Result:
git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0
| Detail | Value |
|---|---|
| Igt-Version |
IGT-Version: 1.27.1-gd1574543b (x86_64) (Linux: 6.5.0-rc1-linus-v6.5-rc1-g06c2afb862f9+ x86_64) |
| Out |
Starting subtest: basic-s3-without-i915 Opened device: /dev/dri/card0 [cmd] rtcwake: wakeup from "mem" using /dev/rtc0 at Sun Jul 9 21:33:42 2023 Subtest basic-s3-without-i915: SUCCESS (7.124s) |
| Err |
Starting subtest: basic-s3-without-i915 Subtest basic-s3-without-i915: SUCCESS (7.124s) |
| Dmesg |
<6> [572.327303] Console: switching to colour dummy device 80x25
<6> [572.328524] [IGT] i915_suspend: executing
<6> [572.341825] [IGT] i915_suspend: starting subtest basic-s3-without-i915
<7> [572.341973] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<6> [572.371651] [IGT] Unloading i915
<4> [573.168715] snd_hda_intel 0000:00:1f.3: azx_get_response timeout, switching to polling mode: last cmd=0x200f0000
<4> [574.170726] snd_hda_intel 0000:00:1f.3: No response from codec, disabling MSI: last cmd=0x200f0000
<4> [575.176727] snd_hda_intel 0000:00:1f.3: Codec #2 probe error; disabling it...
<7> [575.185244] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [575.185669] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x00000067
<6> [575.191360] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC700: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
<6> [575.191385] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [575.191391] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [575.191397] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [575.191402] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [575.191407] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19
<6> [575.971090] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [575.987008] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1f.3/sound/card0/input64
<6> [575.997991] input: HDA Intel PCH Headphone as /devices/pci0000:00/0000:00:1f.3/sound/card0/input65
<7> [576.009769] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [576.010274] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [576.014056] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off
<7> [576.016115] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6
<7> [576.017879] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02
<7> [576.226104] i915 0000:00:02.0: [drm:i915_hdcp_component_unbind [i915]] I915 HDCP comp unbind
<7> [576.294845] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [576.295654] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00
<7> [576.296486] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [576.297260] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [576.298068] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [576.298850] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [576.299703] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [576.300459] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [576.301158] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [576.301928] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [576.302791] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [576.307491] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 1, found 0)
<7> [576.308312] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 1, found 0)
<7> [576.309501] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected 4, found -1)
<7> [576.310150] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 4, found 0)
<7> [576.311239] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 64 data 4209566/8388608 link 350797/524288, found tu 0, data 0/0 link 0/0)
<7> [576.312262] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000100, found 0x00000000)
<7> [576.313245] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 1, found 0)
<7> [576.314188] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 3200, found 0)
<7> [576.314897] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 3316, found 0)
<7> [576.315785] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 3200, found 0)
<7> [576.316703] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 3316, found 0)
<7> [576.317285] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 3248, found 0)
<7> [576.318044] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 3280, found 0)
<7> [576.318661] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 1800, found 0)
<7> [576.319221] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 1816, found 0)
<7> [576.319759] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 1800, found 0)
<7> [576.320293] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 1816, found 0)
<7> [576.320845] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 1802, found 0)
<7> [576.321375] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 1807, found 0)
<7> [576.321879] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 3200, found 0)
<7> [576.322413] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 3316, found 0)
<7> [576.322919] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 3200, found 0)
<7> [576.323443] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 3316, found 0)
<7> [576.323956] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 3248, found 0)
<7> [576.324503] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 3280, found 0)
<6> [576.325083] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [576.325113] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [576.325122] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [576.325132] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [576.325046] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 1800, found 0)
<7> [576.325696] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 1816, found 0)
<7> [576.326209] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 1800, found 0)
<7> [576.326744] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 1816, found 0)
<7> [576.327247] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 1802, found 0)
<7> [576.327837] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 1807, found 0)
<7> [576.328379] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 1, found 0)
<6> [576.328702] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [576.328729] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [576.328738] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [576.328747] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [576.328905] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 2, found 0)
<7> [576.329421] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 8, found 0)
<7> [576.329928] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 24, found 0)
<7> [576.330561] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 361310, found 0)
<7> [576.331064] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 361310, found 0)
<7> [576.331601] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 540000, found 0)
<7> [576.332110] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [576.332645] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll_crtc [i915]] [CRTC:98:pipe A] releasing DPLL 0
<7> [576.333226] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x1 -> 0x0, ddb (0 - 1024) -> (0 - 0), active pipes 0x1 -> 0x0
<7> [576.333787] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 985) -> ( 0 - 0), size 985 -> 0
<7> [576.334165] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 985 - 1024) -> ( 0 - 0), size 39 -> 0
<7> [576.334570] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm
