igt@i915_module_load@load on bat-adln-1@linus-v6.4 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-g621c2d311 (x86_64) (Linux: 6.4.0-linus-v6.4-g6995e2de6891+ x86_64)
Out	Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (2.151s)
Err	Starting subtest: load Subtest load: SUCCESS (2.151s)
Dmesg	<6> [41.951584] Console: switching to colour dummy device 80x25 <6> [41.951681] [IGT] i915_module_load: executing <6> [41.959619] [IGT] i915_module_load: starting subtest load <4> [42.354558] <4> [42.354571] ******************************************************** <4> [42.354574] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [42.354576] <4> [42.354578] trace_printk() being used. Allocating extra memory. <4> [42.354580] <4> [42.354582] This means that this is a DEBUG kernel and it is <4> [42.354584] unsafe for production use. <4> [42.354586] <4> [42.354588] If you see this message and you are not debugging <4> [42.354590] the kernel, report this immediately to your vendor! <4> [42.354592] <4> [42.354594] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [42.354596] ******************************************************** <7> [42.412787] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K <7> [42.413118] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:yes huc:yes slpc:yes) <7> [42.413426] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Alder Lake PCH <7> [42.413727] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [42.414192] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [42.414463] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz <7> [42.415083] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vcs2 fused off <7> [42.415298] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001 <7> [42.415515] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001 <7> [42.416298] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [42.416547] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [42.416764] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M <6> [42.416966] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [42.423907] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [42.424421] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [42.424596] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x0000000050200087 <7> [42.424907] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K <7> [42.425598] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x44a70018 <7> [42.425940] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0 <7> [42.426209] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [42.426543] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [42.426821] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [42.427120] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (RVDA) <7> [42.427463] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [42.427690] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [42.427907] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2401 tRP=24 tRDPRE=20 tRAS=52 tRCD=24 tRC=76 <7> [42.428214] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=4001 tRP=36 tRDPRE=24 tRAS=84 tRCD=36 tRC=120 <7> [42.428562] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=4401 tRP=40 tRDPRE=28 tRAS=96 tRCD=40 tRC=136 <7> [42.428862] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 3: DCLK=4801 tRP=44 tRDPRE=28 tRAS=104 tRCD=44 tRC=148 <7> [42.429164] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 0: CLK=32 <7> [42.429472] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 1: CLK=38 <7> [42.429754] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 2: CLK=48 <7> [42.430034] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 0: num_planes=0 deratedbw=8478 <7> [42.430308] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 1: num_planes=0 deratedbw=11380 <7> [42.430598] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 2: num_planes=0 deratedbw=11556 <7> [42.430868] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 3: num_planes=0 deratedbw=11991 <7> [42.431140] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 0: num_planes=0 bw=34133 <7> [42.431407] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 1: num_planes=0 bw=40533 <7> [42.431682] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 2: num_planes=0 bw=51200 <7> [42.431952] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 0: num_planes=4 deratedbw=10928 <7> [42.432225] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 1: num_planes=4 deratedbw=15758 <7> [42.432500] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 2: num_planes=4 deratedbw=16388 <7> [42.432764] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 3: num_planes=4 deratedbw=17250 <7> [42.433023] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 0: num_planes=4 bw=34133 <7> [42.433285] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 1: num_planes=4 bw=40533 <7> [42.433558] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 2: num_planes=4 bw=51200 <7> [42.433821] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 0: num_planes=0 deratedbw=12772 <7> [42.434079] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 1: num_planes=0 deratedbw=19510 <7> [42.434338] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 2: num_planes=0 deratedbw=20720 <7> [42.434603] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 3: num_planes=0 deratedbw=22096 <7> [42.434861] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 0: num_planes=0 bw=34133 <7> [42.435118] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 1: num_planes=0 bw=40533 <7> [42.435378] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 2: num_planes=0 bw=51200 <7> [42.435654] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 0: num_planes=0 deratedbw=13950 <7> [42.435915] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 1: num_planes=0 deratedbw=22146 <7> [42.436169] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 2: num_planes=0 deratedbw=23044 <7> [42.436445] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 3: num_planes=0 deratedbw=23044 <7> [42.436726] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 0: num_planes=0 bw=34133 <7> [42.436978] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 1: num_planes=0 bw=40533 <7> [42.437227] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 2: num_planes=0 bw=51200 <7> [42.437520] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 0: num_planes=0 deratedbw=14624 <7> [42.437785] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 1: num_planes=0 deratedbw=23044 <7> [42.438068] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 2: num_planes=0 deratedbw=23044 <7> [42.438320] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 3: num_planes=0 deratedbw=23044 <7> [42.438595] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 0: num_planes=0 bw=34133 <7> [42.438861] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 1: num_planes=0 bw=40533 <7> [42.439121] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 2: num_planes=0 bw=51200 <7> [42.439373] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 0: num_planes=0 deratedbw=14986 <7> [42.439634] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 1: num_planes=0 deratedbw=23044 <7> [42.439888] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 2: num_planes=0 deratedbw=23044 <7> [42.440139] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 3: num_planes=0 deratedbw=23044 <7> [42.440393] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 0: num_planes=0 bw=34133 <7> [42.440653] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 1: num_planes=0 bw=40533 <7> [42.440906] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 2: num_planes=0 bw=51200 <7> [42.441697] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [42.442034] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT ALDERLAKE-P ", BDB version 249 <7> [42.442343] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 6, min size 7) <7> [42.442652] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 395, min size 5) <7> [42.442933] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 100, min size 100) <7> [42.443211] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [42.443529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 812, min size 812) <7> [42.443808] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 34, min size 34) <7> [42.444073] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Generating LFP data table pointers <7> [42.444347] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [42.444638] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1366, min size 1366) <7> [42.444914] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 305, min size 305) <7> [42.445174] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 78, min size 78) <7> [42.445448] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822) <7> [42.445719] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 56 (size 210, min size 210) <7> [42.445980] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0 <7> [42.446233] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [42.446500] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806 <7> [42.446785] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [42.447052] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [42.447314] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [42.447608] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [42.447869] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [42.448128] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0 <7> [42.448380] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [42.448643] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0 <7> [42.448902] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7> [42.449158] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 0 <7> [42.449408] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0 <7> [42.449671] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0 <7> [42.449935] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 4000000a <7> [42.450232] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [42.450602] i915 0000:00:02.0: [drm:check_phy_reg [i915]] Combo PHY A reg 001628a0 state mismatch: current 90035b7c mask e0000000 expected a0000000 <7> [42.450879] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [42.451203] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [42.451497] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [42.451818] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [42.452125] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [42.452401] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf <7> [42.452840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [42.453112] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [42.453379] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [42.453711] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [42.453995] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it. <7> [42.454269] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage) <7> [42.454552] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it. <7> [42.454815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [42.455104] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [42.455150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A <7> [42.455472] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B <7> [42.455758] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C <7> [42.456029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D <7> [42.456411] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/adlp_dmc.bin <7> [42.458951] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [42.460133] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 35 us <7> [42.460477] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 3 (3.0 usec) <7> [42.460816] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 54 (54.0 usec) <7> [42.461157] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 83 (83.0 usec) <7> [42.461509] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 102 (102.0 usec) <7> [42.461840] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 147 (147.0 usec) <7> [42.462165] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 147 (147.0 usec) <6> [42.464719] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adlp_dmc.bin (v2.19) <7> [42.476033] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available. <7> [42.480537] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0 <7> [42.481193] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <6> [42.481868] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <7> [42.482147] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 652800 kHz <7> [42.482486] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1305600 kHz <7> [42.482853] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:184:DDI A/PHY A] using AUX A (VBT) <7> [42.483190] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:184:DDI A/PHY A] <7> [42.483639] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2 <7> [42.483984] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2 <7> [42.484317] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless <7> [42.484664] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa <7> [42.484991] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300 <7> [42.485308] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002 <7> [42.485663] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName <7> [42.485981] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz <7> [42.486295] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0 <7> [42.486702] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:184:DDI A/PHY A] initial power sequencer: PPS 0 <7> [42.487077] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000 <7> [42.487358] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [42.487667] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [42.487959] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [42.488215] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [42.488643] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [42.489026] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [42.489531] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on <7> [42.489907] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f <7> [42.491787] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 00 44 41 00 00 01 c0 02 00 02 00 00 0b 80 <7> [42.492470] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000 <7> [42.492979] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 04 92 a5 <7> [42.493704] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 3 <7> [42.494945] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] PSR2 supported <7> [42.497027] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [42.497298] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] FEC CAPABILITY: 0 <7> [42.508240] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [42.508262] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [42.508269] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [42.508275] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [42.508383] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using preferred EDID fixed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [42.508680] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using alternate EDID fixed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [42.509466] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms) <7> [42.510237] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Detected Intel HDR backlight interface version 1 <7> [42.510503] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Using Intel proprietary eDP backlight controls <7> [42.510758] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:185:eDP-1] DRRS type: seamless <7> [42.511056] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] SDR backlight is controlled through PWM <7> [42.511361] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using native PCH PWM for backlight control (controller=0) <7> [42.511636] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using AUX HDR interface for backlight control (range 0..552) <7> [42.512570] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:185:eDP-1] backlight initialized, enabled, brightness 552/552 <7> [42.512903] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000 <7> [42.513157] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000 <7> [42.513402] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100 <7> [42.513657] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600 <7> [42.513911] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200 <7> [42.514263] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60 <7> [42.514838] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:193:DDI B/PHY B] using AUX B (platform default) <7> [42.515116] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:193:DDI B/PHY B] <7> [42.515361] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:193:DDI B/PHY B] Using DDC pin 0x2 (VBT) <7> [42.515857] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:202:DDI TC1/PHY TC1] using AUX D (VBT) <7> [42.516401] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port D/TC#1: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected) <7> [42.516770] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:202:DDI TC1/PHY TC1] <7> [42.517349] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:211:DDI TC2/PHY TC2] using AUX E (VBT) <7> [42.517669] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port E/TC#2: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected) <7> [42.517999] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:211:DDI TC2/PHY TC2] <7> [42.518508] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port F is not present <7> [42.518790] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port G is not present <7> [42.519569] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled <7> [42.520003] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:131:pipe B] hw state readout: disabled <7> [42.520425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:182:pipe C] hw state readout: disabled <7> [42.520724] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: enabled, pipe A <7> [42.521016] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A <7> [42.521297] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A <7> [42.521594] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A <7> [42.521874] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A <7> [42.522150] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] hw state readout: disabled, pipe A <7> [42.522445] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] hw state readout: disabled, pipe B <7> [42.522726] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] hw state readout: disabled, pipe B <7> [42.522993] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] hw state readout: disabled, pipe B <7> [42.523267] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] hw state readout: disabled, pipe B <7> [42.523563] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] hw state readout: disabled, pipe B <7> [42.523838] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] hw state readout: disabled, pipe B <7> [42.524105] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] hw state readout: disabled, pipe C <7> [42.524377] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] hw state readout: disabled, pipe C <7> [42.524674] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] hw state readout: disabled, pipe C <7> [42.524945] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] hw state readout: disabled, pipe C <7> [42.525213] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] hw state readout: disabled, pipe C <7> [42.525504] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] hw state readout: disabled, pipe C <7> [42.525847] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0 <7> [42.526117] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp <7> [42.526497] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:184:DDI A/PHY A] hw state readout: enabled, pipe A <7> [42.526786] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:193:DDI B/PHY B] hw state readout: disabled, pipe A <7> [42.527102] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port D/TC#1: sanitize mode (disconnected) <7> [42.527371] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:202:DDI TC1/PHY TC1] hw state readout: disabled, pipe A <7> [42.527658] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:204:DP-MST A] hw state readout: disabled, pipe A <7> [42.527924] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:205:DP-MST B] hw state readout: disabled, pipe B <7> [42.528177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:206:DP-MST C] hw state readout: disabled, pipe C <7> [42.528474] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port E/TC#2: sanitize mode (disconnected) <7> [42.528736] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:211:DDI TC2/PHY TC2] hw state readout: disabled, pipe A <7> [42.528996] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:213:DP-MST A] hw state readout: disabled, pipe A <7> [42.529259] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:214:DP-MST B] hw state readout: disabled, pipe B <7> [42.529572] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:215:DP-MST C] hw state readout: disabled, pipe C <7> [42.529856] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1 <7> [42.530142] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [42.530428] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TBT PLL hw state readout: pipe_mask 0x0, on 0 <7> [42.530744] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [42.531032] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [42.531306] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [42.531608] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0 <7> [42.532046] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:185:eDP-1] hw state readout: enabled <7> [42.532351] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:194:HDMI-A-1] hw state readout: disabled <7> [42.532664] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:203:DP-1] hw state readout: disabled <7> [42.532952] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:212:DP-2] hw state readout: disabled <7> [42.533368] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 269300 kHz <7> [42.533659] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz <7> [42.533937] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz <7> [42.534185] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz <7> [42.534447] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz <7> [42.534705] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] min_cdclk 0 kHz <7> [42.534962] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 2154400 num active planes 1 <7> [42.535266] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] min_cdclk 0 kHz <7> [42.535545] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] min_cdclk 0 kHz <7> [42.535802] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] min_cdclk 0 kHz <7> [42.536056] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] min_cdclk 0 kHz <7> [42.536308] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] min_cdclk 0 kHz <7> [42.536576] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] min_cdclk 0 kHz <7> [42.536827] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [42.537121] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] min_cdclk 0 kHz <7> [42.537381] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] min_cdclk 0 kHz <7> [42.537648] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] min_cdclk 0 kHz <7> [42.537898] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] min_cdclk 0 kHz <7> [42.538152] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] min_cdclk 0 kHz <7> [42.538399] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] min_cdclk 0 kHz <7> [42.538658] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [42.538965] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [42.539499] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [setup_hw_state] <7> [42.539805] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB <7> [42.540093] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0 <7> [42.540377] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [42.540675] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [42.540959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [42.541240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [42.541534] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 653660, link_n: 524288, tu: 64 <7> [42.541814] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [42.542092] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [42.542371] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0 <7> [42.542660] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0 <7> [42.542942] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [42.543219] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [42.543520] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [42.543800] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [42.544071] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [42.544346] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 432000, pipe src: 3840x2160+0+0, pixel rate 538600 <7> [42.544641] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0 <7> [42.544919] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [42.545186] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [42.545470] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [42.545747] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c2, cfgcr1: 0x84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [42.546027] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0 <7> [42.546300] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [42.546588] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:131:pipe B] enable: no [setup_hw_state] <7> [42.546878] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:182:pipe C] enable: no [setup_hw_state] <7> [42.547292] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:80:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no <7> [42.547587] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:131:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [42.547863] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:182:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no <7> [42.548523] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] pipe A/plane 1A with fb: size=3840x2160@32, offset=0, pitch 15360, size 0x1fa4000 <7> [42.548800] i915 0000:00:02.0: [drm:intel_plane_disable_noatomic [i915]] Disabling [PLANE:31:plane 1A] on [CRTC:80:pipe A] <7> [42.574833] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [592K, 1420K) <7> [42.575170] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [42.575449] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000] <7> [42.575712] MCR Steering: Default steering: group=0x0, instance=0x0 <7> [42.575731] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 3 GT workarounds on global <7> [42.577376] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0 <7> [42.577683] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0 <7> [42.577959] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 context workarounds on rcs'0 <7> [42.579882] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0 <7> [42.580166] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0 <7> [42.580450] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on bcs'0 <7> [42.581196] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0 <7> [42.581479] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'0 <7> [42.582177] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0 <7> [42.582458] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0 <7> [42.585282] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3) <7> [42.585708] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset <7> [42.624045] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0x16304f <7> [42.624416] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x44000 <7> [42.625113] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4 <7> [42.625455] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3 <7> [42.625755] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0xac8 <7> [42.626043] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x46d00000 <7> [42.626336] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0 <7> [42.626638] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0 <7> [42.626929] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0 <7> [42.627209] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0 <7> [42.627534] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0 <7> [42.627822] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0 <7> [42.628101] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0 <7> [42.628382] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0 <7> [42.628674] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no <6> [42.630208] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/tgl_guc_70.bin version 70.5.1 <6> [42.630215] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3 <7> [42.633453] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 1ms, freq = 750MHz, before = 750MHz, status = 0x8002F0EC, count = 0, ret = 0 <7> [42.634824] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <6> [42.636448] i915 0000:00:02.0: [drm] GT0: HuC: authenticated! <6> [42.637544] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled <6> [42.637550] i915 0000:00:02.0: [drm] GT0: GUC: SLPC enabled <6> [42.638449] i915 0000:00:02.0: [drm] GT0: GUC: RC enabled <7> [42.647704] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [42.648323] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [42.648750] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz <7> [42.649110] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30 <7> [42.649479] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000 <7> [42.649835] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no <7> [42.650179] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [42.650574] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A] <7> [42.650923] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048) <7> [42.651287] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5) <7> [42.651674] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 24, found 30) <7> [42.652045] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 432000, found 540000) <7> [42.652398] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] releasing DPLL 0 <7> [42.652810] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7> [42.653163] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7> [42.653627] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [42.654045] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state <7> [42.654471] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [42.654848] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz <7> [42.655177] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30 <7> [42.655510] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000 <7> [42.655850] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no <7> [42.656176] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [42.656543] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A] <7> [42.656873] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048) <7> [42.657227] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5) <7> [42.657593] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 24, found 30) <7> [42.657940] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 432000, found 540000) <7> [42.658286] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] releasing DPLL 0 <7> [42.658675] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes <7> [42.659011] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1 <7> [42.659423] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2048) -> ( 0 - 0), size 2048 -> 0 <7> [42.659782] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69 <7> [42.660108] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm,swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [42.660425] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 6, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.660768] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 32, 32, 7, 7, 7, 7, 0, 0, 7, 187, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.661098] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.661445] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [42.661786] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.662101] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.662420] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.662763] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [42.663084] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.663393] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.663741] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.664061] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [42.664370] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.664699] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.665017] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.665330] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [42.665661] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.665975] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.666286] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.666615] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm <7> [42.666935] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.667242] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.667563] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 <7> [42.667920] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0 <7> [42.668262] i915 0000:00:02.0: [drm:intel_reference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0 <6> [42.668618] i915 0000:00:02.0: [drm] Selective fetch area calculation failed in pipe A <7> [42.668626] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset] <7> [42.668973] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB <7> [42.669313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [42.669666] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [42.669999] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [42.670330] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [42.670678] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [42.671013] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64 <7> [42.671337] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [42.671686] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [42.672021] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [42.672343] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0 <7> [42.672349] i915 0000:00:02.0: pixelformat: RGB <7> [42.672353] i915 0000:00:02.0: colorimetry: sRGB <7> [42.672357] i915 0000:00:02.0: bpc: 0 <7> [42.672360] i915 0000:00:02.0: dynamic range: VESA range <7> [42.672365] i915 0000:00:02.0: content type: Not defined <7> [42.672369] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0 <7> [42.672714] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [42.673049] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [42.673381] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [42.673731] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [42.674062] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [42.674384] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600 <7> [42.674735] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0 <7> [42.675064] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [42.675380] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [42.675718] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [42.676049] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [42.676381] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [42.676713] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [42.677042] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no <7> [42.677366] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [42.677936] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [42.678288] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [42.678989] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [42.679338] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [42.681766] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]] <7> [42.887547] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 0 <7> [42.888407] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A <7> [42.897094] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power off <7> [42.897469] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power off time <7> [42.897899] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060 <7> [42.951335] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [42.951679] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A <7> [42.952217] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A] <7> [42.952607] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0 <7> [42.952912] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A <7> [42.953220] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A] <7> [42.953528] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B] <7> [42.953812] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1] <7> [42.954086] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A] <7> [42.954354] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B] <7> [42.954634] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C] <7> [42.954905] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2] <7> [42.955169] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A] <7> [42.955451] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B] <7> [42.955714] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C] <7> [42.955970] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [42.956259] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [42.956558] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL <7> [42.956837] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1 <7> [42.957108] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2 <7> [42.957380] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3 <7> [42.957669] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4 <7> [42.957962] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf <7> [42.958332] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A <7> [42.958631] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A] <7> [42.958906] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0 <7> [42.959319] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power on <7> [42.959633] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power cycle <7> [43.599876] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060 <7> [43.600375] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [43.600888] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power on <7> [43.601374] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063 <7> [43.813965] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete <7> [43.814870] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A <7> [43.816144] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on <7> [43.816990] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b <7> [43.819991] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80 <7> [43.820066] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:185:eDP-1] Reloading eDP link rates <7> [43.820992] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [ENCODER:184:DDI A/PHY A] Using LINK_RATE_SET value 06 <7> [43.821852] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:184:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0 <7> [43.822086] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS1 <7> [43.823288] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Clock recovery OK <7> [43.823447] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS3 <7> [43.824911] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful <7> [43.825094] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4 <7> [43.825632] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A <7> [43.825992] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]] <7> [43.826154] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A <7> [43.826313] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms) <7> [43.827120] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000 <7> [43.842777] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf <7> [43.843346] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1] <7> [43.843730] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [43.844999] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0 <7> [43.845454] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp <7> [43.845968] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [43.846865] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [PLANE:31:plane 1A] no fb, skipping <7> [43.847277] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:131:pipe B] not active, skipping <7> [43.847669] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:182:pipe C] not active, skipping <7> [43.848034] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [43.848462] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [43.849901] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [43.850256] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [43.850601] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [43.850847] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [43.863675] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:185:eDP-1] backlight device intel_backlight registered <7> [43.864384] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1 <7> [43.867110] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:185:eDP-1] generating connector hotplug event <7> [43.867958] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:194:HDMI-A-1] generating connector hotplug event <7> [43.868901] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1 <7> [43.870658] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:203:DP-1] generating connector hotplug event <7> [43.871560] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2 <7> [43.873553] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:212:DP-2] generating connector hotplug event <6> [43.873674] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [43.879207] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected <6> [43.898611] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [43.903025] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3 <7> [43.905531] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010) <7> [43.905776] i915 0000:00:02.0: [drm:intel_audio_init [i915]] aud_ts_cdclk set to M=60, N=768 <7> [43.906481] [drm:drm_client_modeset_probe] <7> [43.906427] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_D <7> [43.906720] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] <7> [43.906759] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1] <7> [43.908958] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [43.909176] i915 device info: pciid=0x46d0 rev=0x00 platform=ALDERLAKE_P (subplatform=0x2) gen=12 <7> [43.909180] i915 device info: graphics version: 12 <7> [43.909182] i915 device info: media version: 12 <7> [43.909184] i915 device info: display version: 13 <7> [43.909186] i915 device info: graphics stepping: A0 <7> [43.909187] i915 device info: media stepping: A0 <7> [43.909189] i915 device info: display stepping: D0 <7> [43.909191] i915 device info: base die stepping: ** <7> [43.909192] i915 device info: gt: 0 <7> [43.909194] i915 device info: memory-regions: 0x21 <7> [43.909195] i915 device info: page-sizes: 0x211000 <7> [43.909197] i915 device info: platform: ALDERLAKE_P <7> [43.909198] i915 device info: ppgtt-size: 48 <7> [43.909200] i915 device info: ppgtt-type: 2 <7> [43.909201] i915 device info: dma_mask_size: 39 <7> [43.909203] i915 device info: is_mobile: no <7> [43.909205] i915 device info: is_lp: no <7> [43.909206] i915 device info: require_force_probe: no <7> [43.909208] i915 device info: is_dgfx: no <7> [43.909209] i915 device info: has_64bit_reloc: yes <7> [43.909211] i915 device info: has_64k_pages: no <7> [43.909212] i915 device info: gpu_reset_clobbers_display: no <7> [43.909214] i915 device info: has_reset_engine: yes <7> [43.909215] i915 device info: has_3d_pipeline: yes <7> [43.909217] i915 device info: has_4tile: no <7> [43.909218] i915 device info: has_flat_ccs: no <7> [43.909220] i915 device info: has_global_mocs: yes <7> [43.909221] i915 device info: has_gmd_id: no <7> [43.909223] i915 device info: has_gt_uc: yes <7> [43.909224] i915 device info: has_heci_pxp: no <7> [43.909226] i915 device info: has_heci_gscfi: no <7> [43.909227] i915 device info: has_guc_deprivilege: no <7> [43.909229] i915 device info: has_l3_ccs_read: no <7> [43.909230] i915 device info: has_l3_dpf: no <7> [43.909232] i915 device info: has_llc: yes <7> [43.909233] i915 device info: has_logical_ring_contexts: yes <7> [43.909235] i915 device info: has_logical_ring_elsq: yes <7> [43.909236] i915 device info: has_media_ratio_mode: no <7> [43.909238] i915 device info: has_mslice_steering: no <7> [43.909239] i915 device info: has_oa_bpc_reporting: no <7> [43.909241] i915 device info: has_oa_slice_contrib_limits: no <7> [43.909242] i915 device info: has_oam: no <7> [43.909244] i915 device info: has_one_eu_per_fuse_bit: no <7> [43.909245] i915 device info: has_pxp: yes <7> [43.909247] i915 device info: has_rc6: yes <7> [43.909248] i915 device info: has_rc6p: no <7> [43.909250] i915 device info: has_rps: yes <7> [43.909251] i915 device info: has_runtime_pm: yes <7> [43.909253] i915 device info: has_snoop: no <7> [43.909254] i915 device info: has_coherent_ggtt: no <7> [43.909255] i915 device info: tuning_thread_rr_after_dep: no <7> [43.909257] i915 device info: unfenced_needs_alignment: no <7> [43.909258] i915 device info: hws_needs_physical: no <7> [43.909260] i915 device info: has_pooled_eu: no <7> [43.909261] i915 device info: cursor_needs_physical: no <7> [43.909263] i915 device info: has_cdclk_crawl: yes <7> [43.909264] i915 device info: has_cdclk_squash: no <7> [43.909266] i915 device info: has_ddi: yes <7> [43.909267] i915 device info: has_dp_mst: yes <7> [43.909269] i915 device info: has_dsb: yes <7> [43.909270] i915 device info: has_fpga_dbg: yes <7> [43.909271] i915 device info: has_gmch: no <7> [43.909273] i915 device info: has_hotplug: yes <7> [43.909274] i915 device info: has_hti: no <7> [43.909276] i915 device info: has_ipc: yes <7> [43.909277] i915 device info: has_overlay: no <7> [43.909279] i915 device info: has_psr: yes <7> [43.909280] i915 device info: has_psr_hw_tracking: no <7> [43.909282] i915 device info: overlay_needs_physical: no <7> [43.909283] i915 device info: supports_tv: no <7> [43.909284] i915 device info: has_hdcp: yes <7> [43.909286] i915 device info: has_dmc: yes <7> [43.909287] i915 device info: has_dsc: yes <7> [43.909289] i915 device info: rawclk rate: 19200 kHz <7> [43.909291] i915 device info: iommu: enabled <7> [43.909293] i915 device info: available engines: 40403 <7> [43.909295] i915 device info: slice total: 1, mask=0001 <7> [43.909297] i915 device info: subslice total: 2 <7> [43.909298] i915 device info: slice0: 2 subslices, mask=00000003 <7> [43.909300] i915 device info: EU total: 32 <7> [43.909302] i915 device info: EU per subslice: 16 <7> [43.909303] i915 device info: has slice power gating: yes <7> [43.909305] i915 device info: has subslice power gating: no <7> [43.909306] i915 device info: has EU power gating: no <6> [43.909308] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [43.909310] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [43.909312] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [43.909470] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [43.909660] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [43.910319] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [43.910513] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [43.910688] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [43.910863] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000 <7> [43.911142] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [43.911152] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [43.911157] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [43.911161] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [43.911197] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no <7> [43.911372] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [43.912160] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [43.912358] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [43.913666] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_B <7> [43.914018] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_C <7> [43.914247] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [43.914550] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] status updated from unknown to connected <7> [43.915314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] probed modes : <7> [43.915336] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [43.915344] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [43.915350] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] <7> [43.915367] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1] <7> [43.915703] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] status updated from unknown to disconnected <7> [43.915726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] disconnected <7> [43.915749] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] <7> [43.915763] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1] <7> [43.916049] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] status updated from unknown to disconnected <7> [43.916071] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] disconnected <7> [43.916090] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] <7> [43.916105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2] <7> [43.916937] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] status updated from unknown to disconnected <7> [43.916962] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] disconnected <7> [43.916981] [drm:drm_client_modeset_probe] connector 185 enabled? yes <7> [43.916987] [drm:drm_client_modeset_probe] connector 194 enabled? no <7> [43.916990] [drm:drm_client_modeset_probe] connector 203 enabled? no <7> [43.916992] [drm:drm_client_modeset_probe] connector 212 enabled? no <7> [43.917118] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [43.917142] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185 <7> [43.917146] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0 <7> [43.917149] [drm:drm_client_modeset_probe] found mode 3840x2160 <7> [43.917151] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [43.917162] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0) <7> [43.917222] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <7> [43.917283] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one <7> [43.934226] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3840x2160 fb: 0x00e80000 <6> [43.936512] fbcon: i915drmfb (fb0) is primary device <7> [43.939332] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36) <7> [43.939773] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz <7> [43.939958] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30 <7> [43.940134] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000 <7> [43.940310] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no <7> [43.940943] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0 <7> [43.941160] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A] <7> [43.941424] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027 <7> [43.941888] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0,wm1,wm2,wm3,wm4,wm5, wm6, wm7,twm,swm,*stwm <7> [43.942085] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0 <7> [43.942260] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201 <7> [43.942844] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207 <7> [43.943036] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 2154400 num active planes 1 <7> [43.943225] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263 <7> [43.943407] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263 <7> [43.943682] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263 <7> [43.943872] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263 <7> [43.944063] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263 <7> [43.944246] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263 <7> [43.944427] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263 <7> [43.944684] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (42079 kHz) > old min cdclk (0 kHz) <7> [43.944883] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [fastset] <7> [43.945072] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB <7> [43.945255] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0 <7> [43.945486] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid> <7> [43.945674] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0 <7> [43.945859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0 <7> [43.946043] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0 <7> [43.946230] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64 <7> [43.946417] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0 <7> [43.946648] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0 <7> [43.946834] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4 <7> [43.947018] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0 <7> [43.947021] i915 0000:00:02.0: pixelformat: RGB <7> [43.947023] i915 0000:00:02.0: colorimetry: sRGB <7> [43.947025] i915 0000:00:02.0: bpc: 0 <7> [43.947027] i915 0000:00:02.0: dynamic range: VESA range <7> [43.947028] i915 0000:00:02.0: content type: Not defined <7> [43.947031] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0 <7> [43.947207] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [43.947393] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [43.947625] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [43.947808] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [43.947991] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa <7> [43.948169] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600 <7> [43.948343] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0 <7> [43.948562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0 <7> [43.948734] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no <7> [43.948906] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0 <7> [43.949086] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0 <7> [43.949267] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0 <7> [43.949480] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries <7> [43.949657] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:186] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes <7> [43.949834] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0 <7> [43.950003] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0 <7> [43.950174] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no <7> [43.950345] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no <7> [43.950557] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no <7> [43.950729] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no <7> [43.950897] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no <7> [43.951648] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A] <7> [43.951836] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B] <7> [43.952006] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1] <7> [43.952173] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A] <7> [43.952338] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B] <7> [43.952564] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C] <7> [43.952736] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2] <7> [43.952902] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A] <7> [43.953068] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B] <7> [43.953233] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C] <7> [43.953403] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [43.953814] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1 <7> [43.954007] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL <7> [43.954185] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1 <7> [43.954363] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2 <7> [43.954652] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3 <7> [43.954837] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4 <7> [43.959247] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2 <7> [43.960892] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1] <7> [43.961128] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A] <7> [43.961695] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0 <7> [43.961909] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0 <7> [43.962492] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=552/552 <7> [43.962679] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:185:eDP-1] set backlight level = 552 <7> [43.962856] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000 <6> [43.964111] Console: switching to colour frame buffer device 480x135 <6> [43.984055] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device <7> [43.997556] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]] <7> [43.997582] [drm:drm_client_modeset_probe] <7> [43.997749] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] <7> [43.997781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1] <7> [43.998837] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [43.998991] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [43.999624] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [43.999767] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [43.999902] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [44.000034] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000 <7> [44.000278] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [44.000286] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [44.000290] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [44.000293] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [44.000319] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no <7> [44.000466] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [44.001223] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [44.001359] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [44.002225] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] probed modes : <7> [44.002250] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [44.002256] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [44.002260] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] <7> [44.002275] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1] <7> [44.002504] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] disconnected <7> [44.002521] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] <7> [44.002534] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1] <7> [44.002763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] disconnected <7> [44.002778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] <7> [44.002791] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2] <7> [44.002966] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] disconnected <7> [44.002979] [drm:drm_client_modeset_probe] connector 185 enabled? yes <7> [44.002983] [drm:drm_client_modeset_probe] connector 194 enabled? no <7> [44.002985] [drm:drm_client_modeset_probe] connector 203 enabled? no <7> [44.002987] [drm:drm_client_modeset_probe] connector 212 enabled? no <7> [44.003064] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [44.003080] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185 <7> [44.003082] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0 <7> [44.003084] [drm:drm_client_modeset_probe] found mode 3840x2160 <7> [44.003086] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config <7> [44.003116] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0) <7> [44.009849] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]] <7> [44.009870] [drm:drm_client_modeset_probe] <7> [44.009905] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] <7> [44.009924] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1] <7> [44.010828] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [44.010990] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0 <7> [44.011593] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes <7> [44.011750] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000 <7> [44.011905] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000 <7> [44.012049] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000 <7> [44.012219] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz <7> [44.012228] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc. <7> [44.012233] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor <7> [44.012238] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0 <7> [44.012259] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no <7> [44.012404] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps <7> [44.013252] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 <7> [44.013404] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no <7> [44.014157] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] probed modes : <7> [44.014178] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa <7> [44.014185] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa <7> [44.014191] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] <7> [44.014209] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1] <7> [44.014392] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] disconnected <7> [44.014410] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] <7> [44.014426] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1] <7> [44.014761] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] disconnected <7> [44.014777] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] <7> [44.014793] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2] <7> [44.014973] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] disconnected <7> [44.014988] [drm:drm_client_modeset_probe] connector 185 enabled? yes <7> [44.014993] [drm:drm_client_modeset_probe] connector 194 enabled? no <7> [44.014996] [drm:drm_client_modeset_probe] connector 203 enabled? no <7> [44.014999] [drm:drm_client_modeset_probe] connector 212 enabled? no <7> [44.015030] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [44.015041] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185 <7> [44.015045] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0 <7> [44.015048] [drm:drm_client_modeset_probe] found mode 3840x2160 <7> [44.015051] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config <7> [44.015067] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0) <6> [44.057667] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100 <6> [44.057900] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <6> [44.061304] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [44.061590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [44.061914] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010 <7> [44.065753] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [44.067537] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [44.076358] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [44.078906] [drm:eb_lookup_vmas [i915]] EINVAL at eb_validate_vma:508 <6> [44.110985] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [44.111071] [IGT] i915_module_load: exiting, ret=0 <6> [44.114284] snd_hda_codec_realtek hdaudioC0D0: ALC711: SKU not ready 0x00000000 <6> [44.114814] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC711: line_outs=1 (0x21/0x0/0x0/0x0/0x0) type:hp <6> [44.114820] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0) <6> [44.114824] snd_hda_codec_realtek hdaudioC0D0: hp_outs=0 (0x0/0x0/0x0/0x0/0x0) <6> [44.114827] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0 <6> [44.114829] snd_hda_codec_realtek hdaudioC0D0: inputs: <6> [44.114832] snd_hda_codec_realtek hdaudioC0D0: Mic=0x19

