Results for igt@i915_module_load@load

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gfaa966f69 (x86_64) (Linux: 6.5.0-rc2-linus-v6.5-rc2-gfdf0eaf11452+ x86_64)
Out 
Starting subtest: load
Opened device: /dev/dri/card0
Subtest load: SUCCESS (4.828s)
Err 
Starting subtest: load
Subtest load: SUCCESS (4.828s)
Dmesg
<6> [97.230402] [IGT] i915_module_load: executing
<6> [97.747278] [IGT] i915_module_load: starting subtest load
<4> [100.573981]
<4> [100.573995] **********************************************************
<4> [100.573997] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [100.573999] ** **
<4> [100.574001] ** trace_printk() being used. Allocating extra memory. **
<4> [100.574003] ** **
<4> [100.574005] ** This means that this is a DEBUG kernel and it is **
<4> [100.574007] ** unsafe for production use. **
<4> [100.574009] ** **
<4> [100.574011] ** If you see this message and you are not debugging **
<4> [100.574012] ** the kernel, report this immediately to your vendor! **
<4> [100.574014] ** **
<4> [100.574016] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **
<4> [100.574018] **********************************************************
<7> [100.642816] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [100.643106] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found CougarPoint PCH
<7> [100.643419] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [100.643817] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 125000 kHz
<7> [100.644830] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 2048M
<7> [100.645040] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [100.645229] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M
<6> [100.646040] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [100.649892] Console: switching to colour dummy device 80x25
<7> [100.651493] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 00000000
<7> [100.651874] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 65536K
<7> [100.652912] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xdaef6018
<7> [100.653357] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0
<7> [100.653687] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [100.654008] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [100.654380] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [100.662278] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000483, SBCB callbacks 00000203
<7> [100.662729] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [100.663062] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [100.663468] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [100.664223] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [100.664840] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SANDYBRIDGE-M ", BDB version 161
<7> [100.665199] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [100.665763] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 269, min size 5)
<7> [100.666120] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [100.666491] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 22 (size 75, min size 22)
<7> [100.666842] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 23 (size 72, min size 72)
<7> [100.667187] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 200, min size 812)
<7> [100.667550] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 24, min size 34)
<7> [100.667895] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [100.668240] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1264, min size 1366)
<7> [100.668622] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 97, min size 305)
<7> [100.668962] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)
<7> [100.669319] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 1 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [100.669655] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [100.669991] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1022
<7> [100.670360] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [100.670703] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [100.671045] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6
<7> [100.671436] i915 0000:00:02.0: [drm:intel_bios_init [i915]] No SDVO device info is found in VBT
<7> [100.671771] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [100.672106] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 1
<7> [100.672465] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [100.672803] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 1
<7> [100.673137] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [100.673704] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 1
<7> [100.674052] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 00
<7> [100.674573] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [100.675934] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 0
<7> [100.676582] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 7 (0.7 usec)
<7> [100.676918] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 3 (1.5 usec)
<7> [100.677249] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 4 (2.0 usec)
<7> [100.677602] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency 22 (11.0 usec)
<7> [100.677940] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 7 (0.7 usec)
<7> [100.678268] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 3 (1.5 usec)
<7> [100.678643] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 4 (2.0 usec)
<7> [100.678972] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency 22 (11.0 usec)
<7> [100.679314] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 7 (0.7 usec)
<7> [100.679636] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 3 (1.5 usec)
<7> [100.680008] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 4 (2.0 usec)
<7> [100.680358] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency 22 (11.0 usec)
<7> [100.680687] i915 0000:00:02.0: [drm:i9xx_wm_init [i915]] WM latency values increased to avoid potential underruns
<7> [100.681014] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 12 (1.2 usec)
<7> [100.681376] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 3 (1.5 usec)
<7> [100.681706] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 4 (2.0 usec)
<7> [100.682034] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency 22 (11.0 usec)
<7> [100.682382] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 12 (1.2 usec)
<7> [100.682710] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 3 (1.5 usec)
<7> [100.683036] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 4 (2.0 usec)
<7> [100.683594] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency 22 (11.0 usec)
<7> [100.683927] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 12 (1.2 usec)
<7> [100.684253] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 3 (1.5 usec)
<7> [100.684602] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 4 (2.0 usec)
<7> [100.684931] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency 22 (11.0 usec)
<7> [100.685245] i915 0000:00:02.0: [drm:i9xx_wm_init [i915]] LP3 watermarks disabled due to potential for lost interrupts
<7> [100.685616] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM0 latency 12 (1.2 usec)
<7> [100.685943] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM1 latency 3 (1.5 usec)
<7> [100.686267] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM2 latency 4 (2.0 usec)
<7> [100.686607] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Primary WM3 latency not provided
<7> [100.686934] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM0 latency 12 (1.2 usec)
<7> [100.687260] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM1 latency 3 (1.5 usec)
<7> [100.687628] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM2 latency 4 (2.0 usec)
<7> [100.687954] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Sprite WM3 latency not provided
<7> [100.688277] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM0 latency 12 (1.2 usec)
<7> [100.688620] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM1 latency 3 (1.5 usec)
<7> [100.688947] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM2 latency 4 (2.0 usec)
<7> [100.689272] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Cursor WM3 latency not provided
<7> [100.693457] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 2 display pipes available.
