Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g34b68fb58 (x86_64) (Linux: 6.5.0-linus-v6.5-g2dde18cd1d8f+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.566s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.566s)
Dmesg
<6> [497.813181] Console: switching to colour dummy device 80x25
<6> [497.817327] [IGT] kms_force_connector_basic: executing
<7> [497.909182] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [497.917368] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [497.919998] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [497.929599] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [497.929683] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [497.929921] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [497.983649] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [497.998218] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [497.998299] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.000241] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [498.014690] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.014774] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [498.016752] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [498.017412] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.017746] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.070642] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.083284] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.083364] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.085604] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [498.097036] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.097107] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [498.098948] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [498.101844] [drm:status_store] [CONNECTOR:125:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [498.101920] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [498.102129] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [498.155712] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [498.169084] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [498.169166] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.170940] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [498.184980] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [498.185047] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [498.186994] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [498.187841] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [498.188033] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [498.240421] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [498.251184] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [498.251240] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.252805] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [498.264995] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [498.265070] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [498.266710] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [498.269650] [drm:status_store] [CONNECTOR:135:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [498.269729] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [498.269943] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [498.323769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [498.336197] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [498.336260] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.337817] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [498.350790] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [498.350856] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [498.352745] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [498.353776] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [498.353981] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [498.407707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [498.418841] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [498.418918] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.420598] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [498.433942] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [498.434020] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [498.435797] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [498.436323] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.436674] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.489726] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.502976] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.503056] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.504993] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [498.518287] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.518365] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [498.520321] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<6> [498.526044] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [498.528725] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [498.528803] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.529020] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.582666] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.601424] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.601686] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.603682] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [498.621914] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.622078] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [498.623988] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] status updated from disconnected to connected
<7> [498.627411] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [498.627714] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [498.627798] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [498.627869] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [498.627937] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [498.628006] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [498.628774] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.628972] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.683657] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.698581] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.698727] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.700639] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [498.718579] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.718725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [498.722041] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [498.722244] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [498.722321] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [498.722386] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [498.722449] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [498.722671] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [498.755160] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:113:HDMI-A-1] EDID override set
<7> [498.755648] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.755868] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.759605] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:113:HDMI-A-1] ELD monitor IGT
<7> [498.759684] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:113:HDMI-A-1] ELD size 24, SAD count 0
<7> [498.810645] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.824618] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [498.826614] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [498.826707] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [498.826814] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [498.826886] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [498.826986] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [498.827180] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [498.827248] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [498.827312] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [498.827374] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [498.827436] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [498.829595] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:113:HDMI-A-1] EDID override reset
<7> [498.830343] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.830661] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.884739] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.898105] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.898255] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.900094] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [498.911856] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.911968] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [498.913627] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:113:HDMI-A-1] EDID changed, epoch counter 2
<7> [498.914933] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [498.915021] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [498.915125] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [498.915196] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [498.915298] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [498.915629] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [498.915697] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [498.915760] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [498.915819] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [498.915878] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [498.918228] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [498.918303] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [498.918934] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [498.972742] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [498.988027] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [498.988112] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [498.989991] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [499.004069] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.004155] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [499.006090] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] status updated from connected to disconnected
<7> [499.006399] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [499.008447] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [499.008839] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [499.062739] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [499.073654] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.073712] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.075058] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [499.088242] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.088325] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [499.091701] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<6> [499.097864] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [499.099611] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [499.104789] [drm:status_store] [CONNECTOR:95:eDP-1] force updated from 0 to 0 or reprobing
<7> [499.104852] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [499.105012] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [499.108356] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [499.110079] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [499.111885] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [499.114943] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [499.117118] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [499.117204] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [499.117276] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [499.117701] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [499.119712] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [499.123972] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [499.125856] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [499.130714] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [499.130924] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [499.131621] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [499.131828] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [499.135569] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [499.137348] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [499.138792] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [499.140723] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [499.142583] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [499.142664] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [499.142724] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [499.142943] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [499.144751] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [499.148704] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [499.150591] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [499.154999] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [499.155195] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [499.157050] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:eDP-1] EDID override reset
<7> [499.157383] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [499.157948] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [499.161872] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [499.163654] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [499.165576] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [499.167374] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [499.169640] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [499.169715] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [499.169777] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [499.170004] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [499.171803] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [499.175712] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [499.177584] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [499.182294] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [499.182574] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [499.184679] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:103:DP-1] EDID override reset
