igt@i915_module_load@load on fi-kbl-guc@linus-v6.4-rc7 Test details

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gb7d168f61 (x86_64) (Linux: 6.4.0-rc7-linus-v6.4-rc7-g45a3e24f65e9+ x86_64)
Out	Starting subtest: load Opened device: /dev/dri/card0 Subtest load: SUCCESS (0.835s)
Err	Starting subtest: load Subtest load: SUCCESS (0.835s)
Dmesg	<6> [40.646507] Console: switching to colour dummy device 80x25 <6> [40.646569] [IGT] i915_module_load: executing <6> [40.825790] [IGT] i915_module_load: starting subtest load <4> [41.332703] <4> [41.332711] ******************************************************** <4> [41.332713] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [41.332714] <4> [41.332716] trace_printk() being used. Allocating extra memory. <4> [41.332717] <4> [41.332719] This means that this is a DEBUG kernel and it is <4> [41.332720] unsafe for production use. <4> [41.332722] <4> [41.332723] If you see this message and you are not debugging <4> [41.332725] the kernel, report this immediately to your vendor! <4> [41.332726] <4> [41.332728] NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE <4> [41.332729] ****************************************************** <5> [41.343851] Setting dangerous option enable_guc - tainting kernel <7> [41.386268] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K <7> [41.386473] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no) <6> [41.386617] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A <7> [41.386629] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH <7> [41.386772] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT <7> [41.387063] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing <7> [41.387230] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 24000 kHz <7> [41.388186] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M <7> [41.388299] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M <7> [41.388405] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M <6> [41.388508] i915 0000:00:02.0: [drm] VT-d active for gfx access <6> [41.390850] i915 0000:00:02.0: vgaarb: deactivate vga console <6> [41.391445] i915 0000:00:02.0: [drm] Using Transparent Hugepages <7> [41.391464] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047 <7> [41.391605] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K <7> [41.391987] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018 <7> [41.392144] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0 <7> [41.392306] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported <7> [41.392480] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x <7> [41.392609] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported <7> [41.397858] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483 <7> [41.398008] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported <7> [41.398143] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported <7> [41.398286] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4) <7> [41.398414] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4 <7> [41.398514] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [41.398611] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [41.398717] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no <7> [41.398840] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no <7> [41.398960] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no <7> [41.399060] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no <7> [41.399175] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes <7> [41.399294] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2 <7> [41.399388] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no <7> [41.399900] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz <7> [41.400046] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206 <7> [41.400213] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7) <7> [41.400408] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5) <7> [41.400553] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100) <7> [41.400693] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19) <7> [41.400875] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812) <7> [41.401047] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34) <7> [41.401204] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148) <7> [41.401382] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366) <7> [41.401555] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305) <7> [41.401698] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78) <7> [41.401859] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0 <7> [41.402035] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2 <7> [41.402184] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [41.402346] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2 <7> [41.402548] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6 <7> [41.402719] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping <7> [41.402862] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [41.403000] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4 <7> [41.403137] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [41.403340] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8 <7> [41.403512] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0 <7> [41.403650] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0 <7> [41.403786] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02 <7> [41.403984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [41.404189] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1 <7> [41.404357] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO <7> [41.404553] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os <7> [41.405002] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz <7> [41.405201] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz <7> [41.405356] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1 <7> [41.405565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.405740] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [41.405878] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00 <7> [41.406024] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <6> [41.406227] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem <7> [41.406287] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E <7> [41.406445] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B <7> [41.406583] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C <7> [41.406720] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D <7> [41.406959] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin <7> [41.408549] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1 <7> [41.408996] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV <7> [41.409200] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us <7> [41.409387] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec) <7> [41.409570] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec) <7> [41.409718] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec) <7> [41.409846] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec) <7> [41.409973] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec) <7> [41.410099] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec) <7> [41.410267] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec) <7> [41.410452] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec) <6> [41.411866] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4) <7> [41.411994] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available. <7> [41.413186] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0 <7> [41.413440] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind <6> [41.413595] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915]) <7> [41.413706] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port A is not present <7> [41.413862] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (platform default) <7> [41.414003] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B] <7> [41.414128] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT) <7> [41.414668] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:104:DDI C/PHY C] using AUX C (platform default) <7> [41.414809] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C] <7> [41.414950] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT) <7> [41.415205] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present <7> [41.415361] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] using AUX A (VBT) <7> [41.415542] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E] <7> [41.415808] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported <7> [41.416241] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled <7> [41.416450] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled <7> [41.416612] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled <7> [41.416752] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A <7> [41.416923] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A <7> [41.417105] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A <7> [41.417284] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B <7> [41.417450] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B <7> [41.417637] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B <7> [41.417777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C <7> [41.417914] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C <7> [41.418050] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C <7> [41.418260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A <7> [41.418424] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A <7> [41.418562] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A <7> [41.418704] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1 <7> [41.418906] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0 <7> [41.419055] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0 <7> [41.419214] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0 <7> [41.419485] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled <7> [41.419640] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled <7> [41.419790] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled <7> [41.419979] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz <7> [41.420119] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz <7> [41.420263] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz <7> [41.420439] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0 <7> [41.420634] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz <7> [41.420779] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz <7> [41.420910] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz <7> [41.421039] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0 <7> [41.421201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz <7> [41.421391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz <7> [41.421533] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz <7> [41.421663] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0 <7> [41.421868] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state] <7> [41.422054] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state] <7> [41.422205] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state] <7> [41.422353] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling <7> [41.422542] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [41.422680] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [41.422809] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no <7> [41.428018] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [240K, 784K) <7> [41.428168] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture <7> [41.428327] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000] <7> [41.428451] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0 <7> [41.428588] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global <7> [41.429674] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0 <7> [41.429812] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0 <7> [41.429945] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0 <7> [41.433493] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3) <7> [41.433677] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset <7> [41.462307] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f <7> [41.462473] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0 <7> [41.462608] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000 <7> [41.462741] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3 <7> [41.462872] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a <7> [41.463003] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004 <7> [41.463134] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0 <7> [41.463283] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0 <7> [41.463470] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0 <7> [41.463635] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0 <7> [41.463768] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0 <7> [41.463900] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0 <7> [41.464059] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0 <7> [41.464248] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0 <7> [41.464383] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no <6> [41.465597] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1 <6> [41.465601] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0 <7> [41.478981] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 9ms, freq = 100MHz, before = 100MHz, status = 0x8002F0EC, count = 0, ret = 0 <7> [41.479893] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled <6> [41.490730] i915 0000:00:02.0: [drm] GT0: HuC: authenticated! <6> [41.490734] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled <6> [41.490737] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled <7> [41.498515] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV <7> [41.498761] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping <7> [41.498902] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping <7> [41.499036] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping <7> [41.499186] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config <7> [41.499396] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [41.500019] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0 <7> [41.500175] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0 <7> [41.500280] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0 <7> [41.500381] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0 <7> [41.504123] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event <7> [41.504560] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event <7> [41.504979] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1 <7> [41.505906] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event <6> [41.505972] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0 <7> [41.507888] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected <6> [41.523424] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no) <6> [41.525610] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3 <7> [41.527443] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10) <7> [41.528263] [drm:drm_client_modeset_probe] <7> [41.528223] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D <7> [41.528474] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [41.528435] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C <7> [41.528503] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [41.528634] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B <7> [41.528828] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E <7> [41.529568] [drm:intel_dsm_detect [i915]] no _DSM method for intel device <7> [41.529710] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9 <7> [41.529714] i915 device info: graphics version: 9 <7> [41.529716] i915 device info: media version: 9 <7> [41.529718] i915 device info: display version: 9 <7> [41.529720] i915 device info: graphics stepping: F0 <7> [41.529721] i915 device info: media stepping: F0 <7> [41.529723] i915 device info: display stepping: C0 <7> [41.529725] i915 device info: base die stepping: <7> [41.529727] i915 device info: gt: 2 <7> [41.529728] i915 device info: memory-regions: 0x21 <7> [41.529730] i915 device info: page-sizes: 0x11000 <7> [41.529732] i915 device info: platform: KABYLAKE <7> [41.529734] i915 device info: ppgtt-size: 48 <7> [41.529735] i915 device info: ppgtt-type: 2 <7> [41.529737] i915 device info: dma_mask_size: 39 <7> [41.529739] i915 device info: is_mobile: no <7> [41.529741] i915 device info: is_lp: no <7> [41.529742] i915 device info: require_force_probe: no <7> [41.529744] i915 device info: is_dgfx: no <7> [41.529746] i915 device info: has_64bit_reloc: yes <7> [41.529748] i915 device info: has_64k_pages: no <7> [41.529749] i915 device info: gpu_reset_clobbers_display: no <7> [41.529751] i915 device info: has_reset_engine: yes <7> [41.529753] i915 device info: has_3d_pipeline: yes <7> [41.529755] i915 device info: has_4tile: no <7> [41.529756] i915 device info: has_flat_ccs: no <7> [41.529758] i915 device info: has_global_mocs: no <7> [41.529760] i915 device info: has_gmd_id: no <7> [41.529761] i915 device info: has_gt_uc: yes <7> [41.529763] i915 device info: has_heci_pxp: no <7> [41.529765] i915 device info: has_heci_gscfi: no <7> [41.529766] i915 device info: has_guc_deprivilege: no <7> [41.529768] i915 device info: has_l3_ccs_read: no <7> [41.529770] i915 device info: has_l3_dpf: no <7> [41.529772] i915 device info: has_llc: yes <7> [41.529773] i915 device info: has_logical_ring_contexts: yes <7> [41.529775] i915 device info: has_logical_ring_elsq: no <7> [41.529777] i915 device info: has_media_ratio_mode: no <7> [41.529778] i915 device info: has_mslice_steering: no <7> [41.529780] i915 device info: has_oa_bpc_reporting: no <7> [41.529782] i915 device info: has_oa_slice_contrib_limits: no <7> [41.529784] i915 device info: has_oam: no <7> [41.529785] i915 device info: has_one_eu_per_fuse_bit: no <7> [41.529787] i915 device info: has_pxp: no <7> [41.529789] i915 device info: has_rc6: yes <7> [41.529791] i915 device info: has_rc6p: no <7> [41.529792] i915 device info: has_rps: yes <7> [41.529794] i915 device info: has_runtime_pm: yes <7> [41.529796] i915 device info: has_snoop: no <7> [41.529797] i915 device info: has_coherent_ggtt: yes <7> [41.529799] i915 device info: tuning_thread_rr_after_dep: no <7> [41.529801] i915 device info: unfenced_needs_alignment: no <7> [41.529803] i915 device info: hws_needs_physical: no <7> [41.529804] i915 device info: has_pooled_eu: no <7> [41.529806] i915 device info: cursor_needs_physical: no <7> [41.529808] i915 device info: has_cdclk_crawl: no <7> [41.529809] i915 device info: has_cdclk_squash: no <7> [41.529811] i915 device info: has_ddi: yes <7> [41.529813] i915 device info: has_dp_mst: yes <7> [41.529814] i915 device info: has_dsb: no <7> [41.529816] i915 device info: has_fpga_dbg: yes <7> [41.529818] i915 device info: has_gmch: no <7> [41.529820] i915 device info: has_hotplug: yes <7> [41.529821] i915 device info: has_hti: no <7> [41.529823] i915 device info: has_ipc: yes <7> [41.529825] i915 device info: has_overlay: no <7> [41.529826] i915 device info: has_psr: yes <7> [41.529828] i915 device info: has_psr_hw_tracking: yes <7> [41.529830] i915 device info: overlay_needs_physical: no <7> [41.529832] i915 device info: supports_tv: no <7> [41.529833] i915 device info: has_hdcp: yes <7> [41.529835] i915 device info: has_dmc: yes <7> [41.529837] i915 device info: has_dsc: no <7> [41.529838] i915 device info: rawclk rate: 24000 kHz <7> [41.529840] i915 device info: iommu: enabled <7> [41.529842] i915 device info: available engines: 40403 <7> [41.529844] i915 device info: slice total: 1, mask=0001 <7> [41.529846] i915 device info: subslice total: 3 <7> [41.529848] i915 device info: slice0: 3 subslices, mask=00000007 <7> [41.529850] i915 