<7> [576.334954] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [576.335326] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [576.335724] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0
<7> [576.336119] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 0 num active planes 0
<7> [576.336559] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 0
<7> [576.336974] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 0
<7> [576.337387] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 0
<7> [576.337853] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [576.338250] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 172800 kHz, actual 172800 kHz
<7> [576.338666] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 0, actual 0
<7> [576.339075] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [modeset]
<7> [576.339511] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no
<7> [576.339938] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
<7> [576.340295] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
<7> [576.340603] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
<7> [576.340900] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
<7> [576.341189] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no
<7> [576.341492] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no
<7> [576.341783] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no
<7> [576.359385] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]
<6> [576.384385] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [576.384404] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [576.384410] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [576.384415] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [576.568762] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 0
<7> [576.570139] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A
<7> [576.589694] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [576.590569] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b
<7> [576.594158] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power off
<7> [576.595131] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power off time
<7> [576.595584] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [576.595940] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060
<7> [576.596329] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [576.597725] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 10
<7> [576.598726] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [576.616385] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [576.616700] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [576.616976] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 20
<7> [576.617296] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [576.648673] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [576.649224] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A
<7> [576.650219] i915 0000:00:02.0: [drm:intel_get_hpd_pins [i915]] hotplug event received, stat 0x00010000, dig 0x0000088a, pins 0x00000010, long 0x00000010
<7> [576.650460] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:98:pipe A]
<7> [576.650717] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] digital hpd on [ENCODER:238:DDI A/PHY A] - long
<7> [576.651100] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0
<7> [576.651190] i915 0000:00:02.0: [drm:intel_hpd_irq_handler [i915]] Received HPD interrupt on PIN 4 - cnt: 30
<7> [576.651622] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [576.652186] i915 0000:00:02.0: [drm:intel_dp_hpd_pulse [i915]] ignoring long hpd on eDP [ENCODER:238:DDI A/PHY A]
<7> [576.652304] i915 0000:00:02.0: [drm:__intel_fbc_disable [i915]] Disabling FBC on [PLANE:31:plane 1A]
<7> [576.653292] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [576.654269] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]
<7> [576.654729] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]
<7> [576.655075] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]
<7> [576.655446] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]
<7> [576.655791] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]
<7> [576.656122] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]
<7> [576.656501] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]
<7> [576.656880] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [576.657259] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [576.657601] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4
<7> [576.658000] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]
<7> [576.694842] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<6> [576.728212] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [576.728240] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [576.728248] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [576.728254] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [576.764435] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [576.765165] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [577.257021] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [577.257883] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<6> [577.910587] PM: suspend entry (deep)
<6> [577.914679] Filesystems sync: 0.004 seconds
<6> [577.916674] Freezing user space processes
<6> [577.919812] Freezing user space processes completed (elapsed 0.003 seconds)
<6> [577.919829] OOM killer disabled.
<6> [577.919835] Freezing remaining freezable tasks
<6> [577.921748] Freezing remaining freezable tasks completed (elapsed 0.001 seconds)
<7> [578.039934] PM: suspend of devices complete after 88.876 msecs
<7> [578.039955] PM: start suspend of devices complete after 117.856 msecs
<7> [578.045663] PM: late suspend of devices complete after 5.697 msecs
<6> [578.050730] ACPI: EC: interrupt blocked
<7> [578.076735] PM: noirq suspend of devices complete after 29.885 msecs
<6> [578.076765] ACPI: PM: Preparing to enter system sleep state S3
<6> [578.085525] ACPI: EC: event blocked
<6> [578.085559] ACPI: EC: EC stopped
<6> [578.085566] ACPI: PM: Saving platform NVS memory
<6> [578.086519] Disabling non-boot CPUs ...
<6> [578.095714] smpboot: CPU 1 is now offline
<6> [578.114096] smpboot: CPU 2 is now offline
<6> [578.130924] smpboot: CPU 3 is now offline
<7> [578.137749] Checking wakeup interrupts
<7> [578.137759] Calling kvm_suspend+0x0/0x90 [kvm]
<7> [578.137852] Calling mce_syscore_suspend+0x0/0x10
<7> [578.137861] Calling timekeeping_suspend+0x0/0x320
<7> [578.138593] Calling save_ioapic_entries+0x0/0xa0
<7> [578.140012] Calling i8259A_suspend+0x0/0x30
<7> [578.140048] Calling iommu_suspend+0x0/0x1b0
<7> [578.140160] Calling fw_suspend+0x0/0x20
<7> [578.140167] Calling acpi_save_bm_rld+0x0/0x20
<7> [578.140193] Calling lapic_suspend+0x0/0x240
<6> [578.140365] ACPI: PM: Low-level resume complete
<6> [578.140439] ACPI: EC: EC started
<6> [578.140444] ACPI: PM: Restoring platform NVS memory
<7> [578.140455] Calling init_counter_refs+0x0/0x70
<7> [578.140468] Calling lapic_resume+0x0/0x340
<7> [578.140614] Calling acpi_restore_bm_rld+0x0/0x70
<7> [578.140625] Calling irqrouter_resume+0x0/0x50
<7> [578.140632] Calling iommu_resume+0x0/0x190
<7> [578.140757] Calling i8259A_resume+0x0/0x30
<7> [578.140993] Calling umwait_syscore_resume+0x0/0x10
<7> [578.140998] Calling ioapic_resume+0x0/0xb0
<7> [578.141299] Calling irq_pm_syscore_resume+0x0/0x10
<7> [578.142305] Calling timekeeping_resume+0x0/0x1c0
<7> [578.142456] Timekeeping suspended for 16.486 seconds
<7> [578.143327] Calling mce_syscore_resume+0x0/0x30
<7> [578.143370] Calling kvm_resume+0x0/0x70 [kvm]
<6> [578.143572] Enabling non-boot CPUs ...
