Results for igt@i915_selftest@live@sanitycheck

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

DetailValue
Igt-Version 
IGT-Version: 1.27.1-g621c2d311 (x86_64) (Linux: 6.4.0-linus-v6.4-g6995e2de6891+ x86_64)
Out 
Starting subtest: live
Starting dynamic subtest: sanitycheck
Dynamic subtest sanitycheck: SUCCESS (1.801s)
Err 
Starting subtest: live
Starting dynamic subtest: sanitycheck
Dynamic subtest sanitycheck: SUCCESS (1.801s)
Dmesg
<6> [353.378329] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:00:1c.4
<4> [353.378356] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [353.378361] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000
<4> [353.378367] pcieport 0000:00:1c.4: [ 0] RxErr (First)
<6> [353.453523] [IGT] i915_selftest: executing
<6> [353.461430] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:00:1c.4
<4> [353.461454] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [353.461459] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000
<4> [353.461464] pcieport 0000:00:1c.4: [ 0] RxErr (First)
<6> [353.470444] [IGT] i915_selftest: starting subtest live
<6> [353.471241] [IGT] i915_selftest: starting dynamic subtest sanitycheck
<5> [353.631973] Setting dangerous option live_selftests - tainting kernel
<6> [353.669158] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [353.669184] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [353.669189] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [353.669194] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [353.707441] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K
<7> [353.707907] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=0 (guc:no submission:no huc:no slpc:no)
<7> [353.708290] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Jasper Lake PCH
<7> [353.708692] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT
<7> [353.709278] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing
<7> [353.709678] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz
<7> [353.710709] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001
<7> [353.711022] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001
<7> [353.711907] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M
<7> [353.712232] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M
<7> [353.712561] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M
<6> [353.712852] i915 0000:00:02.0: [drm] VT-d active for gfx access
<6> [353.712862] i915 0000:00:02.0: vgaarb: deactivate vga console
<6> [353.713574] i915 0000:00:02.0: [drm] Using Transparent Hugepages
<7> [353.713613] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x000000007fa000c7
<7> [353.713980] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K
<7> [353.714727] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x76f03018
<7> [353.715132] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0
<7> [353.715491] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported
<7> [353.715845] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x
<7> [353.716192] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported
<7> [353.724389] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300583
<7> [353.724781] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported
<7> [353.725106] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported
<7> [353.725762] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)
<7> [353.726132] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4
<7> [353.726673] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [353.726965] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [353.727234] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 2, 16Gb DIMMs: no
<7> [353.727698] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 128 Gb, width: X8, ranks: 2, 16Gb DIMMs: no
<7> [353.727990] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no
<7> [353.728279] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 2, 16Gb DIMMs: no
<7> [353.728767] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes
<7> [353.729149] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2
<7> [353.729453] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no
<7> [353.729737] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2134 tRP=15 tRDPRE=8 tRAS=35 tRCD=15 tRC=50
<7> [353.730114] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=2934 tRP=21 tRDPRE=12 tRAS=47 tRCD=21 tRC=68
<7> [353.730536] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=2401 tRP=17 tRDPRE=9 tRAS=39 tRCD=17 tRC=56
<7> [353.730902] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 0: num_planes=4 deratedbw=9834
<7> [353.731248] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 1: num_planes=4 deratedbw=9941
<7> [353.731605] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW0 / QGV 2: num_planes=4 deratedbw=9878
<7> [353.731947] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 0: num_planes=2 deratedbw=14899
<7> [353.732295] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 1: num_planes=2 deratedbw=16488
<7> [353.732676] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW1 / QGV 2: num_planes=2 deratedbw=15583
<7> [353.733038] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 0: num_planes=1 deratedbw=20069
<7> [353.733454] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 1: num_planes=1 deratedbw=23719
<7> [353.733805] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW2 / QGV 2: num_planes=1 deratedbw=21483
<7> [353.734143] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 0: num_planes=1 deratedbw=24280
<7> [353.734498] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 1: num_planes=1 deratedbw=25000
<7> [353.734850] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW3 / QGV 2: num_planes=1 deratedbw=25000
<7> [353.735215] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 0: num_planes=1 deratedbw=25000
<7> [353.735597] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 1: num_planes=1 deratedbw=25000
<7> [353.735948] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW4 / QGV 2: num_planes=1 deratedbw=25000
<7> [353.736288] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 0: num_planes=1 deratedbw=25000
<7> [353.736634] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 1: num_planes=1 deratedbw=25000
<7> [353.736978] i915 0000:00:02.0: [drm:icl_get_bw_info.constprop.0 [i915]] BW5 / QGV 2: num_planes=1 deratedbw=25000
<7> [353.737972] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz
<7> [353.738384] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT JASPERLAKE ", BDB version 228
<7> [353.738741] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)
<7> [353.739088] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 356, min size 5)
<7> [353.739459] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)
<7> [353.739831] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)
<7> [353.740201] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 780, min size 812)
<7> [353.740569] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 30, min size 34)
<7> [353.740925] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)
<7> [353.741264] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1298, min size 1366)
<7> [353.741617] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)
<7> [353.741975] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 54, min size 78)
<7> [353.742357] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)
