Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-g2741053c5 (x86_64) (Linux: 6.5.0-rc7-linus-v6.5-rc7-g706a74159504+ x86_64) |
| Out |
Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa3f/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (1.655s) |
| Err |
Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (1.655s) |
| Dmesg |
<6> [212.501060] Console: switching to colour dummy device 80x25
<6> [212.501376] [IGT] i915_pm_rpm: executing
<7> [212.526264] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [212.530099] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [212.530239] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [212.531446] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.532840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.533883] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [212.534372] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [212.534475] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [212.535667] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.537287] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.538470] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [212.538942] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [212.539024] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [212.539931] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.541232] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.542414] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [212.542985] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [212.543064] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [212.543949] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.545342] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.546558] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [212.546983] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4]
<7> [212.547062] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [212.547955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.549216] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.550388] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4] disconnected
<7> [212.550983] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5]
<7> [212.551062] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [212.551933] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.553195] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.554175] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5] disconnected
<7> [212.609020] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [212.609161] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [212.610420] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.611825] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.612892] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [212.616203] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [212.616310] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [212.617458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.618991] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.620025] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [212.623256] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [212.623364] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [212.624590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.626014] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.627041] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [212.630256] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [212.630358] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [212.631543] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.632935] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.633948] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [212.637288] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4]
<7> [212.637390] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [212.638541] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.639895] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.640898] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4] disconnected
<7> [212.643999] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5]
<7> [212.644100] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [212.645214] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.646682] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.647653] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5] disconnected
<7> [212.651926] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [212.652031] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [212.653131] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.654299] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.655314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [212.655482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [212.655675] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [212.656635] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.657903] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.659141] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [212.659333] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [212.659429] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [212.660394] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.661726] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.662668] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [212.662821] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [212.662895] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [212.663801] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.665266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.666379] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [212.666634] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4]
<7> [212.666730] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [212.667652] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.668847] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.669816] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-4] disconnected
<7> [212.669969] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5]
<7> [212.670045] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [212.670913] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [212.672162] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [212.673380] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:282:DP-5] disconnected
<7> [213.680804] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [213.684972] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [213.687254] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [213.689249] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.691233] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [213.693002] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [213.694252] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [213.695437] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [213.698832] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [213.727065] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [213.727870] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [213.729132] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [213.730396] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [213.731552] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [213.732708] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [213.733861] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [213.735438] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [213.736637] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [213.747921] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.748867] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.757215] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [213.760015] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [213.764103] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [213.764099] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [213.766278] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [213.765888] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [213.767930] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [213.769860] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [213.770592] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [213.771658] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [213.772990] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.774372] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [213.775548] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.776601] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.777864] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [213.780301] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [213.782115] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [213.782107] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [213.785984] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [213.787687] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [213.789261] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.791183] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [213.793043] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [213.794149] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [213.795120] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [213.796791] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [213.824592] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [213.825216] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [213.826479] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [213.827668] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [213.828737] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [213.830172] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [213.831281] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [213.832920] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [213.834166] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [213.845613] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.846780] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.857572] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [213.861933] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [213.864298] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [213.865288] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [213.867224] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [213.869536] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [213.872694] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [213.874146] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [213.875981] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.877900] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [213.879436] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [213.880698] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [213.881958] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 5
<7> [213.883064] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [213.884263] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [213.911197] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [213.912226] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [213.913542] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [213.914690] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [213.915726] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [213.916813] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [213.917942] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [213.919551] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [213.920665] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [213.932437] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.933733] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.943040] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [213.947248] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [213.949038] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [213.949973] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [213.950981] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [213.952339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.953903] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [213.954895] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [213.955870] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [213.957093] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [213.958210] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [213.960319] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [213.959989] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [213.960270] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [213.961369] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [213.963068] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [213.964897] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [213.966357] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [213.967646] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [213.968746] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [213.969755] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [213.996250] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [213.997058] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [213.998287] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [213.999640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.000745] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.001901] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.003021] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.004553] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.005809] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.017338] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.018609] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.025034] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.026817] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.028287] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.028954] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.031600] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.032852] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.034181] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.035049] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.036652] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.038438] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.039945] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.040658] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.041116] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.041604] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.041910] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [214.067621] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.068248] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.069581] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.070696] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.071764] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.072871] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.073933] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.075233] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.076426] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.087959] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.089106] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.094232] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.096067] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.097549] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.098254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.099208] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [214.100271] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.101664] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [214.102648] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.103549] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.104609] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.105563] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.106411] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [214.106389] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [214.106869] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.107656] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.109024] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.110771] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.111929] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.112876] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.113756] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.114718] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.141124] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.141885] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.143109] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.144264] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.145374] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.146597] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.147525] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.148962] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.150164] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.162011] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.163224] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.170104] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.172558] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.175944] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.176585] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.178064] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.179421] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.181216] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.182378] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.184067] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.185975] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.187277] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.188775] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.190021] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.191136] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.192075] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [214.217764] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.218380] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.219667] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.220854] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.222013] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.223473] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.224619] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.225901] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.227301] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.238807] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.239975] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.246005] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.247775] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.249367] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.250246] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.251176] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [214.252268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.253863] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [214.254986] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.256069] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.257058] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.258074] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.259468] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.260049] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [214.260980] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.262611] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.263744] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.264574] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.265292] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.266216] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.267081] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.293412] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.294259] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.295548] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.296648] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.297709] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.298850] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.299886] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.301292] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.302738] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.314209] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.315369] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.321758] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.323708] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.325128] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.325931] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.327363] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.328638] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.330078] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.330925] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.332316] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.334149] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.335423] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.336656] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.337679] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.338684] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.339305] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:273:DP-4] Same epoch counter 1
<7> [214.339412] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [214.366139] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.366954] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.368189] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.369359] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.370542] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.371708] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.372778] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.374190] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.375536] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.387198] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.388399] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.394943] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.396660] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.398084] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.398738] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.400167] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.401444] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.403083] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.403924] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.405339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.407121] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.409314] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:282:DP-5] Same epoch counter 1
<7> [214.409541] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [214.419747] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.420990] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.422167] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.423324] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.449940] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.450613] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.451802] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.453014] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.454114] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.455138] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.456333] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.457748] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.458855] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.470394] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.471604] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.477981] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.479740] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.481152] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.481782] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.482972] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.484291] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.485864] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.486667] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.488086] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.489819] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.491195] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.492389] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.493402] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.494440] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.495232] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [214.495334] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [214.520943] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.521632] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.522816] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.523984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.525065] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.526094] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.527181] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.528599] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.529863] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.541412] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.542612] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.548956] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.550687] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.552100] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.552716] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.553932] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.555240] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.556841] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.557745] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.559125] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.560875] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.562220] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.563378] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.564516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.565308] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.565972] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 5
<7> [214.566075] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [214.591715] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.592313] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.593576] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.594771] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.595835] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.596830] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.597996] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.599361] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.600639] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.612200] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.613358] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.619967] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.621575] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.623021] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.623777] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.625078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.626333] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.627963] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.628845] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.630261] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.632067] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.633375] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.634625] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.635523] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.636455] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.637261] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [214.637366] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [214.662980] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.663692] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.664817] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.665978] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.667066] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.668090] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.669261] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.670674] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.671727] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.683252] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.684437] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.690784] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.692723] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.694144] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.694842] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.696332] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.697668] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.699120] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.699971] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.701365] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.703147] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.704400] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.705668] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.706645] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.707613] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.708229] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [214.708333] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [214.733922] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.734607] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.735786] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.736958] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.738044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.739098] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.740291] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.741766] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.742836] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.754633] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.755759] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.761157] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.763029] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.764580] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.765101] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.766390] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.767634] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.768988] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.769950] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.771331] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.773130] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.774410] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.775683] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.776762] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.777750] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.778369] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:273:DP-4] Same epoch counter 1
<7> [214.778471] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [214.804097] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [214.804851] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [214.806056] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [214.807169] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [214.808255] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [214.809406] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [214.810555] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [214.812025] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [214.813119] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [214.824744] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [214.825918] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [214.831226] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [214.833120] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [214.834672] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [214.835192] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [214.836485] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [214.837721] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [214.839087] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [214.840121] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [214.841620] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [214.843270] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [214.844478] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [214.845682] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [214.846756] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [214.847727] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [214.848347] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:282:DP-5] Same epoch counter 1
<6> [214.864754] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [215.643571] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [215.656795] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [215.657414] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [215.658813] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [215.660052] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [215.661183] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [215.662240] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [215.663241] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [215.664419] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [215.665749] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [215.677063] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.678231] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.684575] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [215.686470] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [215.689433] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [215.690625] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [215.691772] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [215.692906] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.694334] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [215.695337] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.696270] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.697249] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [215.698397] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [215.698933] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [215.700330] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [215.701227] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [215.702726] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.704411] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [215.705967] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [215.707096] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [215.708182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [215.709216] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [215.735621] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [215.736222] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [215.737472] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [215.738728] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [215.739787] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [215.740774] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [215.741791] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [215.743133] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [215.744379] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [215.755906] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.757057] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.762274] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [215.764269] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [215.766001] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [215.766741] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [215.767990] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [215.769705] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.771763] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [215.773383] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