Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g74c7773be (x86_64) (Linux: 6.5.0-rc6-linus-v6.5-rc6-g2ccdd1b13c59+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: yes
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x79/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xa3f/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.574s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.574s)
Dmesg
<6> [112.195350] Console: switching to colour dummy device 80x25
<6> [112.195445] [IGT] i915_pm_rpm: executing
<7> [112.198029] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [112.198953] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [112.198987] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [112.199244] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.199710] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.199948] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [112.200080] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [112.200102] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.200308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.200821] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.201063] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.201175] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [112.201190] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [112.201360] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.201805] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.201973] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [112.202052] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [112.202066] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [112.202205] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.202596] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.202761] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [112.210556] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [112.210577] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [112.210750] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.211124] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.211295] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [112.211844] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [112.211859] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.212004] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.212384] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.212556] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.213072] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [112.213086] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [112.213230] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.213619] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.213780] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [112.214300] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [112.214315] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [112.214476] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.214855] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.215019] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [112.215687] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [112.215701] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [112.215844] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.216201] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.216359] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [112.216402] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1]
<7> [112.216416] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [112.216549] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.216907] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.217065] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] disconnected
<7> [112.217094] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2]
<7> [112.217107] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [112.217250] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.217730] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.217890] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:DP-2] disconnected
<7> [112.217918] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [112.217931] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [112.218068] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [112.218454] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [112.218615] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [113.221624] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.224739] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.225373] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.225802] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.225939] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.226068] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.226194] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.226409] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.226808] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.226979] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.227143] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.227257] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.227600] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.253172] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.253656] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.254283] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.254978] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.255864] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.257150] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.257630] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.258598] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.262407] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.262597] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.266389] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.267298] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.267759] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.267991] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.268444] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.268664] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [113.268683] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.268781] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.268906] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [113.268928] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.269152] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [113.269281] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.269469] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.269782] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.269954] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.270115] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.270268] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.270444] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.270572] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.270684] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.270791] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.271216] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.271487] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.272455] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.273314] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.273469] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.273601] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.273734] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [113.273727] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.273848] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.274044] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.274539] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.274697] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.274853] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.274963] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.275145] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.300093] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.300267] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.300483] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.300704] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.301097] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.301583] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.301759] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.302205] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.304100] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.304233] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.307469] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.308000] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.308089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.308213] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.308485] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.308628] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.308759] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.308889] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.309017] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.309139] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.309257] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.309375] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.309801] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.309921] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.310406] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.310508] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [113.311011] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.311393] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.311523] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.311651] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.311776] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.311976] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.312173] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.312307] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.312473] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.312634] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.312747] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.312884] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.337659] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.337744] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.337888] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.338054] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.338411] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.338797] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.338947] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.339165] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.340887] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.341000] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.344566] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.345190] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.345252] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.345727] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.345869] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [113.345886] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.345994] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.346322] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.346523] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [113.346583] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.346742] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.347047] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.347232] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.347422] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.347591] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.347740] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.347884] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.348024] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.348157] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.348611] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.348766] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.348830] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [113.349279] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.349847] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.350189] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.350324] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.350462] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.350594] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.350798] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.351056] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.351212] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.351373] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.351488] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.351629] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.376410] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.376514] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.376681] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.376862] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.377216] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.377451] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.377622] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.377883] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.379762] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.379897] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.382990] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.383563] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.383668] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.383809] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.384108] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.384251] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.384391] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.384520] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.384646] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.384772] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.384890] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.385001] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.385437] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.385562] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.386021] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.386624] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.387017] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.387146] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.387276] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.387411] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.387614] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.387799] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.387934] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.388089] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.388249] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.388363] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.388540] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.413050] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.413131] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.413272] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.413453] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.413789] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.414095] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.414237] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.414615] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.416284] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.416402] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.419494] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.420077] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.420137] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.420505] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.420630] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [113.420649] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.420757] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.421117] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.421237] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [113.421251] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.421354] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.421695] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.421817] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [113.421830] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.421935] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.422261] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.422384] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [113.422400] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.422502] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.422816] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.422934] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [113.422946] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.423047] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.423363] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.423494] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [113.423506] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.423611] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.423935] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.424051] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [113.424063] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.424164] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.424498] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.424617] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [113.424631] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.425118] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.426006] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.426155] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.426289] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.426424] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.426550] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.426751] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.426986] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.427142] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.427301] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.427420] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.427557] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [113.