<7> [353.742717] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0
<7> [353.743054] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2
<7> [353.743407] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806
<7> [353.743760] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d6
<7> [353.744098] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2
<7> [353.744446] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping
<7> [353.744799] i915 0000:00:02.0: [drm:intel_bios_init [i915]] port C trying to use the same DDC pin (0x3) as port A, disabling port A DVI/HDMI support
<7> [353.745162] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [353.745534] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0
<7> [353.745878] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT DP max link rate: 810000
<7> [353.746213] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [353.746552] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0
<7> [353.746892] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT DP max link rate: 810000
<7> [353.747257] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0
<7> [353.747637] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 0
<7> [353.747983] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT DP max link rate: 810000
<7> [353.748367] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 0a
<7> [353.748736] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [353.749101] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [353.749466] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [353.749816] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [353.750197] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [353.750620] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [353.750974] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [353.751425] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1
<7> [353.751823] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [353.752171] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1
<7> [353.752710] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on
<7> [353.753063] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off
<7> [353.753418] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00
<7> [353.753803] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [353.754159] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.
<7> [353.754512] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [353.754857] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.
<7> [353.755194] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage)
<7> [353.755581] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it.
<7> [353.755945] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2
<7> [353.756290] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_3
<7> [353.756771] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [353.757243] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/icl_dmc_ver1_09.bin
<6> [353.759866] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/icl_dmc_ver1_09.bin (v1.9)
<7> [353.760550] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1
<7> [353.761530] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 10 us
<7> [353.761902] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)
<7> [353.762229] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)
<7> [353.762573] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)
<7> [353.762916] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)
<7> [353.763262] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)
<7> [353.763616] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)
<7> [353.763953] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)
<7> [353.764283] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)
<7> [353.780428] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.
<6> [353.785446] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [353.785470] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [353.785476] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [353.785482] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [353.786445] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 172800 kHz, VCO 345600 kHz, ref 38400 kHz, bypass 50000 kHz, voltage level 0
<7> [353.787007] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 556800 kHz
<7> [353.787411] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1113600 kHz
<7> [353.787822] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:238:DDI A/PHY A] using AUX A (VBT)
<7> [353.788191] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:238:DDI A/PHY A]
<7> [353.793606] i915 0000:00:02.0: [drm:intel_opregion_get_panel_type [i915]] Ignoring OpRegion panel type (0)
<7> [353.793997] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2
<7> [353.794588] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2
<7> [353.794976] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless
<7> [353.795449] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa
<7> [353.795810] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300
<7> [353.796148] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002
<7> [353.796753] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName
<7> [353.797120] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz
<7> [353.797680] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0
<7> [353.798153] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:238:DDI A/PHY A] initial power sequencer: PPS 0
<7> [353.798783] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [353.799138] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [353.799677] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [353.800017] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [353.800564] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [353.801006] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [353.801727] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A
<7> [353.802500] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD on
<7> [353.802866] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<7> [353.803281] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [353.803890] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<7> [353.804490] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000068
<7> [353.804849] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 panel power wasn't enabled
<7> [354.012957] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 12 14 c4 41 00 00 01 c0 02 00 00 00 1f 0b 00
<7> [354.013936] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 00-22-b9 dev-ID sivarT HW-rev 0.0 SW-rev 0.0 quirks 0x0001
<7> [354.014671] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 02 b7 f6
<7> [354.015633] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 1
<7> [354.020684] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.022595] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.024175] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.026105] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.027711] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.029602] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.031530] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.033187] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX A/DDI A/PHY A: native defer
<7> [354.034625] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] Assigning DFP sink color depth as 8 bpc.
