Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g74c7773be (x86_64) (Linux: 6.5.0-rc6-linus-v6.5-rc6-g2ccdd1b13c59+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.026s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.026s)
Dmesg
<6> [283.025728] Console: switching to colour dummy device 80x25
<6> [283.026497] [IGT] kms_force_connector_basic: executing
<7> [283.350733] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [283.351443] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [283.351703] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [283.352373] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [283.352384] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.352413] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.352633] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.352823] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.353251] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.353448] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.353823] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.354011] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.354018] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.354254] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.355797] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.355805] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.355995] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.356211] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.356309] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.356342] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.356566] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.356752] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.357113] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.357432] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.357931] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.358291] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.358301] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.358606] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.360442] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.360453] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.360742] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.361034] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.361278] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.361311] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.361619] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.361907] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.362468] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.362756] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.363274] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.363564] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.363573] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.363861] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.365698] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.365709] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.365998] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.366307] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<6> [283.367459] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [283.367822] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 2 or reprobing
<7> [283.367837] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.367876] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from disconnected to connected
<7> [283.368260] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.368582] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.369091] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.369450] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.369475] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.369764] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.371730] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.371757] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.372223] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [283.372262] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [283.372274] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [283.372285] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [283.372296] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [283.372305] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [283.372403] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.372680] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.372960] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.373513] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.373799] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.373819] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.374091] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.375921] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.375940] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.376362] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [283.376402] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [283.376412] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [283.376420] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [283.376429] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [283.376438] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [283.376800] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [283.376847] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.376938] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [283.376948] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [283.377238] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [283.377251] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [283.377266] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [283.377276] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [283.377291] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [283.377320] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [283.377330] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [283.377339] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [283.377348] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [283.377357] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [283.377366] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [283.377617] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:65:VGA-1] EDID override set
<7> [283.377669] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.377753] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD monitor IGT
<7> [283.377762] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:65:VGA-1] ELD size 24, SAD count 0
<7> [283.377771] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 64
<7> [283.377992] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [283.378003] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [283.378017] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [283.378043] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [283.378052] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [283.378060] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [283.378069] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [283.378077] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [283.378312] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [283.378366] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.378659] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.378945] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.379527] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.379801] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.379820] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.380090] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.381910] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.381929] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.382371] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [283.382383] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [283.382398] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [283.382409] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [283.382423] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] probed modes :
<7> [283.382456] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [283.382473] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [283.382481] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [283.382489] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [283.382497] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [283.382794] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 2 to 0 or reprobing
<7> [283.382803] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.382835] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.383135] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.383451] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.383918] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.384274] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.384773] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.385045] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.385055] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.385401] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.387349] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.387361] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.387634] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.387910] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from connected to disconnected
<7> [283.387956] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.388122] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:65:VGA-1] EDID changed, epoch counter 66
<7> [283.388273] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.388307] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.388624] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.388914] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.389564] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.389857] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.390390] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.390685] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.390695] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.390985] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.392833] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.392846] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.393190] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.393483] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<6> [283.394686] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [283.394972] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [283.395845] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [283.395859] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [283.395903] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [283.395916] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [283.396035] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [283.396065] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [283.396132] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [283.396212] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [283.396222] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [283.396317] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [283.396345] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [283.396552] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:LVDS-1] EDID override reset
<7> [283.396596] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [283.396626] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [283.396635] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [283.396718] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [283.396745] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [283.397021] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [283.397030] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.397061] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.397419] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.397711] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.398237] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.398527] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.399026] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.399331] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.399342] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.399633] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.401582] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.401593] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.401865] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.402192] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.402303] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.402335] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.402642] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.402929] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.403481] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.403768] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.404228] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.404517] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.404526] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.404813] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.406664] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.406674] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.406947] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.407275] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.407518] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:65:VGA-1] EDID override reset
<7> [283.407565] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.407598] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.407907] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.408212] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.408723] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.409010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.409557] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.409847] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.409856] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.410116] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.411595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.411603] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.411798] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.411988] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.412336] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [283.412348] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [283.412383] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [283.465193] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [283.481235] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.481248] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.481524] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [283.497242] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.497255] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [283.497540] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [283.497659] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [283.497690] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [283.548840] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [283.565211] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.565222] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.565422] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [283.581209] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.581218] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [283.581416] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [283.581618] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:68:HDMI-A-1] EDID override reset