<6> [578.144002] smpboot: Booting Node 0 Processor 1 APIC 0x2
<6> [578.149519] CPU1 is up
<6> [578.149719] smpboot: Booting Node 0 Processor 2 APIC 0x4
<6> [578.154144] CPU2 is up
<6> [578.154338] smpboot: Booting Node 0 Processor 3 APIC 0x6
<6> [578.158046] CPU3 is up
<6> [578.158501] ACPI: PM: Waking up from system sleep state S3
<4> [578.186419] ACPI: button: The lid device is not compliant to SW_LID.
<6> [578.203924] ACPI: EC: interrupt unblocked
<7> [578.221082] PM: noirq resume of devices complete after 18.540 msecs
<7> [578.230778] PM: early resume of devices complete after 7.256 msecs
<6> [578.233259] ACPI: EC: event unblocked
<6> [578.251404] nvme nvme0: 4/0/0 default/read/poll queues
<6> [578.252263] serial 00:03: activated
<6> [578.385088] r8152 1-8:1.0 enx00e04c680775: carrier on
<6> [578.403374] r8169 0000:01:00.0 enp1s0: Link is Down
<7> [578.404328] PM: resume of devices complete after 173.525 msecs
<6> [578.410732] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [578.475581] OOM killer enabled.
<6> [578.475591] Restarting tasks ...
<6> [578.475929] pcieport 0000:00:1c.0: PCI bridge to [bus 01]
<6> [578.475950] pcieport 0000:00:1c.0: bridge window [io 0x3000-0x3fff]
<6> [578.475963] pcieport 0000:00:1c.0: bridge window [mem 0x7fd00000-0x7fdfffff]
<6> [578.476485] pcieport 0000:00:1c.4: PCI bridge to [bus 02]
<6> [578.476499] pcieport 0000:00:1c.4: bridge window [mem 0x7fc00000-0x7fcfffff]
<4> [578.482193] done.
<5> [578.482221] random: crng reseeded on system resumption
<3> [578.484815] atkbd serio0: Failed to deactivate keyboard on isa0060/serio0
<6> [578.498473] PM: suspend exit
<6> [578.510843] [IGT] Re-loading i915
<6> [578.532991] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.533014] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.533020] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.533026] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [578.546116] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.546138] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.546144] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.546149] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [578.549870] ata2: SATA link down (SStatus 4 SControl 300)
<6> [578.556768] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [578.606631] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<6> [578.654916] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.654939] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.654944] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.654950] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [578.667990] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.668012] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.668018] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.668023] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [578.690886] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.690907] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.690913] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.690918] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [578.816378] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [578.816934] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [578.817366] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [578.817794] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [578.818355] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [578.818769] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] rawclk rate: 19200 kHz
<7> [578.820286] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [578.820650] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [578.821726] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [578.822098] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [578.822415] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [578.822710] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [578.822719] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [578.823517] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [578.823554] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [578.823937] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [578.824732] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [578.825186] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [578.825538] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [578.825893] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [578.826241] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [578.835816] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [578.836205] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [578.836537] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [578.836887] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [578.837258] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [578.837574] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [578.837885] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [578.838183] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [578.838467] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [578.838759] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [578.839040] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [578.839325] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [578.839773] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [578.840094] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [578.840378] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [578.840786] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [578.841155] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [578.841506] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [578.841906] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [578.842286] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [578.842638] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [578.843010] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [578.843360] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [578.843711] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [578.844107] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [578.844483] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [578.844848] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [578.845205] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [578.845552] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [578.845911] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [578.846265] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [578.846637] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [578.847030] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [578.847392] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [578.847739] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [578.848645] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [578.849069] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [578.849437] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [578.849815] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [578.850173] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [578.850530] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [578.850930] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [578.851307] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [578.851663] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [578.852040] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [578.852396] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [578.852782] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [578.853167] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [578.853514] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [578.853882] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [578.854228] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [578.854574] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [578.854964] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [578.855348] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [578.855694] i915 0000:00:02.0: [drm:intel_bios_init [i915]] port C trying to use the same DDC pin (0x3) as port A, disabling port A DVI/HDMI support
<7> [578.856133] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [578.856485] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [578.856844] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [578.857185] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 DP++:1 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<6> [578.857425] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.857443] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.857448] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.857453] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [578.857540] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [578.857993] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [578.858350] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 DP++:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [578.858691] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [578.859059] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [578.859404] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [578.859862] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [578.860454] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [578.860918] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 652800 kHz, VCO 1305600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 3
<7> [578.861279] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [578.861951] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [578.862317] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [578.862677] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [578.863177] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [578.863556] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [578.863926] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [578.864297] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [578.864672] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [578.865152] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [578.865510] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [578.865890] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [578.866361] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [578.866948] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<7> [578.868799] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<6> [578.869722] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<3> [578.869865] atkbd serio0: Failed to enable keyboard on isa0060/serio0
<7> [578.869958] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [578.870364] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [578.870724] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [578.871106] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [578.871452] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [578.871858] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [578.872205] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [578.872566] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [578.872979] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [578.888470] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] 3 display pipes available.