device info: slice1: 0 subslices, mask=00000000 <7> [41.529852] i915 device info: slice2: 0 subslices, mask=00000000 <7> [41.529854] i915 device info: EU total: 24 <7> [41.529856] i915 device info: EU per subslice: 8 <7> [41.529857] i915 device info: has slice power gating: no <7> [41.529859] i915 device info: has subslice power gating: no <7> [41.529861] i915 device info: has EU power gating: yes <6> [41.529863] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled <6> [41.529865] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled <6> [41.529867] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled <7> [41.529831] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [41.529984] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [41.530850] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [41.531059] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [41.531066] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [41.531697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [41.534671] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [41.534680] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [41.534858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [41.535127] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [41.535299] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [41.535493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [41.536074] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.536490] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected <7> [41.536674] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [41.537241] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [41.537258] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [41.537443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.538203] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [41.538343] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [41.538653] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [41.539079] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [41.539084] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [41.539301] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [41.554066] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [41.554074] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [41.554250] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.554431] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected <7> [41.554450] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [41.554463] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [41.554475] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [41.554617] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.555135] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.555462] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] status updated from unknown to disconnected <7> [41.555488] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [41.555505] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [41.555517] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [41.555522] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [41.555526] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [41.555614] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [41.555631] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [41.555650] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [41.555670] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [41.556461] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.556672] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [41.557145] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [41.557768] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [41.557917] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [41.558057] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [41.558651] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.558997] [drm:drm_client_modeset_probe] <7> [41.559217] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [41.559249] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [41.559521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.560769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [41.560931] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [41.561578] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [41.562069] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [41.562074] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [41.562202] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [41.576881] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [41.576889] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [41.577018] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.577195] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [41.577213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [41.577225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [41.577344] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.577966] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [41.578074] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [41.578386] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [41.578792] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [41.578797] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [41.578903] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [41.593558] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [41.593565] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [41.593712] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.593846] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [41.593864] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [41.593877] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [41.593996] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.594600] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.594755] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [41.594770] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [41.594777] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [41.594780] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [41.594783] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [41.594843] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [41.594855] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [41.594875] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [41.594892] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <7> [41.594979] [drm:drm_client_modeset_probe] <7> [41.595012] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] <7> [41.595025] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1] <7> [41.595145] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.595812] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [41.595923] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry <7> [41.596537] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1) <7> [41.597027] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [41.597032] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [41.597136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1 <7> [41.611837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb <7> [41.611843] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0 <7> [41.611968] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.612099] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected <7> [41.612115] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] <7> [41.612127] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2] <7> [41.612267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.612919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [41.613027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry <7> [41.613627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1) <7> [41.614104] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [41.614110] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [41.614244] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [41.628913] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [41.628919] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [41.629046] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.629199] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected <7> [41.629222] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] <7> [41.629240] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1] <7> [41.629371] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.629792] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [41.629925] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected <7> [41.629938] [drm:drm_client_modeset_probe] No connectors reported connected with modes <7> [41.629941] [drm:drm_client_modeset_probe] connector 95 enabled? no <7> [41.629944] [drm:drm_client_modeset_probe] connector 105 enabled? no <7> [41.629947] [drm:drm_client_modeset_probe] connector 109 enabled? no <7> [41.629976] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration <7> [41.629984] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config <7> [41.630001] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane <6> [41.630015] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes <6> [41.647181] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002) <7> [41.649098] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <6> [41.649631] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915]) <7> [41.649942] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [41.650054] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c] <7> [41.650119] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [41.650635] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [41.651186] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [41.651227] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [41.651490] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10 <6> [41.661105] [IGT] i915_module_load: finished subtest load, SUCCESS <6> [41.661148] [IGT] i915_module_load: exiting, ret=0 <6> [41.668858] i915_module_loa (943) used greatest stack depth: 11384 bytes left

