Results for igt@kms_force_connector_basic@prune-stale-modes

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

pstore0-1689547479_Oops_1

DetailValue
Igt-Version 
IGT-Version: 1.27.1-gfaa966f69 (x86_64) (Linux: 6.5.0-rc2-linus-v6.5-rc2-gfdf0eaf11452+ x86_64)
Out 
Opened device: /dev/dri/card0
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.563s)
Err 
Starting subtest: prune-stale-modes
Subtest prune-stale-modes: SUCCESS (0.563s)
Dmesg
<6> [163.572638] Console: switching to colour dummy device 80x25
<6> [163.572875] [IGT] kms_force_connector_basic: executing
<7> [163.576440] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [163.576927] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [163.577075] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [163.577561] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [163.577568] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [163.577585] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [163.628127] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [163.645288] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.645294] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [163.645401] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [163.662238] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.662243] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [163.662341] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [163.662396] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [163.662412] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [163.713095] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [163.730273] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.730277] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [163.730381] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [163.747267] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.747270] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [163.747372] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [163.747433] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [163.747448] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [163.798123] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [163.815270] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.815274] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [163.815376] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [163.832246] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.832249] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [163.832345] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [163.832581] [IGT] kms_force_connector_basic: starting subtest prune-stale-modes
<7> [163.832681] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 2 or reprobing
<7> [163.832686] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [163.832698] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [163.884121] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [163.901209] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.901230] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [163.901458] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [163.918243] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.918252] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [163.918351] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from disconnected to connected
<7> [163.918475] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [163.918488] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [163.918494] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [163.918498] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [163.918501] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [163.918504] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [163.918543] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [163.918558] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [163.970132] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [163.987266] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [163.987280] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [163.987440] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.004230] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.004236] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.004368] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.004380] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.004384] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.004387] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.004389] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.004392] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.004567] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [164.004588] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.004603] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.004737] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [164.004740] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [164.056125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.073218] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [164.073302] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.073308] [drm:drm_mode_prune_invalid] Not using 800x600 mode: STALE
<7> [164.073313] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.073317] [drm:drm_mode_prune_invalid] Not using 848x480 mode: STALE
<7> [164.073323] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.073337] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [164.073340] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x40 0xa
<7> [164.073344] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [164.073347] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.073349] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.073352] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.073465] i915 0000:00:02.0: [drm:drm_edid_override_set] [CONNECTOR:258:HDMI-A-1] EDID override set
<7> [164.073510] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.073522] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.073656] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD monitor IGT
<7> [164.073659] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:258:HDMI-A-1] ELD size 24, SAD count 0
<7> [164.073662] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 4
<7> [164.124118] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.141232] i915 0000:00:02.0: [drm:drm_dp_dual_mode_detect [drm_display_helper]] DP dual mode HDMI ID: (err -6)
<7> [164.141311] [drm:drm_mode_debug_printmodeline] Modeline "1400x1050": 60 101000 1400 1448 1480 1560 1050 1053 1057 1080 0x48 0xa
<7> [164.141317] [drm:drm_mode_prune_invalid] Not using 1400x1050 mode: STALE
<7> [164.141323] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.141338] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [164.141341] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [164.141345] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.141348] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.141351] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.141472] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [164.141493] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.141506] i915 0000:00:02.0: [drm:intel_hdmi_force [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.192120] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.209271] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.209281] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.209414] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.226252] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.226258] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.226350] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:258:HDMI-A-1] EDID changed, epoch counter 5
<7> [164.226386] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 148500 1920 2008 2052 2200 1080 1084 1089 1125 0x48 0xa
<7> [164.226390] [drm:drm_mode_prune_invalid] Not using 1920x1080 mode: STALE
<7> [164.226394] [drm:drm_mode_debug_printmodeline] Modeline "1280x720": 60 74250 1280 1390 1430 1650 720 725 730 750 0x40 0x5
<7> [164.226397] [drm:drm_mode_prune_invalid] Not using 1280x720 mode: STALE
<7> [164.226402] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] probed modes :
<7> [164.226413] [drm:drm_mode_debug_printmodeline] Modeline "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x40 0xa
<7> [164.226416] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 60 40000 800 840 968 1056 600 601 605 628 0x40 0x5
<7> [164.226418] [drm:drm_mode_debug_printmodeline] Modeline "800x600": 56 36000 800 824 896 1024 600 601 603 625 0x40 0x5
<7> [164.226421] [drm:drm_mode_debug_printmodeline] Modeline "848x480": 60 33750 848 864 976 1088 480 486 494 517 0x40 0x5
<7> [164.226423] [drm:drm_mode_debug_printmodeline] Modeline "640x480": 60 25175 640 656 752 800 480 490 492 525 0x40 0xa
<7> [164.226537] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 2 to 0 or reprobing
<7> [164.226542] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.226553] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.277134] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.294206] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.294210] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.294311] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.310217] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.310220] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.310316] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] status updated from connected to disconnected
<7> [164.310335] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.310457] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.310473] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.362127] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.379236] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.379240] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.379345] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.395259] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.395263] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.395360] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<6> [164.395648] [IGT] kms_force_connector_basic: finished subtest prune-stale-modes, SUCCESS
