Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g34b68fb58 (x86_64) (Linux: 6.5.0-linus-v6.5-g2dde18cd1d8f+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.016s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.016s)
Dmesg
<6> [130.286753] Console: switching to colour dummy device 80x25
<6> [130.287173] [IGT] kms_force_connector_basic: executing
<7> [130.329326] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [130.330078] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [130.330653] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [130.331308] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [130.331319] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.331351] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.331556] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.331743] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.332179] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.332363] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.332731] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.332952] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.332962] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.333170] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.334064] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.334072] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.334341] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.334361] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.334369] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.334375] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.334380] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.334386] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.334430] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.334451] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.334646] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.334849] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.335265] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.335448] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.335811] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.336028] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.336035] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.336242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.337163] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.337170] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.337425] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.337445] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.337451] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.337456] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.337461] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.337466] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.337523] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.337543] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.337758] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.337962] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.338377] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.338560] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.338942] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.339128] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.339133] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.339318] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.340236] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.340243] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.340497] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.340517] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.340522] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.340527] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.340532] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.340537] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [130.340845] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [130.341086] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 2 or reprobing
<7> [130.341094] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.341331] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.341530] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.341905] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.342092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.342108] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.342294] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.343197] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.343213] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.343476] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.343496] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.343503] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.343508] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.343514] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.343520] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.343569] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.343795] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.344087] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.344454] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.344639] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.344652] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.344858] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.345760] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.345772] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.346069] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.346089] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.346095] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.346100] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.346105] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.346110] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.346397] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [130.346428] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.346490] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [130.346497] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [130.346646] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.346653] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [130.346663] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.346669] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [130.346678] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.346696] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [130.346702] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [130.346707] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [130.346712] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.346716] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.346721] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.346939] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [130.346985] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.347043] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [130.347050] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [130.347055] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:61:VGA-1] EDID changed, epoch counter 6
<7> [130.347197] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [130.347204] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [130.347213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.347231] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [130.347237] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [130.347242] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.347247] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.347251] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.347390] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [130.347424] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.347649] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.347884] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.348334] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.348525] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.348544] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.348786] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.349741] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.349756] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.350035] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [130.350047] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [130.350062] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [130.350072] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [130.350086] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.350114] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.350120] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.350125] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.350130] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.350135] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.350324] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 2 to 0 or reprobing
<7> [130.350332] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.350353] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.350551] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.350738] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.351164] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.351383] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.351753] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.351982] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.351991] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.352239] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.353132] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.353140] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.353404] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.353425] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.353431] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.353437] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.353442] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.353448] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.353495] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.353516] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.353711] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.353921] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.354372] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.354555] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.354948] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.355153] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.355158] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.355344] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.356234] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.356242] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.356498] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.356518] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.356524] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.356529] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.356534] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.356539] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [130.356858] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [130.357113] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [130.357641] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [130.357650] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.357675] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.357912] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.358152] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.358546] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.358730] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.359178] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.359365] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.359372] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.359558] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.360457] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.360466] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.360731] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.360752] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.360758] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.360764] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.360769] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.360775] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.360836] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.360859] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.361133] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.361319] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.361703] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.361911] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.362322] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.362507] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.362513] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.362698] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.363607] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.363614] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.363897] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.363927] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.363937] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.363945] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.363953] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.363962] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.364117] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [130.364147] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.364168] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.364379] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.364573] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.364973] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.365208] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.365574] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.365759] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.365764] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.366056] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.367000] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.367011] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.367283] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.367303] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.367309] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.367314] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.367319] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.367324] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.367557] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [130.367565] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [130.367587] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [130.368004] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.368212] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [130.368581] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.368767] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.368773] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.369083] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [130.370015] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.370023] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [130.370212] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [130.370273] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [130.370294] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [130.370678] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.370888] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [130.371315] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.371500] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.371505] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.371686] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [130.372584] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.372592] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [130.372778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [130.373000] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:64:HDMI-A-1] EDID override reset
<7> [130.373036] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [130.373058] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [130.373442] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.373625] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [130.374007] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.374193] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.374198] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.374379] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [130.375270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.375278] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [130.375465] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [130.375629] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:72:DP-1] EDID override reset
<7> [130.375657] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:72:DP-1]
<7> [130.375679] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-1]
<7> [130.375901] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:72:DP-1] disconnected
<6> [130.376657] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [130.376868] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [130.376879] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [130.376912] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [130.377167] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [130.377353] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [130.377745] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.378016] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [130.378441] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [130.378627] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.378635] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.378821] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [130.379742] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [130.379749] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [130.380074] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [130.380105] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [130.380115] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [130.380121] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [130.380127] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [130.380132] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [130.380202] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [130.380209] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [130.380230] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [130.380620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.380803] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [130.381220] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [130.381411] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.381418] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [130.381599] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [130.382498] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [130.382506] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [130.382693] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [130.383098] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [130.413477] Console: switching to colour frame buffer device 128x48
Created at 2023-08-27 23:51:53