Results for igt@kms_force_connector_basic@force-edid

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gfaa966f69 (x86_64) (Linux: 6.5.0-rc2-linus-v6.5-rc2-gfdf0eaf11452+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.564s)
Err 
Starting subtest: force-edid
Subtest force-edid: SUCCESS (0.564s)
Dmesg
<6> [543.941695] Console: switching to colour dummy device 80x25
<6> [543.946224] [IGT] kms_force_connector_basic: executing
<7> [544.040029] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [544.046782] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [544.049808] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [544.057713] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [544.057793] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.058017] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.112546] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [544.126095] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.126173] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.128124] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [544.142773] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.142859] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [544.144822] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [544.145754] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.145961] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.198622] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [544.210595] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.210653] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.212182] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [544.224523] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.224601] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [544.226414] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [544.228966] [drm:status_store] [CONNECTOR:125:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [544.229054] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [544.229263] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [544.281662] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [544.293631] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [544.293710] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.295566] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [544.309069] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [544.309133] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [544.310629] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [544.311314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [544.311622] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [544.363618] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [544.375602] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [544.375677] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.377479] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [544.388805] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [544.388863] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [544.390516] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [544.393271] [drm:status_store] [CONNECTOR:135:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [544.393487] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [544.393698] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [544.446590] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [544.459015] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [544.459093] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.461103] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [544.473270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [544.473457] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [544.475183] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [544.475926] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [544.476064] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [544.529642] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [544.540818] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [544.540874] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.542203] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [544.553617] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [544.553677] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [544.555045] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [544.555647] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.555843] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.609658] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [544.620798] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.620855] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.622643] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [544.633876] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.633935] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [544.635570] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<6> [544.640871] [IGT] kms_force_connector_basic: starting subtest force-edid
<7> [544.643107] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [544.643199] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.643562] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.696529] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [544.713488] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.713640] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.715532] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [544.730020] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.730179] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [544.731694] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] status updated from disconnected to connected
<7> [544.735677] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [544.735899] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [544.735983] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [544.736054] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [544.736122] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [544.736189] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [544.738839] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.739040] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.793533] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [544.809279] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.809513] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [544.811527] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [544.827106] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [544.827246] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [544.831570] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [544.831769] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [544.831844] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [544.831939] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [544.832002] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [544.832062] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [544.867469] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:113:HDMI-A-1] EDID override set
<7> [544.867724] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.867878] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.870905] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:113:HDMI-A-1] ELD monitor IGT
<7> [544.870966] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:113:HDMI-A-1] ELD size 24, SAD count 0
<7> [544.923516] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [544.938165] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [544.939890] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [544.939983] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [544.940092] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [544.940160] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [544.940257] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [544.940504] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [544.940573] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [544.940634] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [544.940690] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [544.940748] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [544.942948] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:113:HDMI-A-1] EDID override reset
<7> [544.943850] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [544.944064] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [544.997518] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [545.010795] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.010944] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.012840] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [545.024995] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.025108] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [545.026514] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:113:HDMI-A-1] EDID changed, epoch counter 2
<7> [545.027844] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [545.027930] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [545.028018] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [545.028066] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [545.028134] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] probed modes :
<7> [545.028264] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [545.028308] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [545.028464] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [545.028525] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [545.028583] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [545.030768] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [545.030833] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [545.030986] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [545.084638] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [545.096684] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.096743] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.098713] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [545.111802] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.111887] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [545.114034] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] status updated from connected to disconnected
