Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-gfaa966f69 (x86_64) (Linux: 6.5.0-rc2-linus-v6.5-rc2-gfdf0eaf11452+ x86_64) |
| Out |
Starting subtest: basic-rte Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa3f/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 Subtest basic-rte: SUCCESS (1.776s) i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: no Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x79/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa3f/0xd20 [i915] intel_atomic_commit+0x381/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 |
| Err |
Starting subtest: basic-rte Subtest basic-rte: SUCCESS (1.776s) |
| Dmesg |
<6> [74.048781] Console: switching to colour dummy device 80x25
<6> [74.048877] [IGT] i915_pm_rpm: executing
<6> [74.054310] [IGT] i915_pm_rpm: starting subtest basic-rte
<7> [74.054349] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [74.054691] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1]
<7> [74.054707] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [74.054838] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.055747] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.055881] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] disconnected
<7> [74.055951] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [74.055961] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [74.056073] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.056768] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.056882] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [74.056940] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2]
<7> [74.056949] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [74.057045] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.057985] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.058106] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] disconnected
<7> [74.058160] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3]
<7> [74.058170] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [74.058283] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.059161] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.059281] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] disconnected
<7> [74.059337] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2]
<7> [74.059346] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [74.059455] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.060354] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.060466] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2] disconnected
<7> [74.060516] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4]
<7> [74.060526] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [74.060619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.061553] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.061665] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] disconnected
<7> [74.066658] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1]
<7> [74.066673] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [74.066790] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.067495] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.067645] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] disconnected
<7> [74.068007] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [74.068017] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [74.068122] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.068819] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.068931] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [74.069290] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2]
<7> [74.069300] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [74.069400] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.070097] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.070227] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] disconnected
<7> [74.070601] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3]
<7> [74.070611] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [74.070708] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.071405] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.071522] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] disconnected
<7> [74.071868] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2]
<7> [74.071878] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [74.071977] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.072672] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.072790] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2] disconnected
<7> [74.073138] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4]
<7> [74.073148] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [74.073255] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.073956] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.074070] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] disconnected
<7> [74.074581] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1]
<7> [74.074591] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [74.074690] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.075386] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.075497] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] disconnected
<7> [74.075522] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1]
<7> [74.075532] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [74.075627] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.076576] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.076694] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:246:DP-1] disconnected
<7> [74.076718] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2]
<7> [74.076728] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [74.076825] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.077774] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.077892] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] disconnected
<7> [74.077913] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3]
<7> [74.077925] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [74.078024] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.078967] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.079079] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] disconnected
<7> [74.079100] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2]
<7> [74.079112] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [74.079225] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.080153] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.080270] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:DP-2] disconnected
<7> [74.080290] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4]
<7> [74.080299] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [74.080397] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [74.081357] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [74.081474] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] disconnected
<7> [75.082829] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.086279] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.089860] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.091067] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.091210] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.091338] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.091460] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.091579] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.091698] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.091816] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.091937] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.092055] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.092173] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.092336] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.092521] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.094053] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.094390] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.094718] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.094972] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.095276] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.119351] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.119576] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.119959] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.120395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.121200] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.121566] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.122016] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.123008] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.124801] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.125115] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.138572] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.139785] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [75.140873] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.140950] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.142098] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.142234] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [75.142251] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [75.142352] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.143326] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [75.143286] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.143408] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [75.143495] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.143619] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.144461] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.145681] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.145805] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.145927] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.146046] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.146165] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.146309] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.146425] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.146545] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.146654] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.146767] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.146877] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.146983] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.147083] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.148296] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.148415] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.148497] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [75.148495] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [75.150729] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.153152] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.154300] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.154428] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.154544] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.154657] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.154771] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.154885] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.154998] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.155115] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.155241] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.155357] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.155491] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.155665] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.157201] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.157349] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.157497] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.157600] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.157728] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.181840] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.181967] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.182199] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.182429] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.182997] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.183206] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.183397] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.183644] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.184682] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.184843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.196997] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.199304] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.199373] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.200558] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.200745] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [75.200761] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [75.200895] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.201743] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.201893] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [75.202088] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.204135] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.206514] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.207691] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.207829] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.207950] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.208076] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.208213] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.208337] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.208455] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.208574] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.208690] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.208806] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.208941] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.209114] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.210731] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.210900] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.211059] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.211171] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.211319] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.235776] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.235996] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.236410] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.236771] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.237613] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.237916] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.238242] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.238606] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.240100] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.240348] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.252625] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.253828] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.253924] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.254057] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.254935] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.256153] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.256286] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.256395] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.256505] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.256614] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.256727] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.256839] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.256952] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.257059] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.257164] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.257282] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.257411] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.257532] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.258738] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.258851] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.259711] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [75.259789] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [75.261168] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.263554] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.264745] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.264871] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.264986] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.265098] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.265218] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.265336] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.265448] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.265563] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.265670] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.265776] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.265902] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.266072] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.267607] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.267760] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.267908] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.268008] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.268132] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.291358] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.291499] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.291739] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.291994] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.292616] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.292990] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.293230] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.293552] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