<4> [42.354571] **********************************************************

<4> [42.354574] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [42.354578] ** trace_printk() being used. Allocating extra memory. **

<4> [42.354582] ** This means that this is a DEBUG kernel and it is **

<4> [42.354588] ** If you see this message and you are not debugging **

<4> [42.354590] ** the kernel, report this immediately to your vendor! **

<4> [42.354594] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [42.354596] **********************************************************

<7> [42.412787] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 2048K

<7> [42.413118] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:yes huc:yes slpc:yes)

<7> [42.413426] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found Alder Lake PCH

<7> [42.413727] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [42.414192] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [42.414463] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 19200 kHz

<7> [42.415083] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vcs2 fused off

<7> [42.415298] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vdbox enable: 0001, instances: 0001

<7> [42.415515] i915 0000:00:02.0: [drm:intel_engines_init_mmio [i915]] vebox enable: 0001, instances: 0001

<7> [42.416298] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [42.416547] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [42.416764] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 60M

<6> [42.416966] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [42.424421] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [42.424596] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = 0x0000000050200087

<7> [42.424907] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 61440K, usable: 59392K

<7> [42.425598] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0x44a70018

<7> [42.425940] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.1.0

<7> [42.426209] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [42.426543] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [42.426821] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [42.427120] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (RVDA)

<7> [42.427463] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [42.427690] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [42.427907] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 0: DCLK=2401 tRP=24 tRDPRE=20 tRAS=52 tRCD=24 tRC=76

<7> [42.428214] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 1: DCLK=4001 tRP=36 tRDPRE=24 tRAS=84 tRCD=36 tRC=120

<7> [42.428562] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 2: DCLK=4401 tRP=40 tRDPRE=28 tRAS=96 tRCD=40 tRC=136

<7> [42.428862] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] QGV 3: DCLK=4801 tRP=44 tRDPRE=28 tRAS=104 tRCD=44 tRC=148

<7> [42.429164] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 0: CLK=32

<7> [42.429472] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 1: CLK=38

<7> [42.429754] i915 0000:00:02.0: [drm:icl_get_qgv_points.constprop.0 [i915]] PSF GV 2: CLK=48

<7> [42.430034] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 0: num_planes=0 deratedbw=8478

<7> [42.430308] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 1: num_planes=0 deratedbw=11380

<7> [42.430598] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 2: num_planes=0 deratedbw=11556

<7> [42.430868] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / QGV 3: num_planes=0 deratedbw=11991

<7> [42.431140] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 0: num_planes=0 bw=34133

<7> [42.431407] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 1: num_planes=0 bw=40533

<7> [42.431682] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW0 / PSF GV 2: num_planes=0 bw=51200

<7> [42.431952] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 0: num_planes=4 deratedbw=10928

<7> [42.432225] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 1: num_planes=4 deratedbw=15758

<7> [42.432500] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 2: num_planes=4 deratedbw=16388

<7> [42.432764] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / QGV 3: num_planes=4 deratedbw=17250

<7> [42.433023] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 0: num_planes=4 bw=34133

<7> [42.433285] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 1: num_planes=4 bw=40533

<7> [42.433558] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW1 / PSF GV 2: num_planes=4 bw=51200

<7> [42.433821] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 0: num_planes=0 deratedbw=12772

<7> [42.434079] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 1: num_planes=0 deratedbw=19510

<7> [42.434338] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 2: num_planes=0 deratedbw=20720

<7> [42.434603] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / QGV 3: num_planes=0 deratedbw=22096

<7> [42.434861] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 0: num_planes=0 bw=34133

<7> [42.435118] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 1: num_planes=0 bw=40533

<7> [42.435378] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW2 / PSF GV 2: num_planes=0 bw=51200

<7> [42.435654] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 0: num_planes=0 deratedbw=13950

<7> [42.435915] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 1: num_planes=0 deratedbw=22146

<7> [42.436169] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 2: num_planes=0 deratedbw=23044

<7> [42.436445] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / QGV 3: num_planes=0 deratedbw=23044

<7> [42.436726] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 0: num_planes=0 bw=34133

<7> [42.436978] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 1: num_planes=0 bw=40533

<7> [42.437227] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW3 / PSF GV 2: num_planes=0 bw=51200

<7> [42.437520] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 0: num_planes=0 deratedbw=14624

<7> [42.437785] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 1: num_planes=0 deratedbw=23044

<7> [42.438068] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 2: num_planes=0 deratedbw=23044

<7> [42.438320] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / QGV 3: num_planes=0 deratedbw=23044

<7> [42.438595] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 0: num_planes=0 bw=34133

<7> [42.438861] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 1: num_planes=0 bw=40533

<7> [42.439121] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW4 / PSF GV 2: num_planes=0 bw=51200

<7> [42.439373] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 0: num_planes=0 deratedbw=14986

<7> [42.439634] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 1: num_planes=0 deratedbw=23044

<7> [42.439888] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 2: num_planes=0 deratedbw=23044

<7> [42.440139] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / QGV 3: num_planes=0 deratedbw=23044

<7> [42.440393] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 0: num_planes=0 bw=34133

<7> [42.440653] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 1: num_planes=0 bw=40533

<7> [42.440906] i915 0000:00:02.0: [drm:tgl_get_bw_info [i915]] BW5 / PSF GV 2: num_planes=0 bw=51200

<7> [42.441697] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [42.442034] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT ALDERLAKE-P ", BDB version 249

<7> [42.442343] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 6, min size 7)

<7> [42.442652] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 395, min size 5)

<7> [42.442933] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 100, min size 100)

<7> [42.443211] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [42.443529] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 812, min size 812)

<7> [42.443808] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 34, min size 34)

<7> [42.444073] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Generating LFP data table pointers

<7> [42.444347] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [42.444638] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1366, min size 1366)

<7> [42.444914] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 305, min size 305)

<7> [42.445174] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 78, min size 78)

<7> [42.445448] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 52 (size 822, min size 822)

<7> [42.445719] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 56 (size 210, min size 210)

<7> [42.445980] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 1 fdi_rx_polarity_inverted 0

<7> [42.446233] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [42.446500] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x1806

<7> [42.446785] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [42.447052] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [42.447314] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [42.447608] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [42.447869] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:1 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [42.448128] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port A VBT HDMI level shift: 0

<7> [42.448380] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [42.448643] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 0

<7> [42.448902] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0

<7> [42.449158] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port D VBT HDMI level shift: 0

<7> [42.449408] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:1 TBT:1 DSC:0

<7> [42.449671] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0

<7> [42.449935] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 4000000a

<7> [42.450232] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [42.450602] i915 0000:00:02.0: [drm:check_phy_reg [i915]] Combo PHY A reg 001628a0 state mismatch: current 90035b7c mask e0000000 expected a0000000

<7> [42.450879] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [42.451203] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [42.451497] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [42.451818] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [42.452125] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [42.452401] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf

<7> [42.452840] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [42.453112] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [42.453379] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [42.453711] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY A Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [42.453995] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY A already enabled, won't reprogram it.

