Results for igt@gem_exec_suspend@basic-s3@smem

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g354c536a4 (x86_64) (Linux: 6.5.0-rc3-linus-v6.5-rc3-g6eaae1980760+ x86_64)
Out	Opened device: /dev/dri/card0 Starting subtest: basic-S3 Starting dynamic subtest: smem [cmd] rtcwake: wakeup from "mem" using /dev/rtc0 at Sun Jul 23 22:42:25 2023 Dynamic subtest smem: SUCCESS (1.803s) Subtest basic-S3: SUCCESS (1.804s)
Err	Starting subtest: basic-S3 Starting dynamic subtest: smem Dynamic subtest smem: SUCCESS (1.803s) Subtest basic-S3: SUCCESS (1.804s)
Dmesg	<6> [402.937239] [IGT] gem_exec_suspend: executing <7> [402.946683] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [402.947242] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [402.947411] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [402.947647] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [402.948473] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [402.948601] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [402.949040] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <6> [402.956112] [IGT] gem_exec_suspend: starting subtest basic-S3 <6> [402.956476] [IGT] gem_exec_suspend: starting dynamic subtest smem <7> [402.958615] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [403.325302] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [403.337303] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <6> [403.737401] PM: suspend entry (s2idle) <6> [403.739088] Filesystems sync: 0.001 seconds <6> [403.739862] Freezing user space processes <6> [403.743955] Freezing user space processes completed (elapsed 0.004 seconds) <6> [403.743962] OOM killer disabled. <6> [403.743964] Freezing remaining freezable tasks <6> [403.745210] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) <6> [403.749023] serial 00:06: disabled <7> [403.749619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [403.749830] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [403.750007] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [403.750168] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [403.750328] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <5> [403.753111] sd 0:0:0:0: [sda] Synchronizing SCSI cache <5> [403.753938] sd 0:0:0:0: [sda] Stopping disk <7> [403.931666] PM: suspend of devices complete after 185.262 msecs <7> [403.931684] PM: start suspend of devices complete after 186.467 msecs <7> [403.936613] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [403.937173] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [403.937648] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [403.938136] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [403.938602] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [403.939087] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [403.939559] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [403.940046] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [403.940967] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [403.954085] PM: late suspend of devices complete after 22.390 msecs <7> [403.985121] PM: noirq suspend of devices complete after 28.644 msecs <6> [403.986879] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off <6> [403.988717] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry <7> [403.988730] PM: suspend-to-idle <7> [419.054499] Timekeeping suspended for 15.065 seconds <7> [419.054578] PM: Triggering wakeup from IRQ 9 <7> [419.055133] ACPI: PM: ACPI fixed event wakeup <7> [419.055141] PM: resume from suspend-to-idle <6> [419.057093] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit <6> [419.058793] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on <6> [419.072524] pcieport 0000:00:1d.2: Intel SPT PCH root port ACS workaround enabled <6> [419.072567] pcieport 0000:00:1d.0: Intel SPT PCH root port ACS workaround enabled <6> [419.072592] pcieport 0000:00:1d.3: Intel SPT PCH root port ACS workaround enabled <7> [419.085020] PM: noirq resume of devices complete after 26.212 msecs <7> [419.088100] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [419.088318] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [419.088832] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [419.089383] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [419.089600] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [419.089798] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [419.089994] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [419.090190] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [419.090452] PM: early resume of devices complete after 4.236 msecs <5> [419.092949] sd 0:0:0:0: [sda] Starting disk <6> [419.093694] power_meter ACPI000D:00: Found ACPI power meter. <7> [419.094872] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [419.096151] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [419.096419] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [419.096636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [419.096774] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [419.096899] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A <7> [419.097025] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [419.097149] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B <7> [419.097277] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B <7> [419.097401] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [419.097525] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C <7> [419.097701] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C <6> [419.097869] serial 00:06: activated <7> [419.097826] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [419.097951] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A <7> [419.098070] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:96:DP-MST A] hw state readout: disabled, pipe A <7> [419.098187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:97:DP-MST B] hw state readout: disabled, pipe B <7> [419.098305] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:98:DP-MST C] hw state readout: disabled, pipe C <7> [419.098428] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:106:DDI C/PHY C] hw state readout: disabled, pipe A <7> [419.098584] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DP-MST A] hw state readout: disabled, pipe A <7> [419.098719] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:109:DP-MST B] hw state readout: disabled, pipe B <7> [419.098836] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:110:DP-MST C] hw state readout: disabled, pipe C <7> [419.098963] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [419.099091] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [419.099218] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [419.099345] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [419.099478] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:DP-1] hw