<7> [545.116118] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [545.119095] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [545.119315] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [545.173553] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [545.188144] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.188205] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.189859] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [545.202244] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.202303] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [545.204321] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<6> [545.209902] [IGT] kms_force_connector_basic: finished subtest force-edid, SUCCESS
<7> [545.211803] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [545.218811] [drm:status_store] [CONNECTOR:95:eDP-1] force updated from 0 to 0 or reprobing
<7> [545.218903] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [545.219123] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [545.222668] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [545.224622] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [545.227003] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [545.228912] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [545.230849] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [545.230934] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [545.231000] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [545.231251] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [545.232891] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [545.236788] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [545.238294] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [545.242085] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [545.242228] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [545.242882] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [545.243084] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [545.246217] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [545.247611] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [545.248891] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [545.250651] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [545.252877] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [545.252955] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [545.253014] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [545.253236] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [545.255006] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [545.258866] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [545.260739] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [545.265192] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [545.265476] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [545.267105] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:95:eDP-1] EDID override reset
<7> [545.267601] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [545.267811] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [545.272565] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [545.275574] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [545.277580] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [545.279518] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [545.282299] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [545.282514] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [545.282578] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [545.282802] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [545.284600] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [545.288266] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [545.290433] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [545.296534] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [545.296814] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [545.299493] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:103:DP-1] EDID override reset
<7> [545.299821] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [545.300031] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [545.302164] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [545.304849] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [545.304935] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [545.305151] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [545.361550] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [545.378504] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.378584] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.380540] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [545.395109] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.395177] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [545.396692] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [545.397585] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [545.397790] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [545.450518] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [545.464751] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.464828] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.466502] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [545.477758] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.477816] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [545.479596] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [545.481227] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:113:HDMI-A-1] EDID override reset
<7> [545.482082] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [545.482299] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [545.534619] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [545.545517] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.545573] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.546980] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [545.558328] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [545.558482] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [545.559874] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [545.561887] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:119:DP-2] EDID override reset
<7> [545.562122] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [545.562266] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [545.563880] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] disconnected
<7> [545.566420] [drm:status_store] [CONNECTOR:125:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [545.566509] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [545.566729] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [545.620625] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [545.632724] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [545.632803] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.634567] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [545.648283] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [545.648452] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [545.650218] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [545.651128] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [545.651689] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [545.704639] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [545.715466] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [545.715523] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.717022] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [545.729708] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [545.729782] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [545.731186] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [545.732850] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:125:HDMI-A-2] EDID override reset
<7> [545.733176] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [545.733731] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [545.787550] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [545.800893] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [545.800965] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.802826] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [545.814426] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [545.814503] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [545.816073] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [545.818179] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:129:DP-3] EDID override reset
<7> [545.818647] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3]
<7> [545.818864] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:129:DP-3]
<7> [545.820781] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3] disconnected
<7> [545.823211] [drm:status_store] [CONNECTOR:135:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [545.823282] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [545.823701] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [545.877656] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [545.890966] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [545.891032] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.892591] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [545.906457] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [545.906523] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [545.908094] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [545.908955] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [545.909159] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [545.962614] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [545.974907] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [545.974965] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [545.976714] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [545.989224] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [545.989291] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [545.990921] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [545.992610] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:135:HDMI-A-3] EDID override reset
