Results for igt@i915_pm_rpm@basic-pci-d3-state

Result: Pass

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g621c2d311 (x86_64) (Linux: 6.4.0-linus-v6.4-g6995e2de6891+ x86_64)
Out	Opened device: /dev/dri/card0 Runtime PM support: 1 PC8 residency support: 0 DMC: fw loaded: yes i915_runtime_pm_status: Runtime power status: enabled GPU idle: yes IRQs disabled: yes Usage count: 0 PCI device power state: D0 [0] Wakeref last acquired: track_intel_runtime_pm_wakeref+0x18/0xc0 [i915] intel_atomic_commit+0x25/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 drm_ioctl_kernel+0xb4/0x150 drm_ioctl+0x21d/0x420 __x64_sys_ioctl+0x76/0xb0 Wakeref last released: __untrack_all_wakerefs+0x6f/0x80 [i915] __intel_wakeref_dec_and_check_tracking+0x4e/0x90 [i915] __intel_runtime_pm_put+0x159/0x2b0 [i915] intel_atomic_commit_tail+0xa2d/0xd10 [i915] intel_atomic_commit+0x380/0x400 [i915] drm_atomic_commit+0x92/0xc0 drm_atomic_helper_set_config+0x77/0xc0 [drm_kms_helper] drm_mode_setcrtc+0x1e9/0x740 Wakeref count: 0 Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (0.562s)
Err	Starting subtest: basic-pci-d3-state Subtest basic-pci-d3-state: SUCCESS (0.562s)
Dmesg	<6> [104.495698] Console: switching to colour dummy device 80x25 <6> [104.495866] [IGT] i915_pm_rpm: executing <7> [104.499371] i915 0000:03:00.0: [drm:i915_gem_open [i915]] <7> [104.500244] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] <7> [104.500261] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [104.500385] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.501304] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.501442] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] disconnected <7> [104.501564] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] <7> [104.501576] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [104.501690] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.502835] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.502962] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] disconnected <7> [104.503132] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] <7> [104.503144] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [104.503259] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.504362] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.504498] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] disconnected <7> [104.504611] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] <7> [104.504622] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [104.504737] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.505878] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.506023] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] disconnected <7> [104.506139] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] <7> [104.506150] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [104.506264] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.507412] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.507552] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] disconnected <7> [104.507668] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] <7> [104.507680] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [104.507792] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.508943] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.509088] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] disconnected <7> [104.509198] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] <7> [104.509210] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [104.509321] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.510474] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.510599] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] disconnected <7> [104.524880] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] <7> [104.524895] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [104.525064] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.525989] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.526159] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] disconnected <7> [104.526867] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] <7> [104.526880] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [104.527026] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.527938] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.528070] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] disconnected <7> [104.528790] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] <7> [104.528802] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [104.528915] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.529849] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.529973] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] disconnected <7> [104.530766] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] <7> [104.530779] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [104.530896] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.531880] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.532013] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] disconnected <7> [104.532724] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] <7> [104.532736] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [104.532850] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.533784] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.533908] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] disconnected <7> [104.534670] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] <7> [104.534682] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [104.534798] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.535720] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.535843] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] disconnected <7> [104.536599] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] <7> [104.536611] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [104.536725] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.537631] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.537757] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] disconnected <7> [104.538786] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] <7> [104.538799] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [104.538914] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.539848] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.539973] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:308:DP-1] disconnected <7> [104.540031] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] <7> [104.540043] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [104.540167] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.541387] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.541511] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] disconnected <7> [104.541538] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] <7> [104.541549] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [104.541660] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.542933] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.543111] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] disconnected <7> [104.543137] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] <7> [104.543149] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [104.543263] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.544431] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.544554] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:331:DP-2] disconnected <7> [104.544584] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] <7> [104.544595] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [104.544706] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.545986] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.546125] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] disconnected <7> [104.546151] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] <7> [104.546162] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [104.546276] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.547506] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.547643] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:343:DP-3] disconnected <7> [104.547670] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] <7> [104.547681] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [104.547793] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [104.549051] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [104.549175] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] disconnected <7> [105.551848] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [105.558878] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [105.566508] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.568140] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.568322] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.568456] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.568589] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.568718] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.568852] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.568988] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.569210] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.569395] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [105.570137] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [105.571388] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [105.571573] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.571751] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [105.571896] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [105.572332] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [105.620108] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [105.620199] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [105.620317] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [105.620472] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [105.620989] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [105.621155] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [105.621281] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [105.621750] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [105.623136] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.623262] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.644696] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [105.649310] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [105.650751] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [105.651070] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.652397] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.652539] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1 <7> [105.652559] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [105.652674] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.653872] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.654006] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6 <7> [105.654021] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [105.654133] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.655349] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.655474] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1 <7> [105.655488] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [105.655603] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.656865] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.657006] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1 <7> [105.657020] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [105.657132] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.658396] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.658523] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1 <7> [105.658537] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [105.658649] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.659914] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.660047] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1 <7> [105.660061] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [105.660176] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.661450] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.661575] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1 <7> [105.663328] [drm:drm_mode_setcrtc] [CRTC:98:pipe A] <7> [105.663471] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.663589] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [105.664512] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.666110] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.666249] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.666384] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.666517] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.666646] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.666780] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.666910] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.667085] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.667212] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [105.667340] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.667455] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.669053] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.669493] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [105.672079] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [105.676644] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.678217] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.678356] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.678490] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.678621] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.678750] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.678884] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.679022] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.679152] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.679340] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [105.679568] [drm:drm_mode_setcrtc] [CRTC:167:pipe