Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gb7a2382f1 (x86_64) (Linux: 6.5.0-rc5-linus-v6.5-rc5-g52a93d39b17d+ x86_64)
Out 
Opened device: /dev/dri/card0
Runtime PM support: 1
PC8 residency support: 0
DMC: fw loaded: yes
i915_runtime_pm_status:
Runtime power status: enabled
GPU idle: yes
IRQs disabled: no
Usage count: 0
PCI device power state: D0 [0]
Wakeref last acquired:
   track_intel_runtime_pm_wakeref+0x18/0xc0 [i915]
   intel_atomic_commit+0x25/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
   drm_ioctl_kernel+0xb4/0x150
   drm_ioctl+0x21d/0x420
   __x64_sys_ioctl+0x79/0xb0
Wakeref last released:
   __untrack_all_wakerefs+0x6f/0x80 [i915]
   __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915]
   __intel_runtime_pm_put+0x159/0x2b0 [i915]
   intel_atomic_commit_tail+0xa3f/0xd20 [i915]
   intel_atomic_commit+0x381/0x400 [i915]
   drm_atomic_commit+0x92/0xc0
   drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper]
   drm_mode_setcrtc+0x1e9/0x740
Wakeref count: 0
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.923s)
Err 
Starting subtest: basic-pci-d3-state
Subtest basic-pci-d3-state: SUCCESS (0.923s)
Dmesg
<6> [107.514291] Console: switching to colour dummy device 80x25
<6> [107.514397] [IGT] i915_pm_rpm: executing
<7> [107.517087] i915 0000:03:00.0: [drm:i915_gem_open [i915]]
<7> [107.517763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [107.517782] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [107.517912] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.518184] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.518319] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [107.518394] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:DP-2]
<7> [107.518405] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [107.518529] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.518785] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.518918] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:DP-2] disconnected
<7> [107.519011] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [107.519037] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [107.519159] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.519424] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.519558] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [107.519621] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [107.519633] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [107.519755] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.520056] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [107.520305] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [107.520652] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [107.520801] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [107.563923] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [107.563949] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [107.564100] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [107.564290] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [107.564440] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [107.564572] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [107.564914] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.565060] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [107.565133] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2]
<7> [107.565145] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [107.565269] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.565833] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [107.565958] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [107.566363] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [107.566478] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [107.566483] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [107.566599] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [107.571423] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [107.571427] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [107.571546] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.571684] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] disconnected
<7> [107.571756] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:276:DP-4]
<7> [107.571768] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [107.571895] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.572166] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.572304] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:276:DP-4] disconnected
<7> [107.572368] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3]
<7> [107.572380] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [107.572502] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.572772] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.572909] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] disconnected
<7> [107.579353] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [107.579369] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [107.579502] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.579760] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.579896] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [107.580355] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:DP-2]
<7> [107.580368] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [107.580490] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.580747] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.580881] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:DP-2] disconnected
<7> [107.581344] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [107.581357] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [107.581479] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.581745] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.581880] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [107.582347] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [107.582360] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [107.582482] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.582742] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [107.583026] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [107.583364] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [107.583513] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [107.626923] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [107.626949] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [107.627101] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [107.627292] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [107.627443] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [107.627574] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [107.627915] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.628063] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [107.628495] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2]
<7> [107.628508] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [107.628632] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.629175] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [107.629294] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [107.629580] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [107.629696] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [107.629699] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [107.629812] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [107.634645] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [107.634648] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [107.634766] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.634901] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] disconnected
<7> [107.635375] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:276:DP-4]
<7> [107.635388] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [107.635510] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.635766] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.635900] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:276:DP-4] disconnected
<7> [107.636358] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3]
<7> [107.636370] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [107.636492] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.636758] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.636891] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] disconnected
<7> [107.637465] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1]
<7> [107.637478] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [107.637601] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.637858] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.638000] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:DP-1] disconnected
<7> [107.638024] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:DP-2]
<7> [107.638035] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [107.638157] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.638414] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.638546] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:249:DP-2] disconnected
<7> [107.638569] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [107.638580] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [107.638698] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.639000] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.639148] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [107.639171] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3]
<7> [107.639182] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [107.639304] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.639560] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [107.639837] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [107.640182] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [107.640330] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [107.683621] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [107.683638] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [107.683796] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [107.683946] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [107.684132] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [107.684261] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [107.684601] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.684736] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-3] disconnected
<7> [107.684765] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2]
<7> [107.684777] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [107.684897] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.685468] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [107.685581] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [107.686009] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [107.686140] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [107.686143] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [107.686253] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [107.691117] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [107.691120] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [107.691237] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.691372] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] disconnected
<7> [107.691397] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:276:DP-4]
<7> [107.691408] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [107.691530] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.691787] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.691921] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:276:DP-4] disconnected
<7> [107.691955] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3]
<7> [107.691995] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [107.692128] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [107.692393] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [107.692527] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] disconnected
<7> [108.694840] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [108.696611] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [108.697527] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [108.698230] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [108.698621] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [108.698856] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [108.699053] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [108.699396] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [108.801277] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [108.801755] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [108.802447] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [108.803169] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [108.803865] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [108.804573] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [108.805236] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [108.806034] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [108.834881] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [108.835088] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [108.839156] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [108.840168] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [108.840544] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [108.840983] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.841512] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.841734] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [108.841764] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [108.842243] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.842445] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [108.842565] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.842961] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:DP-2] Same epoch counter 1
<7> [108.843102] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.843301] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [108.843612] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [108.844015] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [108.844224] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [108.844414] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [108.844817] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.845381] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [108.846359] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [108.846390] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [108.846592] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [108.847483] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [108.848192] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [108.848521] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [108.848747] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [108.848945] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [108.849279] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [108.874397] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [108.874559] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [108.874761] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [108.875033] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [108.875285] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [108.875597] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [108.875789] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [108.876100] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [108.905957] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [108.906224] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [108.911116] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [108.911842] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [108.912050] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.912575] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.912888] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] Same epoch counter 5