<7> [100.694967] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] FDI PLL freq=270000
<7> [100.695408] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 400000 kHz, VCO 0 kHz, ref 0 kHz, bypass 0 kHz, voltage level 0
<7> [100.695756] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 400000 kHz
<7> [100.696098] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 360000 kHz
<6> [100.696762] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
<7> [100.697552] i915 0000:00:02.0: [drm:intel_lvds_init [i915]] LVDS PPS:t1+t2 300 t3 300 t4 5000 t5 3000 tx 2000 divider 6249 port 0 powerdown_on_reset 1
<7> [100.718111] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [100.718149] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [100.718273] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 3
<7> [100.718711] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] EDID PNPID mfg: LGD (0xe430), prod: 728, serial: 0, week: 0, year: 2010
<7> [100.719059] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (fallback): 0
<7> [100.719517] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 3
<7> [100.719867] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is static
<7> [100.720215] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x8 0xa
<7> [100.720859] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 200300
<7> [100.721212] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 5, serial: 4, week: 0, year: 2002
<7> [100.721828] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [100.722187] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 210 Hz, active high, min brightness 0, level 0, controller 0
<7> [100.722729] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found SDVO panel mode in BIOS VBT tables: "1600x1200": 60 162000 1600 1664 1856 2160 1200 1201 1204 1250 0x8 0xa
<7> [100.723437] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS State Enabled:1
<7> [100.723804] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] No PSR BDB found.
<7> [100.724138] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:61:LVDS-1] using preferred EDID fixed mode: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [100.724714] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:61:LVDS-1] DRRS type: none
<7> [100.725163] i915 0000:00:02.0: [drm:pch_setup_backlight [i915]] [CONNECTOR:61:LVDS-1] Using native PCH PWM for backlight control
<7> [100.725774] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:61:LVDS-1] backlight initialized, enabled, brightness 4648/4648
<7> [100.726110] i915 0000:00:02.0: [drm:intel_lvds_init [i915]] detected single-link lvds configuration
<7> [100.726724] i915 0000:00:02.0: [drm:intel_crt_reset [i915]] crt adpa set to 0xf40000
<7> [100.727076] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.743400] [drm:intel_sdvo_read_byte [i915]] i2c transfer returned -6
<7> [100.743771] i915 0000:00:02.0: [drm:intel_sdvo_init [i915]] No SDVO device found on SDVOB
<7> [100.744640] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.745040] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:67:HDMI B] using AUX B (VBT)
<7> [100.745265] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:67:HDMI B]
<7> [100.745524] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:67:HDMI B] Using DDC pin 0x5 (VBT)
<7> [100.746042] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:75:DP B] using AUX B (VBT)
<7> [100.746266] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:75:DP B]
<7> [100.746793] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:80:HDMI C] using AUX C (VBT)
<7> [100.747020] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:80:HDMI C]
<7> [100.747236] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:80:HDMI C] Using DDC pin 0x4 (VBT)
<7> [100.747681] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:84:HDMI D] using AUX D (VBT)
<7> [100.747902] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:84:HDMI D]
<7> [100.748119] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:84:HDMI D] Using DDC pin 0x6 (VBT)
<7> [100.748603] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:88:DP C] using AUX C (VBT)
<7> [100.748827] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:88:DP C]
<7> [100.749184] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:92:DP D] using AUX D (VBT)
<7> [100.749469] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:92:DP D]
<7> [100.749843] i915 0000:00:02.0: [drm:intel_init_pch_refclk [i915]] has_panel 1 has_lvds 1 has_ck505 0 using_ssc_source 0
<7> [100.750711] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:45:pipe A] hw state readout: enabled
<7> [100.750956] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:60:pipe B] hw state readout: disabled
<7> [100.751187] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:primary A] hw state readout: disabled, pipe A
<7> [100.751507] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:sprite A] hw state readout: disabled, pipe A
<7> [100.751778] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:cursor A] hw state readout: disabled, pipe A
<7> [100.752006] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:46:primary B] hw state readout: disabled, pipe B
<7> [100.752231] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:50:sprite B] hw state readout: disabled, pipe B
<7> [100.752492] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:56:cursor B] hw state readout: disabled, pipe B
<7> [100.752781] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:62:LVDS] hw state readout: enabled, pipe A
<7> [100.753011] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:66:CRT] hw state readout: disabled, pipe A