<7> [354.034641] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD monitor
<7> [354.034649] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:239:eDP-1] ELD size 20, SAD count 0
<7> [354.034746] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using preferred EDID fixed mode: "3200x1800": 60 361310 3200 3248 3280 3316 1800 1802 1807 1816 0x48 0xa
<7> [354.035156] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:239:eDP-1] using alternate EDID fixed mode: "3200x1800": 52 361310 3200 3248 3280 3424 1800 1802 1807 2045 0x40 0xa
<7> [354.035538] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:239:eDP-1] Performing OUI wait (30 ms)
<7> [354.049987] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:239:eDP-1] DRRS type: none
<7> [354.050529] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:239:eDP-1] Using native PCH PWM for backlight control (controller=0)
<7> [354.050909] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:239:eDP-1] backlight initialized, disabled, brightness 0/96000
<7> [354.051354] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 2000 t8 1 t9 1 t10 500 t11_t12 6000
<7> [354.051896] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000
<7> [354.052249] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100
<7> [354.052602] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600
<7> [354.052940] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200
<7> [354.053384] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60
<7> [354.054465] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:247:DDI B/PHY B] using AUX B (VBT)
<7> [354.054880] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:247:DDI B/PHY B]
<7> [354.055613] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported
<7> [354.055977] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:247:DDI B/PHY B]
<7> [354.056352] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:247:DDI B/PHY B] Using DDC pin 0x2 (VBT)
<7> [354.056922] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:262:DDI C (TC)/PHY C] using AUX C (platform default)
<7> [354.057273] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:262:DDI C (TC)/PHY C]
<7> [354.057619] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:262:DDI C (TC)/PHY C] Using DDC pin 0x3 (VBT)
<7> [354.058047] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present
<7> [354.059204] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:98:pipe A] hw state readout: disabled
<7> [354.059707] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:167:pipe B] hw state readout: disabled
<7> [354.060152] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:236:pipe C] hw state readout: disabled
<7> [354.060539] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A
<7> [354.060909] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A
<7> [354.061269] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A
<7> [354.061638] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A
<7> [354.061990] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A
<7> [354.062354] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] hw state readout: disabled, pipe A
<7> [354.062703] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] hw state readout: disabled, pipe A
<7> [354.063037] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] hw state readout: disabled, pipe A
<7> [354.063436] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] hw state readout: disabled, pipe B
<7> [354.063798] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] hw state readout: disabled, pipe B
<7> [354.064165] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] hw state readout: disabled, pipe B
<7> [354.064547] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] hw state readout: disabled, pipe B
<7> [354.064898] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] hw state readout: disabled, pipe B
<7> [354.065240] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] hw state readout: disabled, pipe B
<7> [354.065595] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] hw state readout: disabled, pipe B
<7> [354.065945] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] hw state readout: disabled, pipe B
<7> [354.066334] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] hw state readout: disabled, pipe C
<7> [354.066699] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] hw state readout: disabled, pipe C
<7> [354.067050] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] hw state readout: disabled, pipe C
<7> [354.067413] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] hw state readout: disabled, pipe C
<7> [354.067758] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] hw state readout: disabled, pipe C
<7> [354.068091] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] hw state readout: disabled, pipe C
<7> [354.068468] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] hw state readout: disabled, pipe C
<7> [354.068842] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] hw state readout: disabled, pipe C
<7> [354.069202] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:238:DDI A/PHY A] hw state readout: disabled, pipe A
<7> [354.069565] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:247:DDI B/PHY B] hw state readout: disabled, pipe A
<7> [354.069902] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:249:DP-MST A] hw state readout: disabled, pipe A