<6> [40.646507] Console: switching to colour dummy device 80x25

<6> [40.646569] [IGT] i915_module_load: executing

<6> [40.825790] [IGT] i915_module_load: starting subtest load

<4> [41.332711] **********************************************************

<4> [41.332713] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [41.332716] ** trace_printk() being used. Allocating extra memory. **

<4> [41.332719] ** This means that this is a DEBUG kernel and it is **

<4> [41.332720] ** unsafe for production use. **

<4> [41.332723] ** If you see this message and you are not debugging **

<4> [41.332725] ** the kernel, report this immediately to your vendor! **

<4> [41.332728] ** NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE NOTICE **

<4> [41.332729] **********************************************************

<5> [41.343851] Setting dangerous option enable_guc - tainting kernel

<7> [41.386268] i915 0000:00:02.0: [drm:intel_gt_common_init_early [i915]] WOPCM: 1024K

<7> [41.386473] i915 0000:00:02.0: [drm:intel_uc_init_early [i915]] GT0: enable_guc=3 (guc:yes submission:no huc:yes slpc:no)

<6> [41.386617] i915 0000:00:02.0: [drm] GT0: Incompatible option enable_guc=3 - GuC submission is N/A

<7> [41.386629] i915 0000:00:02.0: [drm:intel_pch_type [i915]] Found SunrisePoint PCH

<7> [41.386772] i915 0000:00:02.0: [drm:intel_gt_probe_all [i915]] GT0: Setting up Primary GT

<7> [41.387063] i915 0000:00:02.0: [drm:intel_uncore_init_mmio [i915]] unclaimed mmio detected on uncore init, clearing

<7> [41.387230] i915 0000:00:02.0: [drm:intel_device_info_runtime_init [i915]] rawclk rate: 24000 kHz

<7> [41.388186] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GGTT size = 4096M

<7> [41.388299] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] GMADR size = 256M

<7> [41.388405] i915 0000:00:02.0: [drm:i915_ggtt_probe_hw [i915]] DSM size = 64M

<6> [41.388508] i915 0000:00:02.0: [drm] VT-d active for gfx access

<6> [41.390850] i915 0000:00:02.0: vgaarb: deactivate vga console

<6> [41.391445] i915 0000:00:02.0: [drm] Using Transparent Hugepages

<7> [41.391464] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] GEN6_STOLEN_RESERVED = c7f00047

<7> [41.391605] i915 0000:00:02.0: [drm:i915_gem_init_stolen [i915]] Memory reserved for graphics device: 65536K, usable: 64512K

<7> [41.391987] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] graphic opregion physical addr: 0xc2d24018

<7> [41.392144] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ACPI OpRegion version 2.0.0

<7> [41.392306] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Public ACPI methods supported

<7> [41.392480] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI Mailbox #2 present for opregion v2.x

<7> [41.392609] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI supported

<7> [41.397858] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] SWSCI GBDA callbacks 00000cb3, SBCB callbacks 00300483

<7> [41.398008] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE supported

<7> [41.398143] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] ASLE extension supported

<7> [41.398286] i915 0000:00:02.0: [drm:intel_opregion_setup [i915]] Found valid VBT in ACPI OpRegion (Mailbox #4)

<7> [41.398414] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] DRAM type: DDR4

<7> [41.398514] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [41.398611] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH0 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [41.398717] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH0 ranks: 1, 16Gb DIMMs: no

<7> [41.398840] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM L size: 32 Gb, width: X8, ranks: 1, 16Gb DIMMs: no

<7> [41.398960] i915 0000:00:02.0: [drm:skl_dram_get_dimm_info [i915]] CH1 DIMM S size: 0 Gb, width: X0, ranks: 0, 16Gb DIMMs: no

<7> [41.399060] i915 0000:00:02.0: [drm:skl_dram_get_channel_info [i915]] CH1 ranks: 1, 16Gb DIMMs: no

<7> [41.399175] i915 0000:00:02.0: [drm:skl_get_dram_info [i915]] Memory configuration is symmetric? yes

<7> [41.399294] i915 0000:00:02.0: [drm:intel_dram_detect [i915]] DRAM channels: 2

<7> [41.399388] i915 0000:00:02.0: [drm:i915_driver_probe [i915]] Watermark level 0 adjustment needed: no

<7> [41.399900] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Set default to SSC at 120000 kHz

<7> [41.400046] i915 0000:00:02.0: [drm:intel_bios_init [i915]] VBT signature "$VBT SKYLAKE ", BDB version 206

<7> [41.400213] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 1 (size 5, min size 7)

<7> [41.400408] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 2 (size 309, min size 5)

<7> [41.400553] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 9 (size 96, min size 100)

<7> [41.400693] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 12 (size 19, min size 19)

<7> [41.400875] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 27 (size 748, min size 812)

<7> [41.401047] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 40 (size 26, min size 34)

<7> [41.401204] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 41 (size 148, min size 148)

<7> [41.401382] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 42 (size 1282, min size 1366)

<7> [41.401555] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 43 (size 129, min size 305)

<7> [41.401698] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found BDB block 44 (size 21, min size 78)

<7> [41.401859] i915 0000:00:02.0: [drm:intel_bios_init [i915]] BDB_GENERAL_FEATURES int_tv_support 0 int_crt_support 0 lvds_use_ssc 0 lvds_ssc_freq 120000 display_clock_mode 0 fdi_rx_polarity_inverted 0

<7> [41.402035] i915 0000:00:02.0: [drm:intel_bios_init [i915]] crt_ddc_bus_pin: 2

<7> [41.402184] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [41.402346] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x60d2

<7> [41.402548] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Found VBT child device with type 0x68c6

<7> [41.402719] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Skipping SDVO device mapping

<7> [41.402862] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [41.403000] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port B VBT HDMI level shift: 4

<7> [41.403137] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT info: CRT:0 DVI:1 HDMI:1 DP:0 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [41.403340] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port C VBT HDMI level shift: 8

<7> [41.403512] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT info: CRT:0 DVI:0 HDMI:0 DP:1 eDP:0 DSI:0 LSPCON:0 USB-Type-C:0 TBT:0 DSC:0

<7> [41.403650] i915 0000:00:02.0: [drm:intel_bios_init [i915]] Port E VBT HDMI level shift: 0

<7> [41.403786] i915 0000:00:02.0: [drm:intel_power_domains_init [i915]] Allowed DC state mask 02

<7> [41.403984] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [41.404189] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_1

<7> [41.404357] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling MISC_IO

<7> [41.404553] i915 0000:00:02.0: [drm:intel_cdclk_init_hw [i915]] Sanitizing cdclk programmed by pre-os

<7> [41.405002] i915 0000:00:02.0: [drm:intel_update_max_cdclk [i915]] Max CD clock rate: 675000 kHz

<7> [41.405201] i915 0000:00:02.0: [drm:skl_set_cdclk [i915]] Max dotclock rate: 675000 kHz

