7> [481.665801] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [481.665830] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [481.665839] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [481.665847] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [481.665854] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [481.665861] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [481.666182] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [481.666220] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [481.666227] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [481.666234] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [481.666241] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [481.666264] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<7> [481.666423] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<7> [481.666813] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [481.672788] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x000c0000
<6> [481.674394] fbcon: i915drmfb (fb0) is primary device
<6> [481.675676] Console: switching to colour frame buffer device 400x112
<6> [481.675700] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [481.688728] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [481.688768] [drm:drm_client_modeset_probe]
<7> [481.689312] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [481.689386] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [481.691019] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [481.691290] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [481.691565] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [481.691806] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [481.692263] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [481.692277] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [481.692287] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [481.692346] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [481.692640] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [481.693717] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [481.693987] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [481.695251] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [481.695297] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [481.695314] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [481.695330] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [481.695365] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [481.696501] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [481.696539] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1]
<7> [481.696569] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [481.697805] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [481.698082] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [481.701724] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [481.702070] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [481.702084] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [481.702329] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [481.706552] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [481.706567] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [481.706844] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [481.706878] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2]
<6> [481.706981] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040380
<7> [481.706908] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [481.707211] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] disconnected
<7> [481.707243] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2]
<7> [481.707271] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [481.708556] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [481.708817] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [481.714530] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [481.714838] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [481.714851] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<6> [481.715094] [IGT] i915_suspend: finished subtest basic-s2idle-without-i915, SUCCESS
<7> [481.715093] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [481.715233] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [481.716370] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [481.716894] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [481.718895] [IGT] i915_suspend: exiting, ret=0
<7> [481.719370] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [481.721368] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [481.721384] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [481.721902] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2] disconnected
<7> [481.721937] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [481.721947] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [481.721954] [drm:drm_client_modeset_probe] connector 112 enabled? no
<7> [481.721961] [drm:drm_client_modeset_probe] connector 118 enabled? no
<7> [481.721967] [drm:drm_client_modeset_probe] connector 124 enabled? no
<7> [481.722197] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [481.722230] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [481.722238] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [481.722245] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [481.722252] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [481.722877] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 51 (0,0)
<6> [481.722816] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [481.723582] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [481.724294] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10
<7> [481.724318] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:95:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [481.724644] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 373250KHz
<7> [481.724894] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [481.725138] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1119750 available 2160000
<7> [481.725394] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:95:eDP-1] SDP split enable: no
<7> [481.725670] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:51:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [481.725939] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:94:DDI A/PHY A] [CRTC:51:pipe A]
<7> [481.726188] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [481.726477] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [481.726746] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [481.727016] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [481.727285] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4348677/8388608 link 362389/524288)
<7> [481.729739] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [481.730044] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [481.730315] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [481.730890] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3360)
<7> [481.731163] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [481.731430] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3360)
<7> [481.732119] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [481.732398] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<7> [481.732861] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [481.733130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1852)
<7> [481.733398] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [481.733882] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1852)
<7> [481.734153] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1803)
<7> [481.734422] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1808)
<7> [481.734915] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [481.735185] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3360)
<7> [481.735834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [481.736103] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3360)
<7> [481.736367] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [481.736824] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [481.737089] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [481.737357] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1852)
<7> [481.737733] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [481.738110] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1852)
<7> [481.738378] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1803)
<7> [481.738903] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1808)
<7> [481.739173] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [481.739628] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [481.739901] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [481.740172] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in dpll_hw_state.ctrl1 (expected 0x00000000, found 0x00000001)
<7> [481.740664] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [481.740938] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 373250)
<7> [481.741203] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 373250)
<7> [481.741672] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:51:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [481.741947] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [481.742297] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:51:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 892), active pipes 0x0 -> 0x1
<7> [481.742857] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 856), size 0 -> 856
<7> [481.743123] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:47:cursor A] ddb ( 0 - 0) -> ( 856 - 892), size 0 -> 36
<7> [481.743388] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7, twm, swm, stwm
<7> [481.743875] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [481.744144] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 7, 58, 84, 96, 184, 227, 245, 288, 0, 0, 0
<7> [481.744411] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 8, 59, 85, 97, 185, 228, 246, 289, 0, 0, 0
<7> [481.744995] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (373250 kHz) > [CRTC:51:pipe A] min cdclk (0 kHz)
<7> [481.745285] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (23329 kHz) > old min cdclk (0 kHz)
<7> [481.745847] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [481.746132] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 450000 kHz, actual 450000 kHz
<7> [481.746410] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [481.746939] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:51:pipe A] allocated DPLL 0
<7> [481.747202] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:51:pipe A] reserving DPLL 0
<7> [481.747656] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: yes [modeset]
<7> [481.747918] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [481.748201] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [481.748570] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [481.754467] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [481.754766] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [481.755032] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [481.755316] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4348677, data_n: 8388608, link_m: 362389, link_n: 524288, tu: 64
