Result:
git-log-oneline igt_runner0 run0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-g74c7773be (x86_64) (Linux: 6.5.0-rc6-linus-v6.5-rc6-g2ccdd1b13c59+ x86_64) |
| Out |
Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: yes Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa3f/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 Subtest basic-rte: SUCCESS (1.579s) i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa3f/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 |
| Err |
Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.579s) |
| Dmesg |
<6> [114.117946] Console: switching to colour dummy device 80x25
<6> [114.117984] [IGT] i915_pm_rpm: executing
<6> [114.125693] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [114.125732] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [114.126096] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [114.126112] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.126696] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.127063] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [114.127138] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [114.127149] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.127281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.127622] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.127739] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [114.127798] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [114.127808] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.127907] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.128230] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.128343] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [114.128406] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [114.128416] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.128519] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.128840] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.128952] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [114.134347] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [114.134361] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.134509] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.134826] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.134947] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [114.135321] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [114.135331] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.135443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.135762] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.135875] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [114.136231] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [114.136241] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.136338] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.136667] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.136778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [114.137140] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [114.137150] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.137250] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.137589] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.137702] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [114.138171] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [114.138182] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.138277] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.138592] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.138705] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [114.138725] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [114.138735] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.138831] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.139141] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.139249] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [114.139269] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [114.139278] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.139384] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.139703] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.139814] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [114.139833] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [114.139843] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.139936] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.140252] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.140364] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [115.141249] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.145001] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.146602] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.146966] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.147101] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.147226] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.147347] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.147564] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.147808] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.147972] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.148123] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.148230] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.148386] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.172651] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.173002] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.173626] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.174204] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.175028] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.175602] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.176044] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.176631] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.180677] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.180904] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.184128] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.184752] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.185101] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.185180] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.185665] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.185791] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.185813] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.185918] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.186279] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [115.186234] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.186355] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.186378] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.186482] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.186809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.186933] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.186947] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.187052] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.187386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.187506] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.187521] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.188005] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.188892] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.189033] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.189165] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.189294] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.189427] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.189628] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.190002] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.190156] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.190316] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.190439] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.190584] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.215427] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.215556] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.215759] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.215973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.216423] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.216685] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.216896] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.217191] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.219099] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.219239] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.222358] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.222990] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.223164] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.223296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.223666] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.223819] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.223934] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.224040] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.224145] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.224256] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.224356] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.224474] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.224574] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.224679] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.225040] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.225459] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [115.225948] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.226068] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.226178] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.226284] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.226394] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.226571] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.226853] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.226987] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.227123] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.227215] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.227332] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.251874] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.252022] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.252263] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.252543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.252983] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.253273] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.253520] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.253845] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.255943] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.256090] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.259337] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.259948] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.260087] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.260220] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.260526] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.260693] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.260852] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.261005] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.261154] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.261300] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.261449] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.261579] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.262023] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.262165] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.262695] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.263407] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [115.263437] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.263587] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.263751] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.263904] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.264051] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.264195] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.264437] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.264715] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.264890] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.265067] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.265197] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.265353] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.290143] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.290298] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.290560] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.290819] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.291272] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.291557] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.291765] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.292074] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.294079] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.294224] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.297376] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.297985] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.298085] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.298434] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.298758] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.298781] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.298917] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.299262] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.299411] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.299636] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.299791] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.300096] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.300263] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.300432] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.300584] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.300737] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.300884] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.301024] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.301154] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.301607] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.301804] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [115.301762] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.302283] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.303162] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.303325] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.303487] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.303635] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.303780] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.304016] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.304277] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.304458] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.304638] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.304772] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.304929] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.328613] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.328745] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.328921] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.329109] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.329491] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.329714] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.329886] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.330131] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.331887] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.332019] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.335122] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.335746] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.335880] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.336013] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.336307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.336480] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.336637] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.336788] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.336934] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.337078] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.337216] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.337346] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.337797] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.337940] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.338461] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.339375] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.339546] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.339709] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.339787] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.339861] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.340031] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.340285] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.340638] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.340815] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.340995] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.341127] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.341285] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.366049] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.366187] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.366428] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.366672] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.367110] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.367382] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.367582] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.367881] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.369792] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.369925] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.373054] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.373682] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.373785] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.374145] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.374290] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.374309] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.374448] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.374801] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.374939] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.374961] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.375089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.375426] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.375562] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.375577] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.375704] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.376047] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.376183] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.376198] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.376324] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.376680] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.376816] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.376832] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.376958] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.377304] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.377446] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.377464] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.377931] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.378838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.379004] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.379158] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.379306] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.379457] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.379707] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.379998] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.380172] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.380352] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.380492] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.380651] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.440477] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [115.452736] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.453215] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.454187] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.455119] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.456197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.457117] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.457989] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.458658] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.460286] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.460398] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.463615] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.464236] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.464359] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.464527] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.464825] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.464977] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.465114] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.465250] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.465391] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.465513] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.465628] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.465735] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.466159] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.466276] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.466747] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.467344] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.467745] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.467869] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.468028] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [115.467990] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.468112] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.468308] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.468555] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.468703] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.468851] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.468957] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.469091] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.493901] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.494056] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.494307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.494592] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.495040] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.495356] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.495609] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.495927] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.498042] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.498194] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.501418] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.501928] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.502011] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.502129] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.502422] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.502566] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.502701] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.502829] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.502954] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.503075] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.503192] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.503306] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.503438] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.503565] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.503921] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.504314] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.504919] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.505072] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.505204] