igt@i915_suspend@basic-s2idle-without-i915 on fi-kbl-guc@linus-v6.5-rc2 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gfaa966f69 (x86_64) (Linux: 6.5.0-rc2-linus-v6.5-rc2-gfdf0eaf11452+ x86_64)
Out	Starting subtest: basic-s2idle-without-i915 Opened device: /dev/dri/card0 [cmd] rtcwake: wakeup from "freeze" using /dev/rtc0 at Sun Jul 16 22:45:14 2023 Subtest basic-s2idle-without-i915: SUCCESS (2.241s)
Err	Starting subtest: basic-s2idle-without-i915 Subtest basic-s2idle-without-i915: SUCCESS (2.241s)
Dmesg	<6> [290.502143] [IGT] i915_suspend: executing <6> [290.507114] [IGT] i915_suspend: starting subtest basic-s2idle-without-i915 <5> [290.627303] Setting dangerous option enable_guc - tainting kernel <7> [290.671265] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K <7> [290.671482] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no) <6> [290.671627] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A <7> [290.671640] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH <7> [290.671780] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [290.672025] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [290.672142] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz <7> [290.672696] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [290.672805] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [290.672924] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M <6> [290.673025] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [290.673030] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [290.673772] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [290.673789] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047 <7> [290.673953] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K <7> [290.674264] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018 <7> [290.674421] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [290.674549] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [290.674675] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [290.674800] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [290.678853] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [290.679007] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [290.679136] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [290.679263] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [290.679391] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [290.679486] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [290.679578] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [290.679666] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no <7> [290.679756] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [290.679844] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [290.679952] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no <7> [290.680042] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [290.680130] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [290.680218] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [290.680736] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [290.680899] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206 <7> [290.681051] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [290.681192] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [290.681332] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [290.681471] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [290.681611] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812) <7> [290.681750] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34) <7> [290.681904] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [290.682058] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [290.682198] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [290.682337] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78) <7> [290.682471] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [290.682606] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [290.682740] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [290.682894] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [290.683047] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [290.683187] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [290.683321] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [290.683456] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4 <7> [290.683591] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [290.683726] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8 <7> [290.683872] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [290.684023] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0 <7> [290.684159] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [290.684306] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [290.684485] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [290.684638] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [290.684776] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [290.685335] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [290.685477] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [290.685627] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [290.685813] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.685961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [290.686108] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [290.686254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [290.686432] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [290.686569] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [290.686705] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [290.686841] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [290.687026] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin <6> [290.687916] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) <7> [290.688245] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [290.688644] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [290.688788] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [290.688944] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [290.689074] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [290.689203] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [290.689331] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [290.689457] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [290.689584] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [290.689710] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [290.689837] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [290.691114] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [290.692189] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [290.692382] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port A is not present <7> [290.692538] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (platform default) <7> [290.692678] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B] <7> [290.692802] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT) <7> [290.693184] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:104:DDI C/PHY C] using AUX C (platform default) <7> [290.693324] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C] <7> [290.693448] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [290.693643] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present <7> [290.693796] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] using AUX A (VBT) <7> [290.693948] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E] <7> [290.694223] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [290.694630] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [290.694793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [290.694970] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [290.695135] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [290.695274] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A <7> [290.695411] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [290.695549] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B <7> [290.695686] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B <7> [290.695823] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [290.695973] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C <7> [290.696145] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C <7> [290.696304] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [290.696443] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A <7> [290.696580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A <7> [290.696717] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A <7> [290.696865] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [290.697052] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [290.697193] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [290.697333] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [290.697504] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled <7> [290.697650] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled <7> [290.697793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled <7> [290.697934] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [290.698094] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz <7> [290.698225] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [290.698354] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [290.698492] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz <7> [290.698624] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz <7> [290.698754] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [290.698902] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [290.699068] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz <7> [290.699201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz <7> [290.699332] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [290.699461] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [290.699621] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [290.699758] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [290.699908] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [290.700078] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [290.700214] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [290.700346] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [290.700474] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [290.702936] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [240K, 784K) <7> [290.703069] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [290.703178] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000] <7> [290.703292] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [290.703423] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global <7> [290.704439] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0 <7> [290.704576] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0 <7> [290.704704] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0 <7> [290.707291] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3) <7> [290.707462] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs. <7> [290.707616] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset <7> [290.734258] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f <7> [290.734428] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0 <7> [290.734559] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000 <7> [290.734689] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3 <7> [290.734817] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a <7> [290.734960] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004 <7> [290.735092] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0 <7> [290.735222] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0 <7> [290.735351] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0 <7> [290.735480] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0 <7> [290.735609] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0 <7> [290.735760] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0 <7> [290.735908] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0 <7> [290.736040] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0 <7> [290.736170] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no <6> [290.737354] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1 <6> [290.737359] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0 <7> [290.744362] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0 <7> [290.745019] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <6> [290.745165] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled <6> [290.745168] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled <7> [290.752914] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <7> [290.753158] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping <7> [290.753288] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping <7> [290.753415] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping <7> [290.753541] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [290.753687] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [290.754185] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [290.754292] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [290.754390] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [290.754487] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [290.757084] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event <7> [290.757607] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event <7> [290.758126] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1 <7> [290.759177] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event <6> [290.759249] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [290.761901] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <6> [290.777742] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [290.778700] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input85 <7> [290.779386] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [290.780235] [drm:drm_client_modeset_probe] <7> [290.780153] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [290.780403] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [290.780641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [290.780604] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [290.780696] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [290.780802] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [290.781637] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [290.781783] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [290.781801] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [290.782007] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9 <7> [290.782012] i915 device info: graphics version: 9 <7> [290.782015] i915 device info: media version: 9 <7> [290.782018] i915 device info: display version: 9 <7> [290.782021] i915 device info: graphics stepping: F0 <7> [290.782024] i915 device info: media stepping: F0 <7> [290.782027] i915 device info: display stepping: C0 <7> [290.782029] i915 device info: base die stepping: <7> [290.782032] i915 device info: gt: 2 <7> [290.782035] i915 device info: memory-regions: 0x21 <7> [290.782038] i915 device info: page-sizes: 0x11000 <7> [290.782041] i915 device info: platform: KABYLAKE <7> [290.782044] i915 device info: ppgtt-size: 48 <7> [290.782047] i915 device info: ppgtt-type: 2 <7> [290.782050] i915 device info: dma_mask_size: 39 <7> [290.782053] i915 device info: is_mobile: no <7> [290.782056] i915 device info: is_lp: no <7> [290.782059] i915 device info: require_force_probe: no <7> [290.782061] i915 device info: is_dgfx: no <7> [290.782064] i915 device info: has_64bit_reloc: yes <7> [290.782067] i915 device info: has_64k_pages: no <7> [290.782070] i915 device info: gpu_reset_clobbers_display: no <7> [290.782073] i915 device info: has_reset_engine: yes <7> [290.782076] i915 device info: has_3d_pipeline: yes <7> [290.782079] i915 device info: has_4tile: no <7> [290.782082] i915 device info: has_flat_ccs: no <7> [290.782085] i915 device info: has_global_mocs: no <7> [290.782087] i915 device info: has_gmd_id: no <7> [290.782090] i915 device info: has_gt_uc: yes <7> [290.782093] i915 device info: has_heci_pxp: no <7> [290.782096] i915 device info: has_heci_gscfi: no <7> [290.782099] i915 device info: has_guc_deprivilege: no <7> [290.782102] i915 device info: has_l3_ccs_read: no <7> [290.782105] i915 device info: has_l3_dpf: no <7> [290.782108] i915 device info: has_llc: yes <7> [290.782111] i915 device info: has_logical_ring_contexts: yes <7> [290.782113] i915 device info: has_logical_ring_elsq: no <7> [290.782116] i915 device info: has_media_ratio_mode: no <7> [290.782119] i915 device info: has_mslice_steering: no <7> [290.782122] i915 device info: has_oa_bpc_reporting: no <7> [290.782125] i915 device info: has_oa_slice_contrib_limits: no <7> [290.782128] i915 device info: has_oam: no <7> [290.782131] i915 device info: has_one_eu_per_fuse_bit: no <7> [290.782134] i915 device info: has_pxp: no <7> [290.782137] i915 device info: has_rc6: yes <7> [290.782139] i915 device info: has_rc6p: no <7> [290.782142] i915 device info: has_rps: yes <7> [290.782145] i915 device info: has_runtime_pm: yes <7> [290.782148] i915 device info: has_snoop: no <7> [290.782151] i915 device info: has_coherent_ggtt: yes <7> [290.782154] i915 device info: tuning_thread_rr_after_dep: no <7> [290.782156] i915 device info: unfenced_needs_alignment: no <7> [290.782159] i915 device info: hws_needs_physical: no <7> [290.782162] i915 device info: has_pooled_eu: no <7> [290.782165] i915 device info: cursor_needs_physical: no <7> [290.782168] i915 device info: has_cdclk_crawl: no <7> [290.782171] i915 device info: has_cdclk_squash: no <7> [290.782173] i915 device info: has_ddi: yes <7> [290.782176] i915 device info: has_dp_mst: yes <7> [290.782179] i915 device info: has_dsb: no <7> [290.782182] i915 device info: has_fpga_dbg: yes <7> [290.782185] i915 device info: has_gmch: no <7> [290.782188] i915 device info: has_hotplug: yes <7> [290.782190] i915 device info: has_hti: no <7> [290.782193] i915 device info: has_ipc: yes <7> [290.782196] i915 device info: has_overlay: no <7> [290.782199] i915 device info: has_psr: yes <7> [290.782201] i915 device info: has_psr_hw_tracking: yes <7> [290.782204] i915 device info: overlay_needs_physical: no <7> [290.782207] i915 device info: supports_tv: no <7> [290.782210] i915 device info: has_hdcp: yes <7> [290.782213] i915 device info: has_dmc: yes <7> [290.782215] i915 device info: has_dsc: no <7> [290.782218] i915 device info: rawclk rate: 24000 kHz <7> [290.782221] i915 device info: iommu: enabled <7> [290.782224] i915 device info: available engines: 40403 <7> [290.782227] i915 device info: slice total: 1, mask=0001 <7> [290.782230] i915 device info: subslice total: 3 <7> [290.782233] i915 device info: slice0: 3 subslices, mask=00000007 <7> [290.782236] i915 device info: slice1: 0 subslices, mask=00000000 <7> [290.782239] i915 device info: slice2: 0 subslices, mask=00000000 <7> [290.782242] i915 device info: EU total: 24 <7> [290.782245] i915 device info: EU per subslice: 8 <7> [290.782248] i915 device info: has slice power gating: no <7> [290.782250] i915 device info: has subslice power gating: no <7> [290.782253] i915 device info: has EU power gating: yes <6> [290.782256] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [290.782259] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [290.782262] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [290.782328] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [290.782482] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [290.782490] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [290.782673] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [290.785903] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [290.785912] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [290.786156] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [290.786556] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [290.786766] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [290.786986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [290.787623] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.788164] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected <7> [290.788423] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [290.788796] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [290.788818] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [290.789051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.790184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [290.790376] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [290.790753] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [290.791276] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [290.791284] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [290.791468] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [290.806756] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [290.806764] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [290.806973] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.807187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected <7> [290.807218] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [290.807247] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [290.807266] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [290.807448] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.808048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.808265] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] status updated from unknown to disconnected <7> [290.808296] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [290.808320] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [290.808331] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [290.808335] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [290.808339] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [290.808445] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [290.808468] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [290.808502] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [290.808529] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [290.809603] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.809815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [290.810359] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [290.811014] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [290.811220] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [290.811419] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [290.812066] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.812497] [drm:drm_client_modeset_probe] <7> [290.812763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [290.812814] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [290.813080] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.814319] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [290.814520] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [290.815667] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [290.816142] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [290.816150] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [290.816303] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [290.832582] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [290.832593] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [290.832769] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.833008] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [290.833035] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [290.833053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [290.833183] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.833898] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [290.834184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [290.834314] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [290.834624] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [290.835052] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [290.835058] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [290.835207] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <6> [290.835304] [IGT] Unloading i915 <7> [290.849852] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [290.849868] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [290.849995] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.850127] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [290.850144] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [290.850156] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [290.850271] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.850876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [290.851012] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [290.851027] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [290.851035] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [290.851038] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [290.851041] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [290.851129] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [290.851142] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [290.851176] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [290.851237] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [290.851398] [drm:drm_client_modeset_probe] <7> [290.851452] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <6> [290.851389] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [290.851472] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [290.851626] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [290.851744] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [290.852271] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [290.852815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [290.853137] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10 <7> [290.853346] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [290.853499] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [290.853843] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [290.854033] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [290.854038] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [290.854148] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [290.857057] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [290.857063] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [290.857180] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [290.857196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [290.857207] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [290.857526] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [290.857629] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [290.857929] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [290.858100] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [290.858106] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [290.858255] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [290.861208] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [290.861213] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [290.861324] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [290.861339] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [290.861351] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [290.861484] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [290.861496] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [290.861499] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [290.861502] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [290.861505] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [290.861521] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [290.861531] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [290.861550] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [290.861563] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <6> [290.880574] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC887-VD: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line <6> [290.880591] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) <6> [290.880596] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0) <6> [290.880600] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 <6> [290.880604] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x0 <6> [290.880607] snd_hda_codec_realtek hdaudioC0D0: inputs: <6> [290.880611] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19 <6> [290.880615] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18 <6> [290.880618] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a <7> [290.911001] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B <7> [290.911150] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B <7> [290.911268] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B <7> [290.911384] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C <7> [290.911499] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C <7> [290.911613] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C <7> [290.911727] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D <7> [290.911842] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D <7> [290.911974] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D <6> [290.917109] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input86 <6> [290.919246] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input87 <6> [290.920059] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1f.3/sound/card0/input88 <6> [290.922829] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1f.3/sound/card0/input89 <6> [290.923701] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input90 <6> [290.924377] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input91 <6> [290.925146] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input92 <6> [290.925797] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input93 <7> [291.037163] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [291.037515] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [291.037694] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [291.037886] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [291.038493] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [291.113641] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [291.113779] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [291.114212] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [291.114749] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [291.114961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [291.115079] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [291.115197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [291.115313] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [291.136116] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915] <7> [291.173407] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper <6> [291.710835] PM: suspend entry (s2idle) <6> [291.713394] Filesystems sync: 0.002 seconds <6> [291.715567] Freezing user space processes <6> [291.720013] Freezing user space processes completed (elapsed 0.004 seconds) <6> [291.720046] OOM killer disabled. <6> [291.720049] Freezing remaining freezable tasks <6> [291.721112] Freezing remaining freezable tasks completed (elapsed 0.001 seconds) <6> [291.739961] serial 00:02: disabled <6> [291.740272] e1000e: EEE TX LPI TIMER: 00000011 <5> [291.741828] sd 2:0:0:0: [sda] Synchronizing SCSI cache <5> [291.741885] sd 2:0:0:0: [sda] Stopping disk <7> [291.804970] PM: suspend of devices complete after 71.745 msecs <7> [291.804989] PM: start suspend of devices complete after 83.794 msecs <7> [291.810721] PM: late suspend of devices complete after 5.721 msecs <7> [291.838496] PM: noirq suspend of devices complete after 23.834 msecs <6> [291.842953] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off <6> [291.847847] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry <7> [291.847923] PM: suspend-to-idle <7> [307.152927] Timekeeping suspended for 15.443 seconds <7> [307.153114] PM: Triggering wakeup from IRQ 9 <7> [307.153456] ACPI: PM: ACPI fixed event wakeup <7> [307.153474] PM: resume from suspend-to-idle <6> [307.158398] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit <6> [307.159325] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on <7> [307.172654] PM: noirq resume of devices complete after 13.322 msecs <7> [307.175775] PM: early resume of devices complete after 1.547 msecs <5> [307.178141] sd 2:0:0:0: [sda] Starting disk <6> [307.187552] serial 00:02: activated <6> [307.502634] ata6: SATA link down (SStatus 4 SControl 300) <6> [307.502689] ata4: SATA link down (SStatus 4 SControl 300) <6> [307.502745] ata2: SATA link down (SStatus 4 SControl 300) <6> [307.502802] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) <6> [307.502908] ata5: SATA link down (SStatus 4 SControl 300) <6> [307.502962] ata1: SATA link down (SStatus 4 SControl 300) <6> [307.707096] ata3.00: configured for UDMA/133 <7> [307.707624] PM: resume of devices complete after 531.842 msecs <6> [307.713463] OOM killer enabled. <6> [307.713466] Restarting tasks ... done. <5> [307.715979] random: crng reseeded on system resumption <6> [307.719911] PM: suspend exit <6> [307.724203] [IGT] Re-loading i915 <5> [307.849760] Setting dangerous option enable_guc - tainting kernel <7> [307.893742] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K <7> [307.893955] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no) <6> [307.894100] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A <7> [307.894111] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH <7> [307.894290] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [307.894582] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [307.894700] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz <7> [307.895266] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [307.895393] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [307.895494] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M <6> [307.895612] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [307.895616] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [307.896531] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [307.896551] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047 <7> [307.896707] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K <7> [307.897014] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018 <7> [307.897172] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [307.897299] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [307.897453] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [307.897591] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [307.901746] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [307.901885] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [307.902013] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [307.902140] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [307.902267] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [307.902386] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [307.902532] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [307.902675] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no <7> [307.902817] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [307.902959] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [307.903106] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no <7> [307.903249] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [307.903368] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [307.903490] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [307.904045] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [307.904245] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206 <7> [307.904465] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [307.904660] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [307.904802] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [307.904964] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [307.905156] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812) <7> [307.905399] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34) <7> [307.905602] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [307.905806] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [307.905995] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [307.906143] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78) <7> [307.906307] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [307.906514] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [307.906709] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [307.906907] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [307.907109] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [307.907272] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [307.907433] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [307.907620] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4 <7> [307.907814] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [307.908008] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8 <7> [307.908203] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [307.908410] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0 <7> [307.908567] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [307.908742] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [307.908995] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [307.909214] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [307.909428] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [307.910161] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [307.910371] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [307.910583] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [307.910840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [307.911029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [307.911166] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [307.911343] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [307.911600] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [307.911796] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [307.911990] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [307.912188] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [307.912407] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin <7> [307.913214] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <6> [307.913438] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) <7> [307.913777] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [307.913912] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [307.914044] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [307.914173] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [307.914300] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [307.914470] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [307.914598] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [307.914758] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [307.914980] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [307.915190] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <7> [307.916832] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available. <7> [307.918518] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [307.918801] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <6> [307.919011] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <7> [307.919179] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port A is not present <7> [307.919422] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (platform default) <7> [307.919620] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B] <7> [307.919799] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT) <7> [307.920211] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:104:DDI C/PHY C] using AUX C (platform default) <7> [307.920392] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C] <7> [307.920541] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [307.920736] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present <7> [307.920892] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] using AUX A (VBT) <7> [307.921031] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E] <7> [307.921313] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [307.921796] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [307.921960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [307.922117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [307.922298] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [307.922508] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A <7> [307.922676] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [307.922814] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B <7> [307.922955] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B <7> [307.923091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [307.923229] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C <7> [307.923433] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C <7> [307.923625] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [307.923765] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A <7> [307.923902] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A <7> [307.924038] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A <7> [307.924175] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [307.924319] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [307.924501] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [307.924679] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [307.924906] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled <7> [307.925053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled <7> [307.925197] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled <7> [307.925328] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [307.925477] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz <7> [307.925651] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [307.925829] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [307.925985] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz <7> [307.926117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz <7> [307.926248] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [307.926535] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [307.926715] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz <7> [307.926899] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz <7> [307.927039] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [307.927170] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [307.927332] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [307.927485] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [307.927622] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [307.927779] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [307.927945] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [307.928127] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [307.928276] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [307.930975] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [240K, 784K) <7> [307.931108] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [307.931216] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000] <7> [307.931330] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [307.931469] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global <7> [307.932598] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0 <7> [307.932734] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0 <7> [307.932863] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0 <7> [307.935447] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3) <7> [307.935620] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs. <7> [307.935773] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset <7> [307.962314] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f <7> [307.962488] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0 <7> [307.962619] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000 <7> [307.962749] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3 <7> [307.962878] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a <7> [307.963006] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004 <7> [307.963135] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0 <7> [307.963264] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0 <7> [307.963401] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0 <7> [307.963531] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0 <7> [307.963660] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0 <7> [307.963789] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0 <7> [307.963918] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0 <7> [307.964046] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0 <7> [307.964177] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no <6> [307.965409] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1 <6> [307.965413] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0 <7> [307.972323] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0 <7> [307.972997] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <6> [307.973143] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled <6> [307.973146] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled <7> [307.980150] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <7> [307.980407] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping <7> [307.980539] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping <7> [307.980666] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping <7> [307.980794] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [307.980940] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [307.981410] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [307.981515] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [307.981613] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [307.981710] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [307.985318] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event <7> [307.985719] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event <7> [307.986089] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1 <7> [307.987035] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event <6> [307.987109] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [307.989281] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <6> [308.007544] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [308.008900] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input94 <7> [308.009775] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [308.010642] [drm:drm_client_modeset_probe] <7> [308.010560] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [308.010795] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [308.010988] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [308.010998] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [308.011031] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [308.011199] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [308.011945] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [308.012144] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9 <7> [308.012150] i915 device info: graphics version: 9 <7> [308.012153] i915 device info: media version: 9 <7> [308.012156] i915 device info: display version: 9 <7> [308.012160] i915 device info: graphics stepping: F0 <7> [308.012163] i915 device info: media stepping: F0 <7> [308.012166] i915 device info: display stepping: C0 <7> [308.012169] i915 device info: base die stepping: <7> [308.012172] i915 device info: gt: 2 <7> [308.012176] i915 device info: memory-regions: 0x21 <7> [308.012179] i915 device info: page-sizes: 0x11000 <7> [308.012182] i915 device info: platform: KABYLAKE <7> [308.012185] i915 device info: ppgtt-size: 48 <7> [308.012189] i915 device info: ppgtt-type: 2 <7> [308.012192] i915 device info: dma_mask_size: 39 <7> [308.012195] i915 device info: is_mobile: no <7> [308.012198] i915 device info: is_lp: no <7> [308.012201] i915 device info: require_force_probe: no <7> [308.012205] i915 device info: is_dgfx: no <7> [308.012208] i915 device info: has_64bit_reloc: yes <7> [308.012211] i915 device info: has_64k_pages: no <7> [308.012214] i915 device info: gpu_reset_clobbers_display: no <7> [308.012217] i915 device info: has_reset_engine: yes <7> [308.012221] i915 device info: has_3d_pipeline: yes <7> [308.012224] i915 device info: has_4tile: no <7> [308.012227] i915 device info: has_flat_ccs: no <7> [308.012230] i915 device info: has_global_mocs: no <7> [308.012233] i915 device info: has_gmd_id: no <7> [308.012236] i915 device info: has_gt_uc: yes <7> [308.012240] i915 device info: has_heci_pxp: no <7> [308.012243] i915 device info: has_heci_gscfi: no <7> [308.012246] i915 device info: has_guc_deprivilege: no <7> [308.012249] i915 device info: has_l3_ccs_read: no <7> [308.012252] i915 device info: has_l3_dpf: no <7> [308.012255] i915 device info: has_llc: yes <7> [308.012258] i915 device info: has_logical_ring_contexts: yes <7> [308.012262] i915 device info: has_logical_ring_elsq: no <7> [308.012265] i915 device info: has_media_ratio_mode: no <7> [308.012268] i915 device info: has_mslice_steering: no <7> [308.012271] i915 device info: has_oa_bpc_reporting: no <7> [308.012274] i915 device info: has_oa_slice_contrib_limits: no <7> [308.012278] i915 device info: has_oam: no <7> [308.012281] i915 device info: has_one_eu_per_fuse_bit: no <7> [308.012284] i915 device info: has_pxp: no <7> [308.012287] i915 device info: has_rc6: yes <7> [308.012290] i915 device info: has_rc6p: no <7> [308.012293] i915 device info: has_rps: yes <7> [308.012297] i915 device info: has_runtime_pm: yes <7> [308.012300] i915 device info: has_snoop: no <7> [308.012303] i915 device info: has_coherent_ggtt: yes <7> [308.012306] i915 device info: tuning_thread_rr_after_dep: no <7> [308.012309] i915 device info: unfenced_needs_alignment: no <7> [308.012312] i915 device info: hws_needs_physical: no <7> [308.012315] i915 device info: has_pooled_eu: no <7> [308.012318] i915 device info: cursor_needs_physical: no <7> [308.012321] i915 device info: has_cdclk_crawl: no <7> [308.012324] i915 device info: has_cdclk_squash: no <7> [308.012327] i915 device info: has_ddi: yes <7> [308.012331] i915 device info: has_dp_mst: yes <7> [308.012334] i915 device info: has_dsb: no <7> [308.012337] i915 device info: has_fpga_dbg: yes <7> [308.012340] i915 device info: has_gmch: no <7> [308.012343] i915 device info: has_hotplug: yes <7> [308.012346] i915 device info: has_hti: no <7> [308.012390] i915 device info: has_ipc: yes <7> [308.012395] i915 device info: has_overlay: no <7> [308.012398] i915 device info: has_psr: yes <7> [308.012400] i915 device info: has_psr_hw_tracking: yes <7> [308.012403] i915 device info: overlay_needs_physical: no <7> [308.012406] i915 device info: supports_tv: no <7> [308.012408] i915 device info: has_hdcp: yes <7> [308.012411] i915 device info: has_dmc: yes <7> [308.012413] i915 device info: has_dsc: no <7> [308.012416] i915 device info: rawclk rate: 24000 kHz <7> [308.012419] i915 device info: iommu: enabled <7> [308.012422] i915 device info: available engines: 40403 <7> [308.012425] i915 device info: slice total: 1, mask=0001 <7> [308.012428] i915 device info: subslice total: 3 <7> [308.012430] i915 device info: slice0: 3 subslices, mask=00000007 <7> [308.012433] i915 device info: slice1: 0 subslices, mask=00000000 <7> [308.012436] i915 device info: slice2: 0 subslices, mask=00000000 <7> [308.012439] i915 device info: EU total: 24 <7> [308.012441] i915 device info: EU per subslice: 8 <7> [308.012444] i915 device info: has slice power gating: no <7> [308.012446] i915 device info: has subslice power gating: no <7> [308.012448] i915 device info: has EU power gating: yes <6> [308.012451] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [308.012454] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [308.012456] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [308.012378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [308.012576] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [308.012990] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [308.013168] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [308.013174] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [308.013300] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [308.016716] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [308.016725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [308.016964] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [308.017343] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [308.017568] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [308.017769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [308.018416] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [308.019055] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected <7> [308.019411] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [308.019437] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [308.019456] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [308.019673] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [308.021345] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [308.021522] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [308.021860] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [308.022287] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [308.022293] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [308.022439] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [308.037718] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [308.037726] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [308.037883] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [308.038036] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected <7> [308.038057] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [308.038075] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [308.038086] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [308.038227] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [308.038809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [308.038971] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] status updated from unknown to disconnected <7> [308.038990] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [308.039006] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [308.039015] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [308.039018] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [308.039021] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [308.039113] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [308.039132] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [308.039157] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [308.039176] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [308.040162] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [308.040322] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [308.040812] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [308.041452] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [308.041638] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [308.041829] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [308.042453] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [308.042774] [drm:drm_client_modeset_probe] <7> [308.042990] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [308.043055] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [308.043291] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [308.044626] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [308.044776] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [308.045424] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [308.045916] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [308.045922] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [308.046029] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <6> [308.051634] [IGT] i915_suspend: finished subtest basic-s2idle-without-i915, SUCCESS <7> [308.051702] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [308.052449] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [308.052672] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [308.053614] [IGT] i915_suspend: exiting, ret=0 <7> [308.053831] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