<7> [354.070228] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:250:DP-MST B] hw state readout: disabled, pipe B
<7> [354.070564] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:251:DP-MST C] hw state readout: disabled, pipe C
<7> [354.070911] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:262:DDI C (TC)/PHY C] hw state readout: disabled, pipe A
<7> [354.071280] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 0
<7> [354.071689] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0
<7> [354.072054] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 4 hw state readout: pipe_mask 0x0, on 0
<7> [354.072503] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:239:eDP-1] hw state readout: disabled
<7> [354.072855] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:248:DP-1] hw state readout: disabled
<7> [354.073209] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:257:HDMI-A-1] hw state readout: disabled
<7> [354.073609] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:263:HDMI-A-2] hw state readout: disabled
<7> [354.073964] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz
<7> [354.074292] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz
<7> [354.074636] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz
<7> [354.074960] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz
<7> [354.075281] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz
<7> [354.075681] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:plane 6A] min_cdclk 0 kHz
<7> [354.076038] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:85:plane 7A] min_cdclk 0 kHz
<7> [354.076381] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:94:cursor A] min_cdclk 0 kHz
<7> [354.076715] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0
<7> [354.077058] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 1B] min_cdclk 0 kHz
<7> [354.077397] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 2B] min_cdclk 0 kHz
<7> [354.077732] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 3B] min_cdclk 0 kHz
<7> [354.078078] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:plane 4B] min_cdclk 0 kHz
<7> [354.078442] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:136:plane 5B] min_cdclk 0 kHz
<7> [354.078773] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:145:plane 6B] min_cdclk 0 kHz
<7> [354.079108] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:154:plane 7B] min_cdclk 0 kHz
<7> [354.079455] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:163:cursor B] min_cdclk 0 kHz
<7> [354.079783] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0
<7> [354.080125] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 1C] min_cdclk 0 kHz
<7> [354.080500] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:plane 2C] min_cdclk 0 kHz
<7> [354.080849] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:187:plane 3C] min_cdclk 0 kHz
<7> [354.081189] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:196:plane 4C] min_cdclk 0 kHz
<7> [354.081538] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:205:plane 5C] min_cdclk 0 kHz
<7> [354.081872] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:214:plane 6C] min_cdclk 0 kHz
<7> [354.082185] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:223:plane 7C] min_cdclk 0 kHz
<7> [354.082530] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:232:cursor C] min_cdclk 0 kHz
<7> [354.082875] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0
<7> [354.103162] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:98:pipe A] enable: no [setup_hw_state]
<7> [354.103576] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:167:pipe B] enable: no [setup_hw_state]
<7> [354.103917] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:236:pipe C] enable: no [setup_hw_state]
<7> [354.104259] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:98:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [354.104612] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:167:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [354.104967] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:236:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no
<7> [354.105610] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture
<7> [354.105932] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, 100000000]
<7> [354.106252] MCR Steering: Default steering: group=0x0, instance=0x0
<7> [354.106277] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 9 GT workarounds on global
<7> [354.108870] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 12 engine workarounds on rcs'0
<7> [354.109262] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0
<7> [354.109627] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 context workarounds on rcs'0
<7> [354.112184] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0
<7> [354.113566] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on vcs'0
<7> [354.115100] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0
<7> [354.134249] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:98:pipe A] not active, skipping
<7> [354.134669] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:167:pipe B] not active, skipping
<7> [354.135005] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:236:pipe C] not active, skipping
<7> [354.135353] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config