<7> [100.753239] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:67:HDMI B] hw state readout: disabled, pipe A
<7> [100.753525] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [100.753810] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:75:DP B] hw state readout: disabled, pipe A
<7> [100.754046] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:80:HDMI C] hw state readout: disabled, pipe A
<7> [100.754283] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:84:HDMI D] hw state readout: disabled, pipe A
<7> [100.754553] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [100.754825] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:88:DP C] hw state readout: disabled, pipe A
<7> [100.755060] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [100.755280] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:92:DP D] hw state readout: disabled, pipe A
<7> [100.755586] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:45:pipe A] reserving PCH DPLL A
<7> [100.755851] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] PCH DPLL A hw state readout: pipe_mask 0x1, on 1
<7> [100.756095] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] PCH DPLL B hw state readout: pipe_mask 0x0, on 0
<7> [100.756511] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:61:LVDS-1] hw state readout: enabled
<7> [100.756788] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:65:VGA-1] hw state readout: disabled
<7> [100.757020] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:68:HDMI-A-1] hw state readout: disabled
<7> [100.757254] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [100.757491] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:76:DP-1] hw state readout: disabled
<7> [100.757800] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:81:HDMI-A-2] hw state readout: disabled
<7> [100.758028] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:85:HDMI-A-3] hw state readout: disabled
<7> [100.758261] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [100.758552] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:89:DP-2] hw state readout: disabled
<7> [100.758838] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [100.759057] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:93:DP-3] hw state readout: disabled
<7> [100.759472] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:primary A] min_cdclk 0 kHz
<7> [100.759709] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:35:sprite A] min_cdclk 0 kHz
<7> [100.759926] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:41:cursor A] min_cdclk 0 kHz
<7> [100.760143] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [100.760393] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:46:primary B] min_cdclk 0 kHz
<7> [100.760631] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:50:sprite B] min_cdclk 0 kHz
<7> [100.760853] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:56:cursor B] min_cdclk 0 kHz
<7> [100.761079] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [100.761546] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:45:pipe A] enable: yes [setup_hw_state]
<7> [100.761779] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: LVDS (0x10), output format: RGB, sink format: RGB
<7> [100.762007] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 18, dithering: 0
<7> [100.762236] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [100.762493] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [100.762744] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [100.762975] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [100.763207] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] fdi: lanes: 4; data_m: 1314215, data_n: 8388608, link_m: 146023, link_n: 524288, tu: 64
<7> [100.763486] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [100.763733] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [100.763960] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [100.764191] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1366x768": 60 75238 720 1414 1478 1582 400 772 779 792 0x40 0x9
<7> [100.764449] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1366x768": 60 75238 1366 1414 1478 1582 768 772 779 792 0x40 0x9
<7> [100.764696] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [100.764924] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1366x768": 60 75238 1366 1414 1478 1582 768 772 779 792 0x40 0x9
<7> [100.765157] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [100.765414] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 75238, pipe src: 720x400+0+0, pixel rate 75238
<7> [100.765713] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 0, ips linetime: 0
<7> [100.765944] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 1366x768+0+0, enabled, force thru: no
<7> [100.766176] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [100.766454] i915 0000:00:02.0: [drm:ibx_dump_hw_state [i915]] dpll_hw_state: dpll: 0x88040004, dpll_md: 0x0, fp0: 0x10c07, fp1: 0x30d07
<7> [100.766695] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [100.766926] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [100.767158] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [100.767416] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [100.767662] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [100.767886] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [100.768115] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:60:pipe B] enable: no [setup_hw_state]
<7> [100.768960] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [100.769160] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 80000000]
<7> [100.785439] i915 0000:00:02.0: [drm:i915_gem_init [i915]] Wrong MCH_SSKPD value: 0x16040307 This can cause underruns.