<7> [283.581654] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [283.581675] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [283.632463] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [283.648214] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.648225] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.648422] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [283.664198] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.664207] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [283.664407] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [283.664632] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:76:DP-1] EDID override reset
<7> [283.664668] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [283.664689] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [283.664901] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [283.665111] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [283.665118] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [283.665140] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [283.665993] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.666344] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [283.666858] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.667185] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.667197] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.667474] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [283.669057] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.669067] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [283.669301] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [283.669427] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [283.669461] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [283.669864] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.670050] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [283.670475] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.670664] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.670670] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.670857] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [283.672298] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.672305] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [283.672497] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [283.672676] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:81:HDMI-A-2] EDID override reset
<7> [283.672707] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [283.672728] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [283.673116] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.673382] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [283.673756] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.673944] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.673949] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.674132] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [283.675603] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.675611] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [283.675803] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [283.676033] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [283.676040] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [283.676061] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [283.676509] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.676698] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [283.677071] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.677305] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.677315] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.677572] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [283.679092] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.679100] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [283.679339] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [283.679444] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [283.679475] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [283.679890] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.680076] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [283.680482] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.680670] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.680676] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.680858] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [283.682317] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.682324] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [283.682516] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [283.682686] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:85:HDMI-A-3] EDID override reset
<7> [283.682716] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [283.682737] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [283.683131] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.683387] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [283.683810] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.683998] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.684004] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.684239] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [283.685710] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.685717] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [283.685907] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [283.686081] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:89:DP-2] EDID override reset
<7> [283.686110] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [283.686131] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [283.686384] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [283.686609] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:93:DP-3] EDID override reset
<7> [283.686638] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [283.686659] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [283.686865] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<6> [283.687985] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [283.688226] [drm:status_store] [CONNECTOR:65:VGA-1] force updated from 0 to 0 or reprobing
<7> [283.688241] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.688280] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.688552] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.688742] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.689112] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.689344] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.689719] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.689908] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.689915] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.690101] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.691688] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.691697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.691887] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.692086] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.692265] [drm:status_store] [CONNECTOR:61:LVDS-1] force updated from 0 to 0 or reprobing
<7> [283.692277] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [283.692315] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [283.692326] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [283.692417] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [283.692436] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [283.692501] [drm:status_store] [CONNECTOR:68:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [283.692507] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [283.692526] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [283.744419] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [283.760250] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.760267] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.760566] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [283.776225] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.776238] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [283.776526] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [283.776685] [drm:status_store] [CONNECTOR:81:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [283.776696] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [283.776728] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [283.777186] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.777407] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [283.777786] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.777975] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.777983] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.778202] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [283.779770] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.779779] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [283.779976] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [283.780074] [drm:status_store] [CONNECTOR:85:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [283.780081] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [283.780102] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [283.780546] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.780735] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [283.781109] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.781377] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.781387] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.781634] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [283.783134] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.783145] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [283.783427] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [283.783766] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [283.799275] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [283.799304] [drm:drm_client_modeset_probe]
<7> [283.799374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [283.799400] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [283.799408] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [283.799488] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [283.799507] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [283.799515] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [283.799534] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [283.799765] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [283.799955] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [283.800359] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.800596] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [283.800970] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [283.801193] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.801201] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.801451] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [283.803017] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [283.803026] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [283.803230] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [283.803482] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [283.803508] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [283.803528] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [283.855614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [283.871226] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.871237] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.871431] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [283.887211] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [283.887221] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [283.887422] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [283.887450] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [283.887471] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [283.887681] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [283.887702] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [283.887721] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [283.888123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.888334] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [283.888738] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [283.888928] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.888935] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.889120] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [283.890652] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [283.890660] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [283.890851] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [283.890874] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [283.890893] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [283.891261] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.891474] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [283.891849] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [283.892036] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.892042] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [283.892282] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [283.894242] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [283.894259] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [283.894571] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [283.894609] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [283.894642] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [283.894872] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [283.894899] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [283.894927] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [283.895187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<7> [283.895208] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [283.895214] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [283.895218] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [283.895222] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [283.895227] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [283.895233] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [283.895239] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [283.895245] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [283.895291] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [283.895312] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [283.895319] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [283.895327] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [283.895333] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [283.895370] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [283.915938] Console: switching to colour frame buffer device 170x48
Created at 2023-08-13 20:39:06