igt@i915_pm_rpm@basic-pci-d3-state on bat-jsl-3@linus-v6.5 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g34b68fb58 (x86_64) (Linux: 6.5.0-linus-v6.5-g2dde18cd1d8f+ x86_64)
Out	Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 1 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa3f/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 set_property_atomic+0x87/0x160 drm_mode_obj_set_property_ioctl+0xc0/0x110 Wakeref count: 1 Wakeref x1 taken at: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] __intel_display_power_put_async+0x38/0x120 [i915] hsw_get_pipe_config+0x150/0xb30 [i915] intel_crtc_get_pipe_config+0x1f/0x50 [i915] intel_modeset_verify_crtc+0xc7/0x4e0 [i915] intel_atomic_commit_tail+0x7b5/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (4.408s)
Err	Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (4.408s)
Dmesg	<6> [245.319134] Console: switching to colour dummy device 80x25 <6> [245.320052] [IGT] i915_pm_rpm: executing <7> [245.333723] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [245.334864] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] <7> [245.334912] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [245.335879] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [245.336177] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [245.336482] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [245.336767] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [245.337095] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [245.337109] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [245.337117] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [245.337150] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [245.337480] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [245.338577] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [245.338882] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [245.339923] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes : <7> [245.339959] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [245.339971] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [245.340160] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] <7> [245.340196] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [245.340554] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected <7> [245.340735] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] <7> [245.340769] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [245.341098] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected <7> [245.341268] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [245.341301] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [245.341641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [245.358786] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] <7> [245.358833] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [245.359211] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected <7> [245.360258] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] <7> [245.360299] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [245.360726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected <7> [245.361913] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [245.361949] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [245.362286] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [245.363729] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] <7> [245.363769] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [245.364672] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [245.364969] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [245.365262] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [245.365576] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [245.365914] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [245.365928] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [245.365936] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [245.365972] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [245.366254] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [245.367324] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [245.367635] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [245.368677] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes : <7> [245.368714] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [245.368726] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa <7> [245.368782] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] <7> [245.368815] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [245.369132] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected <7> [245.369194] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] <7> [245.369225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [245.369564] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected <7> [245.369627] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] <7> [245.369658] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [245.369978] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected <7> [245.370577] i915 0000:00:02.0: [drm:drm_mode_addfb2] [FB:268] <7> [246.459653] [drm:drm_mode_setcrtc] [CRTC:98:pipe A] <7> [246.459837] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 1, found 0) <7> [246.460200] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 1, found 0) <7> [246.460525] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1) <7> [246.460834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 4, found 0) <7> [246.461128] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0) <7> [246.461437] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000) <7> [246.461738] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0) <7> [246.462027] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0) <7> [246.462313] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3316, found 0) <7> [246.462615] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0) <7> [246.462906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0) <7> [246.463190] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0) <7> [246.463509] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0) <7> [246.463805] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0) <7> [246.464088] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1816, found 0) <7> [246.464385] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0) <7> [246.464677] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0) <7> [246.464960] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0) <7> [246.465240] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0) <7> [246.465540] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0) <7> [246.465830] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3316, found 0) <7> [246.466110] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0) <7> [246.466404] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0) <7> [246.466692] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0) <7> [246.466975] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0) <7> [246.467256] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0) <7> [246.467575] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0) <7> [246.467866] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0) <7> [246.468149] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0) <7> [246.468463] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0) <7> [246.468764] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0) <7> [246.469057] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0) <7> [246.469432] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0) <7> [246.469735] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0) <7> [246.470029] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0) <7> [246.470315] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 361310, found 0) <7> [246.470619] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 361310, found 0) <7> [246.470916] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 540000, found 0) <7> [246.471206] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [246.471508] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0 <7> [246.471842] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0 <7> [246.472228] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0 <7> [246.472554] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0 <7> [246.472854] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [246.473131] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [246.473425] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [246.473706] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [246.473982] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0 <7> [246.474273] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [246.474585] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0 <7> [246.474881] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0 <7> [246.475234] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [246.475542] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz <7> [246.475842] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0 <7> [246.476153] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset] <7> [246.477719] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [246.478044] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [246.478359] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [246.478672] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [246.478975] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [246.479275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [246.479594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [246.479895] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [246.491382] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [246.700410] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0 <7> [246.700964] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [246.704582] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off <7> [246.704927] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time <7> [246.705263] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [246.710873] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [246.711180] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [246.711468] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [246.711813] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [246.732064] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [246.732392] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [246.732674] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20 <7> [246.733026] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [246.758405] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [246.758731] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [246.759042] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A] <7> [246.759372] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [246.759681] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [246.760051] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [246.760350] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [246.760633] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30 <7> [246.760940] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [246.760971] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A] <7> [246.761267] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [246.761739] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [246.762047] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [246.762364] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [246.762662] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [246.762950] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [246.763226] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [246.763525] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [246.763840] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [246.764141] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [246.764451] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [246.764817] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [246.765315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [246.765659] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [246.765962] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [246.767247] [drm:drm_mode_setcrtc] [CRTC:167:pipe B] <7> [246.767519] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [246.768190] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [246.769084] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.769411] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [246.769708] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.770005] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [246.770299] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.770628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [246.770966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [246.771273] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [246.771617] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [246.772809] [drm:drm_mode_setcrtc] [CRTC:236:pipe