<7> [354.135766] i915 0000:00:02.0: [drm:i915_gem_open [i915]]
<7> [354.137360] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0
<7> [354.137680] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0
<7> [354.137972] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0
<7> [354.138287] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0
<7> [354.143857] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:239:eDP-1] backlight device intel_backlight registered
<7> [354.144490] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1
<7> [354.146304] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:239:eDP-1] generating connector hotplug event
<7> [354.147084] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX B/DDI B/PHY B bus for card0-DP-1
<6> [354.149989] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:02:00.0
<4> [354.150012] nvme 0000:02:00.0: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [354.150018] nvme 0000:02:00.0: device [15b7:5006] error status/mask=00000001/0000e000
<4> [354.150023] nvme 0000:02:00.0: [ 0] RxErr (First)
<7> [354.150785] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:248:DP-1] generating connector hotplug event
<7> [354.151498] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:257:HDMI-A-1] generating connector hotplug event
<7> [354.152170] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:263:HDMI-A-2] generating connector hotplug event
<6> [354.152266] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0
<7> [354.155856] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected
<6> [354.188075] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)
<6> [354.195349] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input23
<6> [354.198027] sdhci-pci 0000:00:14.5: SDHCI controller found [8086:4df8] (rev 0)
<7> [354.198393] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x810 (init value 0x810)
<7> [354.199478] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_4
<7> [354.200592] [drm:drm_client_modeset_probe]
<7> [354.201157] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1]
<7> [354.201245] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:239:eDP-1]
<7> [354.201702] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] status updated from unknown to disconnected
<7> [354.202659] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:239:eDP-1] disconnected
<7> [354.202697] i915 0000:00:02.0: [drm:drm_edid_connector_update] [CONNECTOR:239:eDP-1] EDID changed, epoch counter 2
<7> [354.202778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1]
<7> [354.202812] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:248:DP-1]
<7> [354.203189] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] status updated from unknown to disconnected
<7> [354.203230] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:248:DP-1] disconnected
<7> [354.203262] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1]
<7> [354.203293] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:257:HDMI-A-1]
<7> [354.203668] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] status updated from unknown to disconnected
<7> [354.203709] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:257:HDMI-A-1] disconnected
<7> [354.203739] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2]
<7> [354.203770] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:263:HDMI-A-2]
<7> [354.204141] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] status updated from unknown to disconnected
<7> [354.204182] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:263:HDMI-A-2] disconnected
<7> [354.204212] [drm:drm_client_modeset_probe] No connectors reported connected with modes
<7> [354.204237] [drm:drm_client_modeset_probe] connector 239 enabled? no
<7> [354.204244] [drm:drm_client_modeset_probe] connector 248 enabled? no
<7> [354.204250] [drm:drm_client_modeset_probe] connector 257 enabled? no
<7> [354.204256] [drm:drm_client_modeset_probe] connector 263 enabled? no
<7> [354.205885] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration
<7> [354.205932] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config
<7> [354.205981] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane
<6> [354.206031] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes
<7> [354.208444] [drm:intel_dsm_detect [i915]] no _DSM method for intel device
<7> [354.208873] i915 device info: pciid=0x4e51 rev=0x01 platform=JASPERLAKE (subplatform=0x0) gen=11
<7> [354.208881] i915 device info: graphics version: 11
<7> [354.208885] i915 device info: media version: 11
<7> [354.208889] i915 device info: display version: 11
<7> [354.208893] i915 device info: graphics stepping: B0
<7> [354.208897] i915 device info: media stepping: B0
<7> [354.208900] i915 device info: display stepping: B0
<7> [354.208903] i915 device info: base die stepping: **
<7> [354.208906] i915 device info: gt: 0
<7> [354.208910] i915 device info: memory-regions: 0x21
<7> [354.208913] i915 device info: page-sizes: 0x211000
<7> [354.208917] i915 device info: platform: JASPERLAKE
<7> [354.208920] i915 device info: ppgtt-size: 36
<7> [354.208924] i915 device info: ppgtt-type: 2
<7> [354.208927] i915 device info: dma_mask_size: 39
<7> [354.208930] i915 device info: is_mobile: no
<7> [354.208934] i915 device info: is_lp: no
<7> [354.208937] i915 device info: require_force_probe: no