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.505332] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.505471] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.505675] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.505990] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.506147] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.506307] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.506430] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.506567] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.506660] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [115.531104] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.531167] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.531276] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.531418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.531715] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.531886] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.532005] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.532204] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.533848] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.533960] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.537051] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.537620] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.537692] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.538056] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.538180] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.538197] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.538302] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.538637] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.538761] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.538880] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.539034] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.539344] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.539571] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.539722] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.539855] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.539982] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.540107] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.540227] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.540339] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.540784] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.540910] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.541364] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.541973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.542408] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [115.542375] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.542566] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.542694] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.542814] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.543010] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.543282] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.543442] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.543596] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.543703] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.543835] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.568444] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.568516] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.568626] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.568751] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.569020] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.569169] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.569274] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.569552] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.571189] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.571298] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.574505] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.575087] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.575188] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.575324] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.575629] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.575767] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.575893] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.576016] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.576139] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.576259] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.576381] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.576487] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.576911] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.577030] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.577497] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.578077] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.578102] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.578509] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.578642] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.578766] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.578887] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.579084] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.579316] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.579477] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.579632] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.579739] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.579870] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.602581] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.602652] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.602768] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.602901] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.603186] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.603349] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.603477] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.603712] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.605365] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.605490] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.608580] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.609161] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.609221] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.609605] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.609730] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.609747] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.609854] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.610181] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.610298] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.610317] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.610430] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.610749] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.610869] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.610882] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.610985] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.611304] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.611434] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.611447] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.611553] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.611883] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.612002] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.612015] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.612117] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.612446] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.612567] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.612581] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.613065] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.613954] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.614101] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.614235] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.614362] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.614499] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.614702] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.614958] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.615116] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.615275] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.615394] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.615533] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.691823] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.692364] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.693306] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.694196] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.695457] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.696793] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.697778] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.698797] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.700425] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.700539] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.703743] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.704360] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.704499] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<6> [115.705153] [IGT] i915_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [115.705182] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [115.705278] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.705615] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.705789] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.705945] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.706090] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.706233] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.706378] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.706502] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.706618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.707105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.707246] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.707380] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.707394] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.707503] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.707652] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [115.707831] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.707950] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.708050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.708202] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.708522] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.708696] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.708855] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.709007] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.709154] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.709298] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.709448] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.709583] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.710033] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.710185] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.710230] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [115.710707] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.711279] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.711619] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.711752] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.711880] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.712009] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.712214] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.712498] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.712652] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.712811] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.712926] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.713066] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.737630] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.737724] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.737875] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.738039] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.738358] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.738564] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.738707] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.738925] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.740636] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.740767] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.743873] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.744503] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.744637] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.744770] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.745065] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.745226] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.745390] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.745542] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.745689] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.745830] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.745968] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.746098] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.746549] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.746691] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.747205] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.747692] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [115.747816] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.748120] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.748292] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.748460] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.748613] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.748756] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.749005] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.749301] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.749483] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.749665] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.749799] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.749959] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.774430] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.774538] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.774675] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.774825] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.775136] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.775321] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.775475] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.775686] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.777453] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.777562] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.780645] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.781230] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.781293] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.781667] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.781791] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.781808] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.781909] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.782234] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.782350] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.782517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.782680] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.782986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.783153] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.783313] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.783477] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.783628] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.783776] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.783917] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.784050] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.784503] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.784646] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.785155] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.785688] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.786067] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.786240] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.786404] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.786555] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.786699] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.786934] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.787242] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.787427] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.787614] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.787746] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.787912] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.812795] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.812862] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.812979] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.813114] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.813429] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.813602] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.813720] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.813918] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.815575] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.815690] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.818774] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.819339] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.819417] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.819782] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.819906] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.819922] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.820027] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.820347] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.820479] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.820492] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.820600] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.820930] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.821050] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.821062] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.821167] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.821500] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.821622] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.821639] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.821745] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.822056] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.822177] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.822190] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [115.822292] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.822620] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.822737] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.822749] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.822852] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.823179] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.823297] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.823310] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.823417] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.823744] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.823862] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.823877] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [115.824377] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [115.824947] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.825287] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.825429] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.825558] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.825682] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.825881] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [115.826129] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [115.826280] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.826441] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [115.826557] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [115.826697] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [115.903279] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [115.904179] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [115.905235] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [115.906178] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [115.907443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [115.908248] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [115.908913] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [115.909765] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [115.912000] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.912132] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.916290] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [115.916961] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [115.917192] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.917333] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.917653] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.917829] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.917989] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.918142] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.918292] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.918465] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.918611] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.918745] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.919205] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.919713] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [115.919850] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.920189] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.920330] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [115.920352] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<6> [115.920472] [IGT] i915_pm_rpm: exiting, ret=0
<7> [115.920495] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.920851] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.921003] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [115.921027] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [115.921198] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.921566] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.921705] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [115.921721] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [115.921848] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.922203] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [115.922342] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [115.922521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.922652] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.922936] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.923085] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.923218] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.923347] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.923500] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.923642] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.923764] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.923874] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.924302] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [115.924549] Console: switching to colour frame buffer device 128x48
<7> [115.924838] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [115.924959] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [115.925240] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [115.925394] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.925527] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [115.925655] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [115.925779] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [115.925909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [115.926027] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [115.926139] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [115.926573] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
|