<7> [100.786601] i915 0000:00:02.0: [drm:intel_rps_init [i915]] Overclocking supported, max: 1300MHz, overclock: 1300MHz
<7> [100.786979] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0
<7> [100.787201] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on rcs'0
<7> [100.798657] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [PLANE:31:primary A] no fb, skipping
<7> [100.798928] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:60:pipe B] not active, skipping
<7> [100.799147] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [100.799430] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [100.800108] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [100.800303] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [100.800521] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [100.812478] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:61:LVDS-1] backlight device intel_backlight registered
<7> [100.812927] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:61:LVDS-1] generating connector hotplug event
<7> [100.813933] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:65:VGA-1] generating connector hotplug event
<7> [100.814866] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:68:HDMI-A-1] generating connector hotplug event
<7> [100.816112] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DP B bus for card0-DP-1
<7> [100.818066] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:76:DP-1] generating connector hotplug event
<7> [100.818858] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:81:HDMI-A-2] generating connector hotplug event
<7> [100.819319] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:85:HDMI-A-3] generating connector hotplug event
<7> [100.819892] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX C/DP C bus for card0-DP-2
<7> [100.820950] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:89:DP-2] generating connector hotplug event
<7> [100.821452] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX D/DP D bus for card0-DP-3
<7> [100.822615] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:93:DP-3] generating connector hotplug event
<6> [100.822687] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [100.824580] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 8 outputs detected
<6> [100.832358] ACPI: video: Video Device [VID] (multi-head: yes rom: no post: no)
<6> [100.834482] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input10
<7> [100.837824] [drm:drm_client_modeset_probe]
<7> [100.837889] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [100.838232] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [100.838305] i915 device info: pciid=0x0126 rev=0x09 platform=SANDYBRIDGE (subplatform=0x0) gen=6
<7> [100.838296] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] status updated from unknown to connected
<7> [100.838311] i915 device info: graphics version: 6
<7> [100.838315] i915 device info: media version: 6
<7> [100.838319] i915 device info: display version: 6
<7> [100.838325] i915 device info: graphics stepping: **
<7> [100.838328] i915 device info: media stepping: **
<7> [100.838330] i915 device info: display stepping: **
<7> [100.838333] i915 device info: base die stepping: **
<7> [100.838335] i915 device info: gt: 2
<7> [100.838339] i915 device info: memory-regions: 0x21
<7> [100.838343] i915 device info: page-sizes: 0x1000
<7> [100.838346] i915 device info: platform: SANDYBRIDGE
<7> [100.838349] i915 device info: ppgtt-size: 31
<7> [100.838352] i915 device info: ppgtt-type: 1
<7> [100.838355] i915 device info: dma_mask_size: 40
<7> [100.838358] i915 device info: is_mobile: yes
<7> [100.838362] i915 device info: is_lp: no
<7> [100.838365] i915 device info: require_force_probe: no
<7> [100.838369] i915 device info: is_dgfx: no
<7> [100.838436] i915 device info: has_64bit_reloc: no
<7> [100.838440] i915 device info: has_64k_pages: no
<7> [100.838444] i915 device info: gpu_reset_clobbers_display: no
<7> [100.838448] i915 device info: has_reset_engine: no
<7> [100.838452] i915 device info: has_3d_pipeline: yes
<7> [100.838455] i915 device info: has_4tile: no
<7> [100.838459] i915 device info: has_flat_ccs: no
<7> [100.838463] i915 device info: has_global_mocs: no
<7> [100.838467] i915 device info: has_gmd_id: no
<7> [100.838471] i915 device info: has_gt_uc: no
<7> [100.838474] i915 device info: has_heci_pxp: no
<7> [100.838478] i915 device info: has_heci_gscfi: no
<7> [100.838482] i915 device info: has_guc_deprivilege: no
<7> [100.838486] i915 device info: has_l3_ccs_read: no
<7> [100.838490] i915 device info: has_l3_dpf: no
<7> [100.838494] i915 device info: has_llc: yes
<7> [100.838497] i915 device info: has_logical_ring_contexts: no
<7> [100.838501] i915 device info: has_logical_ring_elsq: no
<7> [100.838505] i915 device info: has_media_ratio_mode: no
<7> [100.838509] i915 device info: has_mslice_steering: no
<7> [100.838513] i915 device info: has_oa_bpc_reporting: no
<7> [100.838516] i915 device info: has_oa_slice_contrib_limits: no
<7> [100.838520] i915 device info: has_oam: no
<7> [100.838524] i915 device info: has_one_eu_per_fuse_bit: no
<7> [100.838528] i915 device info: has_pxp: no
<7> [100.838532] i915 device info: has_rc6: yes
<7> [100.838535] i915 device info: has_rc6p: no
<7> [100.838539] i915 device info: has_rps: yes
<7> [100.838542] i915 device info: has_runtime_pm: no
<7> [100.838546] i915 device info: has_snoop: no
<7> [100.838549] i915 device info: has_coherent_ggtt: yes
<7> [100.838552] i915 device info: tuning_thread_rr_after_dep: no
<7> [100.838556] i915 device info: unfenced_needs_alignment: no
<7> [100.838560] i915 device info: hws_needs_physical: no
<7> [100.838564] i915 device info: has_pooled_eu: no
<7> [100.838568] i915 device info: cursor_needs_physical: no
<7> [100.838572] i915 device info: has_cdclk_crawl: no
<7> [100.838575] i915 device info: has_cdclk_squash: no
<7> [100.838579] i915 device info: has_ddi: no
<7> [100.838583] i915 device info: has_dp_mst: no
<7> [100.838587] i915 device info: has_dsb: no
<7> [100.838591] i915 device info: has_fpga_dbg: no
<7> [100.838594] i915 device info: has_gmch: no
<7> [100.838598] i915 device info: has_hotplug: yes
<7> [100.838602] i915 device info: has_hti: no
<7> [100.838606] i915 device info: has_ipc: no
<7> [100.838610] i915 device info: has_overlay: no
<7> [100.838613] i915 device info: has_psr: no
<7> [100.838617] i915 device info: has_psr_hw_tracking: no
<7> [100.838621] i915 device info: overlay_needs_physical: no