<7> [578.896529] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 652800 kHz, VCO 1305600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 3
<7> [578.897102] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind
<6> [578.897494] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])
<7> [578.897862] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [578.898281] i915 0000:00:02.0: [drm:intel_display_driver_probe_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [578.898718] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] using AUX A (VBT)
<7> [578.899119] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [578.903773] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [578.904163] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [578.904515] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [578.905142] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [578.905550] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [578.905943] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [578.906306] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [578.906660] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [578.907021] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [578.907381] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [578.907924] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [578.908367] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 0 t8 0 t9 0 t10 0 t11_t12 0
<7> [578.908709] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [578.909064] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [578.909407] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [578.909780] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [578.910255] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [578.910861] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [578.911453] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [578.911859] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [578.912310] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [578.912670] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [578.913109] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [578.913457] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<6> [578.936596] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [578.936616] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [578.936622] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [578.936627] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [579.118415] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [579.119572] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [579.120954] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [579.122000] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<6> [579.123844] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [579.123863] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [579.123868] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [579.123874] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [579.128669] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.130721] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.132622] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.134577] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.136502] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.138120] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.140117] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.142116] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [579.143498] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [579.143514] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [579.143521] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [579.143621] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [579.144056] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa
<7> [579.144425] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)
<7> [579.156445] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [579.156998] i915 0000:00:02.0: [drm:get_vbt_pwm_freq.isra.0 [i915]] VBT defined backlight frequency 200 Hz
<7> [579.157368] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7> [579.157718] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000
<7> [579.158425] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [579.158812] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [579.159298] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [579.159636] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [579.159983] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [579.160427] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [579.161563] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] using AUX B (VBT)
<7> [579.161979] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [579.162719] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [579.163133] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [579.163490] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [579.164074] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:262:DDI C (TC)/PHY C] using AUX C (platform default)
<7> [579.164425] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [579.164766] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)
<7> [579.165220] i915 0000:00:02.0: [drm:intel_setup_outputs [i915]] VBT says port D is not present
<7> [579.166383] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [579.166884] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [579.167342] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<6> [579.167807] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [579.167826] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [579.167832] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [579.167838] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [579.167712] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [579.168107] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [579.168477] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [579.168843] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [579.169200] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [579.169555] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [579.169925] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [579.170280] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [579.170631] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [579.171027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [579.171402] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [579.171777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [579.172137] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [579.172490] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [579.172854] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [579.173212] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [579.173588] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [579.173989] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [579.174353] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [579.174705] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [579.175071] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [579.175428] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [579.175824] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [579.176196] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [579.176551] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [579.176926] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [579.177268] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [579.177600] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [579.177949] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [579.178301] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [579.178673] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [579.179084] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [579.179462] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [579.179921] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [579.180290] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [579.180645] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [579.181027] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [579.181387] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [579.181757] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [579.182102] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [579.182439] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [579.182788] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [579.183124] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [579.183457] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [579.183833] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [579.184194] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [579.184554] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<7> [579.184921] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [579.185264] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [579.185599] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [579.185946] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [579.186287] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [579.186648] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [579.187028] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [579.187372] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [579.187737] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [579.188098] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [579.188433] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [579.188783] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [579.189138] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [579.189502] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [579.189861] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [579.190209] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [579.190543] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [579.212465] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [579.212898] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [579.213250] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [579.213592] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [579.213959] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [579.214350] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [579.215161] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [579.215479] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [579.215826] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [579.215852] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [579.218650] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0
<7> [579.219076] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [579.219420] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [579.222129] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [579.223590] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [579.224574] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [579.245047] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [579.245455] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [579.245858] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [579.246245] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [579.246672] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [579.248224] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [579.248555] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [579.248893] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [579.249208] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [579.265188] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [579.265971] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [579.267933] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [579.268691] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<7> [579.272844] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [579.273579] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [579.274595] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [579.274696] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [579.278450] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [579.306835] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [579.306858] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [579.306864] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [579.306869] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [579.318463] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [579.327146] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input66
<6> [579.328536] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [579.328929] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x4810 (init value 0x4810)
<7> [579.330171] [drm:drm_client_modeset_probe]
<7> [579.330053] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [579.331077] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [579.331182] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [579.333125] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [579.333523] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [579.334386] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [579.334795] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [579.334803] i915 device info: graphics version: 11
<7> [579.334808] i915 device info: media version: 11
<7> [579.334811] i915 device info: display version: 11
<7> [579.334815] i915 device info: graphics stepping: B0
<7> [579.334819] i915 device info: media stepping: B0
<7> [579.334823] i915 device info: display stepping: B0
<7> [579.334826] i915 device info: base die stepping: **
<7> [579.334829] i915 device info: gt: 0
<7> [579.334833] i915 device info: memory-regions: 0x21
<7> [579.334837] i915 device info: page-sizes: 0x211000
<7> [579.334841] i915 device info: platform: JASPERLAKE
<7> [579.334844] i915 device info: ppgtt-size: 36
<7> [579.334848] i915 device info: ppgtt-type: 2
<7> [579.334851] i915 device info: dma_mask_size: 39
<7> [579.334854] i915 device info: is_mobile: no
<7> [579.334858] i915 device info: is_lp: no
<7> [579.334861] i915 device info: require_force_probe: no
<7> [579.334865] i915 device info: is_dgfx: no
<7> [579.334868] i915 device info: has_64bit_reloc: yes
<7> [579.334872] i915 device info: has_64k_pages: no
<7> [579.334875] i915 device info: gpu_reset_clobbers_display: no
<7> [579.334706] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [579.334879] i915 device info: has_reset_engine: yes
<7> [579.334882] i915 device info: has_3d_pipeline: yes
<7> [579.334885] i915 device info: has_4tile: no
<7> [579.334888] i915 device info: has_flat_ccs: no
<7> [579.334891] i915 device info: has_global_mocs: no
<7> [579.334893] i915 device info: has_gmd_id: no
<7> [579.334896] i915 device info: has_gt_uc: yes
<7> [579.334899] i915 device info: has_heci_pxp: no
<7> [579.334901] i915 device info: has_heci_gscfi: no
<7> [579.334904] i915 device info: has_guc_deprivilege: no
<7> [579.334907] i915 device info: has_l3_ccs_read: no
<7> [579.334910] i915 device info: has_l3_dpf: no
<7> [579.334913] i915 device info: has_llc: yes
<7> [579.334915] i915 device info: has_logical_ring_contexts: yes
<7> [579.334918] i915 device info: has_logical_ring_elsq: yes
<7> [579.334921] i915 device info: has_media_ratio_mode: no
<7> [579.334924] i915 device info: has_mslice_steering: no
<7> [579.334926] i915 device info: has_oa_bpc_reporting: no
<7> [579.334929] i915 device info: has_oa_slice_contrib_limits: no
<7> [579.334932] i915 device info: has_oam: no
<7> [579.334935] i915 device info: has_one_eu_per_fuse_bit: no
<7> [579.334938] i915 device info: has_pxp: no
<7> [579.334940] i915 device info: has_rc6: yes
<7> [579.334943] i915 device info: has_rc6p: no
<7> [579.334946] i915 device info: has_rps: yes
<7> [579.334949] i915 device info: has_runtime_pm: yes
<7> [579.334951] i915 device info: has_snoop: no
<7> [579.334954] i915 device info: has_coherent_ggtt: no
<7> [579.334957] i915 device info: tuning_thread_rr_after_dep: no
<7> [579.334960] i915 device info: unfenced_needs_alignment: no
<7> [579.334962] i915 device info: hws_needs_physical: no
<7> [579.334965] i915 device info: has_pooled_eu: no
<7> [579.334968] i915 device info: cursor_needs_physical: no
<7> [579.334971] i915 device info: has_cdclk_crawl: no
<7> [579.334974] i915 device info: has_cdclk_squash: no
<7> [579.334976] i915 device info: has_ddi: yes
<7> [579.334979] i915 device info: has_dp_mst: yes
<7> [579.334982] i915 device info: has_dsb: no
<7> [579.334985] i915 device info: has_fpga_dbg: yes
<7> [579.334988] i915 device info: has_gmch: no
<7> [579.334990] i915 device info: has_hotplug: yes
<7> [579.334993] i915 device info: has_hti: no
<7> [579.334996] i915 device info: has_ipc: yes
<7> [579.334998] i915 device info: has_overlay: no
<7> [579.335001] i915 device info: has_psr: yes
<7> [579.335004] i915 device info: has_psr_hw_tracking: yes
<7> [579.335007] i915 device info: overlay_needs_physical: no
<7> [579.335010] i915 device info: supports_tv: no
<7> [579.335012] i915 device info: has_hdcp: yes
<7> [579.335015] i915 device info: has_dmc: yes
<7> [579.335018] i915 device info: has_dsc: yes
<7> [579.335020] i915 device info: rawclk rate: 19200 kHz