.774770] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.776383] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [215.778261] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [215.780328] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [215.780259] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [215.780311] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [215.781541] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [215.783417] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.786238] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [215.787997] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [215.789644] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [215.791220] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [215.793045] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [215.819882] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [215.820590] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [215.821713] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [215.822769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [215.824024] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [215.825113] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [215.826253] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [215.827770] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [215.828924] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [215.844011] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.845228] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.850132] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [215.852396] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [215.854143] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [215.854788] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [215.855984] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [215.857055] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [215.858558] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [215.859364] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [215.861174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.862915] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [215.864113] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [215.865164] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [215.866300] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [215.867369] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [215.868298] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [215.893945] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [215.894664] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [215.895948] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [215.897097] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [215.898158] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [215.899192] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [215.900195] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [215.901569] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [215.902761] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [215.914101] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.915259] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.921432] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [215.923352] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [215.924856] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [215.925586] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [215.926456] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [215.927684] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.929021] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [215.929955] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.930839] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.931777] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [215.932721] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [215.933986] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [215.933956] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [215.934037] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [215.934848] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [215.936219] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [215.937885] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [215.939056] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [215.940008] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [215.940986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [215.942019] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [215.968636] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [215.969242] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [215.970475] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [215.971686] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [215.972763] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [215.973773] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [215.974856] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [215.976230] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [215.977444] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [215.989136] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [215.990321] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [215.996216] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [215.998425] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.000010] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.000587] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.001805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.002830] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.004332] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.005373] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [216.006940] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.008800] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.010140] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.011245] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.012348] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.013411] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.014230] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 5
<7> [216.014337] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [216.039969] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.040719] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.041326] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.041856] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.042332] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.042993] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.043794] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.044968] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.046064] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [216.057926] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.059165] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.065263] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.067605] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.069066] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.069656] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.070927] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.071979] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.073035] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.074047] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [216.075449] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.076992] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.078196] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.079340] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.080479] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.081714] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.082477] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [216.108160] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.108908] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.110188] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.111386] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.112525] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.113482] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.114592] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.115911] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.117117] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [216.128348] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.129574] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.135327] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.137297] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.138972] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.139671] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.140586] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [216.141671] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.143113] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [216.144189] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.145265] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.146270] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.147466] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.149135] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [216.150426] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.151604] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [216.153165] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.154882] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.156078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.157251] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.158347] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.159383] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.185907] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.186646] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.187793] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.188781] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.189823] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.191031] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.192142] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.193391] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.194687] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [216.206286] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.207480] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.214019] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.215835] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.217347] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.218045] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.219567] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.220792] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.222275] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.223252] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [216.224744] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.226434] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.227966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.229097] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.230195] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.231245] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.232006] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [216.232113] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [216.257729] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.258335] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.259616] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.260756] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.261822] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.262816] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.264003] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.265371] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.266698] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [216.278259] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.279449] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.286031] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.287811] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.289265] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.289926] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.291384] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.292608] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.294069] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.294922] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [216.296344] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.298183] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.299744] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.300788] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.301683] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.302671] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.303286] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:273:DP-4] Same epoch counter 1
<7> [216.303393] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [216.329057] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.329801] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.331010] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.332146] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.333239] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.334259] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.335210] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.336600] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.337668] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [216.349400] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.350622] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.356973] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.358792] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.360310] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.360976] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.362254] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.363632] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [216.365097] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [216.366058] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT1: GUC: communication disabled
<7> [216.367482] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.369244] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [216.370486] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [216.371759] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [216.372905] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [216.373910] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [216.374578] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:282:DP-5] Same epoch counter 1
<7> [216.463605] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [216.465571] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [216.466746] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [216.467852] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [216.468937] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [216.470287] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [216.470679] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [216.471335] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [216.471842] i915 0000:00:02.0: [drm:icl_display_core_init [i915]] Unknown memory configuration; disabling address buddy logic.
<7> [216.481030] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.481388] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [216.489169] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [216.494097] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT1: GUC: communication enabled
<7> [216.498007] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [216.500308] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [216.502189] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.503762] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.504870] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [216.505009] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [216.505962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.507266] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.508305] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 5
<7> [216.508424] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [216.509316] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.510705] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.511715] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [216.511827] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [216.512692] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.513995] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [216.516593] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [216.516738] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-4]
<7> [216.516826] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [216.518182] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:273:DP-4] Same epoch counter 1
<7> [216.518259] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:282:DP-5]
<7> [216.518929] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:282:DP-5] Same epoch counter 1
<6> [216.519983] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [216.522425] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [216.523290] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.524164] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [216.524675] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.525088] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<6> [216.526394] [IGT] i915_pm_rpm: exiting, ret=0
<7> [216.530757] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [216.531626] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.532459] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [216.532959] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.533417] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<6> [216.534650] Console: switching to colour frame buffer device 128x48
<7> [216.536337] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [216.537150] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [216.537986] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [216.538438] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [216.538872] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
|