B] <7> [105.679746] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [105.681443] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [105.681633] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.681816] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [105.681934] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [105.682144] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [105.706300] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [105.706433] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [105.706553] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [105.706711] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [105.707236] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [105.707376] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [105.707490] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [105.707989] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [105.709374] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.709491] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.729408] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [105.733931] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [105.734046] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.734164] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [105.735459] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.737044] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.737183] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.737318] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.737450] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.737579] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.737714] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.737843] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.737972] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.738104] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [105.738231] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.738346] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.739911] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.740143] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [105.742945] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [105.746068] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.747579] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.747717] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.747852] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.747993] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.748161] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.748294] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.748423] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.748554] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.748743] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [105.749046] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [105.749228] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [105.749388] [drm:drm_mode_setcrtc] [CRTC:236:pipe C] <7> [105.750714] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [105.750904] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.751097] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [105.751216] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [105.751378] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [105.775290] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [105.775374] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [105.775497] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [105.775657] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [105.776197] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [105.776390] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [105.776505] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [105.776935] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [105.778304] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.778422] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.798328] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [105.802891] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [105.802969] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.804398] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.804877] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.805004] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [105.805903] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.807538] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.807676] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.807811] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.807945] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.808124] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.808290] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.808420] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.808549] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.808672] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [105.808799] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.808914] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.810515] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.810677] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1 <7> [105.810861] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [105.811665] [drm:drm_mode_setcrtc] [CRTC:305:pipe D] <7> [105.813547] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [105.818124] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.819681] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.819819] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.819954] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.820092] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.820221] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.820355] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.820484] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.820614] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.820800] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [105.821109] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [105.822747] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [105.822938] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.823139] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [105.823257] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [105.823417] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [105.871297] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [105.871378] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [105.871498] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [105.871658] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [105.872186] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [105.872326] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [105.872440] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [105.872783] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [105.874177] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.874294] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.891153] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [105.892661] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [105.892771] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.892886] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [105.894150] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.895733] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.895872] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.896015] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.896148] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.896278] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.896412] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.896542] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.896671] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.896795] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [105.896923] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.897088] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.898652] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.898783] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [105.901708] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [105.904813] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.906341] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.906495] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.906630] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.906762] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.906891] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.907032] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.907163] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.907292] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.907481] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [105.907708] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [105.908223] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [105.909741] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [105.909933] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.910126] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [105.910248] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [105.910412] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [105.934148] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [105.934222] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [105.934344] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [105.934505] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [105.935048] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [105.935190] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [105.935305] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [105.935611] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [105.936969] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [105.937128] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [105.953998] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [105.957000] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [105.957077] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.958540] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.958672] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6 <7> [105.958688] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [105.958802] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.960063] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.960189] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1 <7> [105.960204] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [105.960319] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.961651] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.961777] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1 <7> [105.961791] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [105.961902] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.963149] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.963275] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1 <7> [105.963288] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [105.963402] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.964631] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.964757] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1 <7> [105.964771] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [105.964885] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.966209] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.966348] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1 <7> [105.966369] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [105.966483] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.967683] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.967809] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1 <7> [105.967823] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [105.967934] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.969214] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.969341] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6 <7> [105.969355] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [105.969466] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.970742] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.970867] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1 <7> [105.970881] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [105.971003] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.972260] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.972385] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1 <7> [105.972399] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [105.972510] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.973793] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.973920] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1 <7> [105.973934] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [105.974057] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.975309] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.975435] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1 <7> [105.975449] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [105.975559] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [105.976844] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [105.976969] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1 <7> [105.977021] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [105.979897] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [105.986036] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [105.987628] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.987766] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [105.987902] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.988059] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [105.988205] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.988339] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [105.988468] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.988597] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [105.988784] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [105.989094] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [105.990733] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [105.990923] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [105.991176] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [105.991308] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [105.991469] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <6> [106.008457] [IGT] i915_pm_rpm: starting subtest basic-pci-d3-state <7> [106.037467] [drm:drm_mode_setcrtc] [CRTC:98:pipe A] <7> [106.049113] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.049225] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.049347] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.049505] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.050076] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.050218] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.050333] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.050624] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.051999] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.052156] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.070492] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.073570] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.073682] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.073797] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.075072] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.076651] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.076789] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.076926] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.077104] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.077234] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.077368] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.077498] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.077628] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.077754] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.077881] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.078027] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.079665] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.079797] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [106.082667] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [106.087297] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.088874] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.089051] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.089187] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.089319] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.089449] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.089583] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.089714] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.089843] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.090082] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [106.090268] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [106.090389] [drm:drm_mode_setcrtc] [CRTC:167:pipe B] <7> [106.090432] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [106.092055] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [106.092246] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.092428] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [106.092546] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [106.092708] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [106.117095] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.117177] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.117298] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.117459] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.117995] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.118137] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.118252] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.118519] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.119877] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.120002] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.136869] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.139872] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.139949] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.141402] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.141667] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.141781] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.142945] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.144498] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.144637] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.144772] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.144904] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.145043] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.145178] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.145308] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.145438] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.145561] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.145689] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.145803] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.147367] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.147532] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1 <7> [106.147557] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [106.148036] [drm:drm_mode_setcrtc] [CRTC:236:pipe C] <7> [106.150438] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [106.155069] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.156562] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.156701] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.156837] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.156970] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.157143] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.157277] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.157406] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.157535] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.157722] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [106.158090] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [106.159742] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [106.159931] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.160161] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [106.160279] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [106.160438] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [106.209093] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.209173] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.209293] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.209449] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.209964] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.210123] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.210238] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.210716] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.212069] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.212184] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.229098] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.232057] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.232217] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.232367] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.233615] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.235171] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.235350] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.235490] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.235627] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.235760] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.235909] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.236079] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.236241] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.236369] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.236498] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.236612] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.238193] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.238372] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [106.242802] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [106.248869] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.250423] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.250561] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.250697] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.250828] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.250958] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.251099] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.251230] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.251361] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.251549] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [106.251742] [drm:drm_mode_setcrtc] [CRTC:305:pipe D] <7> [106.251760] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [106.252023] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [106.253621] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [106.253812] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.254027] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [106.254162] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [106.254324] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [106.278155] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.278231] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.278353] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.278514] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.279057] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.279199] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.279315] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.279579] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.280937] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.281062] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.297930] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.300931] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.301015] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.302503] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.302635] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6 <7> [106.302654] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [106.302768] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.304018] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.304160] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1 <7> [106.304185] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [106.304300] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.305536] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.305677] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1 <7> [106.305692] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [106.305803] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.307086] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.307213] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1 <7> [106.307235] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [106.310085] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [106.313205] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.314713] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.314852] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.314993] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.315125] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.315255] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.315389] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.315518] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.315647] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.315833] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [106.316128] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [106.317686] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [106.317872] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.318098] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [106.318215] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [106.318374] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [106.366067] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.366140] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.366261] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.366423] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.366936] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.367085] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.367200] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.367522] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.368865] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.368990] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.385853] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.388855] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.388967] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.389091] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.390374] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.391958] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.392102] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.392239] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.392370] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.392500] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.392633] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.392764] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.392894] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.393028] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.393156] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.393270] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.394832] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.394962] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [106.397869] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [106.402458] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.404034] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.404173] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.404308] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.404440] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.404569] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.404703] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.404832] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.404962] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.405159] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [106.405361] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [106.405559] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [106.407029] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [106.407229] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.407411] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [106.407529] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [106.407687] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [106.431235] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.431309] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.431430] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.431591] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.432166] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.432307] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.432423] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.432777] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.434144] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.434262] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.451131] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.452637] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.452714] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.454140] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.454270] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1 <7> [106.454285] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [106.454399] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.455670] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.455797] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1 <7> [106.455819] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [106.455933] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.457234] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.457378] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1 <7> [106.457392] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [106.457506] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.458722] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.458849] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6 <7> [106.458863] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [106.458975] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.460277] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.460403] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1 <7> [106.460417] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [106.460532] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.461765] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.461892] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1 <7> [106.461906] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [106.462027] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.463327] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.463453] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1 <7> [106.463468] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [106.463581] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.464835] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.465016] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1 <7> [106.465030] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [106.465143] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.466350] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.466515] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1 <7> [106.466531] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Suspending device <7> [106.469413] i915 0000:03:00.0: [drm:intel_gt_runtime_suspend [i915]] GT0: GUC: communication disabled <7> [106.475507] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.477067] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.477206] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.477340] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.477472] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.477602] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.477736] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.477866] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.478006] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.478226] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x0 <7> [106.478552] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling PW_1 <7> [106.480011] i915 0000:03:00.0: [drm:hsw_wait_for_power_well_disable [i915]] PW_1 forced on (bios:0 driver:0 kvmr:0 debug:0) <7> [106.480198] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.480379] i915 0000:03:00.0: [drm:bxt_enable_dc9 [i915]] Enabling DC9 <7> [106.480496] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 08 <7> [106.480655] i915 0000:03:00.0: [drm:intel_runtime_suspend [i915]] Device suspended <7> [106.529181] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Resuming device <7> [106.529333] i915 0000:03:00.0: [drm:bxt_disable_dc9 [i915]] Disabling DC9 <7> [106.529453] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 08 to 00 <7> [106.529613] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [106.530139] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [106.530332] i915 0000:03:00.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 19200 kHz, VCO 0 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [106.530450] i915 0000:03:00.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [106.530894] i915 0000:03:00.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [106.532242] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.532359] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.552271] i915 0000:03:00.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <7> [106.557064] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:308:DP-1] <7> [106.558324] i915 0000:03:00.0: [drm:intel_runtime_resume [i915]] Device resumed <7> [106.558580] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.559866] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.560038] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:308:DP-1] Same epoch counter 1 <7> [106.560054] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:320:HDMI-A-1] <7> [106.560166] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.561396] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.561523] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:320:HDMI-A-1] Same epoch counter 6 <7> [106.561537] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:327:HDMI-A-2] <7> [106.561649] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.562938] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.563119] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:327:HDMI-A-2] Same epoch counter 1 <7> [106.563133] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:331:DP-2] <7> [106.563248] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.564438] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.564594] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:331:DP-2] Same epoch counter 1 <7> [106.564607] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:339:HDMI-A-3] <7> [106.564719] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.566018] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.566174] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:339:HDMI-A-3] Same epoch counter 1 <7> [106.566188] i915 0000:03:00.0: [drm:intel_dp_detect [i915]] [CONNECTOR:343:DP-3] <7> [106.566300] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.567490] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.567615] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:343:DP-3] Same epoch counter 1 <7> [106.567629] i915 0000:03:00.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:351:HDMI-A-4] <7> [106.567740] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.569047] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.569223] i915 0000:03:00.0: [drm:check_connector_changed [drm_kms_helper]] [CONNECTOR:351:HDMI-A-4] Same epoch counter 1 <7> [106.569252] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <6> [106.570937] [IGT] i915_pm_rpm: finished subtest basic-pci-d3-state, SUCCESS <7> [106.671049] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [106.753741] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.753894] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.754849] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.756448] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.756618] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.756767] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.756898] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.757100] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.757293] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.757422] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.757552] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.757691] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.757833] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.757949] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.759582] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [106.760118] [IGT] i915_pm_rpm: exiting, ret=0 <7> [106.761697] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.761815] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.762852] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.764362] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.764528] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.764663] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.764822] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.764950] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.765137] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.765296] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.765426] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.765566] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.765693] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.765805] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.767412] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on <6> [106.767728] Console: switching to colour frame buffer device 128x48 <7> [106.768663] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [106.768777] i915 0000:03:00.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [106.769678] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 01 to 00 <7> [106.771367] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.771536] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [106.771684] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.771814] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [106.771942] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY C Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.772172] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY C already enabled, won't reprogram it. <7> [106.772315] i915 0000:03:00.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY D Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [106.772445] i915 0000:03:00.0: [drm:icl_combo_phys_init [i915]] Combo PHY D already enabled, won't reprogram it. <7> [106.772583] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [106.772710] i915 0000:03:00.0: [drm:gen9_enable_dc5 [i915]] Enabling DC5 <7> [106.772852] i915 0000:03:00.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 01 <7> [106.774437] i915 0000:03:00.0: [drm:intel_power_well_disable [i915]] disabling always-on

Created at 2023-06-26 09:03:29