<6> [290.502143] [IGT] i915_suspend: executing

<6> [290.507114] [IGT] i915_suspend: starting subtest basic-s2idle-without-i915

<5> [290.627303] Setting dangerous option enable_guc - tainting kernel

<7> [290.671265] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K

<7> [290.671482] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no)

<6> [290.671627] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A

<7> [290.671640] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH

<7> [290.671780] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [290.672025] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [290.672142] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz

<7> [290.672696] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [290.672805] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [290.672924] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M

<6> [290.673025] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [290.673030] i915 0000:00:02.0: vgaarb: deactivate vga console

<6> [290.673772] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [290.673789] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047

<7> [290.673953] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K

<7> [290.674264] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018

<7> [290.674421] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0

<7> [290.674549] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [290.674675] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [290.674800] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [290.678853] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483

<7> [290.679007] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [290.679136] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [290.679263] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [290.679391] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [290.679486] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [290.679578] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [290.679666] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no

<7> [290.679756] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [290.679844] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [290.679952] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no

<7> [290.680042] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [290.680130] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [290.680218] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [290.680736] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [290.680899] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206

<7> [290.681051] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [290.681192] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)

<7> [290.681332] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [290.681471] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [290.681611] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)

<7> [290.681750] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)

<7> [290.681904] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [290.682058] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)

<7> [290.682198] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [290.682337] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)

<7> [290.682471] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [290.682606] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [290.682740] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [290.682894] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [290.683047] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [290.683187] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [290.683321] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [290.683456] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4

<7> [290.683591] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [290.683726] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8

<7> [290.683872] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [290.684023] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0

<7> [290.684159] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02

<7> [290.684306] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [290.684485] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [290.684638] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO

<7> [290.684776] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [290.685335] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz

<7> [290.685477] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz

<7> [290.685627] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [290.685813] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.685961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [290.686108] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [290.686254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [290.686432] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [290.686569] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [290.686705] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [290.686841] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [290.687026] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin

<6> [290.687916] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)

<7> [290.688245] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [290.688644] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV

<7> [290.688788] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us

<7> [290.688944] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [290.689074] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [290.689203] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [290.689331] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [290.689457] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [290.689584] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [290.689710] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [290.689837] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<7> [290.691114] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [290.692189] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0

<7> [290.692382] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port A is not present

<7> [290.692538] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (platform default)

<7> [290.692678] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B]

<7> [290.692802] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT)

<7> [290.693184] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:104:DDI C/PHY C] using AUX C (platform default)

<7> [290.693324] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C]

<7> [290.693448] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT)

<7> [290.693643] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present

<7> [290.693796] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] using AUX A (VBT)

<7> [290.693948] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E]

<7> [290.694223] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [290.694630] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled

<7> [290.694793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled

<7> [290.694970] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled

<7> [290.695135] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [290.695274] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A

<7> [290.695411] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A

<7> [290.695549] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B

<7> [290.695686] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B

<7> [290.695823] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B

<7> [290.695973] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C

<7> [290.696145] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C

<7> [290.696304] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C

<7> [290.696443] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [290.696580] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A

<7> [290.696717] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A

<7> [290.696865] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1

<7> [290.697052] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [290.697193] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [290.697333] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [290.697504] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled

<7> [290.697650] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled

<7> [290.697793] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled

<7> [290.697934] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [290.698094] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz

<7> [290.698225] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz

<7> [290.698354] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [290.698492] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz

<7> [290.698624] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz

<7> [290.698754] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz

<7> [290.698902] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [290.699068] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz

<7> [290.699201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz

<7> [290.699332] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz

<7> [290.699461] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [290.699621] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]

<7> [290.699758] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]

<7> [290.699908] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]

<7> [290.700078] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling

<7> [290.700214] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [290.700346] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [290.700474] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [290.702936] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [240K, 784K)

<7> [290.703069] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [290.703178] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]

<7> [290.703292] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0

<7> [290.703423] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global

<7> [290.704439] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0

<7> [290.704576] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0

<7> [290.704704] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0

<7> [290.707291] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)

<7> [290.707462] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs.

<7> [290.707616] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset

<7> [290.734258] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f

<7> [290.734428] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0

<7> [290.734559] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000

<7> [290.734689] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3

<7> [290.734817] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a

<7> [290.734960] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004

<7> [290.735092] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0

<7> [290.735222] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0

<7> [290.735351] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0

<7> [290.735480] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0

<7> [290.735609] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0

<7> [290.735760] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0

<7> [290.735908] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0

<7> [290.736040] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0

<7> [290.736170] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no

<6> [290.737354] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1

<6> [290.737359] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0

<7> [290.744362] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0

<7> [290.745019] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<6> [290.745165] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled

<6> [290.745168] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled

<7> [290.752914] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV

<7> [290.753158] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping

<7> [290.753288] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping

<7> [290.753415] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping

<7> [290.753541] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [290.753687] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [290.754185] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [290.754292] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [290.754390] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [290.754487] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [290.757084] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event

<7> [290.757607] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event

<7> [290.758126] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1

<7> [290.759177] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event

<6> [290.759249] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [290.761901] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected

<6> [290.777742] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [290.778700] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input85

<7> [290.779386] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)

<7> [290.780235] [drm:drm_client_modeset_probe]

<7> [290.780153] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D

<7> [290.780403] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C

<7> [290.780641] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [290.780604] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B

<7> [290.780696] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [290.780802] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E

<7> [290.781637] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [290.781783] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [290.781801] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [290.782007] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9