<7> [579.335024] i915 device info: iommu: enabled
<7> [579.335028] i915 device info: available engines: 40403
<7> [579.335031] i915 device info: slice total: 1, mask=0001
<7> [579.335035] i915 device info: subslice total: 4
<7> [579.335038] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [579.335042] i915 device info: EU total: 16
<7> [579.335045] i915 device info: EU per subslice: 4
<7> [579.335047] i915 device info: has slice power gating: yes
<7> [579.335084] i915 device info: has subslice power gating: yes
<7> [579.335087] i915 device info: has EU power gating: yes
<6> [579.335090] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [579.335093] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [579.335097] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<7> [579.335097] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [579.335846] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [579.335862] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [579.335871] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [579.335956] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [579.336317] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [579.342353] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [579.342779] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [579.343926] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_3
<7> [579.344740] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2
<7> [579.345610] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] status updated from unknown to connected
<7> [579.347240] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :
<7> [579.347288] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [579.347302] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa
<7> [579.347314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [579.347349] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [579.348091] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [579.348142] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [579.348187] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [579.348221] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [579.348658] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [579.348705] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [579.348777] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [579.348812] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [579.349259] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [579.349304] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [579.349343] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [579.349355] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [579.349362] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [579.349369] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [579.349672] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [579.349723] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [579.349732] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [579.349739] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [579.349775] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [579.349800] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<7> [579.350022] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<7> [579.350156] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one
<6> [579.353077] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [579.353094] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [579.353100] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [579.353105] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [579.369002] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [579.377695] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3200x1800 fb: 0x00180000
<6> [579.381085] fbcon: i915drmfb (fb0) is primary device
<6> [579.382213] Console: switching to colour frame buffer device 400x112
<6> [579.382242] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device
<7> [579.391061] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [579.391117] [drm:drm_client_modeset_probe]
<7> [579.391870] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [579.391998] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [579.395035] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [579.395446] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [579.397084] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [579.397479] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [579.399110] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [579.399128] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [579.399137] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [579.401101] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [579.401580] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [579.407948] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [579.408298] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [579.409477] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :
<7> [579.409531] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [579.409545] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa
<7> [579.409556] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [579.409592] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [579.410696] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [579.410739] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [579.410792] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [579.411184] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [579.411220] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [579.411253] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [579.411600] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [579.411634] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [579.411646] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [579.411653] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [579.411660] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [579.412043] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [579.412098] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [579.412106] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [579.412114] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [579.412121] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [579.412185] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<7> [579.414083] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:239:eDP-1] Limiting display bpp to 24 (EDID bpp 24, max requested bpp 36, max platform bpp 36)
<7> [579.414511] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 540000 max bpp 24 pixel clock 361310KHz
<7> [579.414844] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 24
<7> [579.415142] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 1083930 available 2160000
<7> [579.415454] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:239:eDP-1] SDP split enable: no
<7> [579.415786] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] PSR condition failed: PSR setup time (330 us) too long
<7> [579.416086] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:98:pipe A] hw max bpp: 24, pipe bpp: 24, dithering: 0
<7> [579.416394] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:238:DDI A/PHY A] [CRTC:98:pipe A]
<7> [579.416674] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.enable (expected 0, found 1)
<7> [579.417008] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.active (expected 0, found 1)
<7> [579.417317] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in cpu_transcoder (expected -1, found 4)
<7> [579.417618] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in lane_count (expected 0, found 4)
<7> [579.417945] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dp_m_n (expected tu 0 data 0/0 link 0/0, found tu 64, data 4209566/8388608 link 350797/524288)
<7> [579.418251] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in output_types (expected 0x00000000, found 0x00000100)
<7> [579.418550] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in framestart_delay (expected 0, found 1)
<7> [579.418882] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hdisplay (expected 0, found 3200)
<7> [579.419183] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_htotal (expected 0, found 3316)
<7> [579.419485] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_start (expected 0, found 3200)
<7> [579.419810] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hblank_end (expected 0, found 3316)
<7> [579.420114] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_start (expected 0, found 3248)