<7> [164.395754] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [164.396146] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [164.396151] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.396165] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.396952] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.397059] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.397687] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.397785] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.397886] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.397994] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.398106] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.398110] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.398113] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.398116] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.398129] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.398221] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.398948] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.399042] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.399718] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.399730] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.399734] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.399761] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.399776] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.400631] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.400729] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.401336] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.401432] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.401526] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.401618] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.401723] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.401727] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.401730] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.401732] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.401742] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.401833] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.402647] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.402747] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.403406] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.403417] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.403421] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.403501] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:236:eDP-1] EDID override reset
<7> [164.403518] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.403531] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.404337] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.404435] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.405026] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.405119] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.405211] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.405300] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.405403] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.405407] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.405410] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.405412] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.405421] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.405512] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.406317] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.406417] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.407069] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.407080] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.407084] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.407170] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:246:DP-1] EDID override reset
<7> [164.407185] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [164.407198] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [164.407366] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [164.407462] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [164.407466] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.407477] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.458107] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.474221] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.474226] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.474336] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.491200] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.491204] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.491300] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.491351] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.491367] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.542138] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.559260] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.559264] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.559368] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.576244] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.576248] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.576341] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.576453] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:258:HDMI-A-1] EDID override reset
<7> [164.576472] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.576487] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.627119] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.644228] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.644232] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.644333] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.660216] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.660219] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.660314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.660441] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:264:DP-2] EDID override reset
<7> [164.660461] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2]
<7> [164.660476] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [164.660652] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2] disconnected
<7> [164.660726] i915 0000:00:02.0: [drm:drm_edid_override_reset] [CONNECTOR:273:DP-3] EDID override reset
<7> [164.660739] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3]
<7> [164.660748] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [164.660886] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3] disconnected
<6> [164.661282] [IGT] kms_force_connector_basic: exiting, ret=0
<7> [164.661363] [drm:status_store] [CONNECTOR:258:HDMI-A-1] force updated from 0 to 0 or reprobing
<7> [164.661368] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.661379] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.712126] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.729259] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.729263] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.729366] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.746212] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.746215] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.746311] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.746380] [drm:status_store] [CONNECTOR:236:eDP-1] force updated from 0 to 0 or reprobing
<7> [164.746386] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.746403] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.747219] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.747316] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.747943] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.748041] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.748135] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.748229] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.748341] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.748345] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.748348] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.748351] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.748364] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.748460] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.749253] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.749348] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.749990] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.750001] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.750005] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.750170] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [164.767137] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [164.767153] [drm:drm_client_modeset_probe]
<7> [164.767193] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1]
<7> [164.767213] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:236:eDP-1]
<7> [164.768134] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 01 11 00 02 01 00 01 80 06 01 06 00 08 00 00
<7> [164.768280] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0
<7> [164.769042] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:235:DDI B/PHY B] MST support: port: no, sink: no, modparam: yes
<7> [164.769357] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000
<7> [164.769670] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000
<7> [164.769999] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000
<7> [164.770318] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz
<7> [164.770331] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] Assigning EDID-1.4 digital sink color depth as 8 bpc.
<7> [164.770341] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD monitor
<7> [164.770349] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:236:eDP-1] ELD size 20, SAD count 0
<7> [164.770385] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] VRR capable: no
<7> [164.770651] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [164.771631] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [164.771759] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:236:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [164.772539] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:eDP-1] probed modes :
<7> [164.772554] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 60 138780 1920 1968 2000 2080 1080 1083 1088 1112 0x48 0xa
<7> [164.772559] [drm:drm_mode_debug_printmodeline] Modeline "1920x1080": 48 111040 1920 1968 2000 2080 1080 1083 1088 1112 0x40 0xa
<7> [164.772563] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [164.772577] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [164.772747] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [164.772761] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1]
<7> [164.772774] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:258:HDMI-A-1]
<7> [164.824125] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus tc2] timed out, falling back to bit banging on pin 10
<7> [164.841255] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.841260] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging
<7> [164.841376] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus tc2. force bit now 1
<7> [164.858275] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus tc2
<7> [164.858278] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus tc2. force bit now 0
<7> [164.858374] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:258:HDMI-A-1] disconnected
<7> [164.858386] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2]
<7> [164.858397] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:264:DP-2]
<7> [164.858533] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:264:DP-2] disconnected
<7> [164.858544] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3]
<7> [164.858554] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:273:DP-3]
<7> [164.858695] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:273:DP-3] disconnected
<7> [164.858706] [drm:drm_client_modeset_probe] connector 236 enabled? yes
<7> [164.858709] [drm:drm_client_modeset_probe] connector 246 enabled? no
<7> [164.858710] [drm:drm_client_modeset_probe] connector 258 enabled? no
<7> [164.858712] [drm:drm_client_modeset_probe] connector 264 enabled? no
<7> [164.858713] [drm:drm_client_modeset_probe] connector 273 enabled? no
<7> [164.858741] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [164.858751] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 236
<7> [164.858754] [drm:drm_client_modeset_probe] looking for preferred mode on connector 236 0
<7> [164.858756] [drm:drm_client_modeset_probe] found mode 1920x1080
<7> [164.858758] [drm:drm_client_modeset_probe] picking CRTCs for 1920x1080 config
<7> [164.858772] [drm:drm_client_modeset_probe] desired mode 1920x1080 set on crtc 80 (0,0)
<6> [164.884047] Console: switching to colour frame buffer device 240x67
Created at 2023-07-17 00:31:04