<7> [290.782012] i915 device info: graphics version: 9

<7> [290.782015] i915 device info: media version: 9

<7> [290.782018] i915 device info: display version: 9

<7> [290.782021] i915 device info: graphics stepping: F0

<7> [290.782024] i915 device info: media stepping: F0

<7> [290.782027] i915 device info: display stepping: C0

<7> [290.782029] i915 device info: base die stepping: **

<7> [290.782032] i915 device info: gt: 2

<7> [290.782035] i915 device info: memory-regions: 0x21

<7> [290.782038] i915 device info: page-sizes: 0x11000

<7> [290.782041] i915 device info: platform: KABYLAKE

<7> [290.782044] i915 device info: ppgtt-size: 48

<7> [290.782047] i915 device info: ppgtt-type: 2

<7> [290.782050] i915 device info: dma_mask_size: 39

<7> [290.782053] i915 device info: is_mobile: no

<7> [290.782056] i915 device info: is_lp: no

<7> [290.782059] i915 device info: require_force_probe: no

<7> [290.782061] i915 device info: is_dgfx: no

<7> [290.782064] i915 device info: has_64bit_reloc: yes

<7> [290.782067] i915 device info: has_64k_pages: no

<7> [290.782070] i915 device info: gpu_reset_clobbers_display: no

<7> [290.782073] i915 device info: has_reset_engine: yes

<7> [290.782076] i915 device info: has_3d_pipeline: yes

<7> [290.782079] i915 device info: has_4tile: no

<7> [290.782082] i915 device info: has_flat_ccs: no

<7> [290.782085] i915 device info: has_global_mocs: no

<7> [290.782087] i915 device info: has_gmd_id: no

<7> [290.782090] i915 device info: has_gt_uc: yes

<7> [290.782093] i915 device info: has_heci_pxp: no

<7> [290.782096] i915 device info: has_heci_gscfi: no

<7> [290.782099] i915 device info: has_guc_deprivilege: no

<7> [290.782102] i915 device info: has_l3_ccs_read: no

<7> [290.782105] i915 device info: has_l3_dpf: no

<7> [290.782108] i915 device info: has_llc: yes

<7> [290.782111] i915 device info: has_logical_ring_contexts: yes

<7> [290.782113] i915 device info: has_logical_ring_elsq: no

<7> [290.782116] i915 device info: has_media_ratio_mode: no

<7> [290.782119] i915 device info: has_mslice_steering: no

<7> [290.782122] i915 device info: has_oa_bpc_reporting: no

<7> [290.782125] i915 device info: has_oa_slice_contrib_limits: no

<7> [290.782128] i915 device info: has_oam: no

<7> [290.782131] i915 device info: has_one_eu_per_fuse_bit: no

<7> [290.782134] i915 device info: has_pxp: no

<7> [290.782137] i915 device info: has_rc6: yes

<7> [290.782139] i915 device info: has_rc6p: no

<7> [290.782142] i915 device info: has_rps: yes

<7> [290.782145] i915 device info: has_runtime_pm: yes

<7> [290.782148] i915 device info: has_snoop: no

<7> [290.782151] i915 device info: has_coherent_ggtt: yes

<7> [290.782154] i915 device info: tuning_thread_rr_after_dep: no

<7> [290.782156] i915 device info: unfenced_needs_alignment: no

<7> [290.782159] i915 device info: hws_needs_physical: no

<7> [290.782162] i915 device info: has_pooled_eu: no

<7> [290.782165] i915 device info: cursor_needs_physical: no

<7> [290.782168] i915 device info: has_cdclk_crawl: no

<7> [290.782171] i915 device info: has_cdclk_squash: no

<7> [290.782173] i915 device info: has_ddi: yes

<7> [290.782176] i915 device info: has_dp_mst: yes

<7> [290.782179] i915 device info: has_dsb: no

<7> [290.782182] i915 device info: has_fpga_dbg: yes

<7> [290.782185] i915 device info: has_gmch: no

<7> [290.782188] i915 device info: has_hotplug: yes

<7> [290.782190] i915 device info: has_hti: no

<7> [290.782193] i915 device info: has_ipc: yes

<7> [290.782196] i915 device info: has_overlay: no

<7> [290.782199] i915 device info: has_psr: yes

<7> [290.782201] i915 device info: has_psr_hw_tracking: yes

<7> [290.782204] i915 device info: overlay_needs_physical: no

<7> [290.782207] i915 device info: supports_tv: no

<7> [290.782210] i915 device info: has_hdcp: yes

<7> [290.782213] i915 device info: has_dmc: yes

<7> [290.782215] i915 device info: has_dsc: no

<7> [290.782218] i915 device info: rawclk rate: 24000 kHz

<7> [290.782221] i915 device info: iommu: enabled

<7> [290.782224] i915 device info: available engines: 40403

<7> [290.782227] i915 device info: slice total: 1, mask=0001

<7> [290.782230] i915 device info: subslice total: 3

<7> [290.782233] i915 device info: slice0: 3 subslices, mask=00000007

<7> [290.782236] i915 device info: slice1: 0 subslices, mask=00000000

<7> [290.782239] i915 device info: slice2: 0 subslices, mask=00000000

<7> [290.782242] i915 device info: EU total: 24

<7> [290.782245] i915 device info: EU per subslice: 8

<7> [290.782248] i915 device info: has slice power gating: no

<7> [290.782250] i915 device info: has subslice power gating: no

<7> [290.782253] i915 device info: has EU power gating: yes

<6> [290.782256] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled

<6> [290.782259] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [290.782262] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [290.782328] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [290.782482] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [290.782490] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [290.782673] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [290.785903] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [290.785912] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [290.786156] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [290.786556] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [290.786766] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [290.786986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [290.787623] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.788164] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected

<7> [290.788423] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [290.788796] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [290.788818] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [290.789051] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.790184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [290.790376] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [290.790753] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [290.791276] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [290.791284] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [290.791468] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [290.806756] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [290.806764] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [290.806973] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.807187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected

<7> [290.807218] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [290.807247] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [290.807266] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [290.807448] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.808048] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.808265] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] status updated from unknown to disconnected

<7> [290.808296] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [290.808320] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [290.808331] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [290.808335] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [290.808339] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [290.808445] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [290.808468] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [290.808502] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [290.808529] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [290.809603] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.809815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [290.810359] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [290.811014] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [290.811220] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [290.811419] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [290.812066] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.812497] [drm:drm_client_modeset_probe]

<7> [290.812763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [290.812814] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [290.813080] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.814319] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [290.814520] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [290.815667] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [290.816142] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [290.816150] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [290.816303] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [290.832582] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [290.832593] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [290.832769] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.833008] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [290.833035] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [290.833053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [290.833183] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.833898] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [290.834184] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [290.834314] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [290.834624] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [290.835052] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [290.835058] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [290.835207] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [290.849852] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [290.849868] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [290.849995] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.850127] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [290.850144] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [290.850156] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [290.850271] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.850876] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [290.851012] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [290.851027] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [290.851035] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [290.851038] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [290.851041] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [290.851129] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [290.851142] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [290.851176] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [290.851237] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [290.851398] [drm:drm_client_modeset_probe]

<7> [290.851452] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<6> [290.851389] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [290.851472] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [290.851626] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [290.851744] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [290.852271] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [290.852815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [290.853137] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10

<7> [290.853346] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [290.853499] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [290.853843] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [290.854033] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [290.854038] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [290.854148] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [290.857057] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [290.857063] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [290.857180] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [290.857196] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [290.857207] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [290.857526] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [290.857629] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [290.857929] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [290.858100] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [290.858106] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [290.858255] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [290.861208] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [290.861213] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [290.861324] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [290.861339] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [290.861351] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [290.861484] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [290.861496] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [290.861499] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [290.861502] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [290.861505] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [290.861521] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [290.861531] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [290.861550] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [290.861563] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<6> [290.880574] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC887-VD: line_outs=1 (0x14/0x0/0x0/0x0/0x0) type:line

<6> [290.880591] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)

<6> [290.880596] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x1b/0x0/0x0/0x0/0x0)

<6> [290.880600] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0

<6> [290.880604] snd_hda_codec_realtek hdaudioC0D0: dig-out=0x11/0x0

<6> [290.880607] snd_hda_codec_realtek hdaudioC0D0: inputs:

<6> [290.880611] snd_hda_codec_realtek hdaudioC0D0: Front Mic=0x19

<6> [290.880615] snd_hda_codec_realtek hdaudioC0D0: Rear Mic=0x18

<6> [290.880618] snd_hda_codec_realtek hdaudioC0D0: Line=0x1a

<7> [290.911001] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B

<7> [290.911150] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B

<7> [290.911268] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port B

<7> [290.911384] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C

<7> [290.911499] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C

<7> [290.911613] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port C

<7> [290.911727] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D

<7> [290.911842] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D

<7> [290.911974] i915 0000:00:02.0: [drm:i915_audio_component_get_eld [i915]] Not valid for port D

<6> [290.917109] input: HDA Intel PCH Front Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input86

<6> [290.919246] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input87

<6> [290.920059] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1f.3/sound/card0/input88

<6> [290.922829] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1f.3/sound/card0/input89

<6> [290.923701] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input90

<6> [290.924377] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input91

<6> [290.925146] input: HDA Intel PCH HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input92

<6> [290.925797] input: HDA Intel PCH HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:1f.3/sound/card0/input93

<7> [291.037163] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [291.037515] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [291.037694] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [291.037886] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [291.038493] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [291.113641] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [291.113779] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [291.114212] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [291.114749] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [291.114961] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [291.115079] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [291.115197] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [291.115313] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [291.136116] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]

<7> [291.173407] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper

<6> [291.710835] PM: suspend entry (s2idle)

<6> [291.713394] Filesystems sync: 0.002 seconds

<6> [291.715567] Freezing user space processes

<6> [291.720013] Freezing user space processes completed (elapsed 0.004 seconds)

<6> [291.720049] Freezing remaining freezable tasks

<6> [291.721112] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)