<7> [41.405356] i915 0000:00:02.0: [drm:gen9_dbuf_slices_update [i915]] Updating dbuf slices to 0x1

<7> [41.405565] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.405740] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [41.405878] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 00

<7> [41.406024] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<6> [41.406227] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem

<7> [41.406287] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_A_E

<7> [41.406445] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_B

<7> [41.406583] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_C

<7> [41.406720] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DDI_IO_D

<7> [41.406959] i915 0000:00:02.0: [drm:intel_dmc_init [i915]] Loading i915/kbl_dmc_ver1_04.bin

<7> [41.408549] i915 0000:00:02.0: [drm:intel_fbc_init [i915]] Sanitized enable_fbc value: 1

<7> [41.408996] i915 0000:00:02.0: [drm:skl_sagv_disable [i915]] Disabling SAGV

<7> [41.409200] i915 0000:00:02.0: [drm:skl_wm_init [i915]] SAGV supported: yes, original SAGV block time: 30 us

<7> [41.409387] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM0 latency 2 (2.0 usec)

<7> [41.409570] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM1 latency 19 (19.0 usec)

<7> [41.409718] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM2 latency 28 (28.0 usec)

<7> [41.409846] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM3 latency 32 (32.0 usec)

<7> [41.409973] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM4 latency 63 (63.0 usec)

<7> [41.410099] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM5 latency 77 (77.0 usec)

<7> [41.410267] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM6 latency 83 (83.0 usec)

<7> [41.410452] i915 0000:00:02.0: [drm:intel_print_wm_latency [i915]] Gen9 Plane WM7 latency 99 (99.0 usec)

<6> [41.411866] i915 0000:00:02.0: [drm] Finished loading DMC firmware i915/kbl_dmc_ver1_04.bin (v1.4)

<7> [41.411994] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] 3 display pipes available.

<7> [41.413186] i915 0000:00:02.0: [drm:intel_cdclk_dump_config [i915]] Current CDCLK 337500 kHz, VCO 8100000 kHz, ref 24000 kHz, bypass 24000 kHz, voltage level 0

<7> [41.413440] i915 0000:00:02.0: [drm:i915_hdcp_component_bind [i915]] I915 HDCP comp bind

<6> [41.413595] mei_hdcp 0000:00:16.0-b638ab7e-94e2-4ea2-a552-d1c54b627f04: bound 0000:00:02.0 (ops i915_hdcp_ops [i915])

<7> [41.413706] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port A is not present

<7> [41.413862] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:94:DDI B/PHY B] using AUX B (platform default)

<7> [41.414003] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:94:DDI B/PHY B]

<7> [41.414128] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:94:DDI B/PHY B] Using DDC pin 0x5 (VBT)

<7> [41.414668] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:104:DDI C/PHY C] using AUX C (platform default)

<7> [41.414809] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] Adding HDMI connector on [ENCODER:104:DDI C/PHY C]

<7> [41.414950] i915 0000:00:02.0: [drm:intel_hdmi_init_connector [i915]] [ENCODER:104:DDI C/PHY C] Using DDC pin 0x4 (VBT)

<7> [41.415205] i915 0000:00:02.0: [drm:intel_modeset_init_nogem [i915]] VBT says port D is not present

<7> [41.415361] i915 0000:00:02.0: [drm:intel_dp_aux_ch [i915]] [ENCODER:108:DDI E/PHY E] using AUX A (VBT)

<7> [41.415542] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] Adding DP connector on [ENCODER:108:DDI E/PHY E]

<7> [41.415808] i915 0000:00:02.0: [drm:intel_dp_init_connector [i915]] PSR condition failed: Port not supported

<7> [41.416241] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:51:pipe A] hw state readout: disabled

<7> [41.416450] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:72:pipe B] hw state readout: disabled

<7> [41.416612] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CRTC:93:pipe C] hw state readout: disabled

<7> [41.416752] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] hw state readout: disabled, pipe A

<7> [41.416923] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] hw state readout: disabled, pipe A

<7> [41.417105] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] hw state readout: disabled, pipe A

<7> [41.417284] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] hw state readout: disabled, pipe B

<7> [41.417450] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] hw state readout: disabled, pipe B

<7> [41.417637] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] hw state readout: disabled, pipe B

<7> [41.417777] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] hw state readout: disabled, pipe C

<7> [41.417914] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] hw state readout: disabled, pipe C

<7> [41.418050] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] hw state readout: disabled, pipe C

<7> [41.418260] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:94:DDI B/PHY B] hw state readout: disabled, pipe A

<7> [41.418424] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:104:DDI C/PHY C] hw state readout: disabled, pipe A

<7> [41.418562] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [ENCODER:108:DDI E/PHY E] hw state readout: disabled, pipe A

<7> [41.418704] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 0 hw state readout: pipe_mask 0x0, on 1

<7> [41.418906] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 1 hw state readout: pipe_mask 0x0, on 0

<7> [41.419055] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 2 hw state readout: pipe_mask 0x0, on 0

<7> [41.419214] i915 0000:00:02.0: [drm:intel_dpll_readout_hw_state [i915]] DPLL 3 hw state readout: pipe_mask 0x0, on 0

<7> [41.419485] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:95:HDMI-A-1] hw state readout: disabled

<7> [41.419640] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:105:HDMI-A-2] hw state readout: disabled

<7> [41.419790] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [CONNECTOR:109:DP-1] hw state readout: disabled

<7> [41.419979] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:31:plane 1A] min_cdclk 0 kHz

<7> [41.420119] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:39:plane 2A] min_cdclk 0 kHz

<7> [41.420263] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:47:cursor A] min_cdclk 0 kHz

<7> [41.420439] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe A data rate 0 num active planes 0

<7> [41.420634] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:52:plane 1B] min_cdclk 0 kHz