C] <7> [246.773050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [246.773735] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [246.774644] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.774961] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [246.775253] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.775585] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [246.775889] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.776199] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [246.776553] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [246.776854] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [246.777143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [246.972373] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [246.973579] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [246.976992] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [246.977879] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.978199] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [246.978512] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.978819] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [246.979108] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.979418] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [246.979709] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [246.980285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [246.980673] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [246.981007] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [246.981288] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [246.985563] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [247.082295] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state <7> [247.105390] [drm:drm_mode_setcrtc] [CRTC:98:pipe A] <7> [247.117735] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [247.122361] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [247.122707] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [247.123023] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [247.123472] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [247.124772] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 50000 kHz, VCO 0 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [247.125109] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [247.125586] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [247.126720] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [247.127028] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [247.134040] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [247.134619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [247.134961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [247.135645] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [247.136533] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.136849] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [247.137156] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.137491] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [247.137802] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.138107] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [247.138442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [247.138743] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [247.139023] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [247.140104] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [247.141327] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [247.143716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [247.144576] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.144903] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [247.145212] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.145538] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [247.145840] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.146143] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [247.146440] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [247.147816] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [247.148188] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.148546] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [247.148838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [247.149513] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [247.150258] [drm:drm_mode_setcrtc] [CRTC:167:pipe B] <7> [247.154411] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [247.178590] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [247.184632] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [247.184979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [247.185307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [247.185845] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [247.186494] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 50000 kHz, VCO 0 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [247.186803] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [247.187202] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [247.188320] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [247.188660] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [247.196582] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [247.197104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [247.197541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [247.198230] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [247.199134] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.199528] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [247.199837] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.200141] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [247.200467] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [247.200791] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [247.201093] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [247.202136] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [247.202518] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [247.364647] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060 <7> [247.372397] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [247.372795] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068 <7> [247.373081] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled <6> [247.415612] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0 <4> [247.415631] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID) <4> [247.415637] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000 <4> [247.415643] nvme 0000:02:00.0: [ 0] RxErr (First) <7> [247.434949] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [247.435289] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [247.435575] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [247.435872] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [247.581229] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [247.581573] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [247.581854] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [247.582137] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [247.582986] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [247.583003] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [247.583012] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [247.583088] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [247.583430] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [247.584875] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [247.585159] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [247.586982] [drm:drm_mode_setcrtc] [CRTC:236:pipe C] <7> [247.587395] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:239:eDP-1] Same epoch counter 1 <7> [247.587454] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [247.588236] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:248:DP-1] Same epoch counter 1 <7> [247.588275] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [247.588655] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] Same epoch counter 6 <7> [247.588694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [247.589032] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1 <7> [247.589081] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [247.590011] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [247.590293] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [247.590593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [247.590871] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [247.591183] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [247.591195] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [247.591204] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [247.591240] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [247.591530] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [247.592633] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [247.592914] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [247.595647] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:239:eDP-1] Same epoch counter 1 <7> [247.595698] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [247.596069] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:248:DP-1] Same epoch counter 1 <7> [247.596107] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [247.596481] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] Same epoch counter 6 <7> [247.596517] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [247.596859] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1 <7> [250.636469] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off <7> [250.636995] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [250.637324] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [250.637690] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [250.638037] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.638364] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [250.639517] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [250.639508] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [250.639813] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [250.640109] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [250.640326] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [250.640435] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [250.642533] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [250.643389] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.643700] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [250.643990] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.644284] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [250.644596] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.644898] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [250.645178] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [250.645669] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [250.645993] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.646315] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [250.646610] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [250.651384] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [250.691173] [drm:drm_mode_setcrtc] [CRTC:98:pipe A] <7> [250.691253] [drm:drm_mode_setcrtc] [CONNECTOR:239:eDP-1] <7> [250.691452] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36) <7> [250.691847] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz <7> [250.692158] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24 <7> [250.692470] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000 <7> [250.692753] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no <7> [250.693032] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long <7> [250.693314] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0 <7> [250.693630] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A] <7> [250.693914] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1) <7> [250.694215] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1) <7> [250.694545] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4) <7> [250.694856] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4) <7> [250.695150] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288) <7> [250.695550] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100) <7> [250.695846] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1) <7> [250.696130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200) <7> [250.696469] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316) <7> [250.696770] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200) <7> [250.697073] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316) <7> [250.697477] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248) <7> [250.697776] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280) <7> [250.698068] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800) <7> [250.698380] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816) <7> [250.698674] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800) <7> [250.698957] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816) <7> [250.699241] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802) <7> [250.699566] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807) <7> [250.699881] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200) <7> [250.700176] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316) <7> [250.700481] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200) <7> [250.700779] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316) <7> [250.701068] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248) <7> [250.701365] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280) <7> [250.701663] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800) <7> [250.701962] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816) <7> [250.702270] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800) <7> [250.702594] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816) <7> [250.702892] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802) <7> [250.703184] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807) <7> [250.703522] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1) <7> [250.703817] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2) <7> [250.704100] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8) <7> [250.704412] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24) <7> [250.704717] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310) <7> [250.705022] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310) <7> [250.705327] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000) <7> [250.705634] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset <7> [250.705996] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1 <7> [250.706387] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985 <7> [250.706669] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39 <7> [250.706950] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm <7> [250.707244] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [250.707570] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 <7> [250.707862] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 <7> [250.708144] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1 <7> [250.708528] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [250.708822] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446 <7> [250.709109] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446 <7> [250.709448] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz) <7> [250.709746] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz) <7> [250.710090] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change <7> [250.710438] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz <7> [250.710747] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1 <7> [250.711037] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0 <7> [250.711321] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0 <7> [250.711629] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset] <7> [250.711919] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB <7> [250.712209] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0 <7> [250.712529] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [250.712832] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [250.713129] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [250.713435] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [250.713731] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64 <7> [250.714019] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [250.714299] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [250.714637] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [250.714938] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2 <7> [250.715240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [250.715557] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa <7> [250.715851] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [250.716142] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa <7> [250.716450] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa <7> [250.716747] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310 <7> [250.717032] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0 <7> [250.717313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [250.717628] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [250.717936] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [250.718239] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [250.718555] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [250.718847] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [250.719138] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000 <7> [250.719475] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [250.719767] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [250.720052] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000 <7> [250.720369] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000 <7> [250.720673] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000 <7> [250.720975] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [250.721263] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [250.721571] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000 <7> [250.721867] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000 <7> [250.722149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:268] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [250.722452] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [250.722749] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0 <7> [250.723057] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [250.723377] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [250.723677] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [250.723966] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [250.724257] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no <7> [250.724562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no <7> [250.724853] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no <7> [250.736453] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [250.741402] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [250.741747] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [250.742062] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [250.742697] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [250.743096] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 50000 kHz, VCO 0 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0 <7> [250.743444] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [250.744692] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [250.745826] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [250.746132] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [250.751555] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [250.755065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [250.755417] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [250.756075] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [250.756972] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.757300] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [250.757628] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.757931] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [250.758231] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [250.758585] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [250.758955] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1 <7> [250.759441] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A] <7> [250.759738] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B] <7> [250.760017] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A] <7> [250.760294] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B] <7> [250.760586] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C] <7> [250.760865] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C] <7> [250.761144] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [250.761474] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [250.761792] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4 <7> [250.762117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [250.762475] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A] <7> [250.762766] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [250.763189] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on <7> [250.763502] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [251.244587] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [251.244946] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [251.245354] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on <7> [251.245805] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [251.307575] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010 <7> [251.307888] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long <7> [251.308169] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10 <7> [251.308496] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A] <7> [251.457436] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [251.457789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [251.458323] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on <7> [251.458857] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [251.460701] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00 <7> [251.460754] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14 <7> [251.461636] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [251.462046] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [251.463380] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0 <7> [251.463661] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0 <7> [251.465116] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK <7> [251.465410] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [251.467324] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1 <7> [251.467612] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1 <7> [251.469761] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [251.470083] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4 <7> [251.470762] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [251.471200] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [251.471499] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [251.471814] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000 <7> [251.476430] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [251.476771] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A] <7> [251.488227] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1] <7> [251.488625] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A] <7> [251.489133] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0 <7> [251.489464] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [251.490361] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1] <7> [251.491306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <6> [251.491565] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS <7> [251.491668] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000 <7> [251.491957] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000 <7> [251.492258] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000 <7> [251.492624] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc. <7> [251.492638] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor <7> [251.492647] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0 <7> [251.492683] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no <7> [251.492967] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [251.494228] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [251.494571] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [251.495607] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:239:eDP-1] Same epoch counter 1 <7> [251.495658] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1] <7> [251.496007] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:248:DP-1] Same epoch counter 1 <7> [251.496049] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1] <7> [251.496417] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] Same epoch counter 6 <7> [251.496455] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2] <7> [251.496774] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1 <7> [251.515160] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [251.515724] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3 <7> [251.516284] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x4810 <7> [251.528428] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [251.528858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [251.569285] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:268] from all active usage due to RMFB ioctl <7> [251.569411] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:268] is removed <7> [251.569518] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0 <7> [251.569898] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [251.570216] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [251.570543] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [251.570845] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [251.571138] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0 <7> [251.571462] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0 <7> [251.571764] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0 <7> [251.572065] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0 <7> [251.587919] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A] <7> [251.605728] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985 <7> [251.606069] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5,wm6,wm7,twm, swm, stwm <7> [251.606381] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 <7> [251.606689] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 <7> [251.606997] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 <7> [251.607307] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1 <7> [251.607644] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446 <7> [251.607948] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446 <7> [251.608237] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446 <7> [251.608873] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1 <7> [251.609169] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A] <6> [251.622532] [IGT] i915_pm_rpm: exiting, ret=0 <6> [251.638515] Console: switching to colour frame buffer device 400x112

