Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline i915_display_info21 igt_runner21 run21 runtimes21 results21.json boot21 dmesg21

DetailValue
Hostname 
shard-snb4
Igt-Version 
IGT-Version: 1.27.1-gb7a2382f1 (x86_64) (Linux: 6.5.0-rc5-linus-v6.5-rc5-g52a93d39b17d+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.016s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.016s)
Dmesg
<6> [136.769569] Console: switching to colour dummy device 80x25
<6> [136.769725] [IGT] kms_force_connector_basic: executing
<7> [136.773041] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [136.773754] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [136.774076] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [136.774550] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [136.774561] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.774587] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.774934] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.775118] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.775609] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.775770] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.776160] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.776330] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.776336] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.776495] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.777798] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.777804] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.778089] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.778107] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.778114] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.778119] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.778124] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.778129] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.778166] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.778183] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.778355] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.778516] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.778890] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.779077] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.779413] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.779571] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.779576] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.779735] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.780993] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.780998] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.781221] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.781238] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.781244] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.781248] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.781252] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.781257] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.781304] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.781321] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.781489] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.781654] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.782033] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.782194] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.782528] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.782686] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.782690] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.782849] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.784157] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.784163] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.784385] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.784402] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.784407] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.784412] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.784416] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.784420] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [136.784553] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [136.784712] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 2 or reprobing
<7> [136.784719] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.784977] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.785140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.785469] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.785643] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.785659] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.785822] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.787225] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.787240] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.787501] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.787519] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.787525] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.787530] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.787535] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.787540] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.787581] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.787780] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.788006] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.788357] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.788580] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.788592] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.788751] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.790134] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.790146] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.790363] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.790380] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.790385] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.790389] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.790393] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.790397] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.790588] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [136.790611] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.790662] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [136.790667] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [136.790790] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.790796] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [136.790804] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.790808] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [136.790815] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.790830] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [136.790834] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [136.790838] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [136.790842] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.790846] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.790850] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.791064] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:61:VGA-1] EDID override set
<7> [136.791093] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.791139] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD monitor IGT
<7> [136.791144] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:VGA-1] ELD size 24, SAD count 0
<7> [136.791148] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:61:VGA-1] EDID changed, epoch counter 2
<7> [136.791263] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [136.791268] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [136.791276] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.791290] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [136.791294] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [136.791298] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.791302] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.791306] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.791410] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [136.791437] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.791646] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.791841] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.792244] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.792418] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.792429] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.792585] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.793916] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.793928] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.794154] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [136.794161] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [136.794168] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [136.794173] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [136.794180] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.794196] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.794200] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.794204] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.794208] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.794212] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.794354] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 2 to 0 or reprobing
<7> [136.794361] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.794387] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.794558] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.794719] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.795136] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.795295] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.795636] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.795796] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.795801] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.795998] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.797297] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.797303] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.797530] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.797547] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.797553] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.797558] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.797563] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.797567] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.797606] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.797623] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.797793] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.797998] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.798378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.798542] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.798892] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.799064] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.799069] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.799228] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.800461] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.800467] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.800688] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.800704] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.800710] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.800714] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.800718] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.800723] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<6> [136.800924] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [136.801104] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [136.801500] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [136.801508] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.801527] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.801700] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.801861] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.802267] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.802422] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.802753] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.803001] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.803010] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.803179] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.804507] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.804513] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.804737] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.804753] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.804759] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.804764] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.804768] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.804773] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.804810] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.804827] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.805067] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.805261] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.805608] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.805761] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.806147] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.806301] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.806306] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.806473] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.807691] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.807697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.807980] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.807997] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.808003] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.808007] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.808012] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.808016] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.808123] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:61:VGA-1] EDID override reset
<7> [136.808145] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.808163] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.808335] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.808496] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.808892] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.809072] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.809407] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.809570] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.809575] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.809734] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.811041] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.811047] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.811263] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.811279] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.811284] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.811288] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.811292] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.811296] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.811452] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [136.811459] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [136.811476] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [136.811830] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.812140] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [136.812484] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.812641] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.812647] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.812799] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [136.814180] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.814187] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [136.814349] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [136.814397] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [136.814413] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [136.814761] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.814933] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [136.815322] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.815508] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.815512] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.815664] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [136.816933] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.816939] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [136.817096] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [136.817216] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:64:HDMI-A-1] EDID override reset
<7> [136.817239] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [136.817255] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [136.817602] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.817756] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [136.818174] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.818331] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.818335] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.818487] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [136.819716] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.819721] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [136.819903] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [136.820083] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:72:DP-1] EDID override reset
<7> [136.820106] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:72:DP-1]
<7> [136.820123] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:72:DP-1]
<7> [136.820291] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:72:DP-1] disconnected
<6> [136.820729] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [136.820916] [drm:status_store] [CONNECTOR:61:VGA-1] force updated from 0 to 0 or reprobing
<7> [136.820927] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1]
<7> [136.820957] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:61:VGA-1] force=1
<7> [136.821146] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0x83f40000, result 1
<7> [136.821303] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT detected via hotplug
<7> [136.821653] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.821809] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [136.822260] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [136.822416] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.822421] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.822579] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [136.823947] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [136.823953] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [136.824173] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:VGA-1] probed modes :
<7> [136.824190] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [136.824195] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [136.824200] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [136.824205] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [136.824209] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [136.824263] [drm:status_store] [CONNECTOR:64:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [136.824269] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1]
<7> [136.824286] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:64:HDMI-A-1]
<7> [136.824636] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.824790] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [136.825199] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [136.825361] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.825366] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [136.825524] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [136.826830] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [136.826837] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [136.827054] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:64:HDMI-A-1] disconnected
<7> [136.827321] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<6> [136.847604] Console: switching to colour frame buffer device 128x48
Created at 2023-08-07 00:01:01