.294779] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.294970] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.308308] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.310616] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.310697] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.311835] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.311966] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [75.311994] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [75.312101] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.313027] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.313236] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [75.313240] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.313388] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.314212] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.315429] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.315580] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.315701] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.315876] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.316042] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.316187] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.316332] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.316461] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.316582] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.316709] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.316827] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.316934] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.317033] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.318269] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.318434] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [75.318410] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.320708] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.323095] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.324265] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.324404] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.324528] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.324651] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.324771] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.324889] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.325006] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.325127] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.325262] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.325386] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.325525] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.325713] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.327226] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.327386] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.327540] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.327646] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.327777] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.352446] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.352597] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.352849] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.353111] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.353769] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.354205] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.354509] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.354822] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.356085] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.356311] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.369637] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.370834] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.370930] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.371072] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.371935] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.373173] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.373359] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.373476] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.373588] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.373705] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.373815] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.373925] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.374052] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.374166] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.374293] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.374421] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.374568] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.374681] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.375886] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.376007] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.377284] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [75.379542] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.381931] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.383074] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.383229] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.383349] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.383463] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.383576] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.383689] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.383802] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.383919] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.384036] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.384151] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.384291] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.384491] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.385880] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.386034] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.386185] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.386290] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.386417] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.411059] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.411266] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.411547] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.411851] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.412542] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.412902] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.413176] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.413627] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.415077] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.415310] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.428764] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.429966] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.430044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.431087] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.431210] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [75.431224] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [75.431325] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.432280] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.432397] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [75.432410] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [75.432508] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.433478] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.433595] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [75.433607] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [75.433708] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.434673] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.434784] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [75.434796] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [75.434893] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.435860] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.435976] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [75.435988] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [75.436086] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.437054] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.437166] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [75.437187] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [75.437292] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.438261] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.438377] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [75.438388] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [75.438480] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.439443] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.439554] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [75.439565] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [75.439653] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.440642] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.440769] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [75.440781] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [75.440877] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.441832] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.441943] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [75.441955] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [75.442050] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.443021] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.443132] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [75.443143] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [75.443254] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.444240] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.444348] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [75.444361] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.446630] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.449019] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.450199] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.450324] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.450440] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.450555] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.450667] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.450780] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.450891] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.451006] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.451116] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.451242] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.451378] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.451588] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.453098] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.453248] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.453391] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.453485] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.453607] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.479679] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [75.492045] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.492380] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.492838] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.493325] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.494222] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.494682] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.495103] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.495606] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.497287] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.497395] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.509495] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.511806] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.511911] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.512055] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.513000] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.514222] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.514353] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.514475] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.514598] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.514722] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.514842] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.514960] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.515081] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.515205] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.515326] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.515438] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.515547] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.515650] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.516857] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.516981] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.517549] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [75.520518] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.522883] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.524046] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.524197] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.524321] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.524444] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.524563] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.524681] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.524798] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.524918] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.525032] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.525149] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.525294] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.525500] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.526879] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.527037] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.527191] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.527295] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.527425] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.552111] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.552325] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.552621] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.552917] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.553578] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.553907] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.554167] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.554527] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.555918] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.556139] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.569499] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.571824] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.572003] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.572211] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.572983] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.574214] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.574386] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.574531] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.574675] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.574813] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.574944] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.575070] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.575207] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.575337] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.575493] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.575612] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.575723] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.575829] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.577040] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.577168] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.577891] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [75.577280] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [75.579470] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.581847] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.583034] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.583157] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.583287] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.583409] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.583522] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.583634] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.583747] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.583861] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.583973] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.584083] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.584226] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.584409] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.585922] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.586070] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.586222] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.586326] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.586452] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.611083] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.611281] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.611551] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.611843] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.612517] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.612813] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.613077] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.613437] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.614763] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.614970] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.628337] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.629545] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.629613] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.630676] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.630797] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [75.630814] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [75.630919] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.631863] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.631985] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [75.632062] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.632223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.633029] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.634257] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.634430] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.634589] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.634719] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.634865] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.634983] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.635099] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.635235] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.635354] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.635475] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.635643] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.635808] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.635931] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.637144] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.637294] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.637327] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [75.639620] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.641967] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.643133] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.643271] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.643402] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.643527] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.643648] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.643767] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.643884] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.644004] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.644121] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.644249] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.644386] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.644581] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.646096] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.646263] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.646417] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.646523] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.646651] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.671318] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.671469] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.671725] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.671999] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.672652] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.672996] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.673258] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.673562] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.674824] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.675022] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.688499] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.689700] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.689792] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.689920] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.690806] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.692027] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.692150] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.692273] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.692391] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.692507] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.692621] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.692734] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.692848] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.692960] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.693071] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.693183] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.693288] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.693386] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.694589] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.694702] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.695396] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [75.697026] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.699415] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.700582] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.700704] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.700822] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.700935] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.701049] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.701162] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.701294] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.701411] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.701527] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.701644] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.701775] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.701973] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.703228] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.703388] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.703532] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.703628] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.703747] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.728432] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.728585] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.728837] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.729115] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.729812] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.730103] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.730363] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.730676] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.731923] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.732112] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.745504] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.746708] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.746796] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.747844] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.747964] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [75.747977] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [75.748071] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.749036] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.749157] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [75.749169] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [75.749280] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.750236] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.750358] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [75.750369] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [75.750458] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.751419] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.751540] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [75.751556] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [75.751653] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.752607] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.752718] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [75.752729] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [75.752822] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.753798] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.753908] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [75.753919] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [75.754010] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.754994] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.755106] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [75.755118] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [75.755223] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.756186] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.756297] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [75.756309] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [75.756401] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.757378] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.757481] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [75.757495] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [75.757586] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.758577] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.758687] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [75.758700] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.760984] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.763413] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.764547] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.764674] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.764790] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.764906] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.765024] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.765138] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.765261] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.765377] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.765489] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.765600] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.765727] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.765909] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.767220] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.767370] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.767518] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.767618] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.767744] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.808013] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.808453] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.809080] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.809763] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.810979] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.811578] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.812105] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.813154] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.813859] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.813964] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.826001] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.827200] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [75.828300] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.828398] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.829528] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [75.829546] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [75.829682] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [75.829694] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [75.830711] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [75.830721] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<6> [75.830871] [IGT] i915_pm_rpm: finished subtest basic-rte, SUCCESS
<7> [75.830888] [drm:drm_mode_setcrtc] [CRTC:80:pipe A]
<7> [75.831905] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.832031] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [75.832096] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.832229] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.833071] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.834300] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.834424] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.834540] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.834657] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.834776] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.834894] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.835012] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.835133] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.835271] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.835393] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.835507] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.835613] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.835716] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.836937] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.837096] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.838127] [drm:drm_mode_setcrtc] [CRTC:131:pipe B]
<7> [75.838140] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [75.840582] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.842944] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.844113] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.844249] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.844371] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.844486] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.844600] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.844715] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.844829] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.844950] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.845065] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.845186] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.845341] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.845530] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.847036] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.847195] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.847356] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.847463] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.847592] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.872267] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.872419] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.872672] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.872936] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.873613] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.873861] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.874083] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.874473] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.875723] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.875903] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.889312] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.890517] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.890581] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.891642] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.891777] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [75.891862] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.891989] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.892821] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.894036] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.894159] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.894291] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.894413] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.894527] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.894645] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.894761] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.894878] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.894991] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.895103] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.895218] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.895339] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.895441] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.896651] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.896769] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.897641] [drm:drm_mode_setcrtc] [CRTC:182:pipe C]
<7> [75.899082] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.901474] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.902645] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.902764] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.902886] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.903012] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.903137] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.903276] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.903396] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.903518] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.903630] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.903742] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.903869] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.904046] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.905584] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.905736] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.905884] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.905986] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.906110] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.930757] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.930914] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.931213] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.931497] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.932125] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.932391] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.932625] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.932912] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.934107] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.934307] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.946498] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [75.947706] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [75.947820] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [75.947972] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [75.948804] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.950023] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.950148] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.950279] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.950401] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.950521] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.950639] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.950758] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.950885] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.951004] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.951122] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.951243] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [75.951379] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.951486] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [75.952693] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [75.952820] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [75.953458] [drm:drm_mode_setcrtc] [CRTC:233:pipe D]