<7> [42.454269] i915 0000:00:02.0: [drm:icl_verify_procmon_ref_values [i915]] Combo PHY B Voltage/Process Info : 0.85V dot0 (low-voltage)

<7> [42.454552] i915 0000:00:02.0: [drm:icl_combo_phys_init [i915]] Combo PHY B already enabled, won't reprogram it.

<7> [42.454815] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<6> [42.455104] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem

<7> [42.455150] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_A

<7> [42.455472] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_B

<7> [42.455758] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_C

<7> [42.456029] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_D

<7> [42.456411] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/adlp_dmc.bin

<7> [42.458951] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [42.460133] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 35 us

<7> [42.460477] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 3 (3.0 usec)

<7> [42.460816] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 54 (54.0 usec)

<7> [42.461157] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 83 (83.0 usec)

<7> [42.461509] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 102 (102.0 usec)

<7> [42.461840] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 147 (147.0 usec)

<7> [42.462165] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 147 (147.0 usec)

<6> [42.464719] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/adlp_dmc.bin (v2.19)

<7> [42.476033] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.

<7> [42.480537] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 307200 kHz, VCO 614400 kHz, ref 38400 kHz, bypass 19200 kHz, voltage level 0

<7> [42.481193] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind

<6> [42.481868] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

<7> [42.482147] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 652800 kHz

<7> [42.482486] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] Max dotclock rate: 1305600 kHz

<7> [42.482853] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:184:DDI A/PHY A] using AUX A (VBT)

<7> [42.483190] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding eDP connector on [ENCODER:184:DDI A/PHY A]

<7> [42.483639] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel type (VBT): 2

<7> [42.483984] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Selected panel type (VBT): 2

<7> [42.484317] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] DRRS supported mode is seamless

<7> [42.484664] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Found panel mode in BIOS VBT legacy lfp table: "1024x768": 60 65000 1024 1048 1184 1344 768 771 777 806 0x8 0xa

<7> [42.484991] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT initial LVDS value 300

<7> [42.485308] i915 0000:00:02.0: [drm:dump_pnp_id [i915]] Panel PNPID mfg: MS_ (0x7f36), prod: 3, serial: 3, week: 0, year: 2002

<7> [42.485663] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Panel name: LFP_PanelName

<7> [42.485981] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] Seamless DRRS min refresh rate: 0 Hz

<7> [42.486295] i915 0000:00:02.0: [drm:intel_bios_init_panel [i915]] VBT backlight PWM modulation frequency 200 Hz, active high, min brightness 6, level 255, controller 0

<7> [42.486702] i915 0000:00:02.0: [drm:intel_pps_init [i915]] [ENCODER:184:DDI A/PHY A] initial power sequencer: PPS 0

<7> [42.487077] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000

<7> [42.487358] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [42.487667] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [42.487959] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [42.488215] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [42.488643] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [42.489026] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [42.489531] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on

<7> [42.489907] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006f

<7> [42.491787] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 00 44 41 00 00 01 c0 02 00 02 00 00 0b 80

<7> [42.492470] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX A/DDI A/PHY A: DP sink: OUI 38-ec-11 dev-ID HW-rev 0.0 SW-rev 0.0 quirks 0x0000

<7> [42.492979] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] eDP DPCD: 04 92 a5

<7> [42.493704] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] eDP panel supports PSR version 3

<7> [42.494945] i915 0000:00:02.0: [drm:intel_psr_init_dpcd [i915]] PSR2 supported

<7> [42.497027] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [42.497298] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] FEC CAPABILITY: 0

<7> [42.508240] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [42.508262] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [42.508269] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [42.508275] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [42.508383] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using preferred EDID fixed mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [42.508680] i915 0000:00:02.0: [drm:intel_panel_add_edid_fixed_modes [i915]] [CONNECTOR:185:eDP-1] using alternate EDID fixed mode: "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [42.509466] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms)

<7> [42.510237] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Detected Intel HDR backlight interface version 1

<7> [42.510503] i915 0000:00:02.0: [drm:intel_dp_aux_init_backlight_funcs [i915]] [CONNECTOR:185:eDP-1] Using Intel proprietary eDP backlight controls

<7> [42.510758] i915 0000:00:02.0: [drm:intel_panel_init [i915]] [CONNECTOR:185:eDP-1] DRRS type: seamless

<7> [42.511056] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] SDR backlight is controlled through PWM

<7> [42.511361] i915 0000:00:02.0: [drm:cnp_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using native PCH PWM for backlight control (controller=0)

<7> [42.511636] i915 0000:00:02.0: [drm:intel_dp_aux_hdr_setup_backlight [i915]] [CONNECTOR:185:eDP-1] Using AUX HDR interface for backlight control (range 0..552)

<7> [42.512570] i915 0000:00:02.0: [drm:intel_backlight_setup [i915]] [CONNECTOR:185:eDP-1] backlight initialized, enabled, brightness 552/552

<7> [42.512903] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] bios t1_t3 1 t8 1 t9 1 t10 500 t11_t12 6000

<7> [42.513157] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] vbt t1_t3 2000 t8 10 t9 2000 t10 500 t11_t12 6000

<7> [42.513402] i915 0000:00:02.0: [drm:intel_pps_dump_state [i915]] spec t1_t3 2100 t8 500 t9 500 t10 5000 t11_t12 6100

<7> [42.513657] i915 0000:00:02.0: [drm:pps_init_delays [i915]] panel power up delay 200, power down delay 50, power cycle delay 600

<7> [42.513911] i915 0000:00:02.0: [drm:pps_init_delays [i915]] backlight on delay 1, off delay 200

<7> [42.514263] i915 0000:00:02.0: [drm:pps_init_registers [i915]] panel power sequencer register settings: PP_ON 0x7d00001, PP_OFF 0x1f40001, PP_DIV 0x60

<7> [42.514838] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:193:DDI B/PHY B] using AUX B (platform default)

<7> [42.515116] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:193:DDI B/PHY B]

<7> [42.515361] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:193:DDI B/PHY B] Using DDC pin 0x2 (VBT)

<7> [42.515857] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:202:DDI TC1/PHY TC1] using AUX D (VBT)

<7> [42.516401] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port D/TC#1: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)

<7> [42.516770] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:202:DDI TC1/PHY TC1]

<7> [42.517349] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:211:DDI TC2/PHY TC2] using AUX E (VBT)

<7> [42.517669] i915 0000:00:02.0: [drm:tc_phy_get_current_mode [i915]] Port E/TC#2: PHY mode: tbt-alt (ready: yes, owned: no, HPD: disconnected)

<7> [42.517999] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:211:DDI TC2/PHY TC2]

<7> [42.518508] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port F is not present

<7> [42.518790] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port G is not present

<7> [42.519569] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:80:pipe A] hw state readout: enabled

<7> [42.520003] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:131:pipe B] hw state readout: disabled

<7> [42.520425] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:182:pipe C] hw state readout: disabled

<7> [42.520724] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: enabled, pipe A

<7> [42.521016] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] hw state readout: disabled, pipe A

<7> [42.521297] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] hw state readout: disabled, pipe A

<7> [42.521594] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] hw state readout: disabled, pipe A

<7> [42.521874] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] hw state readout: disabled, pipe A

<7> [42.522150] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] hw state readout: disabled, pipe A

<7> [42.522445] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] hw state readout: disabled, pipe B

<7> [42.522726] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] hw state readout: disabled, pipe B

<7> [42.522993] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] hw state readout: disabled, pipe B

<7> [42.523267] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] hw state readout: disabled, pipe B

<7> [42.523563] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] hw state readout: disabled, pipe B

<7> [42.523838] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] hw state readout: disabled, pipe B

<7> [42.524105] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] hw state readout: disabled, pipe C

<7> [42.524377] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] hw state readout: disabled, pipe C

<7> [42.524674] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] hw state readout: disabled, pipe C

<7> [42.524945] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] hw state readout: disabled, pipe C

<7> [42.525213] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] hw state readout: disabled, pipe C

<7> [42.525504] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] hw state readout: disabled, pipe C

<7> [42.525847] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0

<7> [42.526117] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 24 bpp for eDP panel, overriding BIOS-provided max 18 bpp

<7> [42.526497] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:184:DDI A/PHY A] hw state readout: enabled, pipe A

<7> [42.526786] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:193:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [42.527102] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port D/TC#1: sanitize mode (disconnected)

<7> [42.527371] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:202:DDI TC1/PHY TC1] hw state readout: disabled, pipe A

<7> [42.527658] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:204:DP-MST A] hw state readout: disabled, pipe A

<7> [42.527924] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:205:DP-MST B] hw state readout: disabled, pipe B

<7> [42.528177] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:206:DP-MST C] hw state readout: disabled, pipe C

<7> [42.528474] i915 0000:00:02.0: [drm:intel_tc_port_sanitize_mode [i915]] Port E/TC#2: sanitize mode (disconnected)

<7> [42.528736] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:211:DDI TC2/PHY TC2] hw state readout: disabled, pipe A

<7> [42.528996] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:213:DP-MST A] hw state readout: disabled, pipe A

<7> [42.529259] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:214:DP-MST B] hw state readout: disabled, pipe B

<7> [42.529572] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:215:DP-MST C] hw state readout: disabled, pipe C

<7> [42.529856] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x1, on 1

<7> [42.530142] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [42.530428] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TBT PLL hw state readout: pipe_mask 0x0, on 0

<7> [42.530744] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [42.531032] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [42.531306] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [42.531608] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] TC PLL 4 hw state readout: pipe_mask 0x0, on 0

<7> [42.532046] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:185:eDP-1] hw state readout: enabled

<7> [42.532351] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:194:HDMI-A-1] hw state readout: disabled

<7> [42.532664] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:203:DP-1] hw state readout: disabled

<7> [42.532952] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:212:DP-2] hw state readout: disabled

<7> [42.533368] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 269300 kHz

<7> [42.533659] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:40:plane 2A] min_cdclk 0 kHz