<7> [41.420779] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:60:plane 2B] min_cdclk 0 kHz

<7> [41.420910] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:68:cursor B] min_cdclk 0 kHz

<7> [41.421039] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe B data rate 0 num active planes 0

<7> [41.421201] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:73:plane 1C] min_cdclk 0 kHz

<7> [41.421391] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:81:plane 2C] min_cdclk 0 kHz

<7> [41.421533] i915 0000:00:02.0: [drm:intel_modeset_setup_hw_state [i915]] [PLANE:89:cursor C] min_cdclk 0 kHz

<7> [41.421663] i915 0000:00:02.0: [drm:intel_bw_crtc_update [i915]] pipe C data rate 0 num active planes 0

<7> [41.421868] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:51:pipe A] enable: no [setup_hw_state]

<7> [41.422054] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:72:pipe B] enable: no [setup_hw_state]

<7> [41.422205] i915 0000:00:02.0: [drm:intel_crtc_state_dump [i915]] [CRTC:93:pipe C] enable: no [setup_hw_state]

<7> [41.422353] i915 0000:00:02.0: [drm:intel_dpll_sanitize_state [i915]] DPLL 0 enabled but not in use, disabling

<7> [41.422542] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:51:pipe A] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [41.422680] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:72:pipe B] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [41.422809] i915 0000:00:02.0: [drm:skl_wm_get_hw_state_and_sanitize [i915]] [CRTC:93:pipe C] dbuf slices 0x0, ddb (0 - 0), active pipes 0x0, mbus joined: no

<7> [41.428018] i915 0000:00:02.0: [drm:intel_wopcm_init [i915]] Calculated GuC WOPCM [240K, 784K)

<7> [41.428168] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] Reserved GGTT:[0, 2000] for use by error capture

<7> [41.428327] i915 0000:00:02.0: [drm:i915_init_ggtt [i915]] clearing unused GTT space: [2000, fee00000]

<7> [41.428451] i915 0000:00:02.0: [drm:gen9_gt_workarounds_init.isra.0 [i915]] MCR slice:0/subslice:0 = 0

<7> [41.428588] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 6 GT workarounds on global

<7> [41.429674] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 8 engine workarounds on rcs'0

<7> [41.429812] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 5 whitelist workarounds on rcs'0

<7> [41.429945] i915 0000:00:02.0: [drm:wa_init_finish [i915]] Initialized 14 context workarounds on rcs'0

<7> [41.433493] i915 0000:00:02.0: [drm:intel_guc_log_create [i915]] GT0: GUC: guc_log_level=5 (enabled, verbose:yes, verbosity:3)

<7> [41.433677] i915 0000:00:02.0: [drm:intel_guc_ads_create [i915]] GT0: GUC: Used 4 KB for temporary ADS regset

<7> [41.462307] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 0] = 0xc404f

<7> [41.462473] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 1] = 0x0

<7> [41.462608] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 2] = 0x4000

<7> [41.462741] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 3] = 0x3

<7> [41.462872] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 4] = 0x98a

<7> [41.463003] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 5] = 0x59120004

<7> [41.463134] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 6] = 0x0

<7> [41.463283] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 7] = 0x0

<7> [41.463470] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 8] = 0x0

<7> [41.463635] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[ 9] = 0x0

<7> [41.463768] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[10] = 0x0

<7> [41.463900] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[11] = 0x0

<7> [41.464059] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[12] = 0x0

<7> [41.464248] i915 0000:00:02.0: [drm:intel_guc_init [i915]] GT0: GUC: param[13] = 0x0

<7> [41.464383] i915 0000:00:02.0: [drm:intel_huc_init [i915]] GT0: HuC: loaded by GSC = no

<6> [41.465597] i915 0000:00:02.0: [drm] GT0: GuC firmware i915/kbl_guc_70.1.1.bin version 70.1.1

<6> [41.465601] i915 0000:00:02.0: [drm] GT0: HuC firmware i915/kbl_huc_4.0.0.bin version 4.0.0

<7> [41.478981] i915 0000:00:02.0: [drm:intel_guc_fw_upload [i915]] GT0: GUC: init took 9ms, freq = 100MHz, before = 100MHz, status = 0x8002F0EC, count = 0, ret = 0

<7> [41.479893] i915 0000:00:02.0: [drm:guc_enable_communication [i915]] GT0: GUC: communication enabled

<6> [41.490730] i915 0000:00:02.0: [drm] GT0: HuC: authenticated!

<6> [41.490734] i915 0000:00:02.0: [drm] GT0: GUC: submission disabled

<6> [41.490737] i915 0000:00:02.0: [drm] GT0: GUC: SLPC disabled

<7> [41.498515] i915 0000:00:02.0: [drm:intel_sagv_post_plane_update [i915]] Enabling SAGV

<7> [41.498761] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:51:pipe A] not active, skipping

<7> [41.498902] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:72:pipe B] not active, skipping

<7> [41.499036] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] [CRTC:93:pipe C] not active, skipping

<7> [41.499186] i915 0000:00:02.0: [drm:intel_fbdev_init [i915]] no active fbs found, not using BIOS config

<7> [41.499396] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [41.500019] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed rcs'0 to rcs0

<7> [41.500175] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed bcs'0 to bcs0

<7> [41.500280] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vcs'0 to vcs0

<7> [41.500381] i915 0000:00:02.0: [drm:engine_rename [i915]] renamed vecs'0 to vecs0

<7> [41.504123] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:95:HDMI-A-1] generating connector hotplug event

<7> [41.504560] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:105:HDMI-A-2] generating connector hotplug event

<7> [41.504979] i915 0000:00:02.0: [drm:intel_dp_connector_register [i915]] registering AUX A/DDI E/PHY E bus for card0-DP-1