<7> [545.992934] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [545.993142] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [546.046660] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [546.059004] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [546.059080] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.060891] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [546.073561] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [546.073641] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [546.076025] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<6> [546.089203] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [546.092320] [drm:status_store] [CONNECTOR:113:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [546.093112] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [546.093306] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [546.146620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [546.158767] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [546.158849] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.160723] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [546.173274] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [546.173459] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [546.175426] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [546.176408] [drm:status_store] [CONNECTOR:125:HDMI-A-2] force updated from 0 to 0 or reprobing
<7> [546.176492] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [546.176699] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [546.230593] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [546.243490] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [546.243572] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.245231] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [546.258858] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [546.258941] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [546.260716] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [546.261902] [drm:status_store] [CONNECTOR:135:HDMI-A-3] force updated from 0 to 0 or reprobing
<7> [546.261991] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [546.262207] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [546.316559] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [546.330074] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [546.330137] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.331796] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [546.345490] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [546.345577] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [546.347499] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [546.348962] [drm:status_store] [CONNECTOR:95:eDP-1] force updated from 0 to 0 or reprobing
<7> [546.349047] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [546.349263] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [546.352767] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [546.354055] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [546.355499] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [546.357146] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [546.359210] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [546.359295] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [546.359571] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [546.359829] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [546.361639] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [546.365744] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [546.367078] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [546.370858] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [546.371003] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [546.374025] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [546.405718] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [546.405914] [drm:drm_client_modeset_probe]
<7> [546.407039] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1]
<7> [546.407273] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:eDP-1]
<7> [546.410541] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:94:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [546.411826] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [546.413127] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [546.414872] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [546.416610] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [546.416696] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD monitor
<7> [546.416763] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:95:eDP-1] ELD size 20, SAD count 0
<7> [546.417031] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] VRR capable: no
<7> [546.418705] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [546.424036] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [546.425681] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:95:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? no, YCbCr 4:4:4->4:2:0 conversion? no
<7> [546.429902] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:eDP-1] probed modes :
<7> [546.430052] [drm:drm_mode_debug_printmodeline] Modeline "2400x1600": 60 252750 2400 2448 2480 2560 1600 1603 1613 1646 0x48 0xa
<7> [546.430139] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1]
<7> [546.430835] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:103:DP-1]
<7> [546.432643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:103:DP-1] disconnected
<7> [546.432785] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1]
<7> [546.432908] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:113:HDMI-A-1]
<7> [546.485620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] timed out, falling back to bit banging on pin 5
<7> [546.498278] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [546.498451] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.500706] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1
<7> [546.512761] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb
<7> [546.512823] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0
<7> [546.514643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:113:HDMI-A-1] disconnected
<7> [546.514863] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2]
<7> [546.515062] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:119:DP-2]
<7> [546.517006] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:119:DP-2] disconnected
<7> [546.517215] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2]
<7> [546.518064] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:125:HDMI-A-2]
<7> [546.570620] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4
<7> [546.582897] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [546.582979] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.584795] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1
<7> [546.597931] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc
<7> [546.598018] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0
<7> [546.599873] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:125:HDMI-A-2] disconnected
<7> [546.600089] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3]
<7> [546.600288] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:129:DP-3]
<7> [546.602192] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:129:DP-3] disconnected
<7> [546.602517] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3]
<7> [546.602711] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:135:HDMI-A-3]
<7> [546.656653] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpd] timed out, falling back to bit banging on pin 6
<7> [546.674160] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [546.674248] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [546.676141] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpd. force bit now 1
<7> [546.691014] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpd
<7> [546.691083] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpd. force bit now 0
<7> [546.692574] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:135:HDMI-A-3] disconnected
<7> [546.692785] [drm:drm_client_modeset_probe] connector 95 enabled? yes
<7> [546.692841] [drm:drm_client_modeset_probe] connector 103 enabled? no
<7> [546.692887] [drm:drm_client_modeset_probe] connector 113 enabled? no
<7> [546.692929] [drm:drm_client_modeset_probe] connector 119 enabled? no
<7> [546.692971] [drm:drm_client_modeset_probe] connector 125 enabled? no
<7> [546.693014] [drm:drm_client_modeset_probe] connector 129 enabled? no
<7> [546.693056] [drm:drm_client_modeset_probe] connector 135 enabled? no
<7> [546.694062] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [546.694220] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 95
<7> [546.694269] [drm:drm_client_modeset_probe] looking for preferred mode on connector 95 0
<7> [546.694315] [drm:drm_client_modeset_probe] found mode 2400x1600
<7> [546.694480] [drm:drm_client_modeset_probe] picking CRTCs for 2400x1600 config
<7> [546.694726] [drm:drm_client_modeset_probe] desired mode 2400x1600 set on crtc 51 (0,0)
<6> [546.739521] Console: switching to colour frame buffer device 300x100
Created at 2023-07-17 00:31:04