<7> [245.334864] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]

<7> [245.334912] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [245.335879] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [245.336177] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [245.336482] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [245.336767] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [245.337095] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [245.337109] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [245.337117] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [245.337150] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [245.337480] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [245.338577] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [245.338882] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [245.339923] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :

<7> [245.339959] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [245.339971] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [245.340160] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]

<7> [245.340196] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [245.340554] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected

<7> [245.340735] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]

<7> [245.340769] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [245.341098] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [245.341268] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [245.341301] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [245.341641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [245.358786] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]

<7> [245.358833] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [245.359211] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected

<7> [245.360258] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]

<7> [245.360299] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [245.360726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [245.361913] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [245.361949] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [245.362286] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [245.363729] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]

<7> [245.363769] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [245.364672] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [245.364969] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [245.365262] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [245.365576] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [245.365914] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [245.365928] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [245.365936] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [245.365972] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [245.366254] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [245.367324] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [245.367635] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [245.368677] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :

<7> [245.368714] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [245.368726] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa

<7> [245.368782] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]

<7> [245.368815] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [245.369132] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected

<7> [245.369194] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]

<7> [245.369225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [245.369564] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected

<7> [245.369627] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]

<7> [245.369658] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [245.369978] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected

<7> [246.459837] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)

<7> [246.460200] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 1, found 0)

<7> [246.460525] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)

<7> [246.460834] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 4, found 0)