<7> [41.505906] i915 0000:00:02.0: [drm:drm_sysfs_connector_hotplug_event] [CONNECTOR:109:DP-1] generating connector hotplug event

<6> [41.505972] [drm] Initialized i915 1.6.0 20201103 for 0000:00:02.0 on minor 0

<7> [41.507888] i915 0000:00:02.0: [drm:intel_opregion_resume [i915]] 3 outputs detected

<6> [41.523424] ACPI: video: Video Device [GFX0] (multi-head: yes rom: no post: no)

<6> [41.525610] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input3

<7> [41.527443] i915 0000:00:02.0: [drm:intel_audio_init [i915]] use AUD_FREQ_CNTRL of 0x10 (init value 0x10)

<7> [41.528263] [drm:drm_client_modeset_probe]

<7> [41.528223] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_D

<7> [41.528474] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [41.528435] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_C

<7> [41.528503] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [41.528634] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_B

<7> [41.528828] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DDI_IO_A_E

<7> [41.529568] [drm:intel_dsm_detect [i915]] no _DSM method for intel device

<7> [41.529710] i915 device info: pciid=0x5912 rev=0x04 platform=KABYLAKE (subplatform=0x0) gen=9

<7> [41.529714] i915 device info: graphics version: 9

<7> [41.529716] i915 device info: media version: 9

<7> [41.529718] i915 device info: display version: 9

<7> [41.529720] i915 device info: graphics stepping: F0

<7> [41.529721] i915 device info: media stepping: F0

<7> [41.529723] i915 device info: display stepping: C0

<7> [41.529725] i915 device info: base die stepping: **

<7> [41.529728] i915 device info: memory-regions: 0x21

<7> [41.529730] i915 device info: page-sizes: 0x11000

<7> [41.529732] i915 device info: platform: KABYLAKE

<7> [41.529734] i915 device info: ppgtt-size: 48

<7> [41.529735] i915 device info: ppgtt-type: 2

<7> [41.529737] i915 device info: dma_mask_size: 39

<7> [41.529739] i915 device info: is_mobile: no

<7> [41.529741] i915 device info: is_lp: no

<7> [41.529742] i915 device info: require_force_probe: no

<7> [41.529744] i915 device info: is_dgfx: no

<7> [41.529746] i915 device info: has_64bit_reloc: yes

<7> [41.529748] i915 device info: has_64k_pages: no

<7> [41.529749] i915 device info: gpu_reset_clobbers_display: no

<7> [41.529751] i915 device info: has_reset_engine: yes

<7> [41.529753] i915 device info: has_3d_pipeline: yes

<7> [41.529755] i915 device info: has_4tile: no

<7> [41.529756] i915 device info: has_flat_ccs: no

<7> [41.529758] i915 device info: has_global_mocs: no

<7> [41.529760] i915 device info: has_gmd_id: no

<7> [41.529761] i915 device info: has_gt_uc: yes

<7> [41.529763] i915 device info: has_heci_pxp: no

<7> [41.529765] i915 device info: has_heci_gscfi: no

<7> [41.529766] i915 device info: has_guc_deprivilege: no

<7> [41.529768] i915 device info: has_l3_ccs_read: no

<7> [41.529770] i915 device info: has_l3_dpf: no

<7> [41.529772] i915 device info: has_llc: yes

<7> [41.529773] i915 device info: has_logical_ring_contexts: yes

<7> [41.529775] i915 device info: has_logical_ring_elsq: no

<7> [41.529777] i915 device info: has_media_ratio_mode: no

<7> [41.529778] i915 device info: has_mslice_steering: no

<7> [41.529780] i915 device info: has_oa_bpc_reporting: no

<7> [41.529782] i915 device info: has_oa_slice_contrib_limits: no

<7> [41.529784] i915 device info: has_oam: no

<7> [41.529785] i915 device info: has_one_eu_per_fuse_bit: no

<7> [41.529787] i915 device info: has_pxp: no

<7> [41.529789] i915 device info: has_rc6: yes

<7> [41.529791] i915 device info: has_rc6p: no

<7> [41.529792] i915 device info: has_rps: yes

<7> [41.529794] i915 device info: has_runtime_pm: yes

<7> [41.529796] i915 device info: has_snoop: no

<7> [41.529797] i915 device info: has_coherent_ggtt: yes

<7> [41.529799] i915 device info: tuning_thread_rr_after_dep: no

<7> [41.529801] i915 device info: unfenced_needs_alignment: no

<7> [41.529803] i915 device info: hws_needs_physical: no

<7> [41.529804] i915 device info: has_pooled_eu: no

<7> [41.529806] i915 device info: cursor_needs_physical: no

<7> [41.529808] i915 device info: has_cdclk_crawl: no

<7> [41.529809] i915 device info: has_cdclk_squash: no

<7> [41.529811] i915 device info: has_ddi: yes

<7> [41.529813] i915 device info: has_dp_mst: yes

<7> [41.529814] i915 device info: has_dsb: no

<7> [41.529816] i915 device info: has_fpga_dbg: yes

<7> [41.529818] i915 device info: has_gmch: no

<7> [41.529820] i915 device info: has_hotplug: yes

<7> [41.529821] i915 device info: has_hti: no

<7> [41.529823] i915 device info: has_ipc: yes

<7> [41.529825] i915 device info: has_overlay: no

<7> [41.529826] i915 device info: has_psr: yes

<7> [41.529828] i915 device info: has_psr_hw_tracking: yes

<7> [41.529830] i915 device info: overlay_needs_physical: no

<7> [41.529832] i915 device info: supports_tv: no

<7> [41.529833] i915 device info: has_hdcp: yes

<7> [41.529835] i915 device info: has_dmc: yes

<7> [41.529837] i915 device info: has_dsc: no

<7> [41.529838] i915 device info: rawclk rate: 24000 kHz

<7> [41.529840] i915 device info: iommu: enabled

<7> [41.529842] i915 device info: available engines: 40403

<7> [41.529844] i915 device info: slice total: 1, mask=0001

<7> [41.529846] i915 device info: subslice total: 3

<7> [41.529848] i915 device info: slice0: 3 subslices, mask=00000007

<7> [41.529850] i915 device info: slice1: 0 subslices, mask=00000000

<7> [41.529852] i915 device info: slice2: 0 subslices, mask=00000000

<7> [41.529854] i915 device info: EU total: 24

<7> [41.529856] i915 device info: EU per subslice: 8

<7> [41.529857] i915 device info: has slice power gating: no

<7> [41.529859] i915 device info: has subslice power gating: no

<7> [41.529861] i915 device info: has EU power gating: yes

<6> [41.529863] i915 0000:00:02.0: [drm] DRM_I915_DEBUG enabled

<6> [41.529865] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_GEM enabled

<6> [41.529867] i915 0000:00:02.0: [drm] DRM_I915_DEBUG_RUNTIME_PM enabled

<7> [41.529831] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [41.529984] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [41.530850] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [41.531059] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [41.531066] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [41.531697] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [41.534671] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [41.534680] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [41.534858] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2

<7> [41.535127] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [41.535299] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [41.535493] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [41.536074] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.536490] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] status updated from unknown to disconnected

<7> [41.536674] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [41.537241] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [41.537258] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [41.537443] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.538203] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [41.538343] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [41.538653] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [41.539079] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [41.539084] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [41.539301] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [41.554066] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [41.554074] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [41.554250] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.554431] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] status updated from unknown to disconnected