<7> [354.208941] i915 device info: is_dgfx: no
<7> [354.208944] i915 device info: has_64bit_reloc: yes
<7> [354.208948] i915 device info: has_64k_pages: no
<7> [354.208951] i915 device info: gpu_reset_clobbers_display: no
<7> [354.208955] i915 device info: has_reset_engine: yes
<7> [354.208958] i915 device info: has_3d_pipeline: yes
<7> [354.208961] i915 device info: has_4tile: no
<7> [354.208965] i915 device info: has_flat_ccs: no
<7> [354.208968] i915 device info: has_global_mocs: no
<7> [354.208971] i915 device info: has_gmd_id: no
<7> [354.208974] i915 device info: has_gt_uc: yes
<7> [354.208978] i915 device info: has_heci_pxp: no
<7> [354.208981] i915 device info: has_heci_gscfi: no
<7> [354.208984] i915 device info: has_guc_deprivilege: no
<7> [354.208988] i915 device info: has_l3_ccs_read: no
<7> [354.208991] i915 device info: has_l3_dpf: no
<7> [354.208994] i915 device info: has_llc: yes
<7> [354.208997] i915 device info: has_logical_ring_contexts: yes
<7> [354.209001] i915 device info: has_logical_ring_elsq: yes
<7> [354.209004] i915 device info: has_media_ratio_mode: no
<7> [354.209007] i915 device info: has_mslice_steering: no
<7> [354.209011] i915 device info: has_oa_bpc_reporting: no
<7> [354.209014] i915 device info: has_oa_slice_contrib_limits: no
<7> [354.209017] i915 device info: has_oam: no
<7> [354.209021] i915 device info: has_one_eu_per_fuse_bit: no
<7> [354.209024] i915 device info: has_pxp: no
<7> [354.209027] i915 device info: has_rc6: yes
<7> [354.209030] i915 device info: has_rc6p: no
<7> [354.209034] i915 device info: has_rps: yes
<7> [354.209037] i915 device info: has_runtime_pm: yes
<7> [354.209040] i915 device info: has_snoop: no
<7> [354.209043] i915 device info: has_coherent_ggtt: no
<7> [354.209047] i915 device info: tuning_thread_rr_after_dep: no
<7> [354.209050] i915 device info: unfenced_needs_alignment: no
<7> [354.209053] i915 device info: hws_needs_physical: no
<7> [354.209056] i915 device info: has_pooled_eu: no
<7> [354.209059] i915 device info: cursor_needs_physical: no
<7> [354.209063] i915 device info: has_cdclk_crawl: no
<7> [354.209066] i915 device info: has_cdclk_squash: no
<7> [354.209069] i915 device info: has_ddi: yes
<7> [354.209072] i915 device info: has_dp_mst: yes
<7> [354.209076] i915 device info: has_dsb: no
<7> [354.209079] i915 device info: has_fpga_dbg: yes
<7> [354.209082] i915 device info: has_gmch: no
<7> [354.209085] i915 device info: has_hotplug: yes
<7> [354.209089] i915 device info: has_hti: no
<7> [354.209092] i915 device info: has_ipc: yes
<7> [354.209095] i915 device info: has_overlay: no
<7> [354.209099] i915 device info: has_psr: yes
<7> [354.209102] i915 device info: has_psr_hw_tracking: yes
<7> [354.209105] i915 device info: overlay_needs_physical: no
<7> [354.209108] i915 device info: supports_tv: no
<7> [354.209112] i915 device info: has_hdcp: no
<7> [354.209115] i915 device info: has_dmc: yes
<7> [354.209118] i915 device info: has_dsc: yes
<7> [354.209121] i915 device info: rawclk rate: 19200 kHz
<7> [354.209126] i915 device info: iommu: enabled
<7> [354.209130] i915 device info: available engines: 40403
<7> [354.209134] i915 device info: slice total: 1, mask=0001
<7> [354.209139] i915 device info: subslice total: 4
<7> [354.209142] i915 device info: slice0: 4 subslices, mask=0000000f
<7> [354.209147] i915 device info: EU total: 16
<7> [354.209150] i915 device info: EU per subslice: 4
<7> [354.209154] i915 device info: has slice power gating: yes
<7> [354.209157] i915 device info: has subslice power gating: yes
<7> [354.209161] i915 device info: has EU power gating: yes
<6> [354.209165] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled
<6> [354.209170] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled
<6> [354.209174] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled
<6> [354.209185] i915: Performing live selftests with st_random_seed=0xd0404b41 st_timeout=500
<6> [354.209190] i915: Running sanitycheck
<6> [354.209193] i915: i915_live_sanitycheck() - ok!
<7> [354.209217] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_4
<7> [354.269811] intel_gt_set_wedged called from intel_gt_set_wedged_on_fini+0xd/0x30 [i915]
<7> [354.318552] i915 0000:00:02.0: [drm:drm_client_release] drm_fb_helper
<7> [354.321182] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 turning VDD off
<7> [354.321758] i915 0000:00:02.0: [drm:intel_pps_vdd_off_sync_unlocked [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [354.323748] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A
<7> [354.326103] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 wait for panel power cycle
<6> [354.376588] pcieport 0000:00:1c.4: AER: Corrected error received: 0000:00:1c.4
<4> [354.376613] pcieport 0000:00:1c.4: PCIe Bus Error: severity=Corrected, type=Physical Layer, (Receiver ID)
<4> [354.376619] pcieport 0000:00:1c.4: device [8086:4dbc] error status/mask=00000001/00002000
<4> [354.376624] pcieport 0000:00:1c.4: [ 0] RxErr (First)
<7> [354.955977] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:238:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060
<7> [354.956991] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete
<4> [354.998231] i915: probe of 0000:00:02.0 failed with error -25
<6> [355.274274] [IGT] i915_selftest: finished subtest sanitycheck, SUCCESS
Created at 2023-06-26 09:03:30