<7> [108.912925] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [108.913207] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.913644] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [108.914154] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [108.914620] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [108.914958] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [108.960583] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [108.960628] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [108.960923] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [108.961675] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [108.961991] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [108.962261] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [108.962749] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.963061] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [108.963101] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [108.963355] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.964245] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [108.964494] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [108.965091] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [108.965333] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [108.965343] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [108.965583] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [108.971467] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [108.971475] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [108.971683] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.971944] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] Same epoch counter 1
<7> [108.971972] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [108.972189] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [108.972552] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [108.972793] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:276:DP-4] Same epoch counter 1
<7> [108.972829] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [108.973497] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [108.974427] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [108.975147] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [108.975481] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [108.975713] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [108.975907] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [108.976167] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.076776] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.077139] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.077443] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.077786] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.078158] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.078497] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.078781] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.079194] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.108143] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.108815] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.117077] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.118285] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.118836] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.119510] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.120274] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.121184] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.121829] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.122477] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.123352] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.124058] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.125097] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [109.125167] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.125148] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [109.126693] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.128043] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.128848] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.129539] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.130172] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.130869] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.155218] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.155392] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.155671] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.156027] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.156363] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.156671] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.156898] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.157250] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.186920] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.187108] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.189853] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.190188] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.190292] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.190591] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.191111] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.191265] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.191538] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.191895] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.192075] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.192229] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.192594] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.192803] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [109.192896] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.193056] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.193329] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.193685] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.193855] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.194020] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.194383] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.195163] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] Same epoch counter 1
<7> [109.195190] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.195339] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.195626] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.195789] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [109.195806] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [109.195960] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.196244] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.196404] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:DP-2] Same epoch counter 1
<7> [109.196421] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [109.196565] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.196860] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.197031] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] Same epoch counter 5
<7> [109.197047] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.197193] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.197479] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.197751] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.198110] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [109.198285] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [109.241608] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [109.241627] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [109.241777] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [109.241981] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.242133] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.242266] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.242618] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.242759] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [109.242775] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [109.242897] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.243474] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [109.243590] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [109.243875] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [109.243999] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [109.244003] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [109.244116] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [109.249009] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [109.249013] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [109.249133] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.249274] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] Same epoch counter 1
<7> [109.249289] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [109.249414] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.249675] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.249812] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:276:DP-4] Same epoch counter 1
<7> [109.249826] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [109.249960] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.250230] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.250368] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] Same epoch counter 1
<7> [109.250384] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.250974] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.251790] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.252429] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.252691] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.252856] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.252993] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.253177] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<6> [109.295398] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state
<7> [109.343963] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [109.356191] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.356441] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.356788] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.357229] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.357629] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.358023] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.358361] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.358814] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.389108] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.389669] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.393697] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.394648] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.395148] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.395663] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.396325] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.397129] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.397662] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.398202] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.398968] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.399531] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.400585] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [109.400575] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.402021] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.403213] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.403900] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.404487] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.405021] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.405617] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.430330] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.430495] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.430715] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.431004] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.431297] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.431547] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.431756] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.432089] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.461894] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.462090] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.464638] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.464979] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.465129] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.465289] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.465569] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.465940] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.466120] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.466282] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.466705] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.466882] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.467495] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.468008] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [109.468037] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [109.468340] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.469012] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.469311] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.469507] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.469670] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.469885] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.571209] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.571584] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.572192] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.572784] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.573413] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.574013] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.574535] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.575234] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.604186] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.604835] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.609784] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.610643] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.611102] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.611903] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.612627] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [109.612713] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [109.613348] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.614171] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.614839] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:DP-2] Same epoch counter 1