<6> [291.740272] e1000e: EEE TX LPI TIMER: 00000011

<5> [291.741828] sd 2:0:0:0: [sda] Synchronizing SCSI cache

<5> [291.741885] sd 2:0:0:0: [sda] Stopping disk

<7> [291.804970] PM: suspend of devices complete after 71.745 msecs

<7> [291.804989] PM: start suspend of devices complete after 83.794 msecs

<7> [291.810721] PM: late suspend of devices complete after 5.721 msecs

<7> [291.838496] PM: noirq suspend of devices complete after 23.834 msecs

<6> [291.842953] ACPI: \_SB_.PEPD: Successfully transitioned to state screen off

<6> [291.847847] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 entry

<7> [307.152927] Timekeeping suspended for 15.443 seconds

<7> [307.153114] PM: Triggering wakeup from IRQ 9

<7> [307.153456] ACPI: PM: ACPI fixed event wakeup

<7> [307.153474] PM: resume from suspend-to-idle

<6> [307.158398] ACPI: \_SB_.PEPD: Successfully transitioned to state lps0 exit

<6> [307.159325] ACPI: \_SB_.PEPD: Successfully transitioned to state screen on

<7> [307.172654] PM: noirq resume of devices complete after 13.322 msecs

<7> [307.175775] PM: early resume of devices complete after 1.547 msecs

<5> [307.178141] sd 2:0:0:0: [sda] Starting disk

<6> [307.187552] serial 00:02: activated

<6> [307.502634] ata6: SATA link down (SStatus 4 SControl 300)

<6> [307.502689] ata4: SATA link down (SStatus 4 SControl 300)

<6> [307.502745] ata2: SATA link down (SStatus 4 SControl 300)

<6> [307.502802] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300)

<6> [307.502908] ata5: SATA link down (SStatus 4 SControl 300)

<6> [307.502962] ata1: SATA link down (SStatus 4 SControl 300)

<6> [307.707096] ata3.00: configured for UDMA/133

<7> [307.707624] PM: resume of devices complete after 531.842 msecs

<6> [307.713466] Restarting tasks ... done.

<5> [307.715979] random: crng reseeded on system resumption

<5> [307.849760] Setting dangerous option enable_guc - tainting kernel

<7> [307.893742] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K

<7> [307.893955] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no)

<6> [307.894100] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A

<7> [307.894111] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH

<7> [307.894290] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [307.894582] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [307.894700] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 24000 kHz

<7> [307.895266] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [307.895393] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [307.895494] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M

<6> [307.895612] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [307.895616] i915 0000:00:02.0: vgaarb: deactivate vga console

<6> [307.896531] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [307.896551] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047

<7> [307.896707] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K

<7> [307.897014] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018

<7> [307.897172] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0

<7> [307.897299] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [307.897453] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [307.897591] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [307.901746] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483

<7> [307.901885] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [307.902013] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [307.902140] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [307.902267] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [307.902386] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [307.902532] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [307.902675] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no

<7> [307.902817] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [307.902959] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [307.903106] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no

<7> [307.903249] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [307.903368] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [307.903490] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [307.904045] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [307.904245] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206

<7> [307.904465] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [307.904660] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)

<7> [307.904802] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [307.904964] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [307.905156] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)

<7> [307.905399] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)

<7> [307.905602] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [307.905806] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)

<7> [307.905995] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [307.906143] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)

<7> [307.906307] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [307.906514] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [307.906709] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [307.906907] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [307.907109] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [307.907272] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [307.907433] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [307.907620] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4

<7> [307.907814] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [307.908008] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8

<7> [307.908203] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [307.908410] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0

<7> [307.908567] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02

<7> [307.908742] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [307.908995] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [307.909214] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO

<7> [307.909428] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [307.910161] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz

<7> [307.910371] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz

<7> [307.910583] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [307.910840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [307.911029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [307.911166] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [307.911343] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [307.911600] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [307.911796] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [307.911990] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [307.912188] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [307.912407] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin

<7> [307.913214] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<6> [307.913438] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)

<7> [307.913777] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV

<7> [307.913912] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us

<7> [307.914044] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [307.914173] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [307.914300] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [307.914470] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [307.914598] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [307.914758] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [307.914980] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [307.915190] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<7> [307.916832] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.

<7> [307.918518] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0

<7> [307.918801] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind

<6> [307.919011] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

<7> [307.919179] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port A is not present

<7> [307.919422] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (platform default)

<7> [307.919620] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B]

<7> [307.919799] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT)

<7> [307.920211] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:104:DDI C/PHY C] using AUX C (platform default)

<7> [307.920392] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C]

<7> [307.920541] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT)

<7> [307.920736] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present

<7> [307.920892] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] using AUX A (VBT)

<7> [307.921031] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E]

<7> [307.921313] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [307.921796] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled

<7> [307.921960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled

<7> [307.922117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled

<7> [307.922298] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [307.922508] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A

<7> [307.922676] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A

<7> [307.922814] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B

<7> [307.922955] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B

<7> [307.923091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B

<7> [307.923229] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C

<7> [307.923433] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C

<7> [307.923625] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C

<7> [307.923765] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [307.923902] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A

<7> [307.924038] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A

<7> [307.924175] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1

<7> [307.924319] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [307.924501] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [307.924679] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [307.924906] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled

<7> [307.925053] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled

<7> [307.925197] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled

<7> [307.925328] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [307.925477] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz

<7> [307.925651] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz

<7> [307.925829] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [307.925985] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz

<7> [307.926117] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz

<7> [307.926248] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz

<7> [307.926535] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [307.926715] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz

<7> [307.926899] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz

<7> [307.927039] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz

<7> [307.927170] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [307.927332] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]

<7> [307.927485] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]

<7> [307.927622] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]

<7> [307.927779] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling

<7> [307.927945] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [307.928127] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [307.928276] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [307.930975] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] GuC WOPCM is already locked [240K, 784K)

<7> [307.931108] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [307.931216] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]

<7> [307.931330] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0

<7> [307.931469] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global

<7> [307.932598] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0

<7> [307.932734] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0

<7> [307.932863] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0

<7> [307.935447] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)

<7> [307.935620] i915 0000:00:02.0: [drm:intel_guc_capture_init [i915]] GT0: GUC: capture found 6 ext-regs.

<7> [307.935773] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset

<7> [307.962314] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f

<7> [307.962488] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0

<7> [307.962619] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000

<7> [307.962749] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3

<7> [307.962878] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a

<7> [307.963006] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004

<7> [307.963135] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0

<7> [307.963264] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0

<7> [307.963401] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0

<7> [307.963531] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0

<7> [307.963660] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0

<7> [307.963789] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0

<7> [307.963918] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0

<7> [307.964046] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0

<7> [307.964177] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no

<6> [307.965409] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1

<6> [307.965413] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0

<7> [307.972323] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 5ms, freq = 350MHz, before = 350MHz, status = 0x8002F0EC, count = 0, ret = 0

<7> [307.972997] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<6> [307.973143] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled

<6> [307.973146] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled

<7> [307.980150] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV

<7> [307.980407] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping

<7> [307.980539] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping

<7> [307.980666] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping

<7> [307.980794] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [307.980940] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [307.981410] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [307.981515] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [307.981613] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [307.981710] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [307.985318] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event

<7> [307.985719] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event

<7> [307.986089] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1

<7> [307.987035] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event

<6> [307.987109] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [307.989281] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected

<6> [308.007544] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [308.008900] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input94

<7> [308.009775] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)

<7> [308.010642] [drm:drm_client_modeset_probe]

<7> [308.010560] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D

<7> [308.010795] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C

<7> [308.010988] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [308.010998] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B

<7> [308.011031] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [308.011199] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E

<7> [308.011945] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [308.012144] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9

<7> [308.012150] i915 device info: graphics version: 9

<7> [308.012153] i915 device info: media version: 9

<7> [308.012156] i915 device info: display version: 9

<7> [308.012160] i915 device info: graphics stepping: F0

<7> [308.012163] i915 device info: media stepping: F0

<7> [308.012166] i915 device info: display stepping: C0

<7> [308.012169] i915 device info: base die stepping: **

<7> [308.012172] i915 device info: gt: 2

<7> [308.012176] i915 device info: memory-regions: 0x21

<7> [308.012179] i915 device info: page-sizes: 0x11000

<7> [308.012182] i915 device info: platform: KABYLAKE

<7> [308.012185] i915 device info: ppgtt-size: 48

<7> [308.012189] i915 device info: ppgtt-type: 2

<7> [308.012192] i915 device info: dma_mask_size: 39

<7> [308.012195] i915 device info: is_mobile: no

<7> [308.012198] i915 device info: is_lp: no

<7> [308.012201] i915 device info: require_force_probe: no

<7> [308.012205] i915 device info: is_dgfx: no

<7> [308.012208] i915 device info: has_64bit_reloc: yes

<7> [308.012211] i915 device info: has_64k_pages: no

<7> [308.012214] i915 device info: gpu_reset_clobbers_display: no

<7> [308.012217] i915 device info: has_reset_engine: yes

<7> [308.012221] i915 device info: has_3d_pipeline: yes

<7> [308.012224] i915 device info: has_4tile: no

<7> [308.012227] i915 device info: has_flat_ccs: no

<7> [308.012230] i915 device info: has_global_mocs: no

<7> [308.012233] i915 device info: has_gmd_id: no

<7> [308.012236] i915 device info: has_gt_uc: yes

<7> [308.012240] i915 device info: has_heci_pxp: no

<7> [308.012243] i915 device info: has_heci_gscfi: no

<7> [308.012246] i915 device info: has_guc_deprivilege: no

<7> [308.012249] i915 device info: has_l3_ccs_read: no

<7> [308.012252] i915 device info: has_l3_dpf: no

<7> [308.012255] i915 device info: has_llc: yes

<7> [308.012258] i915 device info: has_logical_ring_contexts: yes

<7> [308.012262] i915 device info: has_logical_ring_elsq: no

<7> [308.012265] i915 device info: has_media_ratio_mode: no

<7> [308.012268] i915 device info: has_mslice_steering: no

<7> [308.012271] i915 device info: has_oa_bpc_reporting: no

<7> [308.012274] i915 device info: has_oa_slice_contrib_limits: no

<7> [308.012278] i915 device info: has_oam: no

<7> [308.012281] i915 device info: has_one_eu_per_fuse_bit: no

<7> [308.012284] i915 device info: has_pxp: no

<7> [308.012287] i915 device info: has_rc6: yes

<7> [308.012290] i915 device info: has_rc6p: no

<7> [308.012293] i915 device info: has_rps: yes

<7> [308.012297] i915 device info: has_runtime_pm: yes

<7> [308.012300] i915 device info: has_snoop: no

<7> [308.012303] i915 device info: has_coherent_ggtt: yes

<7> [308.012306] i915 device info: tuning_thread_rr_after_dep: no

<7> [308.012309] i915 device info: unfenced_needs_alignment: no

<7> [308.012312] i915 device info: hws_needs_physical: no

<7> [308.012315] i915 device info: has_pooled_eu: no

<7> [308.012318] i915 device info: cursor_needs_physical: no

<7> [308.012321] i915 device info: has_cdclk_crawl: no

<7> [308.012324] i915 device info: has_cdclk_squash: no

<7> [308.012327] i915 device info: has_ddi: yes

<7> [308.012331] i915 device info: has_dp_mst: yes

<7> [308.012334] i915 device info: has_dsb: no

<7> [308.012337] i915 device info: has_fpga_dbg: yes

<7> [308.012340] i915 device info: has_gmch: no

<7> [308.012343] i915 device info: has_hotplug: yes

<7> [308.012346] i915 device info: has_hti: no

<7> [308.012390] i915 device info: has_ipc: yes

<7> [308.012395] i915 device info: has_overlay: no

<7> [308.012398] i915 device info: has_psr: yes

<7> [308.012400] i915 device info: has_psr_hw_tracking: yes

<7> [308.012403] i915 device info: overlay_needs_physical: no

<7> [308.012406] i915 device info: supports_tv: no

<7> [308.012408] i915 device info: has_hdcp: yes

<7> [308.012411] i915 device info: has_dmc: yes

<7> [308.012413] i915 device info: has_dsc: no

<7> [308.012416] i915 device info: rawclk rate: 24000 kHz

<7> [308.012419] i915 device info: iommu: enabled

<7> [308.012422] i915 device info: available engines: 40403

<7> [308.012425] i915 device info: slice total: 1, mask=0001

<7> [308.012428] i915 device info: subslice total: 3

<7> [308.012430] i915 device info: slice0: 3 subslices, mask=00000007

<7> [308.012433] i915 device info: slice1: 0 subslices, mask=00000000

<7> [308.012436] i915 device info: slice2: 0 subslices, mask=00000000

<7> [308.012439] i915 device info: EU total: 24

<7> [308.012441] i915 device info: EU per subslice: 8

<7> [308.012444] i915 device info: has slice power gating: no

<7> [308.012446] i915 device info: has subslice power gating: no

<7> [308.012448] i915 device info: has EU power gating: yes

<6> [308.012451] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled

<6> [308.012454] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [308.012456] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [308.012378] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [308.012576] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [308.012990] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [308.013168] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [308.013174] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [308.013300] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [308.016716] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [308.016725] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [308.016964] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [308.017343] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [308.017568] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [308.017769] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [308.018416] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [308.019055] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected

<7> [308.019411] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [308.019437] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [308.019456] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [308.019673] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [308.021345] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [308.021522] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [308.021860] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [308.022287] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [308.022293] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [308.022439] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [308.037718] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [308.037726] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [308.037883] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [308.038036] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected

<7> [308.038057] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [308.038075] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [308.038086] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [308.038227] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [308.038809] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [308.038971] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] status updated from unknown to disconnected

<7> [308.038990] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [308.039006] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [308.039015] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [308.039018] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [308.039021] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [308.039113] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [308.039132] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [308.039157] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [308.039176] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [308.040162] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [308.040322] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [308.040812] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [308.041452] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [308.041638] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [308.041829] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [308.042453] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [308.042774] [drm:drm_client_modeset_probe]

<7> [308.042990] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [308.043055] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [308.043291] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [308.044626] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [308.044776] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [308.045424] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [308.045916] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [308.045922] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [308.046029] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<6> [308.051634] [IGT] i915_suspend: finished subtest basic-s2idle-without-i915, SUCCESS

<7> [308.051702] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [308.052449] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

<7> [308.052672] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<6> [308.053614] [IGT] i915_suspend: exiting, ret=0

<7> [308.053831] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Results for igt@i915_suspend@basic-s2idle-without-i915