<7> [41.554450] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [41.554463] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [41.554475] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [41.554617] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.555135] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.555462] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] status updated from unknown to disconnected

<7> [41.555488] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [41.555505] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [41.555517] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [41.555522] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [41.555526] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [41.555614] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [41.555631] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [41.555650] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [41.555670] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [41.556461] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.556672] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [41.557145] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [41.557768] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off

<7> [41.557917] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6

<7> [41.558057] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02

<7> [41.558651] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.558997] [drm:drm_client_modeset_probe]

<7> [41.559217] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [41.559249] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [41.559521] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.560769] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [41.560931] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [41.561578] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [41.562069] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [41.562074] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [41.562202] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [41.576881] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [41.576889] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [41.577018] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.577195] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [41.577213] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [41.577225] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [41.577344] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.577966] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [41.578074] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [41.578386] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [41.578792] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [41.578797] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [41.578903] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [41.593558] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [41.593565] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [41.593712] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.593846] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [41.593864] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [41.593877] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [41.593996] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.594600] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.594755] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [41.594770] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [41.594777] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [41.594780] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [41.594783] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [41.594843] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [41.594855] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [41.594875] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [41.594892] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<7> [41.594979] [drm:drm_client_modeset_probe]

<7> [41.595012] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1]

<7> [41.595025] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:95:HDMI-A-1]

<7> [41.595145] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.595812] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [41.595923] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK on first message, retry

<7> [41.596537] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpb] NAK for addr: 0050 w(1)

<7> [41.597027] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [41.597032] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [41.597136] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpb. force bit now 1

<7> [41.611837] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpb

<7> [41.611843] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpb. force bit now 0

<7> [41.611968] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.612099] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:HDMI-A-1] disconnected

<7> [41.612115] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2]

<7> [41.612127] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:105:HDMI-A-2]

<7> [41.612267] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.612919] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [41.613027] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK on first message, retry

<7> [41.613627] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] NAK for addr: 0050 w(1)

<7> [41.614104] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [41.614110] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging

<7> [41.614244] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1

<7> [41.628913] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc

<7> [41.628919] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0

<7> [41.629046] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.629199] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:105:HDMI-A-2] disconnected

<7> [41.629222] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1]

<7> [41.629240] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:109:DP-1]

<7> [41.629371] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.629792] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on

<7> [41.629925] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:109:DP-1] disconnected

<7> [41.629938] [drm:drm_client_modeset_probe] No connectors reported connected with modes

<7> [41.629941] [drm:drm_client_modeset_probe] connector 95 enabled? no

<7> [41.629944] [drm:drm_client_modeset_probe] connector 105 enabled? no

<7> [41.629947] [drm:drm_client_modeset_probe] connector 109 enabled? no

<7> [41.629976] [drm:drm_client_firmware_config.isra.0] Not using firmware configuration

<7> [41.629984] [drm:drm_client_modeset_probe] picking CRTCs for 16384x16384 config

<7> [41.630001] i915 0000:00:02.0: [drm:__drm_fb_helper_initial_config_and_unlock [drm_kms_helper]] test CRTC 0 primary plane

<6> [41.630015] i915 0000:00:02.0: [drm] Cannot find any crtc or sizes

<6> [41.647181] snd_hda_intel 0000:00:1f.3: enabling device (0000 -> 0002)

<7> [41.649098] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<6> [41.649631] snd_hda_intel 0000:00:1f.3: bound 0000:00:02.0 (ops i915_audio_component_bind_ops [i915])

<7> [41.649942] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on

<7> [41.650054] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x0000005c [0x0000005c]

<7> [41.650119] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off

<7> [41.650635] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00

<7> [41.651186] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2

<7> [41.651227] i915 0000:00:02.0: [drm:i915_gem_open [i915]]

<7> [41.651490] i915 0000:00:02.0: [drm:i915_audio_component_get_power [i915]] restored AUD_FREQ_CNTRL to 0x10

<6> [41.661105] [IGT] i915_module_load: finished subtest load, SUCCESS

<6> [41.661148] [IGT] i915_module_load: exiting, ret=0

<6> [41.668858] i915_module_loa (943) used greatest stack depth: 11384 bytes left

Results for igt@i915_module_load@load