<7> [481.755621] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [481.755906] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [481.756185] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4
<7> [481.756496] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0
<7> [481.756504] i915 0000:00:02.0: pixelformat: RGB
<7> [481.756511] i915 0000:00:02.0: colorimetry: sRGB
<7> [481.756517] i915 0000:00:02.0: bpc: 0
<7> [481.756523] i915 0000:00:02.0: dynamic range: VESA range
<7> [481.756530] i915 0000:00:02.0: content type: Not defined
<7> [481.756551] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [481.756835] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [481.757114] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [481.757394] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [481.758029] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [481.758313] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=373250, hd=3200 hb=3200-3360 hs=3248-3280 ht=3360, vd=1800 vb=1800-1852 vs=1803-1808 vt=1852, flags=0xa
<7> [481.758632] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 373250
<7> [481.758903] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 73, ips linetime: 0
<7> [481.759170] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [481.759435] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [481.759927] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [481.760194] i915 0000:00:02.0: [drm:skl_dump_hw_state [i915]] dpll_hw_state: ctrl1: 0x1, cfgcr1: 0x0, cfgcr2: 0x0
<7> [481.760479] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x2 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [481.760741] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [481.761004] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [481.761267] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [481.761758] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [481.762029] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [481.762297] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [481.762674] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:96] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [481.763048] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [481.763319] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [481.763841] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no
<7> [481.764112] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no
<7> [481.765730] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 450000 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 1
<7> [481.766985] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:94:DDI A/PHY A]
<7> [481.767265] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:102:DDI B/PHY B]
<7> [481.767719] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:104:DP-MST A]
<7> [481.767976] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:105:DP-MST B]
<7> [481.768231] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:106:DP-MST C]
<7> [481.768683] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:117:DDI C/PHY C]
<7> [481.768940] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:119:DP-MST A]
<7> [481.769194] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:120:DP-MST B]
<7> [481.769701] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:121:DP-MST C]
<7> [481.769960] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [481.770417] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [481.770903] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 2
<7> [481.771188] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 3
<7> [481.771818] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:51:pipe A]
<7> [481.772111] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [481.772872] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 turn panel power on
<7> [481.773223] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [481.773763] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000008
<7> [481.774019] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [481.774277] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 wait for panel power on
<7> [481.774765] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:94:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000000b
<6> [481.792674] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC3246: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:speaker
<6> [481.792912] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [481.792920] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [481.792927] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [481.792933] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [481.792939] snd_hda_codec_realtek hdaudioC0D0: Headset Mic=0x19
<6> [481.792945] snd_hda_codec_realtek hdaudioC0D0: Headphone Mic=0x1a
<6> [481.792951] snd_hda_codec_realtek hdaudioC0D0: Internal Mic=0x12
<7> [481.859389] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [481.859684] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [481.859880] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [481.860076] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [481.860258] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [481.861721] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [481.862032] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [481.862254] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<7> [481.862491] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [481.904690] input: HDA Intel PCH Headphone Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input79
<6> [481.909644] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input80
<6> [481.923403] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input81
<6> [481.924568] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input82
<7> [481.975478] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [481.975772] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E
<7> [481.976312] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [481.979920] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 84 40 00 00 01 01 02 00 00 00 00 0b 00
<7> [481.982209] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [481.983436] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [481.983787] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 00000000
<7> [481.984118] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [481.987421] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Clock recovery OK
<7> [481.987948] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] >=5.4/6.48 Gbps link rate without sink TPS3 support
<7> [481.988195] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Using DP training pattern TPS2
<7> [481.991593] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 2/2/2/2, pre-emphasis request: 1/1/1/1
<7> [481.991867] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 2(max)/2(max)/2(max)/2(max), pre-emphasis levels: 1/1/1/1
<7> [481.992126] i915 0000:00:02.0: [drm:hsw_set_signal_levels [i915]] Using signal levels 08000000
<7> [481.994090] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [481.994350] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:95:eDP-1][ENCODER:94:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [481.995050] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [481.995662] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [481.995908] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [481.996330] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:95:eDP-1] set backlight PWM = 937
<7> [481.996827] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23040000 bytes of contiguous stolen space for FBC, limit: 1
<7> [481.997111] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [482.012706] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR1
<7> [482.017152] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:95:eDP-1]
<7> [482.017536] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A]
<7> [482.018345] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [482.018747] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [482.029611] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [482.029646] [drm:drm_client_modeset_probe]
<7> [482.029747] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [482.029781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [482.032272] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [482.032618] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [482.032872] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [482.033122] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [482.033434] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [482.033475] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [482.033486] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [482.033740] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [482.034008] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [482.035061] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [482.035325] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [482.036826] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [482.036858] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 373250 3200 3248 3280 3360 1800 1803 1808 1852 0x48 0xa
<7> [482.036873] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 48 298600 3200 3248 3280 3360 1800 1803 1808 1852 0x40 0xa
<7> [482.036886] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [482.036918] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [482.037240] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [482.037272] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1]
<7> [482.037302] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:112:HDMI-A-1]
<7> [482.039500] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [482.039794] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry
<7> [482.040282] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)
<7> [482.040591] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [482.040604] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [482.040845] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [482.044383] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [482.044396] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [482.045231] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:112:HDMI-A-1] disconnected
<7> [482.045268] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2]
<7> [482.045300] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:118:DP-2]
<7> [482.045647] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:118:DP-2] disconnected
<7> [482.045678] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:124:HDMI-A-2]
<7> [482.045707] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:124:HDMI-A-2]
<7> [482.046412] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [482.046703] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [482.047171] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [482.047463] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [482.047475] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [482.047725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [482.051258] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
|