488042] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [113.761141] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [113.773611] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.773830] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.774144] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.774515] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.775284] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.775790] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.776104] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.776614] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.779288] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.779438] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.782658] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.783242] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.783318] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.783425] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.783705] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.783848] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.783981] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.784111] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.784237] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.784359] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.784488] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.784604] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.785032] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.785201] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.785651] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [113.786072] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.786683] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.786833] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.786964] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.787095] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.787221] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.787428] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.787618] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.787750] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.787909] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.788069] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.788182] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.788321] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.812896] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.812985] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.813139] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.813310] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.813689] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.813897] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.814051] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.814289] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.816050] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.816166] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.819253] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.819826] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.819896] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.820264] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.820397] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [113.820414] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.820522] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.820849] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.820970] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [113.820991] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.821495] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.822054] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.822403] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.822538] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.822667] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.822792] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.822999] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.823258] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.823420] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.823578] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.823689] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.823825] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.848654] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.848809] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.849060] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.849319] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.849808] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.850392] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.850638] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.850961] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.853159] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.853316] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.856448] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.857063] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.857203] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.857336] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.857646] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.857818] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.857980] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.858136] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.858289] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.858443] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.858582] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.858713] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.859159] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.859301] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.859824] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.860363] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [113.860491] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.860734] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.860899] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.861052] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.861200] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.861344] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.861587] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.861854] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.862029] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.862208] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.862342] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.862508] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.887174] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.887251] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.887408] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.887550] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.887832] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.887998] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.888110] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.888301] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.889958] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.890069] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.893148] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.893742] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.893811] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.894167] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.894289] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [113.894305] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.894416] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.894738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.894852] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [113.894979] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.895133] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.895449] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.895620] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.895781] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.895934] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.896083] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.896228] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.896376] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.896516] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.896962] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.897228] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.897633] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.898543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.898609] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [113.898715] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.898877] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.899026] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.899172] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.899429] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.899695] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.899874] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.900056] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.900190] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.900440] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.925195] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.925302] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.925483] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.925663] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.926008] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.926211] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.926377] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.926616] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.928325] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.928462] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.931573] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.932184] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.932318] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.932460] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [113.932757] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.932921] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.933074] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.933222] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.933375] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.933517] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [113.933655] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.933785] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.934230] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.934378] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.934886] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.935620] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.935808] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.935973] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.936125] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.936272] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.936424] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.936667] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.936966] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.937141] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.937319] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.937460] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.937620] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [113.962416] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [113.962510] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [113.962669] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [113.962845] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [113.963190] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [113.963394] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [113.963552] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [113.963790] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [113.965698] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [113.965816] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [113.968905] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [113.969473] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [113.969546] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.969909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.970034] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [113.970050] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.970154] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.970481] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.970600] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [113.970614] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.970720] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.971049] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.971168] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [113.971181] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.971282] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.971613] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.971736] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [113.971752] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [113.971857] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.972172] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.972290] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [113.972302] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [113.972413] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.972730] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.972845] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [113.972857] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [113.972960] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.973286] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.973417] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [113.973430] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [113.973535] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [113.973851] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [113.973968] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [113.973982] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [113.974510] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [113.975061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [113.975413] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.975540] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [113.975666] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.975787] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [113.975982] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [113.976213] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [113.976364] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [113.976532] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [113.976640] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [113.976772] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [114.048656] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [114.049068] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [114.049508] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [114.049919] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [114.050535] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [114.051505] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [114.051833] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [114.052616] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [114.054994] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.055128] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [114.059248] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [114.060254] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [114.060404] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [114.060660] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.061009] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [114.061156] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [114.061175] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:249:HDMI-A-1]
<7> [114.061308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [114.061674] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:HDMI-A-1] Same epoch counter 6
<7> [114.061690] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:255:DP-2]
<7> [114.061867] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:DP-2] Same epoch counter 1
<7> [114.061881] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [114.062193] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<6> [114.062344] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [114.063199] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.063543] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.063729] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [114.063899] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [114.064059] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [114.064220] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [114.064443] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.064592] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.064729] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<6> [114.065349] [IGT] i915_pm_rpm: exiting, ret=0
<7> [114.066476] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.066787] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.066968] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [114.067130] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [114.067284] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [114.067447] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [114.067612] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.067759] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.067895] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<6> [114.068510] Console: switching to colour frame buffer device 128x48
<7> [114.068961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [114.069266] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [114.069485] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [114.069646] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [114.069798] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [114.069947] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [114.070105] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [114.070248] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [114.070393] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
Created at 2023-08-13 20:39:04