Results for igt@kms_cursor_legacy@basic-busy-flip-before-cursor-legacy

Result: Skip

git-log-oneline igt_runner0 run0 runtimes0 results0.json boot0 dmesg0

Detail	Value
Igt-Version	IGT-Version: 1.27.1-gb7d168f61 (x86_64) (Linux: 6.4.0-rc7-linus-v6.4-rc7-g45a3e24f65e9+ x86_64)
Out	Opened device: /dev/dri/card0 No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. No valid crtc/connector combinations found. Subtest basic-busy-flip-before-cursor-legacy: SKIP (0.000s) No valid crtc/connector combinations found.
Err	Subtest basic-busy-flip-before-cursor-legacy: SKIP (0.000s)
Dmesg	<6> [111.466558] [IGT] kms_cursor_legacy: executing <7> [111.469660] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [111.470764] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc] <7> [111.471102] i915 0000:00:02.0: [drm:i915_gem_open [i915]] <7> [111.477560] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [111.477584] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [111.477893] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.478469] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [111.479008] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [111.479605] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [111.480329] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [111.480518] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [111.481612] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.483234] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.484795] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.486387] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.488161] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.490072] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.491827] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.493654] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.495273] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.496179] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [111.497104] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [111.497743] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [111.498350] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [111.498671] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [111.498971] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [111.499237] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [111.499951] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.500244] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [111.501380] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [111.501409] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [111.501694] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.502312] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.502601] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [111.503716] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [111.503742] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [111.504044] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.555007] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [111.572087] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.572097] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [111.572362] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [111.589430] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.589439] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [111.589702] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.590014] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <7> [111.590831] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] <7> [111.590859] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:95:DP-1] <7> [111.591146] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.591751] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling DC_off <7> [111.592349] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 02 to 00 <7> [111.592970] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling PW_2 <7> [111.593823] i915 0000:00:02.0: [drm:lspcon_wake_native_aux_ch [i915]] Native AUX CH up, DPCD version: 1.2 <7> [111.594108] i915 0000:00:02.0: [drm:lspcon_resume [i915]] LSPCON recovering in PCON mode after 0 ms <7> [111.595137] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.596822] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.598251] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.599817] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.601643] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.603465] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.605149] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.607020] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.608694] i915 0000:00:02.0: [drm:drm_dp_i2c_do_msg [drm_display_helper]] AUX B/DDI B/PHY B: native defer <7> [111.609589] i915 0000:00:02.0: [drm:lspcon_wait_mode [i915]] Current LSPCON mode PCON <7> [111.610574] i915 0000:00:02.0: [drm:drm_dp_read_dpcd_caps [drm_display_helper]] AUX B/DDI B/PHY B: DPCD: 12 14 c4 01 01 15 01 81 00 00 04 00 0f 00 04 <7> [111.611362] i915 0000:00:02.0: [drm:drm_dp_read_desc [drm_display_helper]] AUX B/DDI B/PHY B: DP branch: OUI 00-60-ad dev-ID MC2800 HW-rev 2.2 SW-rev 1.72 quirks 0x0000 <7> [111.611899] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling PW_2 <7> [111.612131] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling DC_off <7> [111.612341] i915 0000:00:02.0: [drm:skl_enable_dc6 [i915]] Enabling DC6 <7> [111.612606] i915 0000:00:02.0: [drm:gen9_set_dc_state.part.0 [i915]] Setting DC state from 00 to 02 <7> [111.613302] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.613529] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:95:DP-1] disconnected <7> [111.613584] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] <7> [111.613600] i915 0000:00:02.0: [drm:intel_dp_detect [i915]] [CONNECTOR:108:DP-2] <7> [111.614089] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.614609] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.614844] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:108:DP-2] disconnected <7> [111.614901] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] <7> [111.614924] i915 0000:00:02.0: [drm:intel_hdmi_detect [i915]] [CONNECTOR:114:HDMI-A-1] <7> [111.615109] i915 0000:00:02.0: [drm:intel_power_well_enable [i915]] enabling always-on <7> [111.667012] i915 0000:00:02.0: [drm:do_gmbus_xfer [i915]] GMBUS [i915 gmbus dpc] timed out, falling back to bit banging on pin 4 <7> [111.682988] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.682997] i915 0000:00:02.0: [drm:intel_hdmi_set_edid [i915]] HDMI GMBUS EDID read failed, retry using GPIO bit-banging <7> [111.683175] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] enabling bit-banging on i915 gmbus dpc. force bit now 1 <7> [111.699047] [drm:drm_do_probe_ddc_edid] drm: skipping non-existent adapter i915 gmbus dpc <7> [111.699054] i915 0000:00:02.0: [drm:intel_gmbus_force_bit [i915]] disabling bit-banging on i915 gmbus dpc. force bit now 0 <7> [111.699228] i915 0000:00:02.0: [drm:intel_power_well_disable [i915]] disabling always-on <7> [111.699425] [drm:drm_helper_probe_single_connector_modes [drm_kms_helper]] [CONNECTOR:114:HDMI-A-1] disconnected <6> [111.700194] [IGT] kms_cursor_legacy: exiting, ret=77 <7> [111.700626] i915 0000:00:02.0: [drm:i915_drop_caches_set [i915]] Dropping caches: 0x000001dc [0x000001dc]

Created at 2023-06-18 23:06:06