<7> [109.614908] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [109.615534] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.616395] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.617680] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] Same epoch counter 5
<7> [109.617756] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [109.618387] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.619220] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.620046] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.620894] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [109.621416] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [109.666593] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [109.666611] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [109.666763] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [109.666952] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.667115] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.667244] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.667586] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.667867] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.668451] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [109.668489] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.669300] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.669939] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.670241] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.670404] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.670535] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.670716] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.770020] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.770230] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.770522] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.770866] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.771236] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.771555] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.771838] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.772249] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.802217] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.802993] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.808002] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.808921] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.809508] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.810175] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [109.810915] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.811829] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [109.812504] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.813141] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.814011] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.814691] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.815504] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [109.815509] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [109.815831] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.817390] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.818850] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.819699] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.820393] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.821035] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.821732] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.846333] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.846479] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.846712] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.847027] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.847318] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.847582] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.847809] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.848163] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [109.877919] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [109.878107] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [109.880855] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [109.881187] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [109.881291] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [109.881877] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [109.882031] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [109.882436] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [109.882570] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [109.882576] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [109.882708] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [109.887825] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [109.887830] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [109.887981] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [109.888156] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [109.888727] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] Same epoch counter 1
<7> [109.888760] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [109.889596] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [109.890251] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [109.890540] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [109.890726] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [109.890881] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [109.891096] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [109.991708] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [109.992069] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [109.992525] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [109.993071] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [109.993580] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [109.994088] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [109.994630] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [109.995381] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [110.024924] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.025158] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.027959] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [110.028350] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [110.028550] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.028768] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [110.029120] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.029539] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [110.029776] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.030008] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.030441] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.030682] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [110.031304] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [110.031357] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [110.032216] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.032967] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [110.033328] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [110.033582] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [110.033800] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [110.034085] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [110.058993] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [110.059166] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [110.059395] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [110.059674] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [110.059977] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [110.060233] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [110.060451] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [110.060782] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [110.090986] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.091303] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.094757] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [110.095293] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [110.095516] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.096026] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.096403] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [110.097072] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:276:DP-4] Same epoch counter 1
<7> [110.097298] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [110.098338] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.099253] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [110.099739] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [110.100123] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [110.100454] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [110.100848] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [110.101271] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [110.176832] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [110.177645] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [110.178418] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [110.179214] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [110.180023] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [110.181081] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [110.181794] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [110.182676] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [110.211806] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.211989] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.215685] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [110.216271] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [110.216571] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.216883] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.217068] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] Same epoch counter 1
<7> [110.217082] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.217099] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:DP-1]
<7> [110.217521] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:DP-1] Same epoch counter 1
<7> [110.217539] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:249:DP-2]
<7> [110.217715] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:249:DP-2] Same epoch counter 1
<7> [110.217731] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [110.218009] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [110.218142] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS
<7> [110.218182] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] Same epoch counter 5
<7> [110.218200] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-3]
<7> [110.218351] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.218645] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [110.218928] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.219283] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [110.219467] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling AUX_C
<7> [110.262964] i915 0000:03:00.0: [drm:drm_dp_dpcd_access [drm_display_helper]] AUX C/DDI C/PHY C: Too many retries, giving up. First error: -5
<7> [110.262987] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling AUX_C
<7> [110.263173] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [110.263397] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [110.263581] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.263744] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.264135] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.264308] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:264:DP-3] Same epoch counter 1
<7> [110.264328] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:272:HDMI-A-2]
<7> [110.264481] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.265073] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [110.265220] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [110.265631] i915 0000:03:00.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [110.265773] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [110.265779] i915 0000:03:00.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [110.265918] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [110.271343] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [110.271348] i915 0000:03:00.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [110.271497] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.271667] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:272:HDMI-A-2] Same epoch counter 1
<7> [110.271686] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:276:DP-4]
<7> [110.271837] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.272148] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.272318] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:276:DP-4] Same epoch counter 1
<7> [110.272335] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:284:HDMI-A-3]
<7> [110.272484] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.272794] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [110.272972] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:284:HDMI-A-3] Same epoch counter 1
<7> [110.275909] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.276089] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [110.276371] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.276751] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [110.276945] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.277110] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.277483] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [110.277893] [IGT] i915_pm_rpm: exiting, ret=0
<7> [110.279012] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.279164] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [110.279429] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.279806] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [110.279981] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.280127] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.280486] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [110.280772] Console: switching to colour frame buffer device 128x48
<7> [110.281207] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [110.281355] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [110.281619] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00
<7> [110.282006] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [110.282171] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5
<7> [110.282316] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01
<7> [110.282674] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on
Created at 2023-08-07 00:00:44