<7> [579.420426] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_hsync_end (expected 0, found 3280)
<6> [579.421971] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100
<7> [579.422930] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vdisplay (expected 0, found 1800)
<7> [579.423274] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vtotal (expected 0, found 1816)
<7> [579.423577] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_start (expected 0, found 1800)
<7> [579.426781] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vblank_end (expected 0, found 1816)
<7> [579.427563] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_start (expected 0, found 1802)
<7> [579.428192] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_vsync_end (expected 0, found 1807)
<7> [579.428519] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hdisplay (expected 0, found 3200)
<7> [579.429293] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_htotal (expected 0, found 3316)
<7> [579.429609] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_start (expected 0, found 3200)
<7> [579.430237] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hblank_end (expected 0, found 3316)
<7> [579.431157] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_start (expected 0, found 3248)
<7> [579.431506] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_hsync_end (expected 0, found 3280)
<7> [579.432528] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vdisplay (expected 0, found 1800)
<7> [579.433298] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vtotal (expected 0, found 1816)
<7> [579.433607] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_start (expected 0, found 1800)
<7> [579.434535] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vblank_end (expected 0, found 1816)
<6> [579.434803] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [579.435104] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_start (expected 0, found 1802)
<7> [579.435407] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_vsync_end (expected 0, found 1807)
<7> [579.435704] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pixel_multiplier (expected 0, found 1)
<7> [579.436186] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (2) (expected 0, found 2)
<7> [579.436485] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.flags (8) (expected 0, found 8)
<7> [579.436977] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr1 (expected 0x00000000, found 0x0000004b)
<7> [579.437285] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in dpll_hw_state.cfgcr0 (expected 0x00000000, found 0x01c001a5)
<7> [579.437583] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in pipe_bpp (expected 0, found 24)
<7> [579.440907] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.pipe_mode.crtc_clock (expected 0, found 361310)
<7> [579.441265] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in hw.adjusted_mode.crtc_clock (expected 0, found 361310)
<7> [579.441582] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:98:pipe A] fastset requirement not met in port_clock (expected 0, found 540000)
<7> [579.442165] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] fastset requirement not met, forcing full modeset
<7> [579.442570] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:98:pipe A] dbuf slices 0x0 -> 0x1, ddb (0 - 0) -> (0 - 1024), active pipes 0x0 -> 0x1
<7> [579.443116] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 985), size 0 -> 985
<7> [579.443418] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:94:cursor A] ddb ( 0 - 0) -> ( 985 - 1024), size 0 -> 39
<7> [579.443704] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5,*wm6,*wm7,*twm, swm, stwm
<7> [579.444188] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 3, 4, 4, 7, 9, 10, 11, 0, 0, 0
<7> [579.444477] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 26, 79, 105, 105, 183, 235, 261, 287, 40, 0, 0
<7> [579.444998] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 30, 88, 117, 117, 203, 260, 289, 317, 41, 0, 0
<7> [579.445313] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:98:pipe A] data rate 1445240 num active planes 1
<7> [579.445627] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 20069 required 1446
<7> [579.446327] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 23719 required 1446
<7> [579.446632] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 21483 required 1446
<7> [579.447184] i915 0000:00:02.0: [drm:intel_plane_calc_min_cdclk [i915]] [PLANE:31:plane 1A] min cdclk (180655 kHz) > [CRTC:98:pipe A] min cdclk (0 kHz)
<7> [579.447503] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (22582 kHz) > old min cdclk (0 kHz)
<7> [579.448285] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] Modeset required for cdclk change
<7> [579.448597] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New cdclk calculated to be logical 192000 kHz, actual 192000 kHz
<7> [579.449123] i915 0000:00:02.0: [drm:intel_modeset_calc_cdclk [i915]] New voltage level calculated to be logical 1, actual 1
<7> [579.449429] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:98:pipe A] allocated DPLL 0
<7> [579.449720] i915 0000:00:02.0: [drm:intel_reference_shared_dpll_crtc.isra.0 [i915]] [CRTC:98:pipe A] reserving DPLL 0
<7> [579.450240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: yes [modeset]
<7> [579.450542] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB, sink format: RGB
<7> [579.451027] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: EDP, pipe bpp: 24, dithering: 0
<7> [579.451329] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>
<7> [579.451620] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0
<7> [579.452108] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0
<7> [579.452406] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0
<7> [579.452699] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 4209566, data_n: 8388608, link_m: 350797, link_n: 524288, tu: 64
<7> [579.453198] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0
<7> [579.453497] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0
<7> [579.454019] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0
<7> [579.454317] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: -1, vmax vblank: -2
<7> [579.454612] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [579.455151] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [579.455452] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa
<7> [579.455922] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x40 0xa
<7> [579.456223] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=361310, hd=3200 hb=3200-3316 hs=3248-3280 ht=3316, vd=1800 vb=1800-1816 vs=1802-1807 vt=1816, flags=0xa
<7> [579.456515] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3200x1800+0+0, pixel rate 361310
<7> [579.456987] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 74, ips linetime: 0
<7> [579.457283] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0
<7> [579.457576] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no
<7> [579.460780] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0
<7> [579.461132] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c001a5, cfgcr1: 0x4b, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0
<7> [579.461451] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0
<7> [579.462019] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries
<7> [579.462319] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: pre offsets: 0x0000 0x0000 0x0000
<7> [579.462610] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [579.463114] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [579.463422] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: coefficients: 0x0000 0x0000 0x0000
<7> [579.463717] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] output csc: post offsets: 0x0000 0x0000 0x0000
<7> [579.464268] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: pre offsets: 0x0000 0x0000 0x0000
<7> [579.464576] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [579.465147] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [579.465456] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: coefficients: 0x0000 0x0000 0x0000
<7> [579.466026] i915 0000:00:02.0: [drm:ilk_dump_csc [i915]] pipe csc: post offsets: 0x0000 0x0000 0x0000
<7> [579.466330] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:240] 3200x1800 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes
<7> [579.466637] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0