<7> [100.838624] i915 device info: supports_tv: no
<7> [100.838628] i915 device info: has_hdcp: no
<7> [100.838631] i915 device info: has_dmc: no
<7> [100.838635] i915 device info: has_dsc: no
<7> [100.838639] i915 device info: rawclk rate: 125000 kHz
<7> [100.838643] i915 device info: iommu: disabled
<7> [100.838648] i915 device info: available engines: 403
<7> [100.838653] i915 device info: slice total: 0, mask=0000
<7> [100.838657] i915 device info: subslice total: 0
<7> [100.838661] i915 device info: EU total: 0
<7> [100.838665] i915 device info: EU per subslice: 0
<7> [100.838669] i915 device info: has slice power gating: no
<7> [100.838673] i915 device info: has subslice power gating: no
<7> [100.838677] i915 device info: has EU power gating: no
<6> [100.838682] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [100.838686] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [100.838690] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [100.839148] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [100.839163] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [100.839399] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [100.839440] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [100.839455] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [100.839488] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [100.839997] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] trigger hotplug detect cycle: adpa=0xf40000
<7> [100.849433] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [100.849851] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [100.850779] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [100.851177] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [100.851824] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [100.852168] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [100.852181] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.852549] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [100.854726] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [100.854741] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [100.855115] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [100.856168] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] status updated from unknown to disconnected
<7> [100.856221] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [100.856267] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [100.856301] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [100.907478] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [100.923509] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.923526] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.923923] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [100.939503] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [100.939521] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [100.939934] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] status updated from unknown to disconnected
<7> [100.939989] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [100.940033] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [100.940066] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [100.940490] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] status updated from unknown to disconnected
<7> [100.940537] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [100.940578] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [100.940610] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [100.941209] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.941591] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [100.942138] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [100.942559] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.942571] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.942905] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [100.944959] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [100.944973] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [100.945342] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] status updated from unknown to disconnected
<7> [100.945396] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [100.945483] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [100.945517] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [100.946105] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [100.946466] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [100.947013] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [100.947351] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [100.947362] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [100.947777] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [100.949816] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [100.949831] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [100.950193] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] status updated from unknown to disconnected
<7> [100.950279] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [100.950312] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [100.950345] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [100.950739] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] status updated from unknown to disconnected
<7> [100.950787] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [100.950830] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [100.950862] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [100.951224] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] status updated from unknown to disconnected
<7> [100.951271] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<7> [100.951311] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [100.951321] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [100.951328] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [100.951335] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [100.951341] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [100.951348] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [100.951355] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [100.951361] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [100.951601] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [100.951642] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [100.951651] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [100.951658] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [100.951664] [drm:drm_client_modeset_probe] picking CRTCs for 8192x8192 config