<7> [499.185002] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [499.185210] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [499.187226] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [499.190133] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [499.190208] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [499.190425] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [499.243788] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [499.256138] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.256203] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.257932] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [499.270735] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.270820] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [499.272915] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [499.274032] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [499.274239] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [499.326778] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [499.340962] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.341039] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.342545] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [499.354420] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.354589] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [499.356379] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [499.358139] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:113:HDMI-A-1] EDID override reset
<7> [499.358612] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [499.358826] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [499.412645] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [499.426947] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.427006] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.428617] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [499.441313] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [499.441375] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [499.442898] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [499.445030] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:119:DP-2] EDID override reset
<7> [499.445354] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [499.445726] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [499.447821] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] disconnected
<7> [499.450606] [drm:status_store] [CONNECTOR:125:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [499.450684] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [499.450898] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [499.504662] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [499.518602] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [499.518667] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.520060] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [499.535419] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [499.535610] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [499.537678] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [499.538451] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [499.538808] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [499.592707] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [499.604990] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [499.605050] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.606942] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [499.618291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [499.618370] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [499.619931] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [499.621622] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:125:HDMI-A-2] EDID override reset
<7> [499.621951] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [499.622158] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [499.675737] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [499.688776] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [499.688854] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.690230] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [499.702397] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [499.702573] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [499.704441] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [499.706426] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:129:DP-3] EDID override reset
<7> [499.706917] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3]
<7> [499.707128] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:129:DP-3]
<7> [499.708829] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3] disconnected
<7> [499.711183] [drm:status_store] [CONNECTOR:135:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [499.711242] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [499.711389] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [499.764752] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [499.776924] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [499.776988] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.779252] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [499.794881] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [499.794966] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [499.796704] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [499.798187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [499.798437] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [499.851650] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [499.865266] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [499.865327] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.866904] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [499.878935] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [499.878995] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [499.880623] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [499.882453] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:135:HDMI-A-3] EDID override reset
<7> [499.883099] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [499.883308] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [499.935708] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [499.947436] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [499.947599] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [499.948934] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [499.963129] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [499.963208] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [499.965884] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<6> [499.976801] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [499.979015] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [499.979097] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [499.980097] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [500.033711] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [500.047599] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [500.047683] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [500.049626] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [500.063794] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [500.063886] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [500.065852] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [500.066892] [drm:status_store] [CONNECTOR:125:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [500.066965] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [500.067178] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [500.121712] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [500.134076] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [500.134139] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [500.135638] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [500.148277] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [500.148340] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [500.149763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [500.150701] [drm:status_store] [CONNECTOR:135:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [500.150777] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [500.150984] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [500.205746] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [500.220390] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [500.220570] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [500.222008] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [500.237679] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [500.237745] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [500.239182] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [500.241123] [drm:status_store] [CONNECTOR:95:eDP-1] force updated from 0 to 0 or reprobing
<7> [500.241198] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [500.241352] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [500.244598] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [500.246012] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [500.248332] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [500.250790] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [500.253030] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [500.253115] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [500.253178] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [500.253590] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [500.255707] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [500.259091] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [500.260418] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [500.264264] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [500.264408] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [500.268886] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [500.298732] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [500.298928] [drm:drm_client_modeset_probe]
<7> [500.299926] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [500.300155] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [500.303829] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [500.305229] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [500.306614] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [500.308402] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [500.311209] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [500.311300] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [500.311370] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [500.311820] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [500.313698] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [500.318059] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [500.320076] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [500.324103] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [500.324250] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [500.324312] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [500.324443] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [500.326685] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [500.326903] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [500.327100] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [500.380722] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [500.395212] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [500.395299] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [500.397206] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [500.414427] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [500.414701] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [500.417430] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [500.417894] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [500.418096] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [500.420198] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] disconnected
<7> [500.420444] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [500.421699] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [500.474710] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [500.489040] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [500.489125] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [500.491048] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [500.507726] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [500.507815] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [500.510624] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [500.510848] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3]
<7> [500.511039] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:129:DP-3]
<7> [500.513917] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3] disconnected
<7> [500.514127] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [500.514316] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [500.568661] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [500.582931] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [500.583015] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [500.585102] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [500.602114] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [500.602203] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [500.604227] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [500.604434] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [500.604651] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [500.604700] [drm:drm_client_modeset_probe] connector 113 enabled? no
<7> [500.604744] [drm:drm_client_modeset_probe] connector 119 enabled? no
<7> [500.604786] [drm:drm_client_modeset_probe] connector 125 enabled? no
<7> [500.604829] [drm:drm_client_modeset_probe] connector 129 enabled? no
<7> [500.604870] [drm:drm_client_modeset_probe] connector 135 enabled? no
<7> [500.605358] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [500.605669] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [500.605720] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [500.605765] [drm:drm_client_modeset_probe] found mode 2400x1600
<7> [500.605807] [drm:drm_client_modeset_probe] picking CRTCs for 2400x1600 config
<7> [500.606055] [drm:drm_client_modeset_probe] desired mode 2400x1600 set on crtc 51 (0,0)
<6> [500.676557] Console: switching to colour frame buffer device 300x100
Created at 2023-08-27 23:51:53