<7> [75.953538] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [75.955123] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [75.957503] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [75.958689] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.958814] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [75.958935] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.959054] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [75.959172] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.959307] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [75.959432] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.959555] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [75.959674] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.959791] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [75.959925] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [75.960102] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [75.961648] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [75.961804] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [75.961956] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [75.962061] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [75.962198] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [75.986858] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [75.987019] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [75.987323] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [75.987691] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [75.988418] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [75.988665] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [75.988887] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [75.989221] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [75.990469] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [75.990657] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.004031] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [76.005238] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [76.005308] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.006364] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.006496] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [76.006514] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [76.006607] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.007558] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.007687] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [76.007771] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.007969] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [76.008726] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.009947] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.010080] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.010214] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.010342] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.010463] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.010585] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.010707] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.010830] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.010948] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.011068] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.011189] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [76.011310] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.011419] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.012630] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.012751] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [76.013350] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [76.015065] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [76.017456] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.018623] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.018752] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.018880] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.018999] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.019118] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.019245] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.019373] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.019499] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.019615] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.019731] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.019866] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [76.020069] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [76.021612] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [76.021767] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.021920] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [76.022030] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [76.022164] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [76.046928] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [76.047074] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [76.047347] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [76.047662] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [76.048354] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [76.048596] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [76.048807] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [76.049067] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [76.050280] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.050448] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.063836] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [76.065041] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [76.065107] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.066163] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.066299] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [76.066313] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [76.066408] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.067363] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.067486] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [76.067502] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [76.067593] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.068552] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.068668] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [76.068685] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [76.068783] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.069744] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.069861] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [76.069877] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [76.069970] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.070955] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.071077] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [76.071100] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [76.071202] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.072133] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.072252] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [76.072263] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [76.072370] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.073323] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.073436] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [76.073453] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [76.073562] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.074528] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.074656] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [76.074669] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [76.074759] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.075723] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.075850] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [76.075867] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [76.075962] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.076921] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.077041] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [76.077053] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [76.077154] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.078111] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.078239] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [76.078252] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Suspending device
<7> [76.080516] i915 0000:00:02.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled
<7> [76.082940] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.084079] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.084228] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.084347] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.084462] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.084575] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.084689] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.084802] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.084918] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.085030] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.085145] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.085285] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0
<7> [76.085476] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_1
<7> [76.086881] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0)
<7> [76.087029] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.087174] i915 0000:00:02.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9
<7> [76.087302] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08
<7> [76.087445] i915 0000:00:02.0: [drm:intel_runtime_suspend [i915]] Device suspended
<7> [76.140433] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Resuming device
<7> [76.140789] i915 0000:00:02.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9
<7> [76.141457] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00
<7> [76.142071] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [76.143296] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [76.144103] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0
<7> [76.144862] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os
<7> [76.145661] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [76.148432] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.149177] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.170127] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled
<7> [76.172501] i915 0000:00:02.0: [drm:intel_runtime_resume [i915]] Device resumed
<7> [76.172500] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:236:HDMI-A-1]
<7> [76.172644] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.172770] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [76.173694] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.174913] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.175051] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.175189] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.175318] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.175440] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.175560] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.175680] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.175805] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.175925] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.176049] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.176158] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [76.176302] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [76.176483] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:236:HDMI-A-1] Same epoch counter 6
<7> [76.176433] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010
<7> [76.176503] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:246:DP-1]
<7> [76.176661] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:246:DP-1] Same epoch counter 1
<7> [76.176673] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:255:HDMI-A-2]
<7> [76.176799] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:255:HDMI-A-2] Same epoch counter 1
<7> [76.176809] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:259:HDMI-A-3]
<7> [76.176922] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:259:HDMI-A-3] Same epoch counter 1
<7> [76.176932] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:263:DP-2]
<7> [76.177048] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:263:DP-2] Same epoch counter 1
<7> [76.177058] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:271:HDMI-A-4]
<7> [76.177172] i915 0000:00:02.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:271:HDMI-A-4] Same epoch counter 1
<7> [76.188154] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [76.188365] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [76.188476] i915 0000:00:02.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_2 forced on (bios:1 driver:0 kvmr:0 debug:0)
<7> [76.188572] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [76.188672] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.188766] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.189970] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<7> [76.232719] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.233382] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [76.234567] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.235835] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.236408] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.236869] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.237377] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.237787] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.238227] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.238598] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.238969] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.239394] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.239749] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.240116] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [76.240454] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.240749] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.242290] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [76.243206] [IGT] i915_pm_rpm: exiting, ret=0
<7> [76.244645] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.244850] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [76.245614] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.246836] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.246997] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.247146] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.247306] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.247447] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.247584] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.247711] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.247840] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.247965] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.248092] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.248245] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [76.248361] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.248464] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.249678] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
<6> [76.249902] Console: switching to colour frame buffer device 128x48
<7> [76.250249] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [76.250376] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [76.251036] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [76.251167] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.251313] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [76.251442] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.251558] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [76.251673] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.251786] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [76.251898] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.252014] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it.
<7> [76.252126] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY E Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [76.252258] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY E already enabled, won't reprogram it.
<7> [76.252401] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [76.252537] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [76.252645] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [76.253852] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on
|