<7> [246.461128] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0)

<7> [246.461437] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)

<7> [246.461738] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)

<7> [246.462027] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)

<7> [246.462313] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3316, found 0)

<7> [246.462615] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)

<7> [246.462906] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0)

<7> [246.463190] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)

<7> [246.463509] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)

<7> [246.463805] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)

<7> [246.464088] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1816, found 0)

<7> [246.464385] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)

<7> [246.464677] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0)

<7> [246.464960] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0)

<7> [246.465240] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0)

<7> [246.465540] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)

<7> [246.465830] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3316, found 0)

<7> [246.466110] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)

<7> [246.466404] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0)

<7> [246.466692] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)

<7> [246.466975] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)

<7> [246.467256] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)

<7> [246.467575] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0)

<7> [246.467866] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)

<7> [246.468149] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0)

<7> [246.468463] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0)

<7> [246.468764] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0)

<7> [246.469057] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)

<7> [246.469432] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)

<7> [246.469735] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)

<7> [246.470029] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)

<7> [246.470315] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 361310, found 0)

<7> [246.470619] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 361310, found 0)

<7> [246.470916] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)

<7> [246.471206] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [246.471508] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0

<7> [246.471842] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0

<7> [246.472228] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0

<7> [246.472554] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0

<7> [246.472854] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [246.473131] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [246.473425] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [246.473706] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [246.473982] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0

<7> [246.474273] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [246.474585] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0

<7> [246.474881] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0

<7> [246.475234] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [246.475542] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz

<7> [246.475842] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0

<7> [246.476153] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset]

<7> [246.477719] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [246.478044] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [246.478359] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [246.478672] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [246.478975] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [246.479275] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [246.479594] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [246.479895] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [246.491382] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [246.700410] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0

<7> [246.700964] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [246.704582] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off

<7> [246.704927] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [246.705263] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [246.710873] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [246.711180] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [246.711468] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [246.711813] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [246.732064] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [246.732392] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [246.732674] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20

<7> [246.733026] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [246.758405] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [246.758731] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [246.759042] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A]

<7> [246.759372] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [246.759681] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [246.760051] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [246.760350] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [246.760633] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30

<7> [246.760940] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [246.760971] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]

<7> [246.761267] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [246.761739] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [246.762047] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [246.762364] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [246.762662] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [246.762950] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [246.763226] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [246.763525] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [246.763840] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [246.764141] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [246.764451] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [246.764817] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [246.765315] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [246.765659] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [246.765962] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [246.767519] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [246.768190] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [246.769084] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.769411] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [246.769708] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.770005] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [246.770299] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.770628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [246.770966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [246.771273] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [246.771617] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [246.773050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [246.773735] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [246.774644] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.774961] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [246.775253] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.775585] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [246.775889] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.776199] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [246.776553] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [246.776854] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [246.777143] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [246.972373] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [246.973579] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [246.976992] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [246.977879] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.978199] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [246.978512] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.978819] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [246.979108] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.979418] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [246.979709] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [246.980285] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [246.980673] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [246.981007] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [246.981288] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [246.985563] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<6> [247.082295] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state

<7> [247.117735] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [247.122361] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [247.122707] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [247.123023] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [247.123472] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [247.124772] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 50000 kHz, VCO 0 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [247.125109] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [247.125586] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [247.126720] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [247.127028] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [247.134040] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [247.134619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [247.134961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [247.135645] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [247.136533] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.136849] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [247.137156] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.137491] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [247.137802] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.138107] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [247.138442] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [247.138743] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [247.139023] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [247.140104] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [247.141327] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [247.143716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [247.144576] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.144903] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [247.145212] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.145538] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [247.145840] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.146143] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [247.146440] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [247.147816] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [247.148188] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.148546] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [247.148838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [247.149513] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [247.154411] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<7> [247.178590] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [247.184632] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [247.184979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [247.185307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [247.185845] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [247.186494] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 50000 kHz, VCO 0 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [247.186803] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [247.187202] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [247.188320] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [247.188660] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [247.196582] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [247.197104] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [247.197541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [247.198230] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [247.199134] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.199528] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [247.199837] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.200141] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [247.200467] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [247.200791] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [247.201093] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [247.202136] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [247.202518] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [247.364647] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x08000001 PP_CONTROL: 0x00000060