<7> [42.533937] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:49:plane 3A] min_cdclk 0 kHz

<7> [42.534185] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:58:plane 4A] min_cdclk 0 kHz

<7> [42.534447] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:67:plane 5A] min_cdclk 0 kHz

<7> [42.534705] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:76:cursor A] min_cdclk 0 kHz

<7> [42.534962] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 2154400 num active planes 1

<7> [42.535266] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:82:plane 1B] min_cdclk 0 kHz

<7> [42.535545] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:91:plane 2B] min_cdclk 0 kHz

<7> [42.535802] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:100:plane 3B] min_cdclk 0 kHz

<7> [42.536056] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:109:plane 4B] min_cdclk 0 kHz

<7> [42.536308] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:118:plane 5B] min_cdclk 0 kHz

<7> [42.536576] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:127:cursor B] min_cdclk 0 kHz

<7> [42.536827] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [42.537121] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:133:plane 1C] min_cdclk 0 kHz

<7> [42.537381] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:142:plane 2C] min_cdclk 0 kHz

<7> [42.537648] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:151:plane 3C] min_cdclk 0 kHz

<7> [42.537898] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:160:plane 4C] min_cdclk 0 kHz

<7> [42.538152] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:169:plane 5C] min_cdclk 0 kHz

<7> [42.538399] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:178:cursor C] min_cdclk 0 kHz

<7> [42.538658] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [42.538965] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [42.539499] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [setup_hw_state]

<7> [42.539805] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB

<7> [42.540093] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 24, dithering: 0

<7> [42.540377] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [42.540675] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [42.540959] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [42.541240] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [42.541534] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 653660, link_n: 524288, tu: 64

<7> [42.541814] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [42.542092] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [42.542371] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x0

<7> [42.542660] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0

<7> [42.542942] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [42.543219] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [42.543520] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [42.543800] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [42.544071] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [42.544346] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 432000, pipe src: 3840x2160+0+0, pixel rate 538600

<7> [42.544641] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0

<7> [42.544919] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [42.545186] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [42.545470] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [42.545747] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0x1c2, cfgcr1: 0x84, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [42.546027] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x20000000 gamma_mode: 0x20000000 gamma_enable: 0 csc_enable: 0

<7> [42.546300] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [42.546588] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:131:pipe B] enable: no [setup_hw_state]

<7> [42.546878] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:182:pipe C] enable: no [setup_hw_state]

<7> [42.547292] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:80:pipe A] dbuf slices 0x3, ddb (0 - 2048), active pipes 0x1, mbus joined: no

<7> [42.547587] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:131:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [42.547863] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:182:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x1, mbus joined: no

<7> [42.548523] i915 0000:00:02.0: [drm:skl_get_initial_plane_config [i915]] pipe A/plane 1A with fb: size=3840x2160@32, offset=0, pitch 15360, size 0x1fa4000

<7> [42.548800] i915 0000:00:02.0: [drm:intel_plane_disable_noatomic [i915]] Disabling [PLANE:31:plane 1A] on [CRTC:80:pipe A]

<7> [42.574833] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [592K, 1420K)

<7> [42.575170] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [42.575449] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]

<7> [42.575712] MCR Steering: Default steering: group=0x0, instance=0x0

<7> [42.575731] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 3 GT workarounds on global

<7> [42.577376] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 11 engine workarounds on rcs'0

<7> [42.577683] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 4 whitelist workarounds on rcs'0

<7> [42.577959] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 context workarounds on rcs'0

<7> [42.579882] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on bcs'0

<7> [42.580166] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on bcs'0

<7> [42.580450] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 context workarounds on bcs'0

<7> [42.581196] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vcs'0

<7> [42.581479] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vcs'0

<7> [42.582177] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 engine workarounds on vecs'0

<7> [42.582458] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 1 whitelist workarounds on vecs'0

<7> [42.585282] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)

<7> [42.585708] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset

<7> [42.624045] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0x16304f

<7> [42.624416] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x44000

<7> [42.625113] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4

<7> [42.625455] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3

<7> [42.625755] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0xac8

<7> [42.626043] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x46d00000

<7> [42.626336] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0

<7> [42.626638] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0

<7> [42.626929] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0

<7> [42.627209] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0

<7> [42.627534] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0

<7> [42.627822] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0

<7> [42.628101] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0

<7> [42.628382] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0

<7> [42.628674] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no

<6> [42.630208] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/tgl_guc_70.bin version 70.5.1

<6> [42.630215] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/tgl_huc.bin version 7.9.3

<7> [42.633453] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 1ms, freq = 750MHz, before = 750MHz, status = 0x8002F0EC, count = 0, ret = 0

<7> [42.634824] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<6> [42.637544] i915 0000:00:02.0: [drm] GT0: GUC: submission enabled

<7> [42.647704] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [42.648323] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [42.648750] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz

<7> [42.649110] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30

<7> [42.649479] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000

<7> [42.649835] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no

<7> [42.650179] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [42.650574] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A]

<7> [42.650923] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048)

<7> [42.651287] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5)

<7> [42.651674] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 24, found 30)

<7> [42.652045] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 432000, found 540000)

<7> [42.652398] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] releasing DPLL 0

<7> [42.652810] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes

<7> [42.653163] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1

<7> [42.653627] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [42.654045] i915 0000:00:02.0: [drm:intel_dp_initial_fastset_check [i915]] [ENCODER:184:DDI A/PHY A] Forcing full modeset to compute PSR state

<7> [42.654471] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [42.654848] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz

<7> [42.655177] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30

<7> [42.655510] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000

<7> [42.655850] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no

<7> [42.656176] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [42.656543] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A]

<7> [42.656873] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr1 (expected 0x00000084, found 0x00000048)

<7> [42.657227] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in dpll_hw_state.cfgcr0 (expected 0x000001c2, found 0x00e001a5)

<7> [42.657593] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in pipe_bpp (expected 24, found 30)

<7> [42.657940] i915 0000:00:02.0: [drm:pipe_config_mismatch [i915]] [CRTC:80:pipe A] fastset mismatch in port_clock (expected 432000, found 540000)

<7> [42.658286] i915 0000:00:02.0: [drm:intel_unreference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] releasing DPLL 0

<7> [42.658675] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] Enabled dbuf slices 0xf -> 0xf (total dbuf slices 0xf), mbus joined? no->yes

<7> [42.659011] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [CRTC:80:pipe A] dbuf slices 0x3 -> 0xf, ddb (0 - 2048) -> (0 - 4096), active pipes 0x1 -> 0x1

<7> [42.659423] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 2048) -> ( 0 - 0), size 2048 -> 0

<7> [42.659782] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] ddb ( 0 - 0) -> (4027 - 4096), size 0 -> 69

<7> [42.660108] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level *wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm,*swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [42.660425] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 6, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.660768] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 32, 32, 7, 7, 7, 7, 0, 0, 7, 187, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.661098] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.661445] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [42.661786] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.662101] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.662420] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:40:plane 2A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.662763] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [42.663084] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.663393] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.663741] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:49:plane 3A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.664061] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [42.664370] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.664699] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.665017] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:58:plane 4A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.665330] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [42.665661] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.665975] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.666286] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:67:plane 5A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.666615] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm

<7> [42.666935] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] lines 1, 1, 1, 1, 1, 1, 0, 0, 1, 1, 1 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.667242] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] blocks 7, 7, 7, 7, 7, 7, 0, 0, 7, 7, 7 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.667563] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:76:cursor A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0

<7> [42.667920] i915 0000:00:02.0: [drm:intel_find_shared_dpll [i915]] [CRTC:80:pipe A] allocated DPLL 0

<7> [42.668262] i915 0000:00:02.0: [drm:intel_reference_shared_dpll.isra.0 [i915]] [CRTC:80:pipe A] reserving DPLL 0

<6> [42.668618] i915 0000:00:02.0: [drm] Selective fetch area calculation failed in pipe A

<7> [42.668626] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [modeset]

<7> [42.668973] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB

<7> [42.669313] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [42.669666] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [42.669999] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [42.670330] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [42.670678] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [42.671013] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64

<7> [42.671337] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [42.671686] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [42.672021] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [42.672343] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0

<7> [42.672369] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0

<7> [42.672714] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [42.673049] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [42.673381] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [42.673731] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [42.674062] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [42.674384] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600

<7> [42.674735] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0

<7> [42.675064] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [42.675380] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [42.675718] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [42.676049] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [42.676381] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [42.676713] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [42.677042] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [NOFB], visible: no

<7> [42.677366] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [42.677936] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [42.678288] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [42.678989] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [42.679338] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [42.681766] i915 0000:00:02.0: [drm:intel_edp_backlight_off [i915]]

<7> [42.887547] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 0

<7> [42.888407] i915 0000:00:02.0: [drm:intel_disable_transcoder [i915]] disabling pipe A

<7> [42.897094] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power off

<7> [42.897469] i915 0000:00:02.0: [drm:intel_pps_off_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power off time

<7> [42.897899] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb0000000 value: 0x00000000 PP_STATUS: 0xa0000002 PP_CONTROL: 0x00000060

<7> [42.951335] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [42.951679] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A

<7> [42.952217] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disable DPLL 0 (active 0x1, on? 1) for [CRTC:80:pipe A]

<7> [42.952607] i915 0000:00:02.0: [drm:intel_disable_shared_dpll [i915]] disabling DPLL 0

<7> [42.952912] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling AUX_A

<7> [42.953220] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A]

<7> [42.953528] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B]

<7> [42.953812] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1]

<7> [42.954086] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A]

<7> [42.954354] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B]

<7> [42.954634] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C]

<7> [42.954905] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2]

<7> [42.955169] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A]

<7> [42.955451] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B]

<7> [42.955714] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C]

<7> [42.955970] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [42.956259] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [42.956558] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL

<7> [42.956837] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1

<7> [42.957108] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2

<7> [42.957380] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3

<7> [42.957669] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4

<7> [42.957962] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf

<7> [42.958332] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling AUX_A

<7> [42.958631] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enable DPLL 0 (active 0x1, on? 0) for [CRTC:80:pipe A]

<7> [42.958906] i915 0000:00:02.0: [drm:intel_enable_shared_dpll [i915]] enabling DPLL 0

<7> [42.959319] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turn panel power on

<7> [42.959633] i915 0000:00:02.0: [drm:wait_panel_power_cycle [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power cycle

<7> [43.599876] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb800000f value: 0x00000000 PP_STATUS: 0x00000000 PP_CONTROL: 0x00000060

<7> [43.600375] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [43.600888] i915 0000:00:02.0: [drm:intel_pps_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 wait for panel power on