<7> [100.951693] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<7> [100.951839] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<7> [100.951963] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<7> [100.956369] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 1366x768 fb: 0x00002000
<6> [100.958607] fbcon: i915drmfb (fb0) is primary device
<7> [100.960899] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:61:LVDS-1] Limiting display bpp to 24 (EDID bpp 0, max requested bpp 0, max platform bpp 36)
<7> [100.961328] i915 0000:00:02.0: [drm:intel_lvds_compute_config [i915]] forcing display bpp (was 24) to LVDS (18)
<7> [100.961750] i915 0000:00:02.0: [drm:ilk_fdi_compute_config [i915]] checking fdi config on pipe A, lanes 1
<7> [100.962087] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:45:pipe A] hw max bpp: 24, pipe bpp: 18, dithering: 1
<7> [100.962429] i915 0000:00:02.0: [drm:intel_pipe_config_compare [i915]] initial modeset and fastboot not set
<7> [100.962794] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:45:pipe A] fastset requirement not met in fdi_lanes (expected 4, found 1)
<7> [100.963130] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:45:pipe A] fastset requirement not met in fdi_m_n (expected tu 64 data 1314215/8388608 link 146023/524288, found tu 64, data 5259517/8388608 link 146097/524288)
<7> [100.963543] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:45:pipe A] fastset requirement not met in dpll_hw_state.fp1 (expected 0x00030d07, found 0x00010c07)
<7> [100.963891] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [100.964226] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:45:pipe A] releasing PCH DPLL A
<7> [100.964687] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:45:pipe A] allocated PCH DPLL A
<7> [100.965029] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:45:pipe A] reserving PCH DPLL A
<7> [100.965365] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:45:pipe A] enable: yes [modeset]
<7> [100.965731] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: LVDS (0x10), output format: RGB, sink format: RGB
<7> [100.966069] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 18, dithering: 1
<7> [100.966408] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [100.966808] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [100.967146] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [100.967611] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [100.967950] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] fdi: lanes: 1; data_m: 5259517, data_n: 8388608, link_m: 146097, link_n: 524288, tu: 64
<7> [100.968287] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [100.968705] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [100.969047] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [100.969382] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [100.969835] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [100.970173] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [100.970579] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "1366x768": 60 75238 1366 1414 1478 1582 768 772 779 792 0x40 0x9
<7> [100.970914] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=75238, hd=1366 hb=1366-1582 hs=1414-1478 ht=1582, vd=768 vb=768-792 vs=772-779 vt=792, flags=0x9
<7> [100.971253] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 75238, pipe src: 1366x768+0+0, pixel rate 75238
<7> [100.971726] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 0, ips linetime: 0
<7> [100.972062] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [100.972396] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [100.972855] i915 0000:00:02.0: [drm:ibx_dump_hw_state [i915]] dpll_hw_state: dpll: 0x88040004, dpll_md: 0x0, fp0: 0x10c07, fp1: 0x10c07
<7> [100.973194] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x3 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [100.973609] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [100.973954] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [100.974287] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [100.974700] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [100.975035] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [100.975372] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:primary A] fb: [FB:64] 1366x768 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [100.975832] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [100.976172] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 1366.000000x768.000000+0.000000+0.000000 dst: 1366x768+0+0
<7> [100.976598] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:35:sprite A] fb: [NOFB], visible: no
<7> [100.976924] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:41:cursor A] fb: [NOFB], visible: no
<7> [100.981808] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:61:LVDS-1] set backlight PWM = 0
<7> [100.983140] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [101.230858] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port B found
<7> [101.231291] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port C found
<7> [101.231685] i915 0000:00:02.0: [drm:g4x_dp_port_enabled [i915]] No pipe for DP port D found
<7> [101.249968] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable PCH DPLL A (active 0x1, on? 1) for [CRTC:45:pipe A]
<7> [101.250409] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling PCH DPLL A
<7> [101.250919] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:62:LVDS]
<7> [101.251153] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:66:CRT]
<7> [101.251373] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:67:HDMI B]
<7> [101.251642] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:75:DP B]
<7> [101.251879] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:80:HDMI C]
<7> [101.252101] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:84:HDMI D]
<7> [101.252318] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:88:DP C]
<7> [101.252534] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:92:DP D]
<7> [101.252780] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] PCH DPLL A
<7> [101.253092] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] PCH DPLL B
<7> [101.254033] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [101.255153] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI_RX_IIR 0x700
<7> [101.255381] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI train 1 done.