state readout: disabled <7> [419.099616] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:107:DP-2] hw state readout: disabled <7> [419.099759] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:113:HDMI-A-1] hw state readout: disabled <7> [419.099874] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [419.099989] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz <7> [419.100104] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [419.100218] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [419.100340] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz <7> [419.100455] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz <7> [419.100649] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [419.100829] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [419.101011] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz <7> [419.101164] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz <7> [419.101280] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [419.101396] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [419.101583] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [419.101744] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [419.101864] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [419.101984] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [419.102103] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [419.102217] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [419.102328] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [419.102521] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [fastset] <7> [419.102685] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [419.102824] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:39:plane 2A] fb: [NOFB], visible: no <7> [419.102950] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:47:cursor A] fb: [NOFB], visible: no <7> [419.103070] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [fastset] <7> [419.103190] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:52:plane 1B] fb: [NOFB], visible: no <7> [419.103310] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:60:plane 2B] fb: [NOFB], visible: no <7> [419.103430] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:68:cursor B] fb: [NOFB], visible: no <7> [419.103574] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [fastset] <7> [419.103708] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:73:plane 1C] fb: [NOFB], visible: no <7> [419.103829] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:81:plane 2C] fb: [NOFB], visible: no <7> [419.103949] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:89:cursor C] fb: [NOFB], visible: no <7> [419.104131] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:51:pipe A] <7> [419.104272] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:72:pipe B] <7> [419.104409] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:93:pipe C] <7> [419.104690] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [419.104836] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:95:DP-1] Same epoch counter 1 <7> [419.104852] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:107:DP-2] <7> [419.105060] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <7> [419.106010] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX C/DDI C/PHY C: DPCD: 12 0a 82 01 00 03 01 81 00 01 00 00 00 00 00 <7> [419.106886] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX C/DDI C/PHY C: DP branch: OUI 00-60-37 dev-ID 3355N2 HW-rev 1.0 SW-rev 1.3 quirks 0x0000 <7> [419.107458] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:107:DP-2] Same epoch counter 1 <7> [419.107475] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1] <7> [419.107960] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [419.108076] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [419.108459] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [419.108493] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [419.108726] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [419.108875] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [419.109062] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [419.109211] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [419.109378] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [419.109605] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [419.109763] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [419.110420] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [419.110426] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [419.110566] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [419.140623] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [419.140628] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [419.140740] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [419.140875] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] Same epoch counter 1 <6> [419.418472] ata4: SATA link down (SStatus 0 SControl 300) <6> [419.418519] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) <6> [419.418632] ata6: SATA link down (SStatus 0 SControl 300) <6> [419.420504] ata1.00: configured for UDMA/133 <7> [419.421068] PM: resume of devices complete after 330.607 msecs <6> [419.424922] OOM killer enabled. <6> [419.424930] Restarting tasks ... <6> [419.426440] ata7: SATA link down (SStatus 0 SControl 300) <6> [419.426462] ata2: SATA link down (SStatus 0 SControl 300) <6> [419.426479] ata8: SATA link down (SStatus 0 SControl 300) <6> [419.426496] ata3: SATA link down (SStatus 0 SControl 300) <6> [419.426512] ata5: SATA link down (SStatus 0 SControl 300) <4> [419.427261] done. <5> [419.427275] random: crng reseeded on system resumption <6> [419.428198] PM: suspend exit <7> [419.429303] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [419.450742] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [419.450916] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [419.451374] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [419.452831] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [419.816149] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <6> [419.825235] [IGT] gem_exec_suspend: finished subtest smem, SUCCESS <6> [419.825619] [IGT] gem_exec_suspend: finished subtest basic-S3, SUCCESS <7> [419.922704] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [419.922956] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [419.923174] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [419.923878] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [419.933075] [IGT] gem_exec_suspend: exiting, ret=0 <7> [419.933607] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-07-24 00:13:12