<7> [43.601374] i915 0000:00:02.0: [drm:wait_panel_status [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 mask: 0xb000000f value: 0x80000008 PP_STATUS: 0x9000000a PP_CONTROL: 0x00000063

<7> [43.813965] i915 0000:00:02.0: [drm:wait_panel_status [i915]] Wait complete

<7> [43.814870] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A

<7> [43.816144] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 turning VDD on

<7> [43.816990] i915 0000:00:02.0: [drm:intel_pps_vdd_on_unlocked [i915]] [ENCODER:184:DDI A/PHY A] PPS 0 PP_STATUS: 0x80000008 PP_CONTROL: 0x0000006b

<7> [43.819991] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX A/DDI A/PHY A: DPCD: 14 14 44 41 00 00 01 c0 02 00 02 00 00 0b 80

<7> [43.820066] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [CONNECTOR:185:eDP-1] Reloading eDP link rates

<7> [43.820992] i915 0000:00:02.0: [drm:intel_dp_start_link_train [i915]] [ENCODER:184:DDI A/PHY A] Using LINK_RATE_SET value 06

<7> [43.821852] i915 0000:00:02.0: [drm:intel_dp_set_signal_levels [i915]] [ENCODER:184:DDI A/PHY A][DPRX] 8b/10b, lanes: 4, vswing levels: 0/0/0/0, pre-emphasis levels: 0/0/0/0

<7> [43.822086] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS1

<7> [43.823288] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Clock recovery OK

<7> [43.823447] i915 0000:00:02.0: [drm:intel_dp_program_link_training_pattern [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Using DP training pattern TPS3

<7> [43.824911] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [ENCODER:184:DDI A/PHY A][DPRX] Channel EQ done. DP Training successful

<7> [43.825094] i915 0000:00:02.0: [drm:intel_dp_link_train_phy [i915]] [CONNECTOR:185:eDP-1][ENCODER:184:DDI A/PHY A][DPRX] Link Training passed at link rate = 540000, lane count = 4

<7> [43.825632] i915 0000:00:02.0: [drm:intel_enable_transcoder [i915]] enabling pipe A

<7> [43.825992] i915 0000:00:02.0: [drm:intel_edp_backlight_on [i915]]

<7> [43.826154] i915 0000:00:02.0: [drm:intel_backlight_enable [i915]] pipe A

<7> [43.826313] i915 0000:00:02.0: [drm:intel_dp_wait_source_oui [i915]] [CONNECTOR:185:eDP-1] Performing OUI wait (0 ms)

<7> [43.827120] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000

<7> [43.842777] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0xf

<7> [43.843346] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1]

<7> [43.843730] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [43.844999] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0

<7> [43.845454] i915 0000:00:02.0: [drm:intel_edp_fixup_vbt_bpp [i915]] pipe has 30 bpp for eDP panel, overriding BIOS-provided max 24 bpp

<7> [43.845968] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [43.846865] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [PLANE:31:plane 1A] no fb, skipping

<7> [43.847277] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:131:pipe B] not active, skipping

<7> [43.847669] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:182:pipe C] not active, skipping

<7> [43.848034] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [43.849901] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [43.850256] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [43.850601] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [43.850847] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [43.863675] i915 0000:00:02.0: [drm:intel_backlight_device_register [i915]] [CONNECTOR:185:eDP-1] backlight device intel_backlight registered

<7> [43.864384] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI A/PHY A bus for card0-eDP-1

<7> [43.867110] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:185:eDP-1] generating connector hotplug event

<7> [43.867958] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:194:HDMI-A-1] generating connector hotplug event

<7> [43.868901] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC1/DDI TC1/PHY TC1 bus for card0-DP-1

<7> [43.870658] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:203:DP-1] generating connector hotplug event

<7> [43.871560] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX USBC2/DDI TC2/PHY TC2 bus for card0-DP-2

<7> [43.873553] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:212:DP-2] generating connector hotplug event

<6> [43.873674] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [43.879207] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 4 outputs detected

<6> [43.898611] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [43.903025] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3

<7> [43.905531] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x8010 (init value 0x8010)

<7> [43.905776] i915 0000:00:02.0: [drm:intel_audio_init [i915]] aud_ts_cdclk set to M=60, N=768

<7> [43.906427] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_D

<7> [43.906720] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1]

<7> [43.906759] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1]

<7> [43.908958] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [43.909176] i915 device info: pciid=0x46d0 rev=0x00 platform=ALDERLAKE_P (subplatform=0x2) gen=12

<7> [43.909298] i915 device info: slice0: 2 subslices, mask=00000003

<6> [43.909310] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [43.909312] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [43.909470] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [43.909660] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [43.910319] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [43.910513] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [43.910688] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [43.910863] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000

<7> [43.911142] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [43.911152] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [43.911157] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [43.911161] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [43.911197] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no

<7> [43.911372] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [43.912160] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [43.912358] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [43.913666] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_B

<7> [43.914018] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_C

<7> [43.914247] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [43.914550] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] status updated from unknown to connected

<7> [43.915314] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] probed modes :

<7> [43.915336] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [43.915344] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [43.915350] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1]

<7> [43.915367] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1]

<7> [43.915703] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] status updated from unknown to disconnected

<7> [43.915726] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] disconnected

<7> [43.915749] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1]

<7> [43.915763] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1]

<7> [43.916049] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] status updated from unknown to disconnected

<7> [43.916071] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] disconnected

<7> [43.916090] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2]

<7> [43.916105] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2]

<7> [43.916937] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] status updated from unknown to disconnected

<7> [43.916962] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] disconnected

<7> [43.916981] [drm:drm_client_modeset_probe] connector 185 enabled? yes

<7> [43.916987] [drm:drm_client_modeset_probe] connector 194 enabled? no

<7> [43.916990] [drm:drm_client_modeset_probe] connector 203 enabled? no

<7> [43.916992] [drm:drm_client_modeset_probe] connector 212 enabled? no

<7> [43.917118] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [43.917142] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185

<7> [43.917146] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0

<7> [43.917149] [drm:drm_client_modeset_probe] found mode 3840x2160

<7> [43.917151] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [43.917162] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0)

<7> [43.917222] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<7> [43.917283] i915 0000:00:02.0: [drm:intelfb_create [i915]] no BIOS fb, allocating a new one

<7> [43.934226] i915 0000:00:02.0: [drm:intelfb_create [i915]] allocated 3840x2160 fb: 0x00e80000

<7> [43.939332] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CONNECTOR:185:eDP-1] Limiting display bpp to 30 (EDID bpp 30, max requested bpp 36, max platform bpp 36)

<7> [43.939773] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link computation with max lane count 4 max rate 810000 max bpp 30 pixel clock 538600KHz

<7> [43.939958] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP lane count 4 clock 540000 bpp 30

<7> [43.940134] i915 0000:00:02.0: [drm:intel_dp_compute_link_config [i915]] DP link rate required 2019750 available 2160000

<7> [43.940310] i915 0000:00:02.0: [drm:intel_dp_compute_config [i915]] [CONNECTOR:185:eDP-1] SDP split enable: no

<7> [43.940943] i915 0000:00:02.0: [drm:intel_atomic_check [i915]] [CRTC:80:pipe A] hw max bpp: 30, pipe bpp: 30, dithering: 0

<7> [43.941160] i915 0000:00:02.0: [drm:intel_ddi_compute_config_late [i915]] [ENCODER:184:DDI A/PHY A] [CRTC:80:pipe A]

<7> [43.941424] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] ddb ( 0 - 0) -> ( 0 - 4027), size 0 -> 4027

<7> [43.941888] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] level wm0, wm1, wm2, wm3, wm4, wm5, wm6, wm7, twm, swm, stwm -> *wm0,*wm1,*wm2,*wm3,*wm4,*wm5, wm6, wm7,*twm,*swm,*stwm

<7> [43.942085] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] lines 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 1, 8, 12, 14, 20, 20, 0, 0, 0, 6, 0

<7> [43.942260] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] blocks 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 31, 249, 373, 435, 621, 621, 0, 0, 45, 187, 201

<7> [43.942844] i915 0000:00:02.0: [drm:skl_compute_wm [i915]] [PLANE:31:plane 1A] min_ddb 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 -> 36, 275, 412, 480, 685, 685, 0, 0, 46, 207, 207

<7> [43.943036] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] [CRTC:80:pipe A] data rate 2154400 num active planes 1

<7> [43.943225] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 0: max bw 10928 required 2263

<7> [43.943407] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 1: max bw 15758 required 2263

<7> [43.943682] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 2: max bw 16388 required 2263

<7> [43.943872] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] QGV point 3: max bw 17250 required 2263

<7> [43.944063] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 0: max bw 34133 required 2263

<7> [43.944246] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 1: max bw 40533 required 2263

<7> [43.944427] i915 0000:00:02.0: [drm:intel_bw_atomic_check [i915]] PSF GV point 2: max bw 51200 required 2263

<7> [43.944684] i915 0000:00:02.0: [drm:intel_bw_calc_min_cdclk [i915]] new bandwidth min cdclk (42079 kHz) > old min cdclk (0 kHz)

<7> [43.944883] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:80:pipe A] enable: yes [fastset]

<7> [43.945072] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] active: yes, output_types: EDP (0x100), output format: RGB

<7> [43.945255] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] cpu_transcoder: A, pipe bpp: 30, dithering: 0

<7> [43.945486] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] MST master transcoder: <invalid>

<7> [43.945674] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port sync: master transcoder: <invalid>, slave transcoder bitmask = 0x0

<7> [43.945859] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] bigjoiner: no, pipes: 0x0

<7> [43.946043] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] splitter: disabled, link count 0, overlap 0

<7> [43.946230] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m_n: lanes: 4; data_m: 7843931, data_n: 8388608, link_m: 522928, link_n: 524288, tu: 64

<7> [43.946417] i915 0000:00:02.0: [drm:intel_dump_m_n_config.isra.0 [i915]] dp m2_n2: lanes: 4; data_m: 0, data_n: 0, link_m: 0, link_n: 0, tu: 0

<7> [43.946648] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] framestart delay: 1, MSA timing delay: 0

<7> [43.946834] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] audio: 0, infoframes: 0, infoframes enabled: 0x4

<7> [43.947018] i915 0000:00:02.0: DP SDP: VSC, revision 0, length 0

<7> [43.947031] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] vrr: no, vmin: 0, vmax: 0, pipeline full: 0, guardband: 0 flipline: 0, vmin vblank: 1, vmax vblank: 0