<7> [579.467123] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3200.000000x1800.000000+0.000000+0.000000 dst: 3200x1800+0+0
<7> [579.467421] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no
<7> [579.467712] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no
<7> [579.468186] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no
<7> [579.468479] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no
<7> [579.468927] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:plane 6A] fb: [NOFB], visible: no
<7> [579.469274] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:85:plane 7A] fb: [NOFB], visible: no
<7> [579.469584] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:94:cursor A] fb: [NOFB], visible: no
<6> [579.470977] [IGT] i915_suspend: finished subtest basic-s3-without-i915, SUCCESS
<7> [579.471156] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [579.472005] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Changing CDCLK to 192000 kHz, VCO 384000 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 1
<7> [579.473322] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:238:DDI A/PHY A]
<7> [579.473634] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:247:DDI B/PHY B]
<7> [579.474406] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:249:DP-MST A]
<7> [579.474703] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:250:DP-MST B]
<7> [579.475174] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:251:DP-MST C]
<7> [579.475466] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:262:DDI C (TC)/PHY C]
<7> [579.476002] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<7> [579.476569] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1
<7> [579.477187] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 4
<7> [579.477670] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:98:pipe A]
<7> [579.478266] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0
<7> [579.480179] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turn panel power on
<7> [579.480723] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [579.481383] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [579.481684] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [579.482228] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power on
<7> [579.482600] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x0000006b
<7> [579.692837] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [579.693215] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A
<7> [579.696505] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [579.696578] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using LINK_BW_SET value 14
<7> [579.697545] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0
<7> [579.698046] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS1
<7> [579.699906] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 0/0/0/0
<7> [579.700222] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 0/0/0/0
<7> [579.702203] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Clock recovery OK
<7> [579.702518] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Using DP training pattern TPS3
<7> [579.704377] i915 0000:00:02.0: [drm:intel_dp_get_adjust_train [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing request: 1/1/1/1, pre-emphasis request: 1/1/1/1
<7> [579.704677] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 1/1/1/1, pre-emphasis levels: 1/1/1/1
<7> [579.707144] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful
<7> [579.707448] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:239:eDP-1][ENCODER:238:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4
<7> [579.708234] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A
<7> [579.709114] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]
<7> [579.709412] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A
<7> [579.709905] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:239:eDP-1] set backlight PWM = 96000
<7> [579.713565] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] reserved 23961600 bytes of contiguous stolen space for FBC, limit: 1
<7> [579.713934] i915 0000:00:02.0: [drm:intel_fbc_update [i915]] Enabling FBC on [PLANE:31:plane 1A]
<7> [579.726221] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:239:eDP-1]
<7> [579.726611] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:98:pipe A]
<7> [579.727644] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:238:DDI A/PHY A] Fec status: 0
<7> [579.728009] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp
<7> [579.728359] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0
<6> [579.728684] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [579.728701] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [579.728706] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [579.728711] nvme 0000:02:00.0: [ 0] RxErr (First)
<6> [579.730314] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])
<7> [579.730806] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [579.731319] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [579.731449] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [579.731848] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [579.732436] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x4810
<6> [579.733527] [IGT] i915_suspend: exiting, ret=0
<7> [579.734095] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]
<7> [579.742531] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]
<7> [579.742580] [drm:drm_client_modeset_probe]
<7> [579.743310] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [579.743402] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [579.745541] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:238:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes
<7> [579.745901] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000
<7> [579.746197] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 270000, 540000
<7> [579.746488] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 270000, 540000
<7> [579.747215] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [579.747231] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [579.747239] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [579.747296] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] VRR capable: no
<7> [579.747610] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps
<7> [579.749011] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00
<7> [579.749366] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:239:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no
<7> [579.750943] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] probed modes :
<7> [579.750991] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [579.751004] [drm:drm_mode_debug_printmodeline] Modeline "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa
<7> [579.751015] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [579.751050] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [579.751548] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [579.751585] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [579.751617] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [579.751986] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [579.752023] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [579.752056] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [579.752390] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [579.752423] [drm:drm_client_modeset_probe] connector 239 enabled? yes
<7> [579.752434] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [579.752441] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [579.752448] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [579.752733] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [579.752793] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 239
<7> [579.752803] [drm:drm_client_modeset_probe] looking for preferred mode on connector 239 0
<7> [579.752810] [drm:drm_client_modeset_probe] found mode 3200x1800
<7> [579.752817] [drm:drm_client_modeset_probe] picking CRTCs for 3200x1800 config
<7> [579.752977] [drm:drm_client_modeset_probe] desired mode 3200x1800 set on crtc 98 (0,0)
<6> [579.769529] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC700: line_outs=1 (0x17/0x0/0x0/0x0/0x0) type:speaker
<6> [579.769558] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
<6> [579.769565] snd_hda_codec_realtek hdaudioC0D0: hp_outs=1 (0x21/0x0/0x0/0x0/0x0)
<6> [579.769571] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0
<6> [579.769575] snd_hda_codec_realtek hdaudioC0D0: inputs:
<6> [579.769580] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19
|