<7> [247.372397] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [247.372795] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068

<7> [247.373081] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled

<6> [247.415612] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0

<4> [247.415631] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)

<4> [247.415637] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000

<7> [247.434949] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [247.435289] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [247.435575] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [247.435872] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [247.581229] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [247.581573] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [247.581854] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [247.582137] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [247.582986] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [247.583003] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [247.583012] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [247.583088] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [247.583430] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [247.584875] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [247.585159] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [247.587395] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:239:eDP-1] Same epoch counter 1

<7> [247.587454] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [247.588236] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:248:DP-1] Same epoch counter 1

<7> [247.588275] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [247.588655] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] Same epoch counter 6

<7> [247.588694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [247.589032] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1

<7> [247.589081] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [247.590011] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [247.590293] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [247.590593] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [247.590871] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [247.591183] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [247.591195] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [247.591204] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [247.591240] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [247.591530] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [247.592633] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [247.592914] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [247.595647] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:239:eDP-1] Same epoch counter 1

<7> [247.595698] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [247.596069] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:248:DP-1] Same epoch counter 1

<7> [247.596107] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [247.596481] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] Same epoch counter 6

<7> [247.596517] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [247.596859] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1

<7> [250.636469] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off

<7> [250.636995] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [250.637324] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [250.637690] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [250.638037] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.638364] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [250.639517] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [250.639508] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [250.639813] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [250.640109] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [250.640326] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device

<7> [250.640435] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [250.642533] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [250.643389] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.643700] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [250.643990] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.644284] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [250.644596] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.644898] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [250.645178] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0

<7> [250.645669] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1

<7> [250.645993] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.646315] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9

<7> [250.646610] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08

<7> [250.651384] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended

<7> [250.691452] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)

<7> [250.691847] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz

<7> [250.692158] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24

<7> [250.692470] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000

<7> [250.692753] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no

<7> [250.693032] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long

<7> [250.693314] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0

<7> [250.693630] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]

<7> [250.693914] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)

<7> [250.694215] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1)

<7> [250.694545] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)

<7> [250.694856] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4)

<7> [250.695150] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288)

<7> [250.695550] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)

<7> [250.695846] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)

<7> [250.696130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)

<7> [250.696469] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316)

<7> [250.696770] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)

<7> [250.697073] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316)

<7> [250.697477] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)

<7> [250.697776] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)

<7> [250.698068] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)

<7> [250.698380] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816)

<7> [250.698674] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)

<7> [250.698957] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816)

<7> [250.699241] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802)

<7> [250.699566] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807)

<7> [250.699881] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)

<7> [250.700176] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316)

<7> [250.700481] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)

<7> [250.700779] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316)

<7> [250.701068] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)

<7> [250.701365] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)

<7> [250.701663] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)

<7> [250.701962] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816)

<7> [250.702270] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)

<7> [250.702594] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816)

<7> [250.702892] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802)

<7> [250.703184] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807)

<7> [250.703522] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)

<7> [250.703817] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)

<7> [250.704100] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)

<7> [250.704412] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)

<7> [250.704717] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310)

<7> [250.705022] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310)

<7> [250.705327] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)

<7> [250.705634] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset

<7> [250.705996] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1

<7> [250.706387] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985

<7> [250.706669] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39

<7> [250.706950] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm

<7> [250.707244] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [250.707570] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0

<7> [250.707862] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0

<7> [250.708144] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1

<7> [250.708528] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [250.708822] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446

<7> [250.709109] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446

<7> [250.709448] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz)

<7> [250.709746] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)

<7> [250.710090] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change

<7> [250.710438] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz

<7> [250.710747] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1

<7> [250.711037] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0

<7> [250.711321] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0

<7> [250.711629] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]

<7> [250.711919] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB

<7> [250.712209] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0

<7> [250.712529] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [250.712832] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [250.713129] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [250.713435] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [250.713731] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64

<7> [250.714019] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [250.714299] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [250.714637] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [250.714938] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2

<7> [250.715240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [250.715557] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa

<7> [250.715851] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [250.716142] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa

<7> [250.716450] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa

<7> [250.716747] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310

<7> [250.717032] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0

<7> [250.717313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [250.717628] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [250.717936] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [250.718239] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [250.718555] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [250.718847] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [250.719138] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000

<7> [250.719475] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [250.719767] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [250.720052] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000

<7> [250.720369] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000

<7> [250.720673] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000

<7> [250.720975] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [250.721263] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [250.721571] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000

<7> [250.721867] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000

<7> [250.722149] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:268] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [250.722452] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [250.722749] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0

<7> [250.723057] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [250.723377] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [250.723677] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [250.723966] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [250.724257] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no

<7> [250.724562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no

<7> [250.724853] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no

<7> [250.736453] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device

<7> [250.741402] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9

<7> [250.741747] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00

<7> [250.742062] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [250.742697] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [250.743096] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 50000 kHz, VCO 0 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0

<7> [250.743444] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [250.744692] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [250.745826] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [250.746132] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [250.751555] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed

<7> [250.755065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [250.755417] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [250.756075] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [250.756972] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.757300] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [250.757628] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.757931] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [250.758231] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [250.758585] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.

<7> [250.758955] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1

<7> [250.759441] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]

<7> [250.759738] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]

<7> [250.760017] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]

<7> [250.760294] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]

<7> [250.760586] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]

<7> [250.760865] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]

<7> [250.761144] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [250.761474] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [250.761792] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4

<7> [250.762117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [250.762475] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]

<7> [250.762766] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [250.763189] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on

<7> [250.763502] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [251.244587] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [251.244946] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [251.245354] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on

<7> [251.245805] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063

<7> [251.307575] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010

<7> [251.307888] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long

<7> [251.308169] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10

<7> [251.308496] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]

<7> [251.457436] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [251.457789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [251.458323] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on

<7> [251.458857] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [251.460701] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00

<7> [251.460754] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14

<7> [251.461636] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [251.462046] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [251.463380] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0

<7> [251.463661] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0

<7> [251.465116] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK

<7> [251.465410] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [251.467324] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1

<7> [251.467612] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1

<7> [251.469761] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [251.470083] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4

<7> [251.470762] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [251.471200] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [251.471499] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [251.471814] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000

<7> [251.476430] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [251.476771] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]

<7> [251.488227] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]

<7> [251.488625] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]

<7> [251.489133] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0

<7> [251.489464] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [251.490361] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]

<7> [251.491306] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<6> [251.491565] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS

<7> [251.491668] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000

<7> [251.491957] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000

<7> [251.492258] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000

<7> [251.492624] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.

<7> [251.492638] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor

<7> [251.492647] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0

<7> [251.492683] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no

<7> [251.492967] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [251.494228] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [251.494571] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [251.495607] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:239:eDP-1] Same epoch counter 1

<7> [251.495658] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]

<7> [251.496007] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:248:DP-1] Same epoch counter 1

<7> [251.496049] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]

<7> [251.496417] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] Same epoch counter 6

<7> [251.496455] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]

<7> [251.496774] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] Same epoch counter 1

<7> [251.515160] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [251.515724] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3

<7> [251.516284] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x4810

<7> [251.528428] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3

<7> [251.528858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [251.569285] i915 0000:00:02.0: [drm:drm_mode_rmfb_work_fn] Removing [FB:268] from all active usage due to RMFB ioctl

<7> [251.569411] i915 0000:00:02.0: [drm:atomic_remove_fb] Disabling [PLANE:31:plane 1A] because [FB:268] is removed

<7> [251.569518] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0

<7> [251.569898] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [251.570216] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [251.570543] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [251.570845] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [251.571138] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0

<7> [251.571462] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0

<7> [251.571764] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0

<7> [251.572065] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0

<7> [251.587919] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]

<7> [251.605728] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985

<7> [251.606069] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm

<7> [251.606381] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0

<7> [251.606689] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0

<7> [251.606997] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0

<7> [251.607307] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1

<7> [251.607644] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446

<7> [251.607948] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446

<7> [251.608237] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446

<7> [251.608873] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1

<7> [251.609169] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]

<6> [251.638515] Console: switching to colour frame buffer device 400x112

Results for igt@i915_pm_rpm@basic-pci-d3-state