<7> [43.947207] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] requested mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [43.947393] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] adjusted mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [43.947625] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [43.947808] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pipe mode: "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [43.947991] i915 0000:00:02.0: [drm:intel_dump_crtc_timings [i915]] crtc timings: clock=538600, hd=3840 hb=3840-4000 hs=3888-3920 ht=4000, vd=2160 vb=2160-2244 vs=2163-2168 vt=2244, flags=0xa

<7> [43.948169] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] port clock: 540000, pipe src: 3840x2160+0+0, pixel rate 538600

<7> [43.948343] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] linetime: 60, ips linetime: 0

<7> [43.948562] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] num_scalers: 2, scaler_users: 0x0, scaler_id: -1, scaling_filter: 0

<7> [43.948734] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pch pfit: 0x0+0+0, disabled, force thru: no

<7> [43.948906] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] ips: 0, double wide: 0, drrs: 0

<7> [43.949086] i915 0000:00:02.0: [drm:icl_dump_hw_state [i915]] dpll_hw_state: cfgcr0: 0xe001a5, cfgcr1: 0x48, div0: 0x0, mg_refclkin_ctl: 0x0, hg_clktop2_coreclkctl1: 0x0, mg_clktop2_hsclkctl: 0x0, mg_pll_div0: 0x0, mg_pll_div2: 0x0, mg_pll_lf: 0x0, mg_pll_frac_lock: 0x0, mg_pll_ssc: 0x0, mg_pll_bias: 0x0, mg_pll_tdc_coldst_bias: 0x0

<7> [43.949267] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] csc_mode: 0x0 gamma_mode: 0x0 gamma_enable: 0 csc_enable: 0

<7> [43.949480] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] pre csc lut: 0 entries, post csc lut: 0 entries

<7> [43.949657] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:31:plane 1A] fb: [FB:186] 3840x2160 format = XR24 little-endian (0x34325258) modifier = 0x0, visible: yes

<7> [43.949834] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] rotation: 0x1, scaler: -1, scaling_filter: 0

<7> [43.950003] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] src: 3840.000000x2160.000000+0.000000+0.000000 dst: 3840x2160+0+0

<7> [43.950174] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:40:plane 2A] fb: [NOFB], visible: no

<7> [43.950345] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:49:plane 3A] fb: [NOFB], visible: no

<7> [43.950557] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:58:plane 4A] fb: [NOFB], visible: no

<7> [43.950729] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:67:plane 5A] fb: [NOFB], visible: no

<7> [43.950897] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [PLANE:76:cursor A] fb: [NOFB], visible: no

<7> [43.951648] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:184:DDI A/PHY A]

<7> [43.951836] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:193:DDI B/PHY B]

<7> [43.952006] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:202:DDI TC1/PHY TC1]

<7> [43.952173] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:204:DP-MST A]

<7> [43.952338] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:205:DP-MST B]

<7> [43.952564] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:206:DP-MST C]

<7> [43.952736] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:211:DDI TC2/PHY TC2]

<7> [43.952902] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:213:DP-MST A]

<7> [43.953068] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:214:DP-MST B]

<7> [43.953233] i915 0000:00:02.0: [drm:intel_modeset_verify_disabled [i915]] [ENCODER:215:DP-MST C]

<7> [43.953403] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [43.953814] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 1

<7> [43.954007] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TBT PLL

<7> [43.954185] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 1

<7> [43.954363] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 2

<7> [43.954652] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 3

<7> [43.954837] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] TC PLL 4

<7> [43.959247] i915 0000:00:02.0: [drm:intel_psr_post_plane_update [i915]] Enabling PSR2

<7> [43.960892] i915 0000:00:02.0: [drm:verify_connector_state [i915]] [CONNECTOR:185:eDP-1]

<7> [43.961128] i915 0000:00:02.0: [drm:intel_modeset_verify_crtc [i915]] [CRTC:80:pipe A]

<7> [43.961695] i915 0000:00:02.0: [drm:intel_ddi_get_config [i915]] [ENCODER:184:DDI A/PHY A] Fec status: 0

<7> [43.961909] i915 0000:00:02.0: [drm:verify_single_dpll_state.isra.0 [i915]] DPLL 0

<7> [43.962492] i915 0000:00:02.0: [drm:intel_backlight_device_update_status [i915]] updating intel_backlight, brightness=552/552

<7> [43.962679] i915 0000:00:02.0: [drm:intel_panel_actually_set_backlight [i915]] [CONNECTOR:185:eDP-1] set backlight level = 552

<7> [43.962856] i915 0000:00:02.0: [drm:intel_backlight_set_pwm_level [i915]] [CONNECTOR:185:eDP-1] set backlight PWM = 96000

<6> [43.964111] Console: switching to colour frame buffer device 480x135

<6> [43.984055] i915 0000:00:02.0: [drm] fb0: i915drmfb frame buffer device

<7> [43.997556] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]

<7> [43.997749] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1]

<7> [43.997781] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1]

<7> [43.998837] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [43.998991] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [43.999624] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [43.999767] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [43.999902] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [44.000034] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000

<7> [44.000278] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [44.000286] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [44.000290] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [44.000293] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [44.000319] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no

<7> [44.000466] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [44.001223] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [44.001359] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [44.002225] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] probed modes :

<7> [44.002250] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [44.002256] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [44.002260] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1]

<7> [44.002275] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1]

<7> [44.002504] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] disconnected

<7> [44.002521] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1]

<7> [44.002534] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1]

<7> [44.002763] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] disconnected

<7> [44.002778] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2]

<7> [44.002791] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2]

<7> [44.002966] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] disconnected

<7> [44.002979] [drm:drm_client_modeset_probe] connector 185 enabled? yes

<7> [44.002983] [drm:drm_client_modeset_probe] connector 194 enabled? no

<7> [44.002985] [drm:drm_client_modeset_probe] connector 203 enabled? no

<7> [44.002987] [drm:drm_client_modeset_probe] connector 212 enabled? no

<7> [44.003064] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [44.003080] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185

<7> [44.003082] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0

<7> [44.003084] [drm:drm_client_modeset_probe] found mode 3840x2160

<7> [44.003086] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config

<7> [44.003116] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0)

<7> [44.009849] i915 0000:00:02.0: [drm:drm_fb_helper_hotplug_event.part.0 [drm_kms_helper]]

<7> [44.009905] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1]

<7> [44.009924] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:185:eDP-1]

<7> [44.010828] i915 0000:00:02.0: [drm:intel_dp_get_dsc_sink_cap [i915]] DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [44.010990] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] FEC CAPABILITY: 0

<7> [44.011593] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [ENCODER:184:DDI A/PHY A] MST support: port: no, sink: no, modparam: yes

<7> [44.011750] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] source rates: 162000, 216000, 270000, 324000, 432000, 540000, 648000, 810000

<7> [44.011905] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] sink rates: 162000, 216000, 243000, 270000, 324000, 432000, 540000, 810000

<7> [44.012049] i915 0000:00:02.0: [drm:intel_dp_print_rates [i915]] common rates: 162000, 216000, 270000, 324000, 432000, 540000, 810000

<7> [44.012219] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Supported Monitor Refresh rate range is 0 Hz - 0 Hz

<7> [44.012228] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] Assigning EDID-1.4 digital sink color depth as 10 bpc.

<7> [44.012233] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD monitor

<7> [44.012238] i915 0000:00:02.0: [drm:update_display_info] [CONNECTOR:185:eDP-1] ELD size 20, SAD count 0

<7> [44.012259] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] VRR capable: no

<7> [44.012404] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] DFP max bpc 0, max dotclock 0, TMDS clock 0-0, PCON Max FRL BW 0Gbps

<7> [44.013252] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] PCON ENCODER DSC DPCD: 00 00 00 00 00 00 00 00 00 00 00 00 00

<7> [44.013404] i915 0000:00:02.0: [drm:intel_dp_set_edid [i915]] [CONNECTOR:185:eDP-1] RGB->YcbCr conversion? no, YCbCr 4:2:0 allowed? yes, YCbCr 4:4:4->4:2:0 conversion? no

<7> [44.014157] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:185:eDP-1] probed modes :

<7> [44.014178] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 60 538600 3840 3888 3920 4000 2160 2163 2168 2244 0x48 0xa

<7> [44.014185] [drm:drm_mode_debug_printmodeline] Modeline "3840x2160": 40 359070 3840 3888 3920 4000 2160 2163 2168 2244 0x40 0xa

<7> [44.014191] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1]

<7> [44.014209] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:194:HDMI-A-1]

<7> [44.014392] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:194:HDMI-A-1] disconnected

<7> [44.014410] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1]

<7> [44.014426] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:203:DP-1]

<7> [44.014761] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:203:DP-1] disconnected

<7> [44.014777] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2]

<7> [44.014793] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:212:DP-2]

<7> [44.014973] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:212:DP-2] disconnected

<7> [44.014988] [drm:drm_client_modeset_probe] connector 185 enabled? yes

<7> [44.014993] [drm:drm_client_modeset_probe] connector 194 enabled? no

<7> [44.014996] [drm:drm_client_modeset_probe] connector 203 enabled? no

<7> [44.014999] [drm:drm_client_modeset_probe] connector 212 enabled? no

<7> [44.015030] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [44.015041] [drm:drm_client_modeset_probe] looking for cmdline mode on connector 185

<7> [44.015045] [drm:drm_client_modeset_probe] looking for preferred mode on connector 185 0

<7> [44.015048] [drm:drm_client_modeset_probe] found mode 3840x2160

<7> [44.015051] [drm:drm_client_modeset_probe] picking CRTCs for 3840x2160 config

<7> [44.015067] [drm:drm_client_modeset_probe] desired mode 3840x2160 set on crtc 80 (0,0)

<6> [44.057667] snd_hda_intel 0000:00:1f.3: DSP detected with PCI class/subclass/prog-if info 0x040100

<6> [44.057900] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)

<6> [44.061304] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [44.061590] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [44.061914] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x8010

<7> [44.067537] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [44.078906] [drm:eb_lookup_vmas [i915]] EINVAL at eb_validate_vma:508

<6> [44.110985] [IGT] i915_module_load: finished subtest load, SUCCESS

<6> [44.114284] snd_hda_codec_realtek hdaudioC0D0: ALC711: SKU not ready 0x00000000

<6> [44.114814] snd_hda_codec_realtek hdaudioC0D0: autoconfig for ALC711: line_outs=1 (0x21/0x0/0x0/0x0/0x0) type:hp

<6> [44.114820] snd_hda_codec_realtek hdaudioC0D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)

<6> [44.114824] snd_hda_codec_realtek hdaudioC0D0: hp_outs=0 (0x0/0x0/0x0/0x0/0x0)

<6> [44.114827] snd_hda_codec_realtek hdaudioC0D0: mono: mono_out=0x0

Results for igt@i915_module_load@load