<7> [101.256308] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI_RX_IIR 0x600
<7> [101.256540] i915 0000:00:02.0: [drm:gen6_fdi_link_train [i915]] FDI train 2 done.
<7> [101.256821] i915 0000:00:02.0: [drm:ilk_pch_enable [i915]] FDI train done.
<7> [101.257058] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable PCH DPLL A (active 0x1, on? 0) for [CRTC:45:pipe A]
<7> [101.257280] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling PCH DPLL A
<7> [101.793364] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [101.794272] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:61:LVDS-1] set backlight PWM = 4648
<7> [101.842626] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:61:LVDS-1]
<7> [101.843395] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:45:pipe A]
<7> [101.844213] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] PCH DPLL A
<7> [101.845115] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=4648/4648
<6> [101.845307] Console: switching to colour frame buffer device 170x48
<7> [101.845419] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:61:LVDS-1] set backlight level = 4648
<6> [101.862397] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [101.873946] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [101.873986] [drm:drm_client_modeset_probe]
<7> [101.874295] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [101.874341] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [101.874355] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [101.874516] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [101.874543] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [101.874550] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [101.874568] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [101.875083] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [101.875352] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [101.875949] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [101.876308] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [101.876749] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [101.876982] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [101.876991] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.877241] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [101.878871] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [101.878878] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [101.879117] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [101.879322] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [101.879349] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [101.879368] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [101.930911] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [101.947000] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [101.947009] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.947207] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [101.963020] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [101.963028] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [101.963221] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [101.963246] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [101.963263] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [101.963461] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [101.963478] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [101.963494] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [101.964038] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.964263] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [101.964635] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [101.964820] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.964826] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.965095] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [101.966616] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [101.966622] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [101.966812] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [101.966835] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [101.966853] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [101.967346] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [101.967532] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [101.967899] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [101.968114] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [101.968120] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.968325] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [101.969844] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [101.969850] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [101.970097] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [101.970130] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [101.970151] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [101.970356] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [101.970374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [101.970391] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [101.970590] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<7> [101.970608] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [101.970612] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [101.970615] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [101.970617] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [101.970619] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [101.970621] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [101.970624] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [101.970626] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [101.970775] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [101.970806] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [101.970810] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [101.970812] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [101.970815] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [101.970856] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<7> [101.992315] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [101.992346] [drm:drm_client_modeset_probe]
<7> [101.992420] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1]
<7> [101.992445] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD monitor
<7> [101.992451] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:61:LVDS-1] ELD size 20, SAD count 0
<7> [101.992538] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:61:LVDS-1] probed modes :
<7> [101.992555] [drm:drm_mode_debug_printmodeline] Modeline "1366x768": 60 75200 1366 1414 1478 1582 768 772 779 792 0x48 0x9
<7> [101.992562] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1]
<7> [101.992579] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] [CONNECTOR:65:VGA-1] force=1
