Results for igt@vgem_basic@unload

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gfaa966f69 (x86_64) (Linux: 6.5.0-rc2-linus-v6.5-rc2-gfdf0eaf11452+ x86_64)
Out	Starting subtest: unload Opened device: /dev/dri/card1 Subtest unload: SUCCESS (28.991s)
Err	Starting subtest: unload Subtest unload: SUCCESS (28.991s)
Dmesg	<6> [283.392908] Console: switching to colour dummy device 80x25 <6> [283.393844] [IGT] vgem_basic: executing <6> [283.404249] [IGT] vgem_basic: starting subtest unload <7> [283.404485] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [283.492656] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [283.514087] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 1 <7> [283.537319] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <4> [283.834799] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x200f0000 <4> [284.838779] snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x200f0000 <4> [285.843784] snd_hda_intel 0000:00:1f.3: Codec #2 probe error; disabling it... <6> [285.857795] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC700: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker <6> [285.857816] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) <6> [285.857823] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0) <6> [285.857828] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 <6> [285.857833] snd_hda_codec_realtek hdaudioC0D0: inputs: <6> [285.857838] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19 <7> [286.220598] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off <7> [286.221673] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067 <6> [286.634351] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0) <6> [286.661476] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input12 <6> [286.673857] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input13 <7> [286.676716] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3 <7> [286.677217] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [286.677611] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [286.677953] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [286.678268] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [293.120045] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [293.124645] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [293.125587] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [293.126444] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [293.127191] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [293.127973] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [293.128675] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [293.129180] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [293.129725] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [293.140325] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [293.140733] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [293.141037] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <6> [293.146057] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 1 <7> [293.168352] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [293.171122] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [293.171495] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [293.171856] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [293.172205] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [293.172949] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [293.173275] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [293.173614] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [293.173927] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [293.190529] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [293.190933] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [293.191286] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [302.764152] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [302.769156] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [302.769973] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [302.770801] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [302.771578] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [302.772052] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [302.772555] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [302.773028] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [302.773626] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [302.790338] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [302.790691] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [302.790980] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <6> [302.795792] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 1 <7> [302.817872] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [302.819955] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [302.820296] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [302.820681] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [302.821038] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [302.821362] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [302.821777] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [302.822089] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [302.822415] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [302.823632] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [302.823966] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [302.824260] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <6> [312.397617] [IGT] vgem_basic: finished subtest unload, SUCCESS <7> [312.397864] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [312.402459] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [312.403191] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [312.404021] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.404726] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [312.405196] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.405694] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [312.406168] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.406668] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [312.423721] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [312.424044] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [312.424329] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <6> [312.429107] [drm] Initialized vgem 1.0.0 20120112 for vgem on minor 1 <7> [312.451304] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [312.453478] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [312.453833] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [312.454182] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.455151] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [312.455557] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.455882] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [312.456187] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.456749] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [312.473894] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [312.474265] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [312.474612] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <6> [312.476663] [IGT] vgem_basic: exiting, ret=0 <7> [312.478920] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [312.479272] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [312.479653] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.480009] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [312.480326] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.480661] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [312.480969] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.481274] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [312.490451] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [312.490807] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [312.491092] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <6> [312.492002] Console: switching to colour frame buffer device 400x112 <7> [312.493139] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [312.493493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [312.493842] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.494186] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [312.494539] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.494860] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [312.495156] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [312.495482] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [312.507070] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [312.507443] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [312.507730] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

Created at 2023-07-17 00:31:04