<7> [101.992814] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] ironlake hotplug adpa=0xf40000, result 0
<7> [101.993059] i915 0000:00:02.0: [drm:intel_crt_detect [i915]] CRT not detected via hotplug
<7> [101.993548] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [101.993734] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK on first message, retry
<7> [101.994070] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus vga] NAK for addr: 0050 w(1)
<7> [101.994258] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [101.994263] i915 0000:00:02.0: [drm:intel_crt_get_edid [i915]] CRT GMBUS EDID read failed, retry using GPIO bit-banging
<7> [101.994447] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus vga. force bit now 1
<7> [101.995998] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus vga
<7> [101.996004] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus vga. force bit now 0
<7> [101.996191] i915 0000:00:02.0: [drm:intel_crt_detect_ddc [i915]] CRT not detected via DDC:0x50 [no valid EDID found]
<7> [101.996377] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:65:VGA-1] disconnected
<7> [101.996401] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1]
<7> [101.996419] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:68:HDMI-A-1]
<7> [102.047010] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [102.063047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [102.063055] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.063246] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [102.079060] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [102.079067] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [102.079262] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:68:HDMI-A-1] disconnected
<7> [102.079286] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1]
<7> [102.079304] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:76:DP-1]
<7> [102.079498] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:76:DP-1] disconnected
<7> [102.079516] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2]
<7> [102.079532] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:81:HDMI-A-2]
<7> [102.079950] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.080201] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry
<7> [102.080598] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)
<7> [102.080783] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.080788] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.080968] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [102.082510] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [102.082516] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [102.082704] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:81:HDMI-A-2] disconnected
<7> [102.082726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3]
<7> [102.082743] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:85:HDMI-A-3]
<7> [102.083091] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [102.083276] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK on first message, retry
<7> [102.083684] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] NAK for addr: 0050 w(1)
<7> [102.083868] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [102.083872] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [102.084086] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [102.085686] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [102.085693] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [102.085885] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:85:HDMI-A-3] disconnected
<7> [102.085906] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2]
<7> [102.085924] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:89:DP-2]
<7> [102.086160] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:89:DP-2] disconnected
<7> [102.086184] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3]
<7> [102.086211] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:93:DP-3]
<7> [102.086466] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:93:DP-3] disconnected
<7> [102.086484] [drm:drm_client_modeset_probe] connector 61 enabled? yes
<7> [102.086488] [drm:drm_client_modeset_probe] connector 65 enabled? no
<7> [102.086490] [drm:drm_client_modeset_probe] connector 68 enabled? no
<7> [102.086493] [drm:drm_client_modeset_probe] connector 76 enabled? no
<7> [102.086495] [drm:drm_client_modeset_probe] connector 81 enabled? no
<7> [102.086497] [drm:drm_client_modeset_probe] connector 85 enabled? no
<7> [102.086499] [drm:drm_client_modeset_probe] connector 89 enabled? no
<7> [102.086502] [drm:drm_client_modeset_probe] connector 93 enabled? no
<7> [102.086531] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [102.086542] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 61
<7> [102.086545] [drm:drm_client_modeset_probe] looking for preferred mode on connector 61 0
<7> [102.086548] [drm:drm_client_modeset_probe] found mode 1366x768
<7> [102.086550] [drm:drm_client_modeset_probe] picking CRTCs for 1366x768 config
<7> [102.086573] [drm:drm_client_modeset_probe] desired mode 1366x768 set on crtc 45 (0,0)
<6> [102.495030] snd_hda_intel 0000:00:1b.0: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [102.496573] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [102.497889] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]
<7> [102.508503] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [102.574999] [IGT] i915_module_load: finished subtest load, SUCCESS
<6> [102.575069] [IGT] i915_module_load: exiting, ret=0
<6> [102.764504] i915_module_loa (1118) used greatest stack depth: 11464 bytes left
<6> [102.830316] snd_hda_codec_generic hdaudioC0D0: autoconfig for Generic: line_outs=1 (0x1f/0x0/0x0/0x0/0x0) type:speaker
<6> [102.830325] snd_hda_codec_generic hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [102.830329] snd_hda_codec_generic hdaudioC0D0: hp_outs=1 (0x19/0x0/0x0/0x0/0x0)
<6> [102.830332] snd_hda_codec_generic hdaudioC0D0: mono: mono_out=0x0
<6> [102.830335] snd_hda_codec_generic hdaudioC0D0: inputs:
<6> [102.830338] snd_hda_codec_generic hdaudioC0D0: Internal Mic=0x23
<6> [102.830341] snd_hda_codec_generic hdaudioC0D0: Mic=0x1b
<6> [102.839626] modprobe (1194) used greatest stack depth: 11296 bytes left
<7> [102.947313] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B
<7> [102.947708] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C
<7> [102.947944] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D
<6> [102.969358] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
<6> [102.976554] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
<6> [102.982575] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input13
<6> [102.988339] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input14
<6> [102